Agri-Fab 45-0414 User's Manual
Contents
1. CALIBRATING FLOW CONTROL ARM Flow control mounting bracket figure 16 and 17 a Setadjustable stop at OFF position Move flow control arm against adjustable stop b Slide flow control mounting bracket along control tube until closure plate in bottom of hopper just closes c Snugthe nuts just enough to hold flow control mounting bracket in place d Setadjustable stop at 5 With flow control arm resting against stop verify that closure plate is open about half way e If closure plate is not open about half way slide flow control mounting bracket up or down control tube until closure plate will open about half way at 5 and will close completely when arm is pushed past adjustable stop to OFF position Tighten the 5 16 nylock hex nuts FIGURE 17 OPERATION HOW TO USE YOUR SPREADER SETTING THE FLOW CONTROL Refer to figure 16 and 17 1 Loosen the nylon wing nut set the adjustable stop to the desired flow rate setting and retighten the wing nut The higher the setting number the wider the opening in the bottom of the hopper 2 Refer to the Application Chart on page 8 and to the instructions on the fertilizer bag to select the proper flow rate setting 3 Pull the flow control arm from the OFF position and rest it against the adjustable stop for the ON position Push the flow control arm past the stop toward the hopper for the OFF position USING THE PATTERN ADJUSTMENT PLATE The pattern adjustment p2. Agriefah OWNERS MANUAL Model No 45 0414 45 0415 125 LB TOW BROADCAST SPREADER Safety CAUTION ey Read Rules for Operation Safe Operation Maintenance and Instructions Parts Carefully Speed P df 7 the fastest way to purchase parts www speedepart com PRINTED IN USA FORM NO 40454 11 06 RULES FOR SAFE OPERATION Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment Exercise caution at all times when operating equipment Read the towing vehicle owners manual and towing vehicle safety rules Know how to operate your tractor before using the broadcast spreader attachment Read the chemical label instructions and cautions for handling and applying the chemicals purchased for spreading Wear eye and hand protection when handling and when applying lawn or garden chemicals Never operate tractor and spreader attachment without wearing substantial footwear and do not allow anyone to ride or sit on spreader attachment frame Follow maintenance and lubrication instructions as outlined in this manual Always begin with the transmission in first low gear and with the engine at low speed and gradually increase speed as conditions permit When towing broadcast spreader do not drive too close to a creek or ditch and be alert for holes and other hazards which could cause you to loose control of the broadcast spreader and tractor Before operating veh
3. bolts Loosen bolt through axle just enough that bracket W can TOOLS REQUIRED FOR ASSEMBLY pivot but will stay in place See figure 4 1 Pliers 2 7 16 Wrenches ro 2 1 2 Wrenches 2 9 16 Wrenches LONG END TO OUTSIDE reo TIGHTEN WITH WRENCHES REINFORCEMENT STRAP FIGURE 4 FIGURE 1 SMALL HOLE Assemble bent hitch braces and then straight hitch braces to inside of spreader frame Straight hitch braces must be to inside of bent hitch braces See figure 5 FIGURE 2 STRAIGHT HITCH LONG END BRACE TO INSIDE SMALL HOLE FIGURE 5 WITHOUT BOLT FIGURE 3 CONTROL TUBE SEE BOTTOM HITCH SHORT TIGHTEN FASTENERS Tighten fasteners in the order below FIGURE 8 FIGURE 9 FIGURE 6 FIGURE 8 FIGURE 9 DRAWBAR TUBE LOWER HANDLE TUBE E I eo lt tr E o TO Oq E c rm Assemble drawbar tubes to inside of lower handle tubes Assemble straight hitch braces to outside of lower handle tubes See figure 6 FIGURE 6 FIGURE 7 A FIGURE 11 FIGURE 12 FLOW CONTROL BRACKET LEE PELI 7 TT TA a f FIGURE 14 Slip the small spring X onto the end flow control rod and then attach it to the pattern plate See figure 15 FIGURE 15 CONTINUE TO NEXT PAGE TIGHTEN FASTENERS Tighten the nut H and then loosen FIGURE 11 ro just enough that the flow control arm moves freely
