Agri-Fab 45-01001 User's Manual
Contents
1. K FIGURE 10 17 Assemble hitch bracket to drawbar tongue using 3 8 x 1 long hex bolts 3 8 lock washers and 3 8 hex nuts See figure 11 3 8 x 1 HEX BOLTS HITCH BRACKET 3 8 LOCK WASHERS gt DRAW BAR TONGUE 3 8 HEX NUTS FIGURE 11 18 Assemble axle and draw bar tongue to wheel support keeping open side of tongue facing up make sure that latch lock snaps over latch stand Secure axle to wheel support or axle brackets using 1 4 x 1 1 2 long hex bolts and 1 4 her lock nuts See figure 12 114 x 1 1 2 WHEEL SUPPORT HEX BOLT 1 4 HEX LOCK NUT FIGURE 12 gt NOTE Position valve stem to outside when installing wheels on axle See figure 13 AXLE COTTER PIN 1 59 OD FLAT WASHER VALVE STEM outside 4 59 OD FLAT WASHER FIGURE 13 u A 19 Assemble wheels as described in step 19 using flat washers and cotter pins See figure 13 0 Turn cart assembly over to rest on wheels This completes the cart assembly Be sure to read safety rules and operating instructions before using your new utility cart GENERAL SAFETY PRECAUTIONS Preventing accidents is the responsibility of every equipment operator The following general safety precautions must be fully understood and followed by every operator 1 Do not at anytime carry passengers in this cart It is designed for carrying materials only and not intended to carry pas2. using 1 4 x 1 2 hex bolts and 1 4 hex lock nuts Bolt heads to inside of cart Leave out 2 13 Assemble two front top corner caps and two bolts in top flanges through tailgate reinforce ment bracket using 1 4 x 1 2 hex bolts and bolts for latch stand bracket See figure 6 1 4 hex lock nuts See figure 8 Tighten all bolts 14 Tighten all bolts assembled in steps 4 through 13 lower cart assembly to rest on top flanges with axle support up See figure 12 on page 6 LEAVE OUT 2 BOLTS LATCH STAND BRACKET LOCATION 1 4 x 1 2 HEX BOLTS 1 4 HEX LOCK NUTS er 1 4 x 1 4 HEX BOLT 114 x 1 2 HEX BOLT o FIGURE 8 15 Assemble two latch mount brackets latch lock and extension spring using one 1 4 x 3 4 hex bolt and 1 4 hex lock nut See figure 9 Do not tighen 1 4 lock nut latch lock must pivot freely j FIGURE 6 12 Assemble latch stand bracket using four 1 4 x 1 2 hex bolts and 1 4 hex lock nuts See figure 7 N LATCH MOUNT BRACKETS LATCH STAND BRACKET BOLT HEADS TO INSIDE OF CART 1 4 x 1 2 HEX BOLT 1 4 HEX LOCK NUT 1 4 x 3 14 HEX BOLT EXTENSION SPRING LATCH LOCK 1 4 HEX LOCK NUT FIGURE 7 FIGURE 9 16 Assemble latch lock subassembly to drawbar tongue using 1 4 x 1 2 long hex bolt and 1 4 hex lock nuts See figure 10 LATCH LOCK SUB ASSEMBLY HEX BOLT G HEX NUT L LOCK WASHER
3. OWNERS MANUAL Model No 45 01001 UTILITY CART IMPORTANT Read Rules for Safe Operation and Instructions Carefully e Assembly e Operation e Maintenance e Repair Parts Agri ms e 303 WEST RAYMOND SULLIVAN ILLINOIS 61951 PRINTED IN U S A FORM NO 45154 9 92 1 RULES FOR SAFE OPERATION Preventing accidents is the responsibility of every equipment operator The following general safety precautions must be fully understood and followed by every operator Do not at anytime carry passsengers in this cart It is designed for carrying materials only and not intended to carry passengers Do not tow this utility cart on a public thoroughfare at any time The operator is risk ing injury from passing vehicles Most local ordinances prohibit operating a cart and tractor such as this on a public thoroughfare Your utility cart carton and inner pack parts bag contain parts as shown in the figure below The hard ware package contains parts shown in figure 1 on page 3 Identify all parts and layout as shown in figure below and figure 1 CARTON CONTENTS LOOSE PARTS IN CARTON TAUN Cart Body 2 Tailgate Front Panel Draw Bar Tongue Wheel Support CARTON CONTENTS 3 1 NO When towing cart do not drive too close to a creek or ditch and be alert for holes and other hazards The above could cause you to lo control of the cart and tractor Be careful on any grade hill and stay off of steep gr
