ADTRAN 1184518L1 User's Manual
Contents
1. ADRAN CLEI VAUIAMBP __ Product P N 1442140G2 Small Form Factor Pluggable Gigabit Ethernet Single Fiber 40 km JOBAID Issue Date 0804 Document P N 61442140G2 22A DESCRIPTION The Small Form Factor Pluggable SFP Gigabit Ethernet Single Fiber is a bidirectional SFP that plugs into the Central Office Optical Network Unit ONU designed to accept SFPs The SFP provides a single optical interface to the GigE physical interface Installed into an appro priate ONU the SFP provides a Gigabit Ethernet tributary interface to the supporting system NOTE To ensure compatibility refer to the documentation provided with the ONU The following features are supported on the SFP 1000Base LX 1310 nm Transmitter 1000Base LX 1490 nm Receiver Optical distance 40 km maximum CAUTION Due to compliance certification requirements only SFPs supplied by ADTRAN should be used ADTRAN cannot certify system integrity with other SFPs Operational Specifications Optical Specifications Optical transmit level 2 dBm to 3 dBm Optical receive level 23 dBm to 3 dBm Optical connectors LC Extended Environmental Support Operational temperature range 40 C to 70 C Storage temperature range 40 C to 85 C Relative humidity to 95 noncondensing INSTALLATION To install the SFP into an appropriate module complete the following steps 1 Inspect the SFP If damaged file a claim with the carrie2. n battery return and frame ground the Warranty ADTRAN will replace or repair this product within the warranty period if it does not meet its published specifications or fails while in service Warranty information can be found online at www adtran com warranty 2008 ADTRAN Inc All Rights Reserved system would be intended for deployment only in a DC C installation The ADTRAN system chassis frame ground terminal must be connected to an earth ground to ensure that the metal enclosure of the SFP is properly grounded via the backplane connector NOTE The Gigabit Ethernet port s are optical and therefore are not classified as any type of port as defined in Appendix B of GR 1089 CORE Issue 4 The SFP is designed to meet the following environmental classes ETSI EN 300 019 1 1 Classification of environmental conditions Storage Class 1 2 ETSI EN 300 019 1 2 Classification of environmental conditions Transportation Class 2 3 ETSI EN 300 019 1 3 Classification of environmental conditions Stationary use at weather protected locations Class 3 3 The equipment is designed to function without degra dation during exposure to all test severities per Class 3 3 PRICING AND AVAILABILITY TECHNICAL SUPPORT 800 726 8663 RETURN FOR REPAIR 256 963 8722 61442140G6G62 22Ak 800 827 0807 CAUTIO SUBJECT TO ELECTROSTATIC DAMAGE JECREASE IN RELIABILITY HANDLING PRECAUTIONS REