AEG FAVORIT 88050 I User's Manual
Contents
1. Exception hardness setting 1 follows hardness setting 10 When the hardness setting is correct press the ON OFF button The hardness setting is now saved 13 Operating Instructions Special salt for the water softener H IS 1 If the water hardness in your area is less than 4 d then the water in your dishwasher does not need to be softened and you do not need to use special salt or salt substitute Water can be softened in one of two ways e f you are using dishwasher detergent that already contains salt sub stitute the detergent only is put into the detergent compartment In this case the water softener must manually be set to O and electronically to 1 to ensure that no special salt is added e f you are using dishwasher detergent and special salt separately the special salt is to be put into the salt supply container In this case the water softener must manually be set to 0 and electronically to between 2 and 10 depending on the water hardness in your area to ensure that the special salt is taken from the detergent container only Use only special salt intended for dishwashers Never fill the salt supply container with different types of salt e g cooking salt or detergent This would destroy the water softener Prior to filling with salt please check each time that you really do have a packet of special salt in your hand Setting the amount of special salt to be added Some a2. 3 9 T 5 5L 26 32 4 HL 19 25 ll 0 3 3L 0 7 1 8 ull 2 eu 1 under 0 7 no salt iL necessary 1 d German degree measure of the hardness of water 2 mmol l millimol per litre international unit for the hardness of water 3 On this setting the length of the dishwashing cycle may be slightly longer Factory setting Operating Instructions Open the dishwasher door Remove the lower rack from the dis Turn the hardness range switch to 0 Replace the lower rack Press the ON OFF button Set water softener Using the table as a guide adjust the water softener to that which cor responds to the hardness of the water in your area The dishwasher must be switched off Manual setting hwasher or 1 see table Electronic setting The LED in the ON OFF button will become illuminated If other indicators are also illuminated this means that a dishwashing cycle has been activated The dishwashing cycle must be cancelled RESET Press function buttons 1 and 2 simultaneously for approx 2 seconds All other indicators will go out Press the function buttons 1 and 2 simultaneously and keep them pres sed The LED indicators in function buttons 1 to 3 will flash Press function button 1again The LED indicator for function button 1 will flash The multi display will indicate the hardness setting Pressing function button 1 increases the hardness setting by 1 degree
3. 89 336 EWG dated 03 05 1989 including Directive Amendment 92 31 EWG EMC Directive 40 Operating Instructions Notes for Test Institutes Testing in accordance with EN 60704 must be carried out with the appliance fully loaded and using the test programme see Programme Table Tests in accordance with EN 50242 must be carried out when the salt dispenser and rinse aid container have been filled with salt and rinse aid respectively and using the test programme see Programme Table Full Load 12 place settings incl serving dishes Detergent Dosing 5g 25g Type B Rinse Aid Setting 4 Type III Sample loading arrangements Upper basket without cutlery tray fV ij NNN We La N AN iq a e e If necessary move the cup rest from right to cup rest is at the same height Half Load 6 place settings incl serving dishes leaving alternate positions free 20g Type B 4 Type III Upper basket with cutlery tray O eft When doing this ensure that the 41 Operating Instructions 42 Lower basket with cutlery basket Cutlery basket l AN AAA Installation and Connection Instructions
4. 19 Daly Us SEERE DANSEDE ces 20 Loading cutlery and dishes 00 cece cece eee 20 Loading Cutlery 2 0 0 eee eee I 21 Loading Pans Frying Pans and Large Plates 23 Loading Cups Glasses and Coffee Services 20000000000 25 Adjusting the Height of the Upper Basket 0005 26 Filling with Detergent iiri ers ds ar ye a aes 27 Use of 3 in 1 Combi Detergent Tablets 28 Concentrated Detergent perira lars eects 29 Detergent tablets pia bep etc io a IER ls 29 Automatic Wash Programmes ssssseee 29 Selecting the Wash Programme Programme Table 30 Starting a dishwashing cycle 6 cece eee eee eet eens 32 Changing interrupting aborting a dishwashing cycle 32 Setting or changing the start delay 200000 cee eee eae 33 Load Sensing Sensor Logic ccc eee eee eee eens 34 Switching Off the Dishwasher lesser 35 Emptying the Dishwasher 0 0 cece eee ees 35 Contents Care and Cleaning xico an p LR ER Ex eb e RR 35 Cleaning the FILER iui deiecti Dette Pee rea Er jasa 36 What to do when tai Be eee el E RENE 37 Error messages are displayed 0 cc cece eee ee eee 37 there are problems with the operation of the dishwasher 39 the wash result is not satisfactory 6 0 cece eee eee eee ee 39 Technical Data secs eb Someta as ais ee Iu
5. Changing interrupting aborting a dishwashing cycle Only change or interrupt a dishwashing cycle that is in progress if it is absolutely necessary After the appliance has been closed again the air that has entered will be heated significantly and expand As a result water may collect in the base of the appliance and trigger the anti flood system Changing a dishwashing cycle If you would like to change the dishwashing cycle in the first 3 seconds after having selected a cycle briefly press the button for the new dish washing cycle If you would like to change the dishwashing cycle after this time pro ceed as follows Press the button for the new dishwashing cycle and hold it down The indicator for the dishwashing cycle that is currently running will flash After several seconds only the indicator for the new dishwashing cycle will be flashing Release the cycle button The newly selected dishwashing cycle will begin Operating Instructions I 1 IS 1 Continue pressing the DELAY TIMER button until the number of Interrupting the dishwashing cycle by opening the dishwasher door Hot steam may escape when the door is opened There is a risk of scal ding Open the door carefully Open the door of the dishwasher The dishwashing cycle will stop Close the door The dishwashing cycle will continue Aborting the dishwashing cycle RESET Press the function buttons 1 and 2 simultaneously and k
6. INSTALLATION AND CONNECTION INSTRUCTIONS Installing the Dishwasher e The dishwasher must be installed on a firm floor and adjusted to ensure that it is stable and level e To compensate for unevenness in the floor and to match the height of the appliance to that of surrounding units extend the threaded feet by uns crewing use a screwdriver id weer 2 2 SS For built in integrated and fully integrated dishwashers the rear feet should be adjusted from the front of the appliance using a screwdriver e The drain hose inlet hose and mains cable must not be kinked or crushed when the dishwasher is in position e The dishwasher must also be screwed on tightly to the work surface or to the adjoining units This is essential to ensure the dishwasher does not tip 43 Installation and Connection Instructions 44 Dishwashers That Can Be Integrated see installation template supplied The door of the appliance can be fitted with a wooden furniture door with the following dimensions Width 591 594 mm Thickness 16 24mm Height dependenton Recess height variable Plinth height The adjustment so that the unit matches the height of the adjoining units The exact height of the adjoining units must be measured at the place of installation Weight max 8 kg Installation and Connection Instructions Connecting the Dishwasher Water Connection a pe The dishwasher is
