AEG FAVORIT G 330 User's Manual
Contents
1. The distance between the bottom edge of the safety value and the floor on which the dishwasher is standing must be at least 30 cm The electrical cable for the safety valve is in the double walled water inlet hose Do not immerse the water inlet hose or the safety valve in water If water inlet hose or the safety valve is damaged remove the mains plug immediately A water inlet hose with safety valve must only be replaced by a specialist or by the consumer services department Place the water inlet hose in such a way that it is never higher than the bottom edge of the safety valve cs19 Installation instructions Water outlet hose connection The end of the drain hose can be connected in the following ways 1 To the sink outlet spigot securing it to the underside of the work surface This will prevent waste water from the sink running into the machine 2 Hooked over the edge of the sink using the special curved plastic guide provided 3 To a stand pipe provided with vent hole minimum internal diameter 4 cm The waste connection must be at a height of between 30 cm minimum and 100 cm maximum from the bottom of the dishwasher The drain hose can face either to the right or left of the dishwasher Ensure the hose is not bent or squashed as this could prevent or slow down the discharge of water The sink plug must not be in place when the machine is draining as this could cause the water to2. The dose is factory set in position 4 Reduce it if there are sticky whitish streaks on the dishes Filling with rinse aid Rinse aid dispenser type B 1 Open the container by turning the lid A anticlockwise 2 Fill with rinse aid exactly up to the level indicator marked max BRO1 Ensure the lid is closed after every refill Top up with rinse aid when the indicator B becomes clear Adjusting the dose According to the finish and drying results obtained adjust the dose of rinse aid by means of the 6 position selector C position 1 minimum dosage position 6 maximum dosage Increase the dose if there are drops of water or lime spots on the dishes after washing The dose is factory set in position 5 Reduce it if there are sticky whitish streaks on the dishes Operating instructions BRO2 Clean up any rinse aid spilt during filling with an absorbent cloth to avoid excess foaming during the next wash Only use branded rinse aid for dishwashers Never fill the rinse aid dispenser with any other substances e g dishwasher cleaning agent liquid detergent This would damage the appliance 55 Operating instructions 56 In daily use e Check if it s necessary to refill with special salt or rinse aid e Load cutlery and dishes into the dishwasher Fill with dishwasher detergent Select a wash prog
3. Avoid over tilting the machine during transportation 69 Operating instructions 70 What to do when Certain problems are due to the lack of simple maintenance or oversights which can be solved with the help of the instructions given here without calling out an engineer there are problems when operating the dishwasher The dishwasher will not start or stops during operation All push buttons are inoperative except for the On Off push button Press the On Off push button to switch the dishwasher off and carry out the following suggested corrective actions Malfunction The machine does not fill with water The dishwasher will not drain The programme does not start There is a whistling noise during washing Possible cause The water tap is blocked or furred with limescale The water tap is turned off The filter where present in the threaded hose fitting at the water inlet valve is blocked The water inlet hose has not been correctly laid or it is bent or squashed The siphon is blocked The water drain hose has not been correctly laid or it is bent or squashed The dishwasher door has not been properly closed The main plug is not plugged in The fuse has blown in the household fuse box The whistling is not a cause for concern Solutions Clean the water tap Turn the water tap on Clean the filter in the threaded hose fitting Check the water inlet hose co
4. FAVORIT G 330 Geschirrsp lautomat Dishwasher Benutzerinformation Instruction book 22 ao Dear customer Please read these user instructions carefully Above all please observe the safety instructions on the first few pages of these user instructions Please keep these user instructions for later reference Pass them on to any subsequent owner of the appliance The warning triangle and or specific words Warning caution Important are used to highlight instructions that are important for your safety or for the function of the appliance It is imperative that these instructions are observed Numbered instruction steps lead you step by step through the operation of the appliance Next to this symbol you receive additional information and practical tips on using the appliance Tips and instructions for the economical and environmentally conscious use of the appliance are marked with a clover leaf In the event of a malfunction these operating instructions contain information on how to rectify faults yourself see What to do when section If these instructions are insufficient please contact your nearest customer service centre In the case of technical problems our customer service organisation is available to provide you with assistance at any time Printed on paper manufactured with environmentally sound processes He who thinks ecologically acts accordingly Safety instructions Dispo