4. icle on any grade hill refer to the safety rules in the vehicle owner s manual concerning safe operation on slopes Stay off steep slopes Never allow children to operate the tractor or spreader attachment and do not allow adults to operate without proper instructions LOOK FOR THIS SYMBOL TO POINT OUT IMPORTANT SAFETY PRECAUTIONS IT MEANS ATTENTION BECOME ALERT YOUR SAFETY IS INVOLVED CARTON CONTENTS Drawbar Tube Flow Control Rod Bent Hitch Brace Flow Control Bracket Hopper Assembly Hopper Screen Straight Hitch Brace Control Tube RH Wheel LH Wheel Flow Control Arm Top Hitch tall Bottom Hitch short Reinforcement Strap HARDWARE PACKAGE REF GTY DESCRIPTION REFQIVIDESCRIPTION lt TAC IOMU00OU gt Hex Bolt 3 8 x 2 1 4 Hex Bolt 1 4 x 2 1 2 Hex Bolt 1 4 x 1 3 4 Hex Bolt 1 4 x 1 1 2 Hex Bolt 1 4 x 1 Nylock Nut 3 8 Nylock Nut 1 4 Nylon Washer Washer Small Hair Cotter Pin Carriage Bolt 1 4 20 x 3 4 Cotter Pin 9 64 x 1 1 2 2 CANO DOuOZ X A dl ld dl dl dl a gt a Spacer 64 x 84 x 1 Spacer 64 x 1 x 2 94 Washer Large Wing Nut 1 4 Spacer 39 x 56 x 62 Spring Adjustable Stop Grip Hitch Pin Engagement Bracket Spring ASSEMBLY INSTRUCTIONS After assembling bracket W to axle tighten both
5. late is used to adjust the flow of material being spread to the left or right side The pattern adjustment plate is the bottom stainless steel plate underneath the hopper The adjustment of the pattern plate is sensitive It is recommended that you test your spread pattern in a small area first 1 To adjust the flow to be heavier to the left side tighten the thumbscrew so the plate will not pull out as far See figure 18 2 To adjust the flow to be heavier to the right side loosen the thumbscrew so the plate will pull out farther See figure 18 e LE GLE lt a LZ LE T Zt N FIGURE 18 USING YOUR SPREADER The due use of powdered lawn chemicals is not recommended to difficulty in obtaining a satisfactory or consistent broadcast pattern 1 2 o eA 10 Determine approximate square footage of area to be covered and estimate amount of material required Before filling the hopper set the adjustable stop to the proper setting Refer to the Application Charton this page and to the instructions on the fertilizer bag to select the proper flow rate setting Move the flow control arm past the adjustable stop to the OFF position so that the closure plate is shut Fill the hopper breaking up any lumpy fertilizer The Application Chart is calculated for light to heavy application at a walking speed of 3 mph or 100 ft in 23 seconds A variation in speed will require an adjustment ofthe flow
6. n assembling the axle components Add grease to gears 2 If the agitator hairpin becomes damaged or worn it can be replaced Remove old agitator hairpin from hole in impeller shaft and replace with new agitator hairpin See figure 21 SPROCKET AGITATOR HAIRPIN FIGURE 21 REPAIR PARTS FOR BROADCAST SPREADER MODELS 45 0414 45 0415 REPAIR PARTS FOR BROADCAST SPREADER MODELS 45 0414 45 0415 per van no arv oescmenon Re pan No ary pesomienon 44466 48842 4884288 25755 2575588 741 0249 1543 69 49890 25672 49891 49892 65457 25757 23533 44285 49894 43882 49895 25758 25917 40199 04367 49896 26027 49910 49798 47212 47204 47209 47205 49897 49898 46055 43659 49899 40304 Stainless Steel Fastener Hopper Spreader 125 Ib Tube Frame 45 0414 Tube Frame 45 0415 Handle Lower 45 0414 Handle Lower 45 0415 Bearing Flanged Washer Nylon Washer 1 4 Clip Nylock Nut 1 4 20 Hex Bolt 1 4 20 x 1 3 4 Closure Guide Plate Pattern Plate Closure Bushing Hopper Bottom Slot Truss Bolt 10 32 x 1 2 Pop Rivet 3 16 Nylock Nut 10 32 Link Flow Control Slide Gate Angle Bracket Hex Bolt 1 4 20 x 3 4 Spreader Impeller Shaft Impeller Axle Spacer Axle Tube Fitting Grease 1 4 Housing Large Gear Yoke Large Gear Large Gear Small Clip Hairpin 7 8 Clip Hairpin 5 8 Pin Spring 1 8 x 1 Pin Spring 3 16 x 1 Washer Rod Flow Cont