7. Operating Instructions R IS 1 place forks and spoons in the grid For larger items of cutlery e g a To avoid damage to glasses they must not touch Do not lay small objects e g lids in the cutlery rack Loading Cutlery Long pointed items of cutlery are a hazard if placed in the cutlery basket particularly to children see Safety Instructions They should therefore be placed in the upper rack Place knives small spoons and small forks in the cutlery tray Place forks and spoons that do not fit in the cutlery tray in the cutlery basket To ensure that all items of cutlery in the cutlery basket are properly was hed you should place the grid insert on the cutlery rack insert on the cutlery basket with the handle downwards whisk half of the top for the cutlery basket can be left off S ZR i COMIN NA DO SOON pol iS CO Mia gol OONA oo Om gg LJCIETINQS SN SENE KERA E sas Y 4995 21 Operating Instructions 22 AN is 1 C2 On some models of dishwasher it is possible to open the cutlery basket To ensure that the cutlery basket cannot open on removal from the appliance you should always hold both parts of the two part handle Place the cutlery baske
8. These products should be strictly used according to the detergent manufacturers instructions Do not place the tablets in the tub or the cutlery basket as this will result in poorer wash results The tablets should be placed in the detergent doser If you encounter problems when using 3 in1 products for the first time then please contact the detergent manufacturers care line the telephone number is given on the product packaging Special Advice When using combination products the rinse aid and salt lights are no longer useful It may be helpful therefore to switch the rinse aid off please note that only some dishwashers have this facility and selec ting the lowest possible setting for water hardness For more information please refer to your instruction manual If you decide to switch to the use of a standard detergent system we advise that you e Refill both the salt and rinse aid compartments Switch the waterhardness setting to the highest possible position and run for three normal cycles without a load Readjust the waterhardness setting again according to the conditions for your region as per the instruction manual Operating Instructions Concentrated Detergent Based on their chemical composition dishwasher detergents can be split into two basic types conventional alkaline detergents with caustic components low alkaline concentrated detergents with natural enzymes The use of 50 C was
9. be heard the WAY indica tor is continuously illumina ted The Y indicator is conti nuously illuminated The e indicator is conti nuously illuminated After remedying the After rectifying an Possible cause The leak prevention system has been triggered The middle spray arm is jammed The door of the dishwasher is open The indicator e is only intended to remind you to occasionally check the dish washer s filter and to clean it out when necessary It becomes illuminated at regular intervals regardless of the state of cleanliness of the filter Remedy Turn off the tap and contact customer ser vice Open the door care fully Hot steam may escape when the door is opened There is a risk of scalding Arrange the dishes and cutlery in the racks so that the spray arm above can rotate freely Close the dishwa sher door Close the dishwasher door The indicator goes out automatically at the start of the next dish washing cycle ww yor amp error shut the door iB or 20 error press the button for the dishwa shing cycle that has been started The dishwashing cycle will continue If the fault is displayed again please contact customer service For all other errors displayed please contact customer service stating the error code See chapter Customer Service Operating Instructions there are problems with the operation of the dish washer Malfunction The pro
10. crushed or entangled e Connecting the drain hose Maximum permitted height 1 metre Minimum required height 40 cm above the lower edge of the machine Extension hoses e Extension hoses are available from your dealer or customer service The internal diameter of the exten sion hoses must be 19 mm to ensure that the function of the appliance is not impeded e Extension hoses may be laid a maximum of 3 metres horizontally p the maximum permitted height for amp EI E the connection for the drain hose is a soom then 85 cm 85 cm gt 40 cm Sink outlet connection e The outlet of the drain hose 19 mm fits all commonly available sink outlet spigot types The outer diameter of the spigot connection must be at least 15 mm e The drain hose must be fixed to the sink outlet connection using the hose clamp supplied If the dishwasher is fitted at a high position If the dishwasher is installed at a high level and the drainhose connec tion is less than 30 cm from the bottom of the appliance adapter kit ET 111099520 must be fitted This is available from Customer Service Water drain into wash basins only possible with free standing appliances In the case that you wish to hang the drain hose in a wash basin use a detachable hose elbow You can obtain this from AEG customer service under spare part number ET 646 069 190 Fit the elbow to the drain hose Secure the drain h
11. Terlaton Street 42 44 1011 Riga Tel 371 2 297821 Fax 371 2 821286 Lthuania Electrolux Lthuania Verkui 29 2600 Vilnus Tel 372 272 3326 Fax 372 272 3366 Malaysia Arzbergh Engineering Poland Electrolux Poland Sp zo o ul Domaniewska 41 02 034 Warszawa tel 022 874 33 33 fax 022 874 33 00 Russia Electrolux Russia Ltd 16 Olympiysky prospekt 129090 Moscow Tel 095 937 7837 Fax 095 926 5513 Saudi Arabia Alia Trading Corporation No 49A B Jalan Petaling Utama P O Box 4101 7 4600 Petaling Jaya Tel 3 795 1084 Fax 3 795 1082 Singapore Arzbergh Engineering 19 Tanglin Road 06 07 Singapore 247909 Tel 65 7356572 Fax 7351124 Slovakia Rep Electrolux Slovakia S R O Seberiniho 1 821 03 Bratislava Tel 02 4333 4322 4355 Fax 02 4333 6976 USA ANDI Co Appl Inc East 65 Campus Plaza Edison New Jersey 0837 USA Tel 201 2258839 King Abdul Aziz Street Riyadh Tel 4645977 Al Nahas Est Musaidia Market P O Box 1 15 29 Jeddah Tel 6606852 Slovenia Electrolux Slovenia D 0 0 Traska UI 132 1000 Ljubljana Tel 61 1234 137 Fax 61 1234 238 South Africa AEG Pty Ltd 55 12th Road P O Box 1 02 64 Kew Johannesburg 2000 Tel 8069111 Syria Masri amp Shami P O Box 24 96 Damascus Tel 214080 51 Guarantee Conditions 52 GUARANTEE CONDITIONS Weitere Kundendienststellen im Ausland In diesen L ndern gelten die Garanti
12. in the base of the washing compartment are to a large extent self cleaning Nevertheless the filters should be checked and cleaned from time to time Dirty filters will degrade the washing result Open the door remove the lower rack ses a coarse fine filter microfilter and a flat filter Unlock the filter system using the handle on the microfilter and remove clockwise and remove 2 by the handle with the hole and remove from the microfilter 3 running water base of the washing compartment and clean both faces thoroughly the washing compartment microfilter and press together and lock by turning the handle clock wise to the stop During this process ensure that the flat filter does not protrude above the base of the washing compartment Under no circumstances may the dis hwasher be used without filters Operating Instructions What to do when Try to rectify minor faults on the dishwasher with the aid of the instructions given here If you call in customer service to resolve one of the malfunctions listed here or rectify an error made in the operation of the appliance the customer service engineer s visit is not free of charge even during the period of guarantee Error messages are displayed If any of the indicators in the control panel as listed in the table below are flashing or are illuminated you can probably rectify the fault yourself Malfunction One con
