Advantech PPC-175T User's Manual
Contents
1. 52 Figure A 21 Removing the CPU ssssee 52 Figure A 22 Removing the SDRAM module 53 PCI Card Size Limits 56 Figure B 1 PCI Card Dimensional Limits 56 xiii PPC 175T User Manual General Information This chapter gives background information on the PPC 175T Sections include B Specifications m Dimensions Chapter 1 General Information 1 1 Introduction Advantech PPC 175T is an Intel Pentium M processor based Panel PC with a bright 17 LCD display The powerful Pentium M Celeron M CPU and Intel 855GME chipset brings the most dynamic applications to life without sacrifices to any industrial reliabil ity Internal CF card interface can treat as alternative HDD solution for OS booting and Mini PCI interface can equip with many expansion cards such as Wireless LAN card to extend mobility application Front bezel LEDs display PPC Power on HDD and LAN operating status and a built in front light sensor can automatically adjust the brightness level in different operating conditions In order to satisfy customers secu rity concerns PPC 175T is also offered in a two LAN port configuration customers can contact local sales for OEM orders 1 2 Specifications 1 2 0 1 General W Dimensions W x H x D 442 x 362 x 111 5 mm 17 4 x 14 25 x 4 39 W Weight 7 52kg 16 56lbs B Power supply AC model 100 watts Input voltage 1002. Figure 2 4 Rear view of the panel PC 9 PPC 175T User Manual 2 2 Preparing for First time Use Before commencing set up of the panel PC system the following items should be available WB Keyboard H Mouse for system software installation 2 3 Installation Procedures 2 3 1 Connecting the power cord The panel PC can only be powered through an AC electrical outlet 100 250 volts 50 60 Hz Be sure to handle the power cords by holding the plug ends only Follow these procedures in order 1 Connect the female end of the power cord to the AC inlet of the panel PC 2 Connect the 3 pin male plug of the power cord to an electrical outlet 2 3 2 Connecting the keyboard and mouse Connect the PS 2 mouse and keyboard to the I O section of PPC If using a serial mouse and the panel PC has a touchscreen it is possible to connect the mouse to any COM port except COM4 2 3 3 Switching on the power Switch on the power switch which is located inside the bottom side cover 2 4 Running the BIOS Setup Program The panel PC will be properly set up and configured by the dealer prior to delivery However it may be necessary to use the panel PC s BIOS Basic Input Output Sys tem setup program to change the system configuration information such as the cur rent date and time or the type of hard drive The setup program is stored in read only memory ROM It can be accessed either when you turn on or reset the panel PC by pressin
3. data AN Ex There is a danger of a new battery exploding if it is incorrectly installed Do not attempt to recharge force open or heat the battery Replace the battery only with the same or equivalent type recom mended by the manufacturer Discard used batteries according to the manufacturer s instructions Note Ifthe unit you have bought is basic i e without a CPU HDD or SDRAM you will find this optional item in the accessory box Document Feedback To assist us with making improvements to this manual we welcome comments and constructive criticism Please send all suggestios in writing to support advan tech com Packing List Before setting up the system check that the items listed below are included and in good condition If any item does not accord with the table please contact your dealer immediately E PPC 175T series panel PC B User s manual m Accessories for PPC 175T m A power cord is not included with this product but is available for purchase as a separate option B Drivers and Utilities CD ROM disc B Heatsink optional refer to Notes 1 and 2 below Note Ifthe supplied unit is the basic version i e without a CPU HDD or SDRAM look for optional items in the accessory box Note If installing an Intel processor it is necessary to install a heat sink above the CPU This will avoid heat damage to the CPU V PPC 175T User Manual Additional Information and Assista
4. PPC 175T Pentium Celeron M Processor Based Panel PC with 17 Color TFT LCD Display Trusted ePlatform Services AD ANTECH Copyright The documentation and the software included with this product are copyrighted 2007 by Advantech Co Ltd All rights are reserved Advantech Co Ltd reserves the right to make improvements in the products described in this manual at any time without notice No part of this manual may be reproduced copied translated or transmitted in any form or by any means without the prior written permission of Advantech Co Ltd Information provided in this manual is intended to be accurate and reliable How ever Advantech Co Ltd assumes no responsibility for its use nor for any infringe ments of the rights of third parties which may result from its use Acknowledgements Award is a trademark of Award Software International Inc VIA is a trademark of V A Technologies Inc IBM PC AT PS 2 and VGA are trademarks of International Business Machines Corp Intel and Pentium are trademarks of Intel Corporation Microsoft WindowsZE is a registered trademark of Microsoft Corp RTL is a trademark of Realtek Semi Conductor Co Ltd Winbond is a trademark of Winbond Electronics Corporation Ricoh is a trademark of Ricoh Company LTD All other product names or trademarks are properties of their respective owners m For more information on this and other Advantech products please visit our websites a