4. Tighten all six 6 bolts Position the wheel support in place on the bottom of cart See figure 3 Assemble wheel support to cart with eight 5 16 x 3 4 slotted head screws 5 16 lock washers and 5 16 hex nuts See figure 3 Heads of screws go to the inside of cart and Position the tailgate reinforcement bracket over end of cart See figure 5 Start 5 16 x 3 4 slotted screws through bottom of cart heads of screws to the insic of cart and reinforcement bracket Secure finger tight with 5 16 hex nuts and 5 16 lock washers See figure 4 Position the tailgate guides so that the holes line up with reinforcement bracket and cart body Refer to tailgate guide detail in figure 4 Secure tailgate guides with six 1 4 x 1 2 hex bolts and 1 4 hex lock nuts See figure 4 Tighten bolts assembled in steps 6 7 and 8 at this time Do not tighten others TAILGATE J y REINFORCEMENT 2 16 x 3 4 BRACKET should be tightened at this time ES A 5 16 HEX NUT 1 FF t amp 9 16 LOCK WASHER 474 HEX LOCK NUT FIGURE 4 10 Reverse the cart position and stand up on tailgate reinforcement bracket and proceed with 9 16 x 3 4 assembly steps 11 through 18 See figure 5 SLOTTED SCREW T WHEEL SUPPORT 5 16 LOCK WASHER 5 16 HEX NUT STAND CARTON i TAILGATE REINFORCEMENT BRACKET FIGURE 3 o FIGURE 5 11 Assemble front panel to open end of cart body
5. ades Maximum towing speed 10 M P H LOOK FOR THIS SYMBOL TO POINT OUT IMPORTANT SAFETY PRECAUTIONS IT MEANS ATTENTION BECOME ALERT YOUR SAFETY IS INVOLVED Wheels 2 Axle Tailgate Reinforcement Bracket Latch Stand Bracket PARTS IN INNER PACK BAG 10 11 12 13 14 15 Tailgate Guides 2 Corner Caps 2 Hitch Bracket Latch Lock Latch Mount Bracket 2 Hardware Package not shown un Cotter Pin 1 8 x 1 1 4 Long Washer 1 59 OD x 78 ID Hex Head Bolt 1 4 20 x 1 2 Long Hex Lock Nut 1 4 20 Thread Hex Nut 3 8 16 Thread Hex Head Bolt 3 8 16 x 1 Long Lock Washer 3 8 ASSEMBLY INSTRUCTIONS TOOLS REQUIRED FOR ASSEMBLY 1 1 2 2 2 Screwdriver Pliers 7 116 Open End or Box Wrenches 1 2 Open End or Box Wrenches 9 16 Open End or Box Wrenches Remove the hardware pack and all loose parts from the carton Be sure carton is empty before discarding Position cart body halves upright as shown in figure 2 EZ re TD a Hex Head Bolt 1 4 20 x 1 1 2 Long Slotted Truss Hd Bolt 5 16 18 x 3 4 Long Lock Washer 5 16 Hex Nut 5 16 18 Thread Hex Head Bolt 1 4 20 x 3 4 Long Extension Spring 1 4 x 1 2 HEX BOLTS HEX LOCK NUT CENTER FLANGES FIGURE 2 Start 1 4 x 1 2 hex bolts and 1 4 hex lock nuts through flanges only make finger tight until all six 6 bolts are in place See figure 2
6. h latch pivot bolt and the axle where the hitch tongue pivots with a light machine oil 1 Grease or oil wheel bearings occasionally Use automotive wheel bearing type grease or 20 weight oil 2 Recommended tire pressure is 12 14 Lbs REPAIR PARTS FOR UTILITY CART MODEL No 45 01001 PARTS LIST FOR UTILITY CART MODEL 45 01001 PART NO ai DESCRIPTION Cart Body Latch Mount Bracket Tailgate Tailgate Reinforcement Bracket Tailgate Guide Latch Lock Front Panel Wheel Support Latch Stand Bracket Extension Spring Hitch Bracket Draw Bar Tongue Axle 3 4 Diameter Front Corner Cap Hex Nut 3 8 16 Thread Wheel 4 30 x 3 75 Cotter Pin 1 8 x 1 1 4 Long Washer 1 59 OD x 78 1D Lock Washer 3 8 Hex Head Bolt 1 4 20 x 1 2 Long Hex Head Bolt 3 8 16 x 1 Long Hex Head Bolt 1 4 20 x 3 4 Long Hex Head Bolt 1 4 20 x 1 1 2 Long Hex Nut 5 15 18 Thread Hex Lock Nut 1 4 20 Thread Slotted Truss Head Bolt 5 16 18 x 3 4 Long Lock Washer 5 16 Owners Manual COON Oh GO N 1 1 2 1 1 1 1 1 1 1 1 2 2 2 2 4 2 34 2 1 2 Am REPAIR PARTS 303 West Raymond Street Sullivan Illinois 61951 217 728 8388 ae ON
7. ssengers 2 Do not tow this utility cart on a public thoroughfare at any time The operator is risk ing injury from passing vehicles Most local ordinances prohibit operating a cart and trac tor such as this on a public thoroughfare 3 When towing cart do not drive too close to a creek or ditch and be alert for holes and other hazards The above could cause you to lose con trol of the cart and tractor 4 Be careful on any grade hill and stay off of steep grades 5 Maximum towing speed 10 M PH mm NOTE Weighs limit See specifications for each model One cubic foot of dirt weighs approximately 150 Ibs Do Not exceed cart weight capacity of 650 Ibs OPERATION To dump material from the trailer box remove the tailgate by lifting it straight up and out from between the guides Release the spring latch by pulling the latch handle forward away from the trailer box CAUTION To avoid possible injury be sure that no one is near the trailer before releas ing latch A rope may be attached to the spring latch handle for easy release by the operator while on the tractor seat The trailer box will tilt backward to empty its contents After unloading pull the front of the box down toward the trailer tongue until the latch snaps in place Replace tailgate if desired gt NOTE For best handling do not load trailer too heavily behind center of axle MAINTENANCE At the beginning of each season lubricate the latc
Download Pdf Manuals
Related Search