13. your dealer who will for a small contribution to the costs dispose of it for you Operating Instructions Economical and Ecological Dishwashing Only connect the dishwasher to the hot water supply if your hot water is not electrically heated e Ensure that the water softener is correctly adjusted Do not pre rinse dishes under running water f you wash a small load the load sensor calculates the amount of water necessary and shortens the programme It is more economical to always wash with a full load e Select the wash programme to suit the nature and degree of the soil ing on the dishes Do not use more detergent special salt or rinse aid than is recom mended in these operating instructions and by the manufacturer of the respective product e The dishwasher s interior light is always switched on as long as the door of the appliance is open To save energy you should therefore always close the door of the dishwasher after loading or removing dishes Operating Instructions Appliance Features and Control Panel Top Spray Arm Rubber Seal for Connecting the Water Feed to the Spray Arm Spray Arms Water hardness switch Container for Special Salt Container for Detergent Container for Rinse Aid Operating Instructions Control Panel Function Bu
14. 0 the length of the dishwashing cycle may be slightly longer 30 e normally soiled e dried leftovers NORMAL V 65 Pre Wash Main Wash Rinsing Final Rinse Drying y 90 100 minutes 1 15 1 35 kWh 17 19 litres Operating Instructions Dinner Service and Dessart Dishes All Type of Dishes i and Coffee Types of Dis Cooking Utensils Service hes In Addition with with non temperature resistant dishes delicate glasses Type of normally soiled lightly Used dishes Soiling soiled that are collec ted in the dish washer and are to be washed at a later point in particularly suitable when concentrated detergents are used time Suitable NORMAL ENERGY SAVING GLAS PRE WASH Wash Programme Ev ce 50 12 v y Programme Pre Wash Pre Wash Pre Wash Sequence Main Wash Main Wash Main Wash Rinsing Rinsing 2x Rinsing Final Rinse Final Rinse Final Rinse Drying Drying Drying Consumption ASA y y y y Figures Duration 85 95 minutes 130 150 minutes 37 minutes 12 minutes Energy 1 10 1 20 kWh 0 95 1 05 kWh 0 7 kWh lt 0 1 kWh Water 15 17 litres 12 14 litres 12 litres 4 litres 1 Test programme for test institutes 2 The Ce so wash programme washes normally soiled dishes with a very low electricity con sumption If the dishes need to be washed more quickly as an alternative you can use the Ts wash programme 3 Noise levels vary at different stages of the wash progra
15. Assaferi P O Box 539 Tripoli Malta ITC International Trading Com pany White House Building Mountbatte Street Blata L Bajda Tel 220644 Mauritius Happy World Centre Ltd P O 7 54 1 Chausee Street Port Louis Tel 25355 Namibia AEG NAMIBIA PTY LIMITED Jeppe Street Northern Industrial Area Windhoek Tel 061 21 6082 4 Fax 061 217838 New Zealand Euro Life New Zealand Ltd Privat Bag 58 Symonds Street Auckland Tel 09 525 2222 Nouvelle Caledonie Socometra N C B P 483 Nouman Tel 275444 Oman Moshin Haider Darwish P O Box 1 35 Muscat Tel 703743 Service Departments Estonia Electrolux Estonia Ltd Mustam e tee 24 EEO006 Tallinn Tel 372 6 650 090 Fax 372 6 650 092 Hongkong Wo Kee Services Ltd 585 609 Castle Peak Road Kwai Chung N T Hongkong Tel 2494 4000 Israel Electricity amp Electronic Services Evis LTD 19 Hataasia st Raanana Industrial area 43654 Tel 972 9 7448118 Fax 972 9 7603618 e mail evis evis co il Japan Electrolux Japan Ltd Domestic Appliances Department Maruzen Showa Warehouse Building Tookai 4 5 12 Ota ku 143 006 Tokyo Tel 0120 13 7117 Fax 03 3790 5257 Thailand OLYMPIA Thai Ltd 44 Ratchadapisek Road 10320 Bangkok Tel 2 513 6111 Fax 2 513 2574 Hungary Electrolux Lehel KFT AEG Div Erzs bet Kir lyn tja 87 1142 Budapest Tel 00361 467 3200 Latavia Electrolux Latavia Ltd
16. Centres section In this respect please read the Service note on the rear of these user instructions Your dishwasher is fitted with the new PULSE WASH wash system With this wash system the motor speed and spray pressure are varied during the wash programme to improve the cleaning of the dishes It is for this reason that the noise level changes during the wash programme Printed on paper manufactured with environmentally sound processes He who thinks ecologically acts accordingly Contents CONTENTS Operating Instructions 5 Safety Instructions sisii ia Er eens 5 Disposal sucias ii RA eee Lea oan EASE we OS 7 Economical and Ecological Dishwashing 8 Appliance Features and Control Panel 9 Control Panel i n e A heehee edad heed 10 Prior to using for the first time 0 0 cee eee eee 11 Water softener ees o eerie ee ex PE e EE d 12 Set water softener 00 cece eee eee eee 13 Special salt for the water softener 00 0c eee eee eee eee 14 Setting the amount of special salt to be added 14 Adding special salt 15 RINSEAID s eve ERE UE es 16 Activating deactivating the inflow of rinse aid 16 Adding rinse aid acca ar ee ee e eee xe 17 Adjusting Rinse Aid Dosing 0 cece cece eens 18 Activating deactivating the acoustic signal
17. FAVORIT 88050 i Dishwasher User Instructions AEG O10 wO O Oe E O wel 0O Ge 8 je m0 10 80 Re f Dear customer Please read these user instructions carefully Above all please observe the safety instructions on the first few pages ofthese user instructions Please keep these user instructions for later reference Pass them on to any subsequent owner of the appliance The warning triangle and or specific words Warning Caution Important are used to highlight instructions that are important for your safety or for the function of the appliance It is imperative that these instructions are observed This symbol or numbered instruction steps lead you step for step through the operation of the appliance Next to this symbol you receive additional information and practical tips on using the appliance Tips and instructions for the economical and environmentally conscious use of the appliance are marked with a clover leaf In the event of a malfunction these operating instructions contain information on how to rectify faults yourself see the What to do if section If these instructions are insufficient please contact your nearest custo mer service centre In the case of technical problems our customer service organisation is available to provide you with assistance at any time you will find addresses and telephone numbers in the Customer Service
18. Pressing function button 2 will change the setting Once the multi display is indicating the required setting press the ON OFF button The setting is now saved Adding rinse aid If you are using dishwasher detergent and rinse aid separately add the rinse aid Prior to using the dishwasher for the first time When the RINSE AID indicator 3X on the control panel is illumina ted The rinse aid compartment is on the inside of the dishwasher door release button with your finger lid 17 Operating Instructions 4 Fill with rinse aid exactly up to the level marked max this corresponds to a quantity of approx 140 ml 5 Close the lid and press until it locks into place 6 Wipe up any spilt rinse aid with a cloth Otherwise too much foam will be formed during the wash Adjusting Rinse Aid Dosing i As the dishes are washed rinse aid is released from the dispenser into the wash water The dose is factory set at 4 and can be adjusted from 1 to 6 Only change the setting if streaks milky spots or dried on water marks are visible on glasses or crockery t 1 Open the door of the dishwasher 2 Press the rinse aid compartment release button with your finger 3 Fully open the rinse aid compartment lid 4 Set the dose level 5 Close the lid and press until it locks into place 6 If rinse aid has run out wipe up with a cloth Operat