5. D back in the base of the washing compartment 8 Place the coarse filter A in the microfilter C and press together 9 Put the filter combination in place and lock by turning the handle clockwise to the stop During this process ensure that the flat filter does not protrude above the base of the washing compartment Under no circumstances may the dishwasher be used without filters Incorrect repositioning and fitting of the filters will produce poor washing results To ensure a correct working of the dishwasher NEVER try to remove the upper spray arm If residues of soil have clogged the holes in the upper spray arm remove them with a toothpick Operating instructions Prolonged periods of non operation If you are not using the machine for any period of time you are advised to 1 Unplug the appliance and then turn off the water 2 Fill the rinse aid dispenser 3 Leave the door ajar to prevent the formation of any unpleasant smells 4 Leave the inside of the machine clean Frost precautions Avoid placing the machine in a location where the temperature is below 0 C If this is unavoidable empty the machine close the appliance door disconnect the water inlet pipe and empty it Moving the machine If you have to move the machine moving house etc 1 Unplug it 2 Turn the water tap off 3 Remove the water inlet and discharge hoses 4 Pull the machine out together with the hoses
6. a cold water supply A hot water supply is not always efficient with very soiled crockery as it shortens the washing programmes a lot The dishwasher must not be connected to open hot water appliances or instantaneous water heaters The dishwasher is fitted with safety devices that prevent the wash water returning into the drinking water system and comply with the applicable plumbing regulations The water pressure must be within the limits given in the technical specifications Your local Water Authority will advise you on the average mains pressure in your area The dishwasher features fill and drain hoses which can be turned either to the left or the right to suit the installation The water inlet hose must not be kinked crushed or entangled when it is being connected up If the machine is connected to new pipes or pipes which have not been used for a long time you should run the water for a few minutes before connecting the inlet hose Do not use for connection old hoses which have been used in another appliance 15 Installation instructions 76 Water inlet hose with safety valve After connecting the double walled water inlet hose the safety valve is next to the tap Therefore the water inlet hose is only under pressure while the water is running If the water inlet hose starts to leak during this operation the safety valve cuts off the running water Please take care when installing the water inlet hose
7. advice These products are tablets with integrated and combined detergent rinse aid and salt functions 1 Before using these products you should first check that the water hardness in your supply is compatible with the use of these products as per the detergent manufacturers on the product packaging 2 These products should be strictly used according to the detergent manufacturers instructions 3 If you encounter problems when using 3 in 1 products for the first time then please contact the detergent manufacturers care line the telephone number is given on the product packaging Special advice If you decide to turn back to the use of the standard detergent system we advise that you e Refill both the salt container and rinse aid dispenser e Switch the water hardness setting to the highest possible position and run a normal washing programme without a load e Readjust the water hardness setting again according to the hardness of the water in your area 63 Operating instructions Washing programmes Choose the most suitable wash programme with the aid of this table Crockery and Type of load Crockery cutlery pots and pans cutlery Any in addition z z Degree of Heavy soil Normal soil Fresh soil Partial load to be soiling completed later in the day Suitable 1 Programme Normal 65 Deals 2 Rinse and Hold with prewash no prewash 30 minute 65 Position of the programme A B c D selec
