Agri-Fab 45-02882 User's Manual
Contents
1. TONGUE 5 8 hex bolts one 1 4 flat washer and two 1 4 nylock nuts Do not tighten yet See figure 3 ek 7 Place the end of the hitch bracket two holes down 1 4 x 5 8 through the slot in the tongue Attach the hopper brace HEX BOLT to the top of the tongue and the hitch bracket to the bottom using one 3 8 x 1 hex bolt and 3 8 nylock nut 1 4 HEX NUT Tighten all bolts assembled so far See figure 3 FIGURE 1 1 4 FLAT WASHER ONE ONLY 3 Assemble the plastic grip onto the end ofthe flow control arm as shown in figure 2 4 Insertthe flow control arm through the slot in the hopper E brace Place a nylon washer on each side of the arm and attach it to the brace s welded bracket using a 1 4 lt NC 3 8 x 1 x 1 1 4 hex bolt a 1 4 flat washer and two 1 4 nylock 39 HEX BOLT nuts as shown in figure 2 Tighten the first nylock nut y I untilthere is noticeable resistance when moving the flow HITCH control arm then tighten the second nylock nut BRACKET 5 Place the flow control rod through the hole at the end of the flow control arm Assemble the two ferrules onto the threaded ends of the rod so that approximately 10 threads 1 2 of the rod extends through the ferrules See figure 2 3 8 NYLOCK NUT FIGURE 3 10 1 4 Assemble one end of a tongue brace to the side of the tongue using two 1 4 x 5 8 hex bolts and 1 4 nylock nuts Do not tighten yet See figure 4 Assemble the other end of the2. the safety rulesinthe vehicle owner s manual concerning safe operation on slopes Stay off steep slopes Follow maintenance and lubrication instructions as outlined in this manual Look for this symbol to point out important safety precautions It means Attention Become alert Your safety is involved CARTON CONTENTS gt Hopper Assembly Flow Control Gauge Hopper Brace Flow Control Arm Tongue Hitch Bracket Flow Control Rod Tongue Braces 2 SHOWN FULL SIZE FOO 0 lt NOT SHOWN FULL SIZE HARDWARE CHART DESCRIPTION DESCRIPTION Hex Bolt 3 8 x 1 Nylock Nut 1 4 Hex Bolt 1 4 x 1 1 4 Nylock Nut 3 8 Hex Bolt 1 4 x 3 4 Hitch Pin Hex Bolt 1 4 x 5 8 Hair Cotter Pin 1 8 Carriage Bolt 1 4 x 3 4 Plastic Knob Flat Washer 1 4 Plastic Grip Nylon Washer Ferrule ASSEMBLY 1 4 NYLOCK NUTS TOOLS REQUIRED FOR ASSEMBLY 1 4 x 1 1 4 PLASTIC HEX BOLT is GRIP 2 7 16 Wrenches 2 9 16 Wrenches 1 4 FLAT HOPPER WASHER E BRACE 1 Remove the hardware pack and all individual parts from the carton and lay out as shown on page 2 and 3 FLOW 2 Assemble the tongue to the hopper as shown in figure CONTROL 1 using two 1 4 x 5 8 hex bolts and 1 4 nylock nuts ROD Do not tighten yet FIGURE 2 6 Attach the hopper brace to the hopper using two 1 4 x
3. Lg Spacer 1 25 OD x 330 Lg Plate Bearing 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 40939 1509 69 47189 47712 24660 24542 63850 24532 23014 24531 43012 44950 1543 69 43849 43848 43001 21362 1509 90 47623 43343 40944 Wheel Bolt Hex 1 4 20 x 1 3 4 Lg Nylock Nut 1 4 20 Thd Rod Flow Control Arm Flow Control Gauge Flow Control Brace Assembly Hopper Brace Tongue Hitch Bracket Tongue Bolt Hex 1 4 20 x 3 4 Bolt Carriage 1 4 20 x 3 4 Lg Washer Nylon Knob Plastic 1 4 20 Thd Grip Plastic Bolt Hex 3 8 16 x 1 Lg Nut Hex Lock 3 8 16 Thd Bolt Hex 1 4 20 x 1 1 4 Lg Hitch Pin 3 8 Hair Cotter Pin 1 8 Owners Manual Speed P MIT e fastest way to purchase parts www speedepart com REPAIR PARTS 809 South Hamilton Sullivan IL 61951 217 728 8388 www agri fab com
4. Loosen the knob and adjust the flow control gauge to the recommended setting Retighten the knob See figure 7 Determine the approximate square footage of the area to be covered and estimate the amount of fertilizer or seed required Move the spreader to the area where application is to begin Making sure the flow control armis inthe OFF position fill the hopper breaking up any lumps Start the spreader in motion and then pull the flow control arm forward to the ON position as you travel across your lawn The recommended towing speed is 3 m p h IMPORTANT Always place flow control arm in the OFF position to prevent excessfertilizerfrom being released when filling the spreader and when stopping or turning FLOW CONTROL ARM FLOW RATE SETTING 6 PLASTIC KNOB FIGURE 7 SETTING CHART FLOW RATE MATERIAL TYPE AT 3 SETTING M P H Fertilizer Granular Pelleted 0 1 0 2 Grass Seed Fine Coarse 5 6 7 8 3 M PH is equivalent to traveling 100 feet in 23 seconds APPLICATION TIPS 1 NOTE To help prevent clogging when using granular material avoid towing the spreader with the flow plate closed A closed flow plate could cause the rotating agitator to work the material into powder compacting it at the bottom of the hopper Reduce the flow setting for speeds slower than 3 M PH and increase the setting for higher speeds To avoid misses or striping overlap the previous wheel tracks by ap