19. be washed in the dishwasher For washing in the dishwasher the following cutlery dishes are not suitable Cutlery with wooden horn china or mother of pearl handles Plastic items that are not heat resi stant Older cutlery with cement that is not temperature resistant Bonded cutlery items or dishes Pewter or copper items Lead crystal glass Steel items subject to rusting Wooden platters Items made from synthetic fibres are of limited suitability Only wash stoneware in the dishwasher if it is specifically marked as being dishwasher safe by the manufacturer Glazed patterns may fade if machine was hed frequently Silver and aluminium parts have a tendency to discolour during washing Left overs e g egg white egg yolk and mustard often cause discolouring and staining on silver Therefore always clean left overs from silver immediately if it is not to be washed straight after use Some types of glass can become dull after a large number of washes Before loading the dishes you should Remove large left overs Soften remnants of burnt food in pans When loading the dishes and cutlery please note Dishes and cutlery must not impede the rotation of the spray arms Load hollow items such as cups glasses pans etc with the opening downwards so that water cannot collect in the container or a deep base Dishes and items of cutlery must not lie inside one another or cover each other
20. d out by qualified ser vice engineers Improper repairs can give rise to significant hazards for the user If your appliance needs repairing please contact custo mer service or your dealer e Never place the dishwasher in operation if the mains cable water inlet or drain hose is damaged or the control panel work top or plinth area is damaged such that the inside of the appliance is freely accessible e f the mains lead is damaged or is to be replaced for a longer lead the cable obtainable from AEG customer service must be changed by a service engineer authorised by AEG e Never unplug the appliance by pulling on the cable always pull the plug e Additions or modifications to the dishwasher are not permitted for safety reasons e Ensure that the door of the dishwasher is always closed when it is not being loaded or unloaded In this way you will avoid anybody tripping over the open door and hurting themselves e Sharp knives and items of cutlery with sharp edges must be placed in the cutlery tray or in the upper rack Correct Use e Only wash household dishes using the dishwasher If the appliance is used for other purposes or is used incorrectly the manufacturer cannot accept any liability for any damage caused Prior to use ensure that the manufacturers of the special salt deter gent and rinse aid employed specifically permit the usage of their products in household dishwashers Do not put any solvents in the dis
21. eae eee 40 Notes for Test Institutes sssuesssee RR 41 Installation and Connection Instructions 43 Installing the Dishwasher sseleeeeennnnennnn 43 Dishwashers That Can Be Integrated 002000 cee eee eee 44 Connecting the Dishwasher 00 0 cece eee eens 45 Water Connection s eiua eru pasa sawtaurd ne ak REA CIERRE 45 Permitted water pressure 2 cece eee 45 Connect the inlet hose oo cece eee eee 45 Watekdrall e eise attente ene Md aba ae hanes 47 Leak prevention system 1 0 eee eee ees 48 Electrical connection 1 0 0 0 cc ee eee eee 48 CONNECTIONS xaxa Beg dew adhe a T a aA eee 49 Service Departments co cirios Io 50 Guarantee Conditions eee 52 Service a eeu eatin rele sie 55 Operating Instructions OPERATING INSTRUCTIONS Safety Instructions The safety aspects of AEG electrical appliances comply with accepted technical standards and the German Appliance Safety Law Neverthe less as a manufacturer we consider it our obligation to make you aware of the following safety information Installation Connection and Placing into Operation e The dishwasher may only be transported upright e Check the dishwasher for transport damage Do not in any circum stances connect an appliance that is damaged In the case of damage please contact your supplier Prior to placing the appliance in operation ensure that
22. ease the loading of large items the two rear plate inserts in the lower rack can be folded across one another Operating Instructions Loading Cups Glasses and Coffee Services Load small delicate items and long pointed cutlery in the upper rack Arrange items of crockery on the folding cups racks so that they are Offset from each other and water can reach all items he cup racks can be folded up out of the way for tall items Lay or hang wine champagne and brandy glasses in the cut outs on the cup racks Glasses beakers etc can also be placed on the two rows of prongs on the left of the upper rack 25 Operating Instructions 26 Fi I 1 2 Holding the upper basket at the rear Pull the upper basket out completely Holding the upper basket at the rear Adjusting the Height of the Upper Basket Maximum Height of the Dishes in the Upper Basket Lower Basketk With upper basket raised 22 cm 31 cm With upper basket lowered 24 cm 29 cm The height of the basket can also be adjusted when it is loaded Lowering the Upper Basket Pull the upper basket out completely right lift it as far as it will go and then lower it vertically The upper basket will engage in the lower posi tion Raising the Upper Basket right lift it as far as it will go and the
23. ebedingungen der rtlichen Part ner Diese k nnen dort eingesehen werden Further after sales service agencies overseas In these countries our AEG agents own guarantee conditions are appli cable Please obtain further details direct Autres agences trang res assurant le service apr s vente Dans ces pays les conditions de garantie des concessionnaires de la r gion sont valables Vous pouvez les consulter sur place Otros puntos de Postventa en el extranjero En estos pa ses rigen las condiciones de nuestros representantes locales las cuales pueden ser consultadas all mismo Ulteriori uffici del servizio tecnico assistenza clienti all estero In questi paesi sono valide le condizioni di garanzia dei partner locali Queste condizioni possono essere esaminante sul luogo Servicos de assist ncia t cnica no estrangeiro Nestes pa ses sdo v lidas as condic es de garantia dos concession rios locais podendo a ser consultadas Tov bbi vev szolg lati irod k k lf ld n Ezekben az orsz gokban a mi AEG vev szolg latainkn l saj t j t ll si felt telek alkalmazhat k A tov bbi adatokat k rj k k zvetlen l szerez z k be Servisne slu be Na garancijskem listu boste na li seznam pooblas enih servisnih slu b AEG 53 54 Service SERVICE In the section What to do if the most important sources of faults that you can rectify yourself are summarised If nevertheless you call i
24. eep them pressed The cycle display for the current cycle will flash for several seconds and then cease to be illuminated Release the function buttons The dishwashing cycle has been aborted Turning off the dishwasher will only interrupt a selected dishwashing cycle not abort it The dishwashing cycle will recommence after turning the dishwasher back on again Setting or changing the start delay Using the start delay timer you can adjust when within the next 19 hours the dishwashing cycle is to begin Setting the start delay Press the ON OFF button hours delay until the dishwashing cycle is to start is flashing in the multi display Press the button for the desired dishwashing cycle The length of the selected dishwashing cycle will flash for a moment in the multi display and then it will display the selected starting time again As soon as the number of hours is displayed without flashing the start delay has been activated The dishwashing cycle will start automatically following a countdown of the hours set Changing the start delay As long as the dishwashing cycle has not started you can still change the start delay set by pressing the DELAY TIMER button 33 Operating Instructions 34 I 1 Cancelling the start delay As long as the dishwashing cycle has not begun you are able to cancel the start delay Continue pressing the START DELAY button until the length of the selected dishwashi