8. consumer care line 71 Operating instructions 72 Technical specifications Capacity 12 place settings Water supply pressure Minimum 50 kPa 0 5 bar Maximum 800 kPa 8 bar Electrical connection Information on the electrical connection is given on the Voltage rating plate on the inner edge of the dishwasher s door on Overall power the right Fuse Dimensions 820 850 x 600 x 610 H x W x Din mm 73 23 or 19 2 73 Low Voltage Directive and subsequent modifications 89 336 or 3 5 89 Electromagnetic Compatibility Directive and subsequent modifications C This appliance complies with the following E E C Directives Operating instructions Hints for test centres Testing in accordance with EN 60704 must be carried out with appliance fully loaded and using the test programme see Washing programmes chart Testing in accordance with EN 60242 must be carried out when the salt dispenser and rinse aid container have been filled with salt and rinse aid respectively and using the test programme see Washing programmes chart Load 12 standard place settings Rinse aid setting Rinse aid dispenser type A Position 4 type II Rinse aid dispenser type B Position 5 type III Detergent dosage 5 g 25 g type B Arrangement cutlery basket Arrangement lower basket 73 Installation instructions 74 N Any electrical and or plumbing work required to install thi
9. dishwasher when its door is open Your dishwasher in day to day use e Never operate your dishwasher if the electrical supply lead supply or drain hose control panel worktop or plinth are damaged e f there is a fault first turn the water tap off Then switch off your machine and pull the plug out of the socket If there is a fixed connection switch off or unscrew the fuse s e Never pull the plug out of the socket by the cable always hold the plug e Dishwasher repairs should only be performed by trained personnel Improper repairs may seriously endanger the user If your dishwasher needs to be repaired you should contact our service centre or your retailer e Never place any solvents in your dishwasher or you may cause an explosion e Do not rest or sit on the open door or the machine could tilt e Before using special dishwasher salt detergent or rinse aid make sure that the manufacturer of these products expressly specifies their use in domestic dishwashers e Always turn off the water tap when your dishwasher is left unattended for any length of time e g when you are away on holiday e Only transport the dishwasher in an upright position Tipping it upside down during transport could cause salty water to leak into the internal compartment and lead to the formation of rust 45 Operating instructions 46 Ud AS Disposing of packaging and old machine Disposing of the packaging Our dishwa
10. mains plug Important The plug must still be accessible after the appliance has been installed In case that the electrical cable has to be replaced please contact your local consumer services department The appliance should not be connected to the electrical supply by means of an extension cable Safety standards require the appliance to be earthed The manufacture accepts no liability for failure to observe the above safety precautions Service If after all these checks the problem persists contact your local consumer services department quoting the model Mod product number PNC and serial number S N This information can be found on the rating plate located on the right hand side of the dishwasher door see picture So that you always have these numbers at hand we recommend you to make a note of them here RAO7 Service and spare parts This product should be serviced by an authorised service engineer and only genuine spare parts should be used Under no circumstances should you attempt to repair the machine yourself Repairs carried out by inexperienced persons may cause injury or serious malfunctioning Contact your local consumer services department Always insist on genuine spare parts 79 A From the Electrolux Group The world s No 1 choice The Electrolux Group is the world s largest producer of powered appliances for kitchen cleaning and outdoor use More tha
11. types of glass can become dull after a e Wooden platters e Items made from synthetic fibres Operating instructions Open the door and slide out the baskets to load the dishes The lower basket The lower basket is designed to take saucepans lids plates salad bowls cutlery etc Serving dishes and large lids should be arranged around the edge of the basket ensuring that the upper spray arm can turn freely The cutlery basket Long bladed knives stored in an upright position are a potential hazard Long and or sharp items of cutlery such as carving knives must be positioned horizontally in the upper basket Take care when loading or unloading sharp items such as knives Cutlery should be placed in the removable cutlery basket with the handles facing downwards If the handles protrude from the bottom of the basket obstructing the lower spray arm load the cutlery with the handles facing upwards Mix spoons with other cutlery to prevent them from sticking together Silver cutlery tends to go black if mixed with steel cutlery Place it in the cutlery basket separate from the others 57 Operating instructions 58 For best results we recommend to use the cutlery grid provided if the size and the dimensions of the cutlery allow it The upper basket The upper basket is desi