5. ment and must be easily accessible 5 Keep this equipment away from humidity 6 Put this equipment on a reliable surface during installation Dropping it or letting it fall may cause damage 7 The openings on the enclosure are for air convection Protect the equipment from overheating DO NOT COVER THE OPENINGS 8 Make sure the voltage of the power source is correct before connecting the equipment to the power outlet 9 Position the power cord so that people cannot step on it Do not place anything over the power cord 10 All cautions and warnings on the equipment should be noted 11 Ifthe equipment is not used for a long time disconnect it from the power source to avoid damage by transient overvoltage 12 Never pour any liquid into an opening This may cause fire or electrical shock 13 Never open the equipment For safety reasons the equipment should be opened only by qualified service personnel 14 If one of the following situations arises get the equipment checked by service personnel 15 The power cord or plug is damaged 16 Liquid has penetrated into the equipment 17 The equipment has been exposed to moisture 18 The equipment does not work well or you cannot get it to work according to the user s manual 19 The equipment has been dropped and damaged 20 The equipment has obvious signs of breakage 21 DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE MAY GO BELOW 20 C 4
6. Serial COM Ports ur 17 Figure 3 4 W O ports ssssem em 17 VGA POM ssid ante nieinin aii aaa 17 USB Ports terere dst ena Be ener nuu 17 Audio Iriterface i 2a 18 Ethernet E 18 Front Bezel LED and Light Sensor sse 18 Figure 3 5 LED amp light sensor ssee 18 Touchscreen Optional ooooocccccnnnocicinonnnoccnccnnnconnncnnnnancnn ronca 19 Hardware Installation 22 Jumpers and CONMNECtOSS cococcccccnnconinconcnnncnnnnncnnnnnnnnnnnnnnnnnnnnnno 22 Disassembling the Panel PC sssssseeen 22 Figure 4 1 Unfastening the HDD side cover 22 Figure 4 2 Unfastening the rear cover eseese 23 Figure 4 3 Disconnecting the fan connector 23 Figure 4 4 The PPC without the Rear Cover 24 Installing the 2 5 Hard Disk Drive sseeeeeeeees 24 xi PPC 175T User Manual 4 4 4 5 Chapter 5 5 1 Chapter 6 6 1 6 2 Chapter 7 7 1 Appendix A A 1 PPC 175T User Manual Figure 4 5 Fastening the HDD metal frame to the HDD 24 Figure 4 6 Plugging in the EIDE cable 25 Figure 4 7 Aligning the HDD frame eee 25 Installing the Central Processing Unit CPU 26 Figure 4 8 Placing the CPU in the socket 26 Figure 4 9 Tightening the screws on
7. radio Connect the audio device to the system See Fig 3 4 Install the driver before using the device 3 10 Ethernet External devices on the network may be connected to the system through the exter nal Ethernet port located on the bottom of the system unit 1 Be sure the panel PC is turned off 2 Connect the external device s to the panel PC 3 Turn on the panel PC and the external device s Bn mas Note Customer can order two LAN ports or Change default LAN port to Giga LAN via Advantech OEM processes 3 11 Front Bezel LED and Light Sensor On the front bezel of the PPC 175T there are three LEDs to indicate Power HDD LAN A light sensor with built in panel brightness level control completes the array See Figure 3 5 Figure 3 5 LED amp light sensor Details about the light sensor are available on the Driver CD inside the light sensor folder The Advantech Smart Backlight Utility is aimed to help the user adjust the backlighting of the panel Users can also configure the backlight of the panel from desktop utility switch between manual mode auto mode set the backlight value The SUSI software library is also available to support configuration and operation of the system controls and sensors PPC 175T User Manual 18 3 12 Touchscreen Optional The touchscreen is connected to the internal RS 232 port Its function is similar to that of a mouse There are 3 kinds of touchscreens that support the PPC 175
8. the CPU 27 Figure 4 10 Placing the heatsink and fan on the CPU 27 Figure 4 11 Fastening the CPU module to the motherboard 28 Installing the DDR SDRAM Memory Module 29 Figure 4 12 Placing the memory module in the DIMM 29 Jumpers amp Connectors 32 Jumpers and Connectors ccccccceceeceeeeeeeeeeeeneeccaeeeeeeeeeeees 32 5 1 1 Setting jumpers soiree ea Ea 32 5 1 2 JUMP tra nant lr aen eda 32 Table 5 1 PCI slot voltage setting JP2 33 Table 5 2 Clear CMOS JP3 nnennnnennnnnnnennenennn 33 Table 5 3 LVDS voltage setting JP5 ssssss 33 Figure 5 1 Jumpers and connectors on the PPC 175T mother board ada 34 DNS CORTIG lors est iren Yet exe a a 35 Table 5 4 PPC 175T connectors table 35 Driver Installation 38 Driver Installation 38 Updating Driver Searching on the Advantech Website 38 Pin Assignments 40 MAN Heading01 style Arial Bold 18pt MAN H1 color 40 7 1 1 HeadingO2 style Arial Bold 14pt MAN H1 color 40 Table 7 1 MAN TableTitle style Arial Bold 12pt Black 40 Figure 7 1 Test figure e unneesennnssnnsennnnnnennannnnnnnenennnnnnnen 40 Figure 7 2 Another test figure 40 Figure 7 3 A third test figure
9. 250 VAC 50 60 Hz Max Output voltage 3 3V 6A 5V 38A 12V 5A 12V 0 5A 5VSB 0 75A 3 3V 5V total 50W max W Disk drive housing Space for one 2 5 HDD one 12 7 mm compact CD ROM drive W Front panel IP65 protection not for the model with SAW touchscreen 1 2 0 2 Standard PC functions W CPU Supports Intel Pentium M and Celeron M up to 1 8 1 5GHz BIOS Award 4 MB Flash BIOS supports Plug amp Play APCI Chipset Intel 855GME ICH4 RAM Two 184 pin DDR DIMM sockets up to 2GB DDR SDRAM Serial ports Three serial ports with three RS 232 ports COM1 2 and 3 one RS 232 422 485 port COM2 which can be selected from BIOS set up program All ports are compatible with 16550 UARTs Universal serial bus USB port Supports up to four USB V2 0 ports PCI bus expansion slot Accepts one PCI bus card Watchdog timer 255 level interval timer set up by software Battery 3 0 V 196 mA lithium battery 1 2 0 3 AGP SVGA Flat panel interface B Chipset Intel 855GME chipset with integrated Intel Extreme Graphics 2 B Display memory optimized shared memory architecture supports up to 64MB frame buffer using system memory W Display type Simultaneously supports CRT and flat panel displays EL LCD and gas plasma W Display resolution Supports non interlaced CRT and TFT LCD displays up to 1024 x 768 256K PPC 175T User Manual 2 1 2 0 4 Audio function B Chipset Realtek ALC650 W Audio controller AC97 Ver 2 0 com