5. tongue brace to the triangular plate on the end of the spreader Use a 1 4 x 5 8 hex bolt and 1 4 nylock nut in the front hole of the plate Use a 1 4 x 3 4 hex bolt 1 4 flat washer and 1 4 nylock nut in the rear hole with the bolt and washer assembled on the inside of the hopper as shown in figure 4 Do not tighten yet Repeat steps 8 and 9 to attach the second tongue brace to the other end of the spreader and then tighten all loose bolts 1 4 FLAT WASHER s One per side QE 1 4 x 3 4 p HEX BOLT 1 4 x 5 8 HEX BOLT e 1 4 x 5 8 TONGUE BOLT BRACE 1 4 NYLOCK NUT FIGURE 4 11 Make sure that both ferrules are adjusted so that er approximately ten threads 1 2 of the control rod is exposed Insert both ferrules into the brackets which are riveted to the front of the flow plates Assemble a 1 4 nylock nut onto each ferrule making only finger tight at this time See figure 5 1 4 NYLOCK NUT Lone de FERRULE BRACKET FIGURE 5 12 Assemble the flow control gauge to the hopper brace using the 1 4 x 3 4 carriage bolt a nylon washer and the plastic knob See figure 6 13 Install the hitch pin and the 1 8 hair cotter pin in the spreader hitch bracket and tongue See figure 6 NYLON WASHER PLASTIC KNOB CONTROL GAUGE m 3 8 HITCH PIN 1 4 x 3 4 CARRIAGE BOLT 1 8 HAIR COTTER PIN FIGURE 6 14 To check for cor
6. Agriefal OWNERS MANUAL Model No 45 02882 175 LB POLY PRO DROP SPREADER CAUTION Read Rules for Safety Safe Operation Assembly and Instructions Operation Carefully e Maintenance e Parts Speed P MIT e fastest way to purchase parts www speedepart com PRINTED IN U S A FORM NO 40944 02 14 08 Exercise caution at all times when using power equipment RULES FOR SAFE OPERATIONS Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment Read this owner s manual before attempting to assemble or operate the spreader Read the towing vehicle owner s manual and know how to operate the tractor before using the spreader attachment Do not allow anyone to ride on or sit on spreader Never allow children to operate the tractor or spreader attachment Do not allow adults to operate the tractor or spreader without proper instructions Read the chemical label for instructions and cautions for handling and applying chemicals Wear eye and hand protection when handling and using lawn chemicals Always begin with the transmission in first low gear and gradually increase speed as conditions permit Maximum towing speed 6 Do not drive too close to a creek or ditch and be alert for holes and other hazards which could cause you to loose control of the tractor and spreader Before operating the vehicle on any grade hill refer to
7. proximately 4 5 The spread width of the spreader is approximately 40 For easiest application first apply material across both ends of the area Two or three passes on each end are sufficient Then apply material back and forth as shown Use the end areas for turning around shutting off the spreader as you enter the end areas and turning the spreader on again as your leave the end areas for your next pass See figure 8 If lawn is odd shaped spread a border around the edges and then spread between the border Be careful when using the spreader around ornamental plants because weed control chemicals can damage these plants FIGURE 8 MAINTENANCE 1 o RON Always empty spreader after each use storing leftover material in it s original bag Wash the spreader and dry thoroughly after each use Apply a few drops of oil to all moving parts Check all nuts and bolts for tightness before each use Keep tires inflated to 12 14 Ibs REPAIR PARTS FOR 175 LB DROP SPREADER MODEL 45 02882 a o gt N NHN O Base o N NN N nm Hopper Hopper Center Plate Small Hopper Center Plate Large Washer 1 4 Bolt Hex 1 4 20 x 5 8 Nut Hex SIMS 1 4 20 Thd Bearing Flange Bearing Hex Flange Bracket Feed Plate RH Bracket Feed Plate LH Ferrule Pop Rivet Skirt 48 Retainer Skirt Flow Plate Washer Agitator Blade Screw 8 32 x 3 8 Lg Axle Spacer Tube 1 OD x 1 65
8. rect opening of hopper flow plates a Set the flow control gauge at the highest setting b Move the flow control arm away from the hopper until it rests against the gauge The slots in the bottom of the hopper should now be completely open The edge of the flow plates should be just clear of the ends all the slots c Ifthe flow plates are not straight with the slots screw one ferrule up or down on one side of the control rod d Ifthe flow plates open to far or not far enough screw both ferrules equally up or down on the control rod d Move the flow control arm toward the hopper to the off position Verify that the slots in the bottom of the hopper are completely covered by the flow plates e Tighten the lock nuts and then loosen 1 4 turn 15 To check for proper tension on the hopper flow plates a Set the flow control gauge at a mid range setting b Move the flow control arm against the gauge c Press firmly against the front of the flow plates at the bottom of the hopper The flow control arm should not move d If the arm moves tighten the hex lock nuts on the flow control arm until movement is prevented OPERATION HOW TO USE YOUR SPREADER 1 Refer to the instruction label on the material package and to the instruction decal on your spreader to help determine the proper spreader setting and application rate Also see the Setting Chart on this page for a general range of settings for commonly used materials
Download Pdf Manuals
Related Search