12. aste to be sorted into individual types for environmen tally conscious recycling Take your decommissioned machine to your local recycling centre or dealer who will take it back from you for a small handling charge Operating instructions Fe Economical and ecological dishwashing e Only connect the dishwasher to the hot water supply if your hot water is not electrically heated e Ensure that the water softener is correctly adjusted e Do not pre rinse under running water e Select the wash programme to suit the nature and degree of the soiling on the dishes e Do not use more detergent special salt or rinse aid than is recommended in these operating instructions and by the manufacturer of the respective product 47 Operating instructions 48 Description of the appliance and control panel a ur WwW N rPe Upper basket stop Water hardness switch Salt container detergent dispenser type A type B Control panel Rating plate 10 11 1 N Rinse aid dispenser type A type B Filters Lower spray arm Upper spray arm Upper basket Worktop Operating instructions On Off Salt refilling indicator light indicator light 5 vorin A On Off push button Door handle Programme selector Programme guide oial Programme phase indicator Programme sequence indicator As the programme progresses the programme selector dial tur
13. be a hazard 59 Operating instructions 60 Qg Use of detergent Only use detergents specifically designed for use in dishwashers Using no more then the correct amount of detergent contributes to reducing pollution Prior to the start of a wash programme not for the Rinse and Hold programme that does not require the use of detergent The detergent is released during the washing phase Please observe the manufacturer s dosing and storage recommendations as stated on the detergent packaging Fill with detergent Detergent dispenser type A 1 If the lid is closed press release button 1 The lid springs open 2 Fill the detergent dispenser 2 with detergent The marking indicates the dosing levels 20 approximately 20 ml of detergent 30 approximately 30 ml of detergent 3 All programmes with prewash need an additional detergent dose 5 10 g that must be placed in the prewash detergent chamber 3 This detergent will take effect during the prewash phase DE19 4 Close the lid and press until it locks in place Operating instructions Fill with detergent Detergent dispenser type B 1 Open the dispenser by pulling the catch D The lid springs open 2 Fill the detergent dispenser with detergent The marking indicates the dosing levels Min approximately 15 g of detergent Max approximately 30 g of detergent 3 Close the lid and press
14. en the machine is switched on Water hardness Water Use dH TH PPM hardness of german degrees french degrees parts per million setting salt 0 4 0 8 0 80 NO 5 1 9 20 81 200 Level 1 YES 12 22 21 40 201 400 Level 2 YES 23 34 41 60 401 600 Level 3 YES 35 45 61 80 601 800 Level 4 YES 46 50 81 90 801 900 Level 5 YES Operating instructions Setting the water softener 1 Open the dishwasher door 2 Remove the lower basket from the dishwasher 3 Turn the water hardness switch until the required level see table corresponds with the marker 4 Replace the lower basket Filling with salt Special salt can be added in one of two ways e f you are using dishwasher detergent that already integrates the salt function this must be placed in the detergent compartment In this case the water softener must be set to level 1 without putting salt in the salt container e If you are using dishwasher detergent and salt separately the special salt is to be put into the salt container In this case the water softener must be set to between level 1 and 5 depending on the water hardness in your area Only use salt specifically designed for use in dishwashers All other types of salt not specifically designed for use in a dishwasher especially table salt will damage the water softener Only fill with salt just before starting one of the washing programmes except the Rinse and Hold pro
15. fore using your dishwasher for the first time e Check your dishwasher for any transport damage Never connect a damaged machine If your dishwasher is damaged you should contact your supplier e Your dishwasher must be correctly installed and connected Please read the section on Installation to make sure you know all about this e Before using your dishwasher for the first time do not forget that the nominal voltage and current type indicated on the rating plate of your machine must be the same as the nominal voltage and current type at the installation site The necessary electrical fusing is also given on the rating plate Child safety e Packaging parts e g foils styrene foam may be dangerous for children who could even be suffocated You should therefore keep all packaging well away from children e Children may not recognise the dangers of improper use of electrical appliances You should therefore ensure proper supervision during operation and not allow your children to play with your dishwasher e Detergents may have a caustic effect on eyes mouth and throat and may even cause suffocation Keep all detergents in a safe place out of children s reach Operating instructions e The water in your dishwasher should not be used for drinking Detergent residues may still be present in your machine Make sure you do not splash these caustic residues onto your skin or suffocate yourself Keep children well away from your