25. ensing of rinse aid from the supply container must be activated The amount of rinse aid to be dispensed must be set Use only branded rinse aid for dishwashers Never fill the rinse aid con tainer with any another substance e g concentrated vinegar or dish washer cleaning agent This would damage the appliance Activating deactivating the inflow of rinse aid Some appliances are equipped with an additional 3 in 1 function If you use 3 in 1 dishwashing tablets and select the 3 in 1 function together with the dishwashing cycle the inflow of rinse aid does not have to be deactivated see 3 in 1 function Press the ON OFF button The LED in the ON OFF button will become illuminated If other indicators are also illuminated this means that a dishwashing cycle has been activated The dishwashing cycle must be deselected RESET Press function buttons 1 and 2 simultaneously for approx 2 seconds All other indicators will go out Press the function buttons 1 and 2 simultaneously and keep them pressed The LED indicators in function buttons 1 to 3 will flash Press function button 2 again The LED indicator for function button 2 will flash Operating Instructions Open the door Press the rinse aid compartment Fully open the rinse aid compartment The multi display will indicate the current setting Ud Inflow of rinse aid is deactivated id Inflow of rinse aid is activated factory setting
26. fitted with safety devices that prevent the wash water returning into the drinking water system and comply with the applicable plumbing regulations e he dishwasher can be connected to cold and hot water supplies up to max 60 C e The dishwasher must not be connected to open hot water appliances or instantaneous water heaters Permitted water pressure Lowest permitted water pressure Consult your installer if the water pres 1 bar 10 N cm 100 kPa sure is less than 1 bar Highest permitted water pressure In the case of a water pressure greater 10 bar 2100 N cm 1 MPa than 10 bar a pressure reduction valve must be used available from your dea ler Connect the inlet hose The water inlet hose must not be kinked crushed or entangled when it is being connected up Connect the threaded hose fitting ISO 228 1 2000 on the water inlet hose to a tap with an external thread 34 inch The inlet hose is equipped either with a plastic or with a metal connection nut Tighten plastic hose connection nuts by hand only Metal hose connection nuts must be tightened using an appropriate tool Finally visually check that it is water tight ensure that the tap is not dripping n order that access to the tap in the kitchen is not limited by the use of the dishwasher we recommend the installation of an additional tap or fitting a two way adapter to the existing tap f you need a longer water inlet hose than that s
27. gramme does not start Rust spots are visible in the washing compart ment There is a whistling noise during washing Dishwasher interior lighting does not work Possible Cause The door of the dishwasher is not closed properly Mains plug is not plugged in House fuse in defective In the case of dishwasher models with start delay timer A start delay is selected The washing compartment is made of corrosion resistant stainless steel Rust spots in the washing compartment are from particles from out side the appliance rust par ticles from the water pipe from pans cutlery etc Remove such spots with a commercially available stain less steel cleaner The whistling is not a cause for concern Mains plug is not plugged in Light bulb for the interior lighting is defective the wash result is not satisfactory The dishes are still dirty The wrong wash programme was selected he dishes were arranged in such a manner that water has not rea ched all parts The dish racks must not be overloaded The filter in the base of the washing compartment is dirty or incor rectly positioned Remedy Shut the door Insert mains plug Replace fuse If dishes are to be washed immediately cancel delay start timer Only wash cutlery and dis hes that are suitable for dis hwasher use Close the lid of the special salt container securely Use a different brand of detergent I
28. h programmes in conjunction with concentrated detergents reduces pollution and is good for your dishes these wash programmes are specially matched to the dirt dissolving properties of the enzymes in the concentrated detergent For this reason 50 C wash programmes in which concentrated detergents are used can achieve the same results that can otherwise only be achieved using 65 C pro grammes Detergent tablets Detergent tablets of different makes dissolve at different speeds For this reason some detergent tablets cannot develop their full cleaning power during short programmes Therefore please use wash program mes with pre wash when using detergent tablets Automatic Wash Programmes During AUTOMATIC programmes the amount of soiling on the dishes is determined by the degree of water clouding If the load is small and the dishes lightly soiled the pre wash main wash and rinsing elements of the programme are shorter and there is lower water consumption When the machine is fully loaded and the dishes very soiled the pre wash main wash and rinsing elements of the programme take lon ger and the water consumption is higher For this reason the programme duration water and energy consump tion levels for AUTOMATIC programmes can vary within the given ran ges see programme table In this way the dishes are always washed to an optimum while water and electricity consumption are kept low 29 Operating Instructi
29. hwasher There is a risk of an explo sion The anti flood system provides dependable protection against damage due to leaks For this system to function correctly the follo wing preconditions must be met The appliance must remain connected to the mains even when it is switched off The dishwasher must be correctly installed Always shut off the water supply at the tap when the dishwasher is not to be used for longer periods e g when you are away on holi day Operating Instructions e Do not sit or stand on the open door the appliance may tip over e n the event of a fault first close the tap then switch off the appliance and unplug it from the mains If the appliance is perma nently wired to the mains switch off the fuse s or unscrew them e Disposal Disposing of the Packaging Material Dispose of the dishwasher packaging material correctly All the pak kaging materials used are harmless to the environment and can be recycled e Plastic parts are marked with standard international abbreviations PE for polyethylene e g sheet wrapping material PS for polystyrene e g padding material always CFC free POM for polyoxymethylene e g plastic clips e Cardboard packaging is manufactured from recycled paper and should be deposited in the waste paper collection for recycling Disposal of old appliances As and when you cease to use your dishwasher please take it to a recycling centre or to
30. ing Instructions Activating deactivating the acoustic signal In addition to the optical display e g indicating the end of the cycle errors you can also choose to set an acoustic signal 1 Press the ON OFF button The LED in the ON OFF button will become illuminated i If other indicators are also illuminated this means that a dishwashing cycle has been activated The dishwashing cycle must be deselected RESET Press function buttons 1 and 2 simultaneously for approx 2 seconds All other indicators will go out 2 Press the function buttons 1 and 2 simultaneously and keep them pressed The LED indicator for function button 3 will flash 3 Press function button 3 The LED indicator for function button 3 will flash The multi display will indicate the current setting b Acoustic signal deactivated ib Acoustic signal activated ex factory setting 4 Pressing function button 3 will change the setting 5 Once the multi display is indicating the required setting press the ON OFF button The setting is now saved 19 Operating Instructions 20 In Daily Use s it necessary to refill with special salt or rinse aid Load cutlery and dishes into the dishwasher e Fill with dishwasher detergent e Select a wash programme suitable for the cutlery and dishes e Start the wash programme Loading cutlery and dishes AN Sponges household cloths and any object that can absorb water may not