10. 8 Unfasten the side screws on the HDD module and remove the left side plate Figure A 8 Unfastening the HD D module 9 Remove the right side plate and lift out the HDD Figure A 9 Removing the HDD PPC 175T User Manual 46 10 Disconnect the HDD cable from the PPC 175T motherboard gt Figure A 10 Disconnecting the HDD cable 11 Loosen the screws on the bracket holding the HDD module Figure A 11 Loosening the screws on the HDD bracket 47 PPC 175T User Manual 12 Loosen the screws on the CD ROM module Figure A 12 cas the screws on the CD ROM module 13 Carefully push out the fixed brace holding the CD ROM Figure A 13 Pushing out the brace holding the CD ROM PPC 175T User Manual 48 14 Remove the fixed brace Figure A 14 Removing the fixed brace 15 Unfasten the CD ROM PCMCIA slot cover Figure A 15 Unfastening the CD ROM PCMCIA slot cover 49 PPC 175T User Manual 16 Remove the CD ROM PCMCIA slot cover Figure A 16 Removing the CD ROM PCMCIA slot cover 17 Remove the CD ROM module PPC 175T User Manual 50 18 Disconnect the CD ROM connector je Figure A 18 Disconnecting the CD ROM connector 19 Unfasten the four screws on the CPU module and remove it ES Figure A 19 Removing the CPU module 51 PPC 175T User Manual 20 Unsfasten the CPU socket j A Ware Ta AH A r f 5 A4 YA Figure A 20 Unfa
11. An arrow is printed on the motherboard to indicate the first pin of each jumper 5 1 2 Jumpers The motherboard of the Vehicle Mounted Computer has a number of jumpers that help configure the system It also has LED indicator lamps that display the system operation status The table below lists the function of each jumper and LED The motherboard of the PPC 175T has a number of jumpers that allow you to config ure your system to suit your applications PPC 175T User Manual 32 5 1 2 1 PCI slot voltage setting JP2 The panel PC supports 5V and 3 3V PCI_VIO slot voltages The default voltage is 3 3V closed pins 1 2 5V may be selected by closing jumpers 2 3 Table 5 1 PCI slot voltage setting JP2 3 3V default 5V 5 1 2 2 Clear CMOS JP3 This jumper erases the CMOS data and resets the system BIOS information Table 5 2 Clear CMOS JP3 Normal operation default Clear CMOS 5 1 2 3 LVDS voltage setting JP5 The panel PC supports 5V and 3 3V LVDS voltages The default voltage is 3 3V closed pins 1 2 5V may be selected by closing jumpers 2 3 Table 5 3 LVDS voltage setting JP5 3 3V default 5V 33 PPC 175T User Manual 5 1 2 4 Jumper and Connector Locations JP3 CN12 CN34 JP5 CN16 CN30 CN13 CN8 amp CN19 Figure 5 1 Jumpers and connectors on the PPC 175T motherboard PPC 175T User Manual 34 5 1 3 Connectors Onboard connectors link the panel PC to external devices such as hard
12. F OR ABOVE 60 C 140 F THIS COULD DAMAGE THE EQUIPMENT THE EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT 22 CAUTION DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER DISCARD USED BATTERIES ACCORDING TO THE MANUFACTURER S INSTRUCTIONS 23 The sound pressure level at the operator s position according to IEC 704 1 1982 is no more than 70 dB A DISCLAIMER This set of instructions is given according to IEC 704 1 Advantech disclaims all responsibility for the accuracy of any statements contained herein vii PPC 175T User Manual Wichtige Sicherheishinweise 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Bitte lesen sie Sich diese Hinweise sorgf ltig durch Heben Sie diese Anleitung f r den sp teren Gebrauch auf Vor jedem Reinigen ist das Ger t vom Stromnetz zu trennen Verwenden Sie Keine Fl ssig oder Aerosolreiniger Am besten dient ein angefeuchtetes Tuch zur Reinigung Die NetzanschluBsteckdose soll nahe dem Ger t angebracht und leicht zug nglich sein Das Ger t ist vor Feuchtigkeit zu sch tzen Bei der Aufstellung des Ger tes ist auf sicheren Stand zu achten Ein Kippen oder Fallen k nnte Verletzungen hervorrufen Die Bel ftungs ffnungen dienen zur Luftzirkulation die das Ger t vor berhit zung sch tzt Sorgen Sie daf r daB diese Offnungen nicht abgedeckt werden Beachten Sie bei
13. RAM Figure 4 12 Placing the memory module in the DIMM 29 PPC 175T User Manual Jumpers and Connectors This chapter gives information on setting jumpers and using the connectors on the PPC 175T motherboard Sections include E Setting Jumpers E Jumper and Connector Locations B Connectors Chapter 5 Jumpers amp Connectors 5 1 Jumpers and Connectors This chapter supplies more detailed information about the internal jumper settings and an outline of the I O ports avaialable on the PPC 175T 5 1 1 Setting jumpers The Panel PC can be configured to match the needs of each application by setting the jumpers A jumper is the simplest kind of electrical switch It consists of two metal pins and a small metal clip often protected by a plastic cover which slides over the pins to close the circuit and connect them To close a jumper connect the pins with the clip To open a jumper remove the clip Sometimes a jumper has three pins labeled 1 2 and 3 In this case it is possible to connect either pins 1 and 2 or pins 2 and 3 to each other Open Closed Closed 2 3 The jumper settings are schematically depicted in this manual as follows Open Closed Closed 2 3 A pair of needle nose pliers may be helpful when working with jumpers If there are any doubts about the best hardware configuration for a particular application contact the local distributor or sales representative before making any changes
14. T Sections include B CD ROM Drive m PCMCIA m PS 2 Mouse and Keyboard m PCI Bus Expansion m Serial COM Ports m VGA Port B USB Ports E Audio Interface B Ethernet B Front Bezel LED and Light Sen sor m Touchscreen Optional Chapter3 Using the Panel PC 3 1 Introduction This chapter describes basic features and procedures for using the panel PC Topics covered include the floppy drive CD ROM drive I O ports and the touchscreen 3 2 CD ROM Drive optional It is possible to use the USB external optical device or order the PPC 175T which is equipped with slim optical devices To insert a CD ROM disc press the eject button on the CD ROM drive To eject a CD ROM disc first ensure that the drive activity light is not active Then press the eject button on the drive Figure 3 1 Inserting and ejecting a CD ROM PPC 175T User Manual 14 3 3 PCMCIA Memory Flash Cards are inserted and ejected in much the same way as diskettes To insert a Flash Memory card align the card with the socket and slide the card into the socket until it locks into place Take note that some FlashMemory cards must be properly configured thorugh the operating system before they can be used for data storage See the Flash Memory card manual for details To eject a Flash Memory card first ensure that the panel PC is not accessing the memory card or device Then press the appropriate eject button on the socket Figure 3 2 Inserti