16. gned for plates dessert plates saucers dinner plates of up to 25 cm in diameter salad bowls cups and glasses Arrange items on and underneath the cup racks so that water can reach all surfaces Glasses with long stems can be placed upside down in the cup rack Light items plastic bowls etc must be loaded in the upper basket and arranged so they do not move 7 N US64 Operating instructions In the case that plates are loaded in the upper basket load them starting from the rear positions of the basket tilting them slightly forwards and avoiding the front positions near the door AAU 1 N Mi uUS71 Before closing the door ensure that the spray arms can rotate freely Adjusting the height of the upper basket If washing very large plates you can load them in the lower basket after moving the upper basket to the higher position Maximum height of the dishes in upper basket lower basket With upper basket raised 20 cm 31 cm With upper basket lowered 25 cm 27 cm To move to the higher position proceed as follows 1 Move the front runner stops A of the upper basket outwards and slide the basket out 2 Refit the basket in the higher position and replace the stops A in their original position After loading your machine always close the door as an open door can
17. gramme This will prevent any grains of salt or salty water which may have been spilt remaining on the bottom of the machine for any period of time which may cause corrosion 51 Operating instructions 52 To fill 1 Open the door remove the lower basket and unscrew the cap of the salt container by turning it anticlockwise 2 Pour 1 litre of water inside the container this is necessary only before filling with salt for the first time 3 Using the funnel provided pour in the salt until the container is full 4 Replace the cap making sure that there is no trace of salt on the screw thread or on the gasket 5 Screw on the cap tightly turning it clockwise until it stops with a click SR14 The salt container will require topping up periodically You are reminded of this by the salt indicator light on the control panel which will illuminate when the salt has finished The salt indicator light on the control panel can remain illuminated for 2 6 hours after the salt has been replenished assuming the dishwasher remains switched on If you are using salts that take longer to dissolve then this can take longer The function of the machine is not affected Do not worry if water over flows from the unit when filling with salt this is quite normal Operating instructions Rinse aid Rinse aid is automatically added during the last rinse ensuring thorough rinsing and spot and streak free dr
18. he dishwasher is unplugged and the water tap turned off Operating instructions Maintenance and cleaning AN Clean the external surfaces of the machine and control panel with a damp soft cloth If necessary use only neutral detergents Never use abrasive products scouring pads or solvent acetone trichloroethylene etc Ensure that the seals around the door the detergent and rinse aid dispensers are cleaned regularly with a damp cloth We recommend every 3 monthsto run a 65 C wash programme without dishes using detergent Cleaning the filters The filters in the base of the washing compartment are to a large extent self cleaning Nevertheless the filters should be checked and cleaned from time to time Dirty filters will degrade the washing result 1 Open the door remove the lower basket 2 The dishwasher filter system comprises a coarse A a microfilter C and a flat filter D Unlock the filter system using the handle on the microfilter and remove 3 Turn the handle about s a turn anticlockwise and remove ea 4 Take hold of the coarse filter A by the handle with the hole and remove from the microfilter C hee 5 Clean all filters thoroughly under running water 6 Remove the flat filter D from the base of the washing compartment and clean both faces thoroughly 67 Operating instructions 68 7 Put the flat filter
19. n 55 million Electrolux Group products such as refrigerators cookers vacuum cleaners chain saws and lawn mowers are sold each year to a value of approx 14 billion USD in more than 150 countries around the world AEG Hausgerate GmbH Postfach 1036 D 90327 Nurnberg http www aeg hausgeraete de Copyright by AEG Technische Anderungen vorbehalten Subject to change without notice CD 152969 94 0