31. me and if necessary to clean it The indica tor illuminates at regular intervals independent of the amount of soi ling of the filters Prior to using for the first time Prior to using for the first time remove all the clips with which the dish racks are secured for transport Then perform the following steps ts 1 Adjust the water softener 2 Fill with Special Salt for the Water Softener 3 Fill with Rinse Aid i Special salt and rinse aid must not be added if you use 3 in 1 detergent tablets 11 Operating Instructions 12 Water softener To avoid scale deposits on the dishes and in the dishwasher the dishes must be washed with soft water i e water with a low lime content The dishwasher therefore has a built in water softener in which tap water with a hardness of 4 d German degree and harder is softened with the aid of special salt Your water supplier will be able to inform you about the hardness and hardness range of the water in your area The water softener can be set manually using the water hardness switch it can also be set electronically using the buttons on the control panel In ed 51 70 43 50 37 42 29 36 23 28 19 22 15 18 11 14 4 10 under 4 Adjusting the hardness Water hardness ee Indication on 3 the multi dis In mmol l Range Manually Electronically play 9 0 12 5 103 UL 7 6 8 9 9 SL 6 5 7 5 IV 1 8 BL 5 1 6 4 7 L 40 5 0 6 BL 3 3
32. mme as at some programme stages the dishes are washed more energetically so that they will be cleaned more thoroughly 4 The consumption figures were determined under standard conditions They are intended as a guide only and depend on the loading For this reason figures may vary in practice 5 When the hardness setting is electronically adjusted to 10 the length of the dishwashing cycle may be slightly longer 31 Operating Instructions 32 Starting a dishwashing cycle I 1 2 IS 1 Check that the dishes and cutlery are stacked in the dishwasher in such a way that the spray arms are free to rotate Turn on the tap fully 3 4 Close the door Press the ON OFF button The LED in the ON OFF button will become illuminated Press the relevant button for the cycle required see Cycle Table The cycle indicator and the respective cycle stages in the cycle progress display will become illuminated The remaining time for the cycle will be shown in the multi display The selected cycle will begin after approximately 3 seconds The current stage of the programme will always be shown in the programme progress display During the dishwashing cycle the remaining time shown in the multi display may be adjusted according to amount of dishes degree of soi ling etc If an error message is displayed in the multi display after the cycle has begun please read the section What to do if
33. n customer service to resolve a problem listed in these instruction or because of an error made in operating the appliance the customer service engineer s visit is not free of charge even during the warranty period If you can not find any information on a specific malfunction in these operating instructions please contact customer service Please provide customer service the PNC number and the S No serial number you can find these on the rating plate The plate is on the inner edge of the door on the right E So that you always have these numbers at hand we recommend you to make a note of them here 55 E From the Electrolux Group The world s No 1 choice The Electrolux Group is the world s largest producer of powered appliances for kitchen cleaning and outdoor use More than 55 million Electrolux Group products such as refrigerators cookers washing machines vacuum cleaners chain saws and lawn mowers are sold each year to a value of approx USD 14 billion in more than 150 countries around the world AEG Hausger te GmbH Postfach 1036 D 90327 Nurnberg http www aeg hausgeraete de 9 Copyright by AEG 822 960 710 00 0603 Subject to change without notice
34. n lower it vertically The upper basket will engage in the higher position Operating Instructions Filling with Detergent IS 1 Only use dishwasher detergent Fill with detergent Prior to the start of a wash programme not for the pre wash pro gramme The detergent is released into the wash water during the programme Please observe the manufacturer s dosing and storage recommendati ons as stated on the detergent packaging The detergent compartment is on the inside of the dishwasher door If the lid is closed press release button 1 The lid springs open Fill the detergent dispenser with detergent The markings indicate the dosing levels 20 corresponds to approx 20 ml of detergent 30 corresponds to approx 30 ml of detergent Close the lid and press until it locks into place If the dishes are very heavily soiled put additional detergent into the adjacent chamber 2 This detergent will take effect during the pre wash i ES D W 27 Operating Instructions 28 is 1 Use of 3 in 1 Combi Detergent Tablets General Advice These products are tablets with combined detergent rinse aid and salt functions Before using these products you should first check that the water hard ness in your supply is compatible with the use of these products as per the detergent manufacturers instructions on the product packaging
35. ng cycle appears in the multi display The selected dishwashing cycle will begin immediately Changing the dishwashing cycle after the start delay has been set As long as the dishwashing cycle has not started you can still change the start delay set by pressing a cycle button Press the button for the new dishwashing cycle and hold it down First the indicator for the dishwashing cycle that has just been selected will flash After several seconds only the indicator for the new dishwashing cycle will be flashing Release the cycle button The newly selected dishwashing cycle will start automatically following a countdown of the hours set Load Sensing Sensor Logic If a wash programme is started even though there are only a few dishes in the upper and or lower rack an intelligent electronic system adjusts the amount of water and the duration of the wash programme to the number of dishes By this means it is possible to wash only a few dishes quickly and economically At half load 6 place settings up to 2 litres of water and 0 2 kWh of electricity are saved Operating Instructions Switching Off the Dishwasher Only switch the dishwasher off when the multi display indicates 0 for the remaining programme time and is illuminated on the pro gramme progress display If the acoustic signal has been switched on there will be a continuous signal for 15 seconds at the end of the wash programme Press the ON OFF s
36. nge over switch the additional instructions on the change over diagram in the mains connector box must be observed Prior to connecting ensure that the mains voltage and current rating at the site of installation match the nominal voltage and current rating given on the rating plate The required fuse protection is also to be found on the rating plate To isolate the dishwasher from the mains remove the mains plug Important The plug must still be accessible after the appliance has been installed If the appliance is hard wired to the mains supply then it must be safely isolated from the mains within the electrical installation with switches intended to ensure all pole N L1 disconnection shall be directly connected to the supply terminals and shall have a contact separation fuses cut outs current trips or similar of at least 3mm in each pole Installation and Connection Instructions Connections The water inlet and drain hoses as well as the mains cable must be connected beside the dishwasher as there is insufficient space behind the appliance The plumbing and electrical installation example given below can only be regarded as a recommendation the actual situation where the dish washer is to be installed will define the exact installation available connections local electricity and water board regulations for connec ting up appliances etc Two 45 or Straight Connections Outer 19 mm Length 30 mm Double tap Wa