15. T resis tive capacitive and SAW type It is necessary to install the touchscreen driver before it will function The touch screen drivers for various operating systems are stored on the CD ROM disc inside the accessory box 19 PPC 175T User Manual Hardware Installation This chapter gives instructions for installing hardware devices on the PPC 175T Sections include m Jumpers and Connectors m Disassembling the Panel PC E Installing the Central Processing Unit CPU B Installing the DDR SDRAM Memory Module Chapter 4 Hardware Installation 4 1 Jumpers and Connectors The panel PC consists of a PC based computer that is housed in a metal shielding case with a plastic cover on the rear and bottom All the computer devices like the CPU HDD SDRAM and power supply are all readily accessible after removing the rear panel or the HDD cover Any maintenance or hardware upgrades can be easily completed after removing the rear panel and or HDD cover For information about complete disassembly of the panel PC refer to Appendix B Warning Do not remove the plastic rear cover until verifying that no power is flow ing within the panel PC Power must be switched off and the power cord A must be unplugged Each time the panel PC is serviced users should be aware of this condition 4 2 Disassembling the Panel PC The following are standard procedures for disassembling the panel PC before upgrading the system All procedures
16. Unit CPU The panel PC is equipped with a central processing unit CPU that can be upgraded to improve system performance The panel PC provides one 478 pin ZIF Zero Inser tion Force socket or Socket 478 The CPU must be fitted with an appropriate heat sink and CPU fan to prevent overheating Warning The CPU may be damaged if operated without a heat sink and if the fan N is not connected to the CPU fan power connector Caution Always disconnect the power cord from your panel PC when you are working on it Do not make connections while the power is on as sen A sitive electronic components can be damaged by the sudden rush of power Only experienced electronics personnel should open the panel PC Follow these instructions to install a CPU 1 Place the CPU carefully into the socket taking care to align it properly PPC 175T User Manual 26 2 Fasten the screw on the CPU socket mounting plate Figure 4 9 Tightening the screws on the CPU 3 Place the heatsink and fan on top of the CPU and fasten them with the reten tion bracket Figure 4 10 Placing the heatsink and fan on the CPU 27 PPC 175T User Manual 4 Fasten the four screws onto the CPU cooler module PPC 175T User Manual 28 4 5 Installing the DDR SDRAM Memory Module It is possible to install from 256 MB to 2 GB of DDR SDRAM memory The panel PC system provides two 184 pin DIMM Dual Inline Memory Module sockets and sup ports 2 5V DDR SD
17. are illustrated in Fig 4 1 4 2 4 3 and 4 4 1 Unscrew the side cover on the plastic HDD cover to expose the HDD module The Type II CF slot lies underneath the HDD module Figure 4 1 Unfastening the HDD side cover PPC 175T User Manual 22 2 Unfasten the screws securing the rear plastic cover and remove it ITE Figure 4 2 Unfastening the rear cover 3 Before removing the rear cover disconnect the system fan connector E WU a MIN a ANE UN Figure 4 3 Disconnecting the fan connector 23 PPC 175T User Manual Figure 4 4 The PPC without the Rear Cover 4 3 One enhanced Integrated Device Electronics IDE hard disk drive may be attached to the panel PC s internal controller which uses a PCI local bus interface The follow ing instructions are for installing the HDD 1 A metal plate holds the HDD to the upper right hand side of the metal shielding case See Fig 4 5 Fix the two screws on the metal plate of two side of HDD 2 Connect IDE cable from main board 3 Place the HDD on the metal plate and tighten the four screws from the bottom of the metal plate Figure 4 5 Fastening the HDD metal frame to the HDD PPC 175T User Manual 24 4 Plug the EIDE cable connector into the HDD m pe Figure 4 6 Plugging in the EIDE cable 5 Align the metal frame on the HDD to the mounting points and fasten the four screws 25 PPC 175T User Manual 4 4 Installing the Central Processing
18. chipset LAN Audio Touchscreen VGA USB light sensor utility and the light sen sor guide and a PDF copy of this user manual Note 1 The CD ROM drive is designated as D throughout this chapter 2 Enter means pressing the Enter key on the keyboard 5 6 2 Updating Driver Searching on the Advantech Website For further information about installing drivers on the PPC 175T and to access driver updates troubleshooting guides and FAQ lists visit the following web resources Advantech websites B www advantech com B www advantech com tw PPC 175T User Manual 38 Pin Assignments This chapter gives background information on the PPC 175T Sections include m MAN Heading01 style Arial Bold 18pt MAN H1 color Chapter 7 Pin Assignments 7 1 MAN Headingo01 style Arial Bold 18pt MAN H1 color MAN Body style Arial Unicode MS Regular 11pt Black These notes are for refer ence only Delete them before inserting new content 7 1 1 Heading02 style Arial Bold 14pt MAN H1 color 7 1 1 1 CompactFlash CN10 Table 7 1 MAN TableTitle style Arial Bold 12pt Black Pin Signal Pin Signal 1 DCD 2 RXD 3 TxD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI RI 5V 12V Figure 7 1 Test figure Figure 7 2 Another test figure Figure 7 3 A third test figure Note MAN Note table style Use it just like Caution and Warning tables Remember to add a TAB at the beginning then just select al