20. nnection Clean out the siphon Check the water drain hose connection Close the door Insert the mains plug Replace the fuse use a different brand of detergent Once the checks have been carried out press the On Off push button the programme will continue from the point in which it was interrupted If the malfunction reappears contact your local service force centre Operating instructions the wash results are not satisfactory The dishes are not clean e The wrong washing programme has been selected e The dishes were arranged in such a way asto stop water reaching all parts of the surface The baskets must not be overloaded e The spray arms do not rotate freely dueto wrong arrangement of the load e Thefilters in the base of the washing compartment are dirty or incorrectly positioned e Too little or no detergent has been used e Where there are limescales deposits on the dishes the salt container is empty or the wrong level of the water softener has been selected e The drain hose connection is not correct e The salt container cap is not properly closed The dishes are wet and dull e Rinse aid was not used e The rinse aid dispenser is empty There are streaks milky spots or a bluish coating on glasses and dishes e Decrease rinse aid dosing Water drops have dried onto glasses and dishes e Increase rinse aid dosing e The detergent may be the cause Contact the detergent manufacturer s
21. ns to show the phase in the wash programme the appliance has reached 49 Operating instructions 50 Prior to using for the first time i Before using your dishwasher for the first time 1 Ensure that the electrical and water connections comply with the installation instructions 2 Remove all packaging from inside the appliance 3 Set the water softener 4 Pour 1 litre of water inside the salt container and then fill with salt 5 Fill the rinse aid dispenser 6 Run a Rinse and Hold programme The water softener The dishwasher is equipped with a water softener designed to remove minerals and salts from the water supply which would have a detrimental or adverse effect on the operation of the appliance The higher the content of these salts the harder your water is Water hardness is measured in equivalent scales German degrees French degrees and PPM parts per Million The softener should be adjusted according to the hardness of the water in your area Your local Water Authority can advise you on the hardness of the water in your area The dishwasher is factory set at position 2 If your water is below level 1 it is already soft and therefore there is no need to use salt In this case adjust the water softener on level 1 without using salt If the water softener has been adjusted on level 1 and no salt is being used the salt refilling indicator light on the control panel will always remain illuminated wh
22. ramme suitable for the cutlery and dishes Start the wash programme Loading cutlery and dishes Sponges household cloths and any object that can absorb water may not be washed in the dishwasher e Before loading the dishes you should Remove large left overs Soften remnants of burnt food in pans e When loading the dishes and cutlery please note Dishes and cutlery must not impede the rotation of the spray arms Load hollow items such as cups glasses pans etc with the opening downwards so that water cannot collect in the container or a deep base Dishes and items of cutlery must not lie inside one another or cover each other To avoid damage to glasses they must not touch Lay small objects in the cutlery basket For washing in the dishwasher the following cutlery dishes are not suitable are of limited suitability e Cutlery with wooden horn china or Only wash stoneware in the dishwasher if it mother of pearl handles is specifically marked as being dishwasher e Plastic items that are not heat safe by the manufacturer resistant e Glazed patterns may fade if machine e Older cutlery with glued parts that is Washed frequently not temperature resistant Silver and aluminium parts have a tendency Bonded cutlery items or dishes to discolour during washing Left overs e g e Pewter or copper items egg Sala egg yolk and De piren cause discolouring and staining on silver olee gal use e Some
23. s appliance should be carried out by a qualified electrician and or plumber or competent person Remove all packaging before positioning the machine If possible position the machine next to a water tap and a drain Fitting under a counter kitchen worktop or sink By removing the machine s worktop you can install it under a close fitting sink unit or a pre existing top providing the dimensions of the recess correspond to those shown in the picture Proceed as follows Remove the machine s worktop by unscrewing the two rear retaining screws pull from the front and slide out the rear slots lifting the worktop Insert the machine after adjusting height and levelling with the adjustable feet When inserting the machine ensure that the INOS water inlet and drain hoses are not kinked or squashed If the dishwasher is later used as a free standing appliance the original worktop must be re mounted The plinth on free standing appliances is not adjustable Levelling Good levelling is essential for correct closure and sealing of the door When the appliance is correctly levelled the door will not catch on either side of the cabinet If the door does not close correctly loosen or tighten the adjustable feet until the machine is perfectly level AN Installation instructions Water supply connections This dishwasher may be fed with either hot max 60 or cold water Nevertheless we advise you