37. nsert mains plug Contact customer service Detergent was not used or too little was used In the case of scale deposits on the dishes the special salt container is empty or the water softener is incorrectly adjusted 39 Operating Instructions The drain hose is incorrectly laid The dishes are wet and dull Rinse aid was not used The rinse aid container is empty There are streaks milky spots or a bluish coating on glasses and dishes Decrease rinse aid dosing There are dried water drops on the glasses and dishes Increase rinse aid dosing he detergent may be the cause Contact the detergent manufactu rer s consumer advisor Technical Data Capacity 12 place settings including serving dishes Permitted Water ae OR Pressure 1 10 bar 210 100 N cm 0 1 1 0 MPa Information on the electrical connection is given on the rating plate on the inner edge of the dishwasher door on the right Electrical Connection Dishwasher Free Standing Appliances Dimensions 850 x 600 x 600 H x W x D in mm Max Weight 54 Kg Dishwashers that Can Be Integrated Built In Dishwashers Dimensions 820 880 x 596 x 570 H x W x D in mm Max Weight 50 Kg Dishwashers that Can Be Fully Integrated Dimensions 820 880 x 596 x 546 550 H x W x D in mm Max Weight 50 Kg C This appliance conforms with the following EU Directives 73 23 EWG dated 19 02 1973 Low Voltage Directive
38. ons Selecting the Wash Programme Programme Table Choose the most suitable wash programme with the aid of this table Type of Dishes In Addition Type of Soiling Suitable Wash Pro gramme Programme Sequence Consumption Figures Duration Energy Water Dinner Service and Cooking Utensils heavily to lightly soiled dried leftovers AUTOMATIC Pre Wash Main Wash Rinsing Final Rinse Drying 90 110 minutes 1 10 1 40 kWh 13 20 litres Dishes without Pans e just used aver age to slightly soiled particularly suita ble when concentra ted detergents are used 30 MIN Main wash Final rinse 30 min 0 8 kWh 8 litres Dinner Service and Cooking Utensils heavily soiled dried on leftovers parti cularly egg white and thik keners INTENSIV Ow Pre Wash Main Wash 2x Rinsing Final Rinse Drying Y 110 120 minutes 1 75 1 95 kWh 20 22 litres 1 This programme is not suitable when left overs have dried on 2 Noise levels vary at different stages of the wash programme as at some programme stages the dishes are washed more energetically so that they will be cleaned more thoroughly 3 The consumption figures were determined under standard conditions They are intended as a guide only and depend on the loading For this reason figures may vary in practice 4 When the hardness setting is electronically adjusted to 1
39. ose against sliding off the edge of the wash basin Pass a piece of cord through the hose elbow and fix it to the wall or the tap 47 Installation and Connection Instructions 48 Leak prevention system To avoid damage caused by water leakage the dishwasher is equipped with a leak prevention system In the event of a fault the safety valve in the appliance immediately interrupts the inflow of water and the drain pump is activated In this way water can neither escape nor overflow Any remaining water in the appliance is automatically pumped out The leak prevention system also works when the appliance is switched off the appliance must however not be disconnected from the mains In the event of a fault when the appliance is switched on a buzzing tone can also be heard Electrical connection AN In compliance with electric company technical requirements for mains connections hard wired connections to the mains may only be made by approved electri cians When connecting the appliance observe the German VDE regulations and if applicable any additional conditions required by your local elec tricity supplier Following installation live parts and live insulated wiring must not be accessible using a finger test in accordance with EN 60335 DIN VDE 0700 Information on the electrical connection can be found on the rating plate on the right side of the inner edge of the dishwasher door If the appliance has a cha
40. ppliances are equipped with an additional 3 in 1 function If you use 3 in 1 dishwashing tablets and select the 3 in 1 function together with the dishwashing cycle the inflow of special salt does not have to be deactivated see 3 in 1 function Set the water softener manually and electronically to the desired water hardness Manual Electronic Multi display Ng setting setting indicator a Sl 0 1 iL Do not add special salt Addition of special salt 0 1 2 10 e Lto il via salt supply container factory setting Operating Instructions I 1 Juno Undo the lid on the salt container by Only when using for the first time Place the funnel supplied on the con Clean any salt remnants on the container opening Turn the lid clockwise to the stop otherwise special salt will leak into If the water softener is electronically set at 1 for the purpose of using detergent that includes special salt the special salt indicator is deacti vated Adding special salt If you are using dishwasher detergent and special salt separately add the special salt Before using the dishwasher for the first time When the indicator for special salt S is illuminated on the control panel Open the door remove the lower rack turning it anticlockwise fill the salt container with water tainer opening Fill the container with special salt through the funnel the capacity of the container is app
41. rox 1 0 1 5 kg depending on the grain size Do not overfill the salt container with special salt The water expelled by filling the salt container with special salt runs out of the salt container onto the base of the washing compartment This is not a cause for concern the water will be pumped out at the start of the next wash programme the wash water this could lead to poor wash results To avoid this run a rinse programme after filling the salt container with special salt This will wash away salt water and any salt crystals that have been spilt Depending on the size of the salt grains it can take several hours for the salt to dissolve in the water and the special salt indicator S to extinguish The setting of the water softener and thus the consumption of salt are dependent on the hardness of the local water 15 Operating Instructions RINSE AID Rinse aid ensures that your dishes gleam and are free from spots and that your glasses are clear Rinse aid can be added in one of two ways e f you are using dishwasher detergent that already contains rinse aid the detergent including the rinse aid is put into the detergent compartment In this case the dispensing of rinse aid from the supply container must be deactivated to avoid a double dosage f you are using dishwasher detergent and rinse aid separately the rinse aid is to be put into the rinse aid supply container In this case the disp
42. t on a table or work surface open the two part handle remove cutlery close the two part handle Operating Instructions Loading Pans Frying Pans and Large Plates Load large and heavily soiled dishes in the lower rack Plates up to 29cm in diameter Your dishwasher has one of the following four types of lower rack Type 1 None of the plate inserts in the lower rack can be removed Type 2 The right hand plate inserts in the lower rack can be fol ded over to the left i To ease the loading of large items the two right hand plate inserts in the lower rack can be folded over to the left t 1 Slightly lift the right plate insert 2 Fold the plate insert to the left y A SY a D 0 0 22 y A 3 0 i 0 0 3 Bl 0 i ZZZU TT TTI D 1 23 Operating Instructions 24 i Type 3 The right hand plate inserts in the lower rack can be fol ded across one another To ease the loading of large items ee y the two right hand plate inserts in the lower rack can be folded across 0 one another 0 1 1 0 ZZZV TTT TTA 0 Type 4 The two rear plate inserts in the lower rack can be folded across one another To