19. disk drives or floppy drives The table below lists the function of each of connectors Table 5 4 PPC 175T connectors table CN1 Serial port for touch CN21 x CN2 x CN22 Audio Jack CN3 Serial VGA port CN23 X CN4 Inverter power CN24 PS 2 2 CN5 LAN USB 2 CN25 X CN6 IDE HDD CN26 X CN7 Mini PCI CN27 x CN8 IDE Slim CD ROM CN28 X CN9 LVDS CN29 X CN10 X CN30 GPIO CN11 ATX power CN31 TYPE II CF slot CN12 LPT CN32 1394 port CN13 CPU fan CN33 1394 port CN14 X CN34 System FAN CN15 X CN35 COM 2 CN16 internal USB pin header CN36 2nd LAN CN17 internal Speakers CN37 Power Switch CN18 X CN38 Light sensor CN19 FDD CN39 LED 3 CN20 USB 2 CN40 x 35 PPC 175T User Manual Driver Installation This chapter gives information on installing drivers for the PPC 175T Sections include E Driver Installation E Updating Drivers Chapter 6 Driver Installation A Driver CD is supplied inside the accessory box Customers may need to use an external USB CD ROM related device to load the CD and install the drivers for the PPC 175T 6 1 Driver Installation Before installing the Ethernet driver note the procedures below It is necessary to know which operating system is installed on the PPC 175T Then refer to the corre sponding installation flow chart Follow the steps described in the flow chart to com plete the installation quickly Drivers and documents included on the CD are for the
20. e RI SEHR 5 Figure 1 1 Dimensions of PPC 175T sssessss 5 System Setup 8 A Quick Tour of the Panel PC ssssssseeeee 8 Figure 2 1 Front panel of PPC 175T ssssesses 8 Figure 2 2 Left side view of the panel PC 8 Figure 2 3 I O Peripheral Connectors Panel 9 Figure 2 4 Rear view of the panel PC u ee 9 Preparing for First time Use ssee 10 Installation Procedures ssem 10 2 3 1 Connecting the power cord sssseee 10 2 3 2 Connecting the keyboard and mouse 10 2 3 3 Switching on the power ssse 10 Running the BIOS Setup Program sess 10 Installing System Software uusuerssnneennessnnnnnnnnnnnnnnnnnnnnnnn 11 Installing the Drivers scssi noeneen 11 Figure 2 5 Drivers and Utilities on the CD ROM 11 Using the Panel PC 14 INTO UCION Em 14 CD ROM Drive optional oooonnnnccnnnnnnnccccnnnnnoconnnnncnanancnnncnana nos 14 Figure 3 1 Inserting and ejecting a CD ROM 14 PCMCIA concilio tbc an 15 Figure 3 2 Inserting and ejecting a PCMCIA card 15 PS 2 Mouse and Keyboard sese 15 PCI Bus Exparii n 1 iie rato rte eae e Ee ERR Ere ee aa Hon 16 Figure 3 3 PCI bus expansion sss 16
21. em with an HDD with an operating temperature rating of 50 C or above whenever the ambient temperature exceeds 35 C Touchscreen Analog resistive capacitive or Surface Acoustic Wave CD ROM drive Slim type 24X CD ROM or above DVD ROM drive Slim type 6X DVD ROM or above PCMCIA interface Complies with 1995 PCMCIA card standard Supports two PCMCIA card CardBus slots Two sockets support both a 16 bit PCMCIA card and a 32 bit CardBus simultaneously Hot insertion and removal CF Interface type II CF slot IDE interface for OS booting BW LAN 2nd 10 100 Bases LAN or Giga LAN are optional 3 PPC 175T User Manual 1 2 0 9 Environment B Temperature 0 45 C 32 122 F W Relative humidity 10 95 40 C non condensing W Shock 10 G peak acceleration 11 msec duration B Power MTBF gt 130 000hrs 1 2 0 10 Certifications m EMC CE FCC VCCI BSMI 3C m BSMI approved Safety CE UL CB PPC 175T User Manual 4 1 3 Dimensions 425 14 12 pu o a o 111 5 442 345 14 Figure 1 1 Dimensions of PPC 175T 5 PPC 175T User Manual System Setup This chapter gives system setup information for the PPC 175T Sections include B A Quick Tour E Installation Procedures B Running the BIOS Setup E installing System Software Chapter2 System Setup 2 1 A Quick Tour of the Panel PC Before starting to set up the panel PC take a moment to become familiar with the locations and purposes of co
22. erstellers ACHTUNG Es besteht die Explosionsgefahr falls die Batterie auf nicht fach m nnische Weise gewechselt wird Verfangen Sie die Batterie nur gleicher oder entsprechender Type wie vom Hersteller empfohlen Entsorgen Sie Batterien nach Anweisung des Herstellers Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000 betr gt 70dB A oder weiger Haftungsausschluss Die Bedienungsanleitungen wurden entsprechend der IEC 704 1 erstellt Advantech lehnt jegliche Verantwortung f r die Richtigkeit der in diesem Zusammenhang get tigten Aussagen ab PPC 175T User Manual viii Safety Precaution Static Electricity Follow these simple precautions to protect yourself from harm and the products from damage m To avoid electrical shock always disconnect the power from the PC chassis before working on it Don t touch any components on the CPU card or other cards while the PC is on m Disconnect power before making any configuration changes The sudden rush of power while connecting a jumper or installing a card may damage sensitive electronic components ix PPC 175T User Manual Contents Chapter Chapter Chapter Chapter 1 14 12 1 3 2 2 2 3 2 4 2 6 3 3 1 3 2 3 3 3 4 3 5 3 6 4 4 1 4 2 4 3 General Information 2 Introduction Em 2 SpecificatlONS 2 Table 1 1 Touchscreen specifications 3 DIMENSIONS m
23. g the Del key on your keyboard immediately after powering on the computer The settings specified with the setup program are recorded in a special area of mem ory called CMOS RAM This memory is backed up by a battery so that it will not be erased after turning off or resetting the system Whenever the power is turned on the system reads the settings stored in CMOS RAM and compares them to the equip ment check conducted during the power on self test POST If a problem occurs an error message will be displayed on screen and the computer prompts the user to run the setup program PPC 175T User Manual 10 2 5 Installing System Software Recent releases of operating systems from major vendors include setup programs which load automatically and guide you through hard disk formatting and operating system installation The guidelines below will help determine the steps necessary to install the operating system onto the panel PC hard drive Note Some distributors and system integrators may have already pre installed system software prior to shipment The BIOS of the panel PC supports system boot up directly from the CD ROM drive Alternatively it is possible to insert the system installation CD into the CD ROM drive To power on the panel PC or to reset the system press the Ctrl Alt Del keys simultaneously The panel PC will automatically load the operating system from the diskette or CD ROM If presented with a setup o