24. shers require effective protective packaging in transit though we always confine ourselves to what is absolutely necessary Warning Packaging parts e g foils styrene foam may be dangerous for children who could even be suffocated You should therefore keep all packaging well away from children All packaging materials used are environmentally compatible and reusable The cardboard parts are produced from recycled paper and the wood is untreated The plastics are marked as follows gt PE lt for polyethylene e g packaging foils gt PS lt for polystyrene e g padding essentially CFC Free gt POM lt for polyoxymethylene e g plastic clamps Give the packaging for reuse to your local recycling centre Your municipal or local authority will give you its address Disposing of your old machine When your machine finally reaches the end of its life and you withdraw it from service you should render it unserviceable before having it disposed of Warning Children at play could lock themselves in your machine and suffocate or otherwise endanger their lives Therefore pull out the main plug and detach and discard the electrical supply lead Disable the door lock so that the door no longer closes Marking of plastic parts for graded recycling all plastic parts in your machine are marked with internationally standardised abbreviations e g lt PS gt for polystyrene When your machine is disposed of this en ables plastic w
25. sing of packaging and old machine Economical and ecological dishwashing Description of the appliance and control panel Prior to using for the first time The water softener Filling with salt Rinse aid In daily use Loading cutlery and dishes The lower basket The cutlery basket The upper basket Adjusting the height of the upper basket Use of detergent Detergent tablets Concentrated detergent Use of 3 in 1 combi detergent tablets Washing programmes Starting a washing programme Unloading the dishwasher Maintenance and cleaning Cleaning the filters What to do when Technical specifications Hints for test centres Fitting under a counter Levelling Water supply connections Water inlet hose with safety valve Water outlet hose connection Electrical connection Contents 43 Operating instructions Safety instructions The safety of AEG electrical appliances conforms to accepted rules of technology and the Appliance Safety Act We as manufacturers however see ourselves as being obliged to familiarise you with the following safety instructions Using your dishwasher for its intended purpose e Only use your dishwasher for machine washing of household crockery If your machine is misused or used for any purposes other than that for which it is intended the manufacturer cannot be held liable for any damage caused e For safety reasons you should not convert or modify your dishwasher in any way Be
26. siphon back into the machine If you use a drain hose extension it must be no longer than 2 metres and its internal diameter must be no smaller than the diameter of the hose provided i 1 5 ge max 100 cm min 30 cm pe Er 2mmax san SS Likewise the internal diameter of the couplings used for connections to the waste outlet must be no smaller than the diameter of the hose provided Attention Our appliances are supplied with a security device to protect against the return of dirty water back into the machine If the spigot of your sink has a no return valve incorporated this can prevent the correct draining of your dishwasher We advise you therefore to remove it 17 Installation instructions 78 Electrical connection Information concerning the electrical connection is given on the rating plate on the edge of the dishwasher s door on the right Before plugging the appliance into the wall socket make sure that 1 The mains voltage and current rating at the site of installation match the nominal voltage and current rating given on the rating plate 2 The meter fuses mains power supply and wall socket can all take the maximum load required Make sure that the socket and plug are compatible without having to use any type of adaptor If necessary have the domestic wiring system socket replaced To isolate the dishwasher from mains remove the