7. rate to maintain the same coverage The faster you travel the wider the broadcast width Always start the spreader in motion before opening the closure plate Always shut the closure plate before turning or stopping the spreader If fertilizer is accidentally deposited too heavily in a small area soak the area thoroughly with a garden hose or sprinkler to prevent burning of the lawn To insure uniform coverage make each pass so that the broadcast pattern slightly overlaps the pattern from the previous pass as shown in figure 19 The approximate broadcast widths for different materials are shown in the Application Diagram figure 19 When broadcasting weed controlfertilizers make sure the broadcast pattern does not hit evergreen trees flowers or shrubs CHARTS j N gt FIGURE 19 IMPORTANT Application rates shown in the chart are affected by humidity and by the moisture content of the material granular and pellet Some minor setting adjustments may be necessary to compensate for this condition APPLICATION CHART MATERIAL FLOW SETTING SPREAD TYPE 3 MPH WIDTH IN 100 FT IN 23 SEC FEET FERTILIZER Powder Granular Pelleted Organic GRASS SEED Fine Coarse ICE MELTER OPERATING SPEED 3 MPH 100 ft in 23 seconds MAINTENANCE CHECK FOR LOOSE FASTENERS 1 Before each use make a thorough visual check of the spreader for any bolts and nuts which may have loosened Retighten any loose bolts and n
8. rol 23668 48857 48934 25763 49903 49931 47141 43848 49901 49908 49909 40520 23525 23014 23687 40305 40306 40308 40310 26026 23658 26023 49911 23353 43343 40291 4029188 40292 4029288 40355 44695 47441 24915 26004 26142 40526 40454 A A A LA n NN A A NN 4 N A A 4 bb pypyny py 0qQ A l M Spacer 64 x 1 x 2 94 Spacer 64 x 84 x 1 Hairpin Agitator Adjustable Stop Carriage Bolt 1 4 20 x 3 4 Thumb Screw 1 4 20 x 1 1 4 Wing Nut 1 4 20 Control Arm Grip Spring Hex Bolt 1 4 20 x 2 1 2 Hex Bolt 1 4 20 x 1 1 2 Nylon Nut Hitch Brace bent Hitch Bracket Hitch Bracket Hex Bolt 3 8 16 x 2 1 4 Nylock Nut 3 8 16 Washer 3437 x 6875 Hex Bolt 1 4 20 x 1 Engagement Bracket Spacer 39 x 56 x 62 Hitch Brace straight Cotter Pin 9 64 x 1 1 2 Hitch Pin 3 8 x 3 Hair Cotter Pin 3 32 x 2 5 16 Drawbar Tube 45 0414 Drawbar Tube 45 0415 Control Tube 45 0414 Control Tube 45 0415 Wheel Bowed Washer Spreader Screen Flow Control Bracket Control Arm Cross Frame Strap Spring Owners Manual SpeedEP ar 7 the fastest way to purchase parts WWW Speedepart com 11 SpeedEP ai 7 the fastest way to purchase parts wWww speedepart com REPAIR PARTS Agri Fab Inc 809 South Hamilton Sullivan IL 61951 217 728 8388 O 2006 Agri Fab Inc www agri fab com
9. uts CHECK FOR WORN OR DAMAGED PARTS 2 Check for worn or damaged parts before each use Repair or replace parts if necessary CHECK TIRE INFLATION 3 Checkiftires are adequately inflated before each use Do not inflate tires beyond maximum recommended pressure CAUTION DO NOT inflate tires beyond the maximum recommended pressure printed on side of tire CLEANING 4 Rinse inside of hopper and exterior of spreader and allow to dry before storing LUBRICATE See figure 20 5 Remove one small and two large hairpins and separate the gearbox housings 6 Lightly apply automotive grease as needed to the gears 7 Oil the nylon bushings on the vertical sprocket shaft Apply grease to the axle at least once a year or more often as needed 8 Oil idler wheel at least once a year or more often as needed 9 Install gearbox housings and secure with hairpins HAIRPIN FIGURE 20 STORAGE 1 Rinse inside of hopper and exterior of spreader and allow to dry before storing 2 Store in a clean dry area SERVICE AND ADJUSTMENTS 1 Ifthe axle and gear assembly is disassembled mark down the positions of the parts as they are removed The large gear position in relation to the small gear determines which direction the spreader plate will spin Be sure to reassemble them in their original positions Refer to parts exploded view on page 10 Ensure washer Refer to item 33 on page 10 and 11 is in place whe
Download Pdf Manuals
Related Search