24. l PC and then turn on the panel PC 4 Referto the manual s which accompanied any serial device s for instructions on configuring the operating environment to recognize the device s 5 Run the BIOS setup program and configure the jumper settings to change the mode of the COM ports 2nd LAN or Giga LAN optional Line In Line Out Figure 3 4 I O ports 3 VGA Port An external VGA compatible device may be connected to the system through the 15 pin external port located on the bottom of the system unit The panel PC simultaneously supports an external CRT monitor in addition to the built in LCD display 1 Be sure the panel PC is turned off 2 Connect the external monitor to the system See Fig 3 4 3 Turn on the panel PC and the external monitor 3 8 USB Ports An external USB device may be connected to the system through the 4 pin USB ports located on the rear side of the system unit 1 Connect the external device to the system See Fig 3 4 2 The USB ports support hot plug in connection Install the device driver before using the device 17 PPC 175T User Manual 3 9 Audio Interface The audio interface includes three jacks Microphone in Line out and Line in See Fig 3 4 Their functions are Microphone in Use an external microphone to record voice and sound Line out Output audio to external devices such as speakers or earphones Line in Input audio from an external CD player or
25. l and con vert Table Convert To Table lH PPC 175T User Manual 40 Disassembly This chapter details a complete procedure for dissasembling the Panel PC Appendix A Disassembly A 1 Disassembly Procedure To completely disassemble the panel PC follow the step by step procedures below Users should be aware that Advantech Co Ltd takes no responsibility whatsoever for any problems or damage caused by disassembly of the panel PC by the user Warning Make sure the power cord of the panel PC is unplugged before starting T disassembly The following procedures do not include detailed assembly procedures for the CPU HDD CD ROM drive FDD and SDRAM Further details can be found in Chapter 4 1 Unfasten the HDD side cover Figure A 1 Unfastening the HDD side cover PPC 175T User Manual 42 2 Unfasten the rear cover and remove it bas 888 Figure A 2 Unfastening the rear cover 3 Before removing the rear cover disconnect the system fan connector E WU a MIN a A eec 1 n a iN LEN Figure A 3 Disconnecting the fan connector 43 PPC 175T User Manual 4 The PPC without the rear cover Figure A 4 The PPC without the rear cover 5 Remove the PCI riser card PPC 175T User Manual 44 6 Unfasten the middle plate S l a o Euer Figure A 6 Unfastening the middle plate 7 Remove the middle plate Figure A 7 Removing the middle plate 45 PPC 175T User Manual
26. m AnschluB an das Stromnetz die AnschluBwerte Verlegen Sie die NetzanschluBleitung so daB niemand dar ber fallen kann Es sollte auch nichts auf der Leitung abgestellt werden Alle Hinweise und Warnungen die sich am Ger ten befinden sind zu beachten Wird das Ger t ber einen l ngeren Zeitraum nicht benutzt sollten Sie es vom Stromnetz trennen Somit wird im Falle einer berspannung eine Besch digung vermieden Durch die L ftungs ffnungen d rfen niemals Gegenst nde oder Fl ssigkeiten in das Ger t gelangen Dies k nnte einen Brand bzw elektrischen Schlag aus l sen ffnen Sie niemals das Ger t Das Ger t darf aus Gr nden der elektrischen Sicherheit nur von authorisiertem Servicepersonal ge ffnet werden Wenn folgende Situationen auftreten ist das Ger t vom Stromnetz zu trennen und von einer qualifizierten Servicestelle zu berpr fen Netzkabel oder Netzstecker sind besch digt Fl ssigkeit ist in das Ger t eingedrungen Das Ger t war Feuchtigkeit ausgesetzt Wenn das Ger t nicht der Bedienungsanleitung entsprechend funktioniert oder Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen Das Ger t ist gefallen und oder das Geh use ist besch digt Wenn das Ger t deutliche Anzeichen eines Defektes aufweist VOSICHT Explisionsgefahr bei unsachgemaben Austausch der Batterie Ersatz nur durch densellben order einem vom Hersteller empfohlene mahnlichen Typ Entsorgung gebrauchter Batterien navh Angaben des H
27. nce 1 Warning A Visit the Advantech web site at www advantech com tocan find the latest infor mation about the product Contact the distributor sales representative or Advantech s customer service center for technical support and additional assistance Please have the following information ready before calling Product name and serial number Description of peripheral attachments Description of software operating system version application software etc A complete description of the problem The exact wording of any error messages Input voltage rated 100 240 VAC 50 60 Hz 4 A Use a 3 V 196 mA lithium battery Packing please carry the unit with both hands handle with care Maintenance to properly maintain and clean the surfaces use only approved products or clean with a dry applicator 5 CompactFlash Turn off power before insert ing or removing Com pactFlash storage card Rh 0D gt Contact information Our European representative Advantech Europe GmbH Kolberger Strafle 7 D 40599 Dusseldorf Germany Tel 49 211 97477350 Fax 49 211 97477300 PPC 175T User Manual vi Safety Instructions 1 Read these safety instructions carefully 2 Keep this User Manual for later reference 3 Disconnect this equipment from any AC outlet before cleaning Use a damp cloth Do not use liquid or spray detergents for cleaning 4 For plug in equipment the power outlet socket must be located near the equip