27. tically 5 To interrupt a washing programme in progress Interrupt change or cancel a washing programme in progress ONLY if it s absolutely necessary Attention Hot steam may escape when the door is opened There is risk of scalding Open the door carefully e Open the dishwasher door the programme will stop Close the door the programme will start from the point in which it was interrupted e Pressing the On Off in this case the On Off indicator light turns off Press the On Off push button again the programme will start from the point in which it was interrupted 6 End of the washing programme The dishwasher will automatically stop Switch off the dishwasher by pressing the On Off push button On Off indicator light turns off Hot steam may escape from the appliance when opening the door immediately after the end of the programme therefore open the door carefully 65 Operating instructions 66 AN Unloading the dishwasher Hot dishes are sensitive to knocks The dishes should therefore be allowed to cool down before removing from the appliance Leave the dishes in the dishwasher for approx 15 minutes with the door ajar after the end of programme so that they dry better and will be cooler Empty the lower basket first and then the upper one this will avoid water dripping from the upper basket onto the dishes in the lower one When the washing programme has finished it is recommended that t
28. tor dial Programme Prewash Main wash Main wash Cold rinse sequence Main wash Cold rinse Hot rinse Cold rinse Hot rinse Hot rinse Drying Drying Consumption B Y Y Y Y Duration 110 120 min 95 105 min 30 40 min 12 min Energy 1 15 1 24kWh 1 15 1 24kWh 1 05 1 15 kWh 0 1 kWh Water 16 18 litres 13 15 litres 11 13 litres 10 litres 1 Testing programme for EN 50242 see Hints for test centres 2 Ideal for washing crockery and cutlery of breakfast and dinner fresh soil The time value is approximate and depends on the pressure and the temperature of the water and also by the variations of the power supply This is a perfect daily programme made to meet the needs of a family of 4 persons who only wish to load breakfast and dinner crockery and cutlery 3 The consumptions values are intended as a guide and depends on the pressure and the temperature of the water and also by the variations of the power supply 64 AN AN IN Operating instructions Starting a washing programme 1 Check that the baskets have been loaded correctly and that the spray arms can rotate freely 2 Turn on the water tap 3 Close the dishwasher door 4 Setting and starting the programme Turn the programme selector dial clockwise until the programme marker on the knob corresponds with the letter of the programme you wish to select Press the On Off push button the On Off indicator light will come on and the machine will start automa
29. until it locks in place 4 All programmes with prewash need an additional detergent dose 5 10 g that must be placed over the lid of the dispenser This detergent will take effect during the prewash phase 61 Operating instructions 62 Detergent tablets Detergent tablets of different brands dissolve at different speeds For this reason some detergent tablets cannot develop their full cleaning power during short programmes Therefore please use normal programmes with prewash when using detergent tablets Do not place the tablets in the tub or in the cutlery basket as this will result in poorer wash results The tablets should be placed in the detergent dispenser Concentrated detergent Based on their chemical composition dishwasher detergents can be split into two basic types conventional alkaline detergents with caustic components low alkaline concentrated detergents with natural enzymes The use of 50 C washing programmes in conjunction with concentrated detergents reduces pollution and is good for your dishes these wash programmes are specially matched to the dirt dissolving properties of the enzymes in the concentrated detergent For this reason 50 C wash programmes in which concentrated detergents are used can achieve the same results that can otherwise only be achieved using 65 C programmes Operating instructions Use of 3 in 1 combi detergent tablets General
30. ying The dispenser which is positioned inside the door holds about 110 ml of rinse aid which is sufficient for 16 40 dishwashing programmes depending upon the dosage setting Rinse aid can be added in one of two ways e f you are using dishwasher detergent that already integrates the rinse aid function this must be placed in the detergent compartment In this case the rinse aid compartment must be empty If in the rinse aid dispenser there is still rinse aid you must wait until it has finished before using detergent that contains rinse aid e f you are using dishwasher detergent and rinse aid separately the rinse aid is to be put into the rinse aid dispenser In this case the rinse aid dosage must be set in position from 1 to 6 see Adjusting the dose Filling with rinse aid Rinse aid dispenser type A 1 Open the container by pressing the release button A 2 Fill with rinse aid exactly up to the level indicator marked max FT i a Ensure that the lid is closed after every refill 53 Operating instructions 54 Top up with rinse aid when the indicator B becomes clear Adjusting the dose According to the finish and drying results obtained adjust the dose of rinse aid by means of the 6 position selector position 1 minimum dosage position 6 maximum dosage Increase the dose if there are drops of water or lime spots on the dishes after washing
Download Pdf Manuals
Related Search