43. ter drain Water inlet Water Mains Water Mains socket Mains inlet cable drain cable 49 Service Departments 50 U A E Abu Dhabi Universal Trading Company P O Box 43 99 Tel 335331 Egypt Middle East Commercial Center P O Box 19 Kairo Heliopolis Tel 29917 31634 Australia ANDI Co Pty Ltd 9 Kingston Town Close Oakleigh VIC 3166 Tel 03 9569 1235 Fax 03 9569 1450 Bahrain Arabian Gulf A A Zayani amp Sons P O Box 9 32 Bahrain Tel 261060 Bulgaria Electrolux Bulgaria E 0 0 D 91 Levski Blvd 1000 Sofia Tel 2 806676 Fax 2 980 5276 Cyprus Hadjikyrlakos amp Sons Ltd Prodromou 121 P O Box 21587 Nicosia 1511 Service Telephones Nicosia 02 481226 Limassol 05 562182 Larnaca 04 633929 Paphos 06 932 699 SERVICE DEPARTMENTS Jordan Jordan Household Supply Co Ltd P O Box 3 68 Amman Tel 69 70 50 Kanada EURO LINE Appliances 2150 Winston PARK Drive 20 Oakville Ontario L6H 5V1 Tel 905 829 3980 Fax 905 829 3985 Korea South Core Incorp 3 F Chewoo Bldg 200 Nonhyun Dong Kangnam Ku Seoul Telefon 82 2 549 89 61 Croatia Electrolux D O O Suplova 7 10000 Zagreb Tel 161 19512 Fax 1 61 19513 Kuwait Arabian Gulf Ali Al Ghanim Est P O Box 10 83 Tel 5322463 Fax 5242114 Lebanon Adib amp
44. the nominal voltage and type of supply on the rating plate match that of the sup ply where the appliance is to be installed The fuse rating is also to be found on the rating plate e For information on how to correctly install and connect up your dish washer please read the Installation section Multiway plugs con nectors and extension cables must not be used This could constitute a safety hazard Child Safety e Children often do not recognise the hazards associated with the use of electrical appliances It is therefore important that you ensure children are adequately supervised and that you do not allow child ren to play with the dishwasher there is a risk that children can shut themselves inside the appliance risk of suffocation Packaging materials e g films styrofoam can be dangerous for children Risk of suffocation Keep packaging away from children e Detergents can cause burns to the eyes mouth and throat or even cause choking Please observe the manufacturer s safety instructions for cleaners and detergents e The water in your dishwasher is not suitable for drinking If there are still remnants of detergent in the appliance there is a risk of burns When disposing of the dishwasher unplug from the mains cut off and dispose of the mains cable Break the door lock so that the door no longer shuts Operating Instructions General Safety e Repairs to the dishwasher are only to be carrie
45. tinuously repeated warning tone can be heard the cycle indicator for the selected cycle is flashing The gt indicator is continuously illuminated Error code 1B is displayed in the multi dis play There is no water run ning into the dishwasher Two short continuously repeated warning tones can be heard the cycle display for the selected cycle is flashing error code 20 is displayed in the multi dis play Possible cause The tap is blocked or furred with lime scale The tap is turned off The filter where present in the threaded hose fitting at the water inlet valve is blok ked Filters in the base of the washing compartment are blocked The water inlet hose has not been correctly laid The siphon is blocked The water drain hose has not been correctly laid Remedy Clean tap Turn the tap on Clean the filter in the threaded hose fitting Press the button for the commenced dishwa shing cycle then abort the dishwashing cycle by pressing RESET see chapter Starting a dis hwashing cycle Star ting a dishwashing cycle clean out the filters see chapter Cleaning the filters Check hose installation Clean out siphon Check hose installation 37 Operating Instructions 38 Malfunction Three short continuously repeated warning tones can be heard error code 3 is displayed in the multi dis play One long continuously repeated warning tone can
46. ttons Door Handle Set Start Delay Indicators me O sanesa l Q ores i ne AID a 0 0 wo lO ELO Ornan DATER mO 10 O ud penes 2 4 m Function Buttons Control Panel Multi Display Cycle progress display The control panel consists of the ON OFF button and the programme buttons with LED displays Function buttons In addition to the stated wash programme the fol lowing functions can also be set using these buttons Function Button 1 Adjust the water softener Function Button 2 Switch rinse aid supply on and off Function Button 3 Switch acoustic signal on and off Function Button 4 is not occupied The Multi Display can display the hardness setting to which the water softener is set whether the rinse aid supply is switched on off whether the signal tone is switched on or off the start delay that is set how long the current wash programme can be expected to last which fault has occurred on the dishwasher Cycle progress display The current stage of the programme will always be shown in the cycle progress display Operating Instructions Indicators have the following significance 3 Refill with special salt MX Refill with rinse aid Open the tap e Clean the dishwasher s filter system The dishwasher door is open NANG The middle spray arm is jammed i The e indicator is intended to remind you to check the filters in the dishwasher from time to ti
47. upplied VDE appro ved complete hose sets are to be used These are available from your local Service Force Centre 45 Installation and Connection Instructions 1 The following section is only applicable to dishwashers that have a safety valve on the threaded hose fitting for the tap Water inlet hose with safety valve After connecting the double walled water inlet hose the safety valve is next to the tap Therefore the water inlet hose is only under pressure while the water is running If the water inlet hose starts to leak during this operation the safety valve cuts off the running water and the draining pump in the dishwasher is switched on Please take care when installing the water inlet hose The distance between the bottom edge of the safety value and the floor on which the dishwasher is standing must be at least 30 cm The electrical cable for the safety valve is in the double walled water inlet hose Do not immerse the LL water inlet hose or the safety valve in water If the water inlet hose or the safety valve is damaged remove the mains plug immediately A water inlet hose with safety valve must only be replaced by a specialist or Customer Services Place the water inlet hose in such a way that it is never higher than the bottom edge of the safety valve min 30cm Installation and Connection Instructions Water drain Drain hose The drain hose must not be kinked
48. witch All indicators go out Hot steam may escape if the door is opened immediately after the end of the programme Therefore Open the door carefully If you do not switch off the dishwasher the acoustic signal will sound again 3 minutes later and 6 minutes later Emptying the Dishwasher Hot dishes can be sensitive to knocks The dishes should therefore be allowed to cool down before removing them from the appliance Leave the dishes in the dishwasher for approx 15 minutes after the end of the programme so that they dry better and can cool down Empty the lower rack first then the upper rack This will avoid any water left on the upper rack dripping onto the dishes in the lower rack and causing water spots Care and Cleaning AN Do not under any circumstances use furniture care products or aggres sive cleaners e f necessary clean the controls only with a soft cloth and pure warm water Occasionally check the internal containers door seal and water inlet for soiling clean if necessary 35 Operating Instructions 36 i is 1 The dishwasher filter system compri Turn the handle about Ya a turn anti Take hold of the coarse fine filter 1 Clean all filters thoroughly under Remove the flat filter 4 from the Put the flat filter back in the base of Place the coarse fine filter in the Put the filter combination in place Cleaning the Filter The filters
Download Pdf Manuals
Related Search