28. nd to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can iii PPC 175T User Manual radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Opera tion of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense FCC Class B Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installa tion This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful inter ference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interfer ence to radio or television reception which can be determined by turning the equip ment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reo
29. ng and ejecting a PCMCIA card 3 4 PS 2 Mouse and Keyboard To install a full size desktop PS 2 keyboard and mouse with the panel PC follow these instructions 1 Be sure the panel PC is turned off 2 Attach the keyboard to the purple colored 5 pin PS 2 port 3 Attach the PS 2 mouse to the green colored port 4 Turn on the panel PC 15 PPC 175T User Manual 3 5 PCI Bus Expansion The panel PC supports PCI bus expansion cards To integrate a new PClbus card into the system follow these instructions 1 OY eo N Turn off the panel PC Unscrew the eight screws on the top of the rear cover and remove it Remove the metal plate by unscrewing the single attaching screw Insert the PCI bus card into the PCI slot of the riser card See Fig 3 3 Run the setup program within the OS to configure the system Figure 3 3 PCI bus expansion PPC 175T User Manual 16 3 6 Serial COM Ports There are three serial COM ports on the bottom It is simple to attach a serial device to the panel PC like an external modem or mouse Follow these instructions 1 Be sure the panel PC and any other peripheral devices that are connected to the panel PC are turned off 2 Attach the interface cable of the serial device to the panel PC s serial port See Fig 3 4 If necessary attach the other end of the interface cable to the serial device Fasten any retaining screws 3 Turn on any other peripheral devices that is connected to the pane
30. ntrols drives connectors and ports which are illustrated in the figures below When placed upright on the desktop the front panel of the panel PC appears as shown in Figure 2 1 Light sensor LAN Power HDD Figure 2 1 Front panel of PPC 175T When viewed from the left side of the panel PC the CD ROM drive and PCMCIA expansion sockets are visible as shown in Fig 2 2 HDD Cover 1 CDR DVD Hole for Panel mount PCMCIA Speaker Figure 2 2 Left side view of the panel PC PPC 175T User Manual 8 Viewed from the bottom side the PCI expansion slot is located along with other IO on the bottom left side This slot is covered by a side panel cover The sunken I O section is at the bottom of the panel PC as shown in Fig 2 3 The I O section includes various I O ports including serial ports parallel port the Ethernet port USB ports the audio jacks and so on Power switch COM PCI card slot AC Inlet Mouse LAN Keyboard VGA USB 1394 Audio Jacks LAN or optional Giga LAN Figure 2 3 I O Peripheral Connectors Panel Both standard VESA standard 75 x 75 100 x 100 mm mounting sizes are supported so that customers may install different accessories for various applications
31. nything abnormal and list any onscreen messages when the problem occurs 2 Call your dealer and describe the problem Please have the manual product and any helpful information readily available 3 Ifthe product is diagnosed as defective obtain an RMA return merchandize authorization number from the dealer This allows Advantech to process the return more quickly 4 Carefully pack the defective product a fully completed Repair and Replacement Order Card and a photocopy proof of purchase date such as your sales receipt in a shippable container A product returned without proof of the purchase date is not eligible for warranty service 5 Write the RMA number visibly on the outside of the package and ship it prepaid to the dealer Declaration of Conformity CE This product has passed the CE test for environmental specifications when shielded cables are used for external wiring We recommend the use of shielded cables This kind of cable is available from Advantech Please contact your local supplier for ordering information CE This product has passed the CE test for environmental specifications Test conditions for passing included the equipment being operated within an industrial enclosure In order to protect the product from being damaged by ESD Electrostatic Discharge and EMI leakage we strongly recommend the use of CE compliant industrial enclo sure products FCC Class A Note This equipment has been tested and fou
32. pliant interface Multi stream Direct Sound and Direct Sound 3D acceleration W Stereo sound 18 bit full duplex codec W Audio interface Microphone in Line in Line out 1 2 0 5 Ethernet interface B Full compliance with IEEE 802 3u 100Base T and 10 Base T specifications Includes software drivers and boot ROM m Wake on LAN WOL and wake on USB support Wake on LAN USB function support for ATX power control 1 2 0 6 PCMCIA interface B Chipset RICOH R5C842 WB Cardbus controller A PC card controller offers a single chip solution as a bridge between the PCI bus and the Cardbus WB PCI bus interface Complies with PCI Local Bus Specification 2 1 and supports the 32 bit Cardbus Card 32 and the 16 bit PC card Card 16 without external buffers 1 2 0 7 Touchscreen specifications optional Table 1 1 Touchscreen specifications Type Analog Resistive Capacitive Surface Acoustic Wave SAW Resolution Continuous 1024 x 1024 4096 x 4096 Light Transmission 75 85 91 Controller RS 232 Interface COM4 Power Consumption 5 V 200mA 2 J 5V 100mA 5V 150mA Software Driver Supports both DOS and Windows Durability touches 35 million 225 million 50 million in a life time 1 2 0 8 Optional Modules m CPU Intel Pentium M or Celeron M processor up to 1 8 1 5 GHz W Memory Supports up to 2 GB DDR SDRAM 184 Pin mW HDD 2 5 IDE HDD Notices It is advisable that customers equip the syst
33. r installation program follow the instructions on screen The setup program guides the user through preparation of a new hard drive and installation of the new operating system If presented with an operating system command prompt such as E gt then partition and format the hard drive and manually copy the operating system files to it Refer to the operating system user manual for instructions on partitioning and formatting a hard drive 2 6 Installing the Drivers After installing your system software you will be able to set up the Chipset Ethernet VGA audio PCMCIA light sensor and touchscreen functions All the drivers are stored in a CD ROM disc entitled Drivers and Utilities the CD ROM can be found in your accessory box Audio Chipset LAN Light Sensor Touchscreen USB2 0 YGA Reccnsecsvecseed Figure 2 5 Drivers and Utilities on the CD ROM The various drivers and utilities in the CD ROM disc which help users install the driv ers and understand their functions These files are a very useful supplement to the information in this manual Note The drivers and utilities used for the PPC 175T panel PCs are subject to change without notice If in doubt check Advantech s website or contact ES our application engineers for the latest information regarding drivers and utilities 11 PPC 175T User Manual Using the Panel PC This chapter explains onboard devices and peripherial I O ports available on the PPC 175
34. rient or relocate the receiving antenna B Increase the separation between the equipment and receiver B Connect the equipment into an outlet on a circuit different from that to which the receiver is connected B Consult the dealer or an experienced radio TV technician for help FM This equipment has passed the FM certification According to the National Fire Pro tection Association work sites are classified into different classes divisions and groups based on hazard considerations This equipment is compliant with the speci fications of Class I Division 2 Groups A B C and D indoor hazards Technical Support and Assistance 1 Visit the Advantech web site at www advantech com support where you can find the latest information about the product 2 Contact your distributor sales representative or Advantech s customer service center for technical support if you need additional assistance Please have the following information ready before you call Product name and serial number Description of your peripheral attachments Description of your software operating system version application software etc A complete description of the problem The exact wording of any error messages PPC 175T User Manual iv Warnings Cautions and Notes Warning Warnings indicate conditions which if not observed can cause personal injury Caution Cautions are included to help you avoid damaging hardware or losing
35. sssssee 40 Disassembly 42 Disassembly Procedure sss enne 42 Figure A 1 Unfastening the HDD side cover 42 Figure A 2 Unfastening the rear cover 43 Figure A 3 Disconnecting the fan connector 43 Figure A 4 The PPC without the rear cover 44 Figure A 5 Removing the PCI riser card 44 Figure A 6 Unfastening the middle plate 45 Figure A 7 Removing the middle plate 45 Figure A 8 Unfastening the HDD module 46 Figure A 9 Removing the HDD nennen 46 Figure A 10 Disconnecting the HDD cable 47 Figure A 11 Loosening the screws on the HDD bracket 47 Figure A 12 Loosening the screws on the CD ROM module 48 Figure A 13 Pushing out the brace holding the CD ROM 48 Figure A 14 Removing the fixed brace 49 Figure A 15 Unfastening the CD ROM PCMCIA slot cover 49 Figure A 16 Removing the CD ROM PCMCIA slot cover 50 Figure A 17 Removing the CD ROM module 50 xii Appendix B Figure A 18 Disconnecting the CD ROM connector 51 Figure A 19 Removing the CPU module 51 Figure A 20 Unfastening the CPU socket
36. stening the CPU socket 21 Unfasten the screw on the CPU socket mounting plate and remove the CPU pua a E Figure A 21 Removing the CPU PPC 175T User Manual 52 22 Remove the SDRAM module m a re BR RR TRT a ran ERR Vii Figure A 22 Removing the gt SDRAM module 53 PPC 175T User Manual PCI Card Size Limits This chapter details the size limits for PCI cards that may be installed on the Panel PC motherboard Appendix B PCI Card Size Limits PCI Cards must be sized within the following dimensional limits 100 4 Figure B 1 PCI Card Dimensional Limits PPC 175T User Manual 56 Trusted ePlatform Services AD ANTECH Please verify specifications before quoting This guide is intended for reference purposes only All product specifications are subject to change without notice No part of this publication may be reproduced in any form or by any means electronic photocopying recording or otherwise without prior written permis sion of the publisher All brand and product names are trademarks or registered trademarks of their respective companies O Advantech Co Ltd 2006
37. t http www advantech com http www advantech com ppc B For technical support and service please visit our support website at http support advantech com This manual supports the PPC 175T Part No 2006175T00 Edition 1 Printed in Taiwan January 2008 PPC 175T User Manual ii Product Warranty 2 years Advantech warrants to you the original purchaser that each of its products will be free from defects in materials and workmanship for two years from the date of pur chase This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech or which have been subject to misuse abuse accident or improper installation Advantech assumes no liability under the terms of this warranty as a consequence of such events Because of Advantech s high quality control standards and rigorous testing most of our customers never need to use our repair service If an Advantech product is defec tive it will be repaired or replaced at no charge during the warranty period For out of warranty repairs you will be billed according to the cost of replacement materials service time and freight Please consult your dealer for more details If you think you have a defective product follow these steps 1 Collect all the information about the problem encountered For example CPU speed Advantech products used other hardware and software used etc Note a
Download Pdf Manuals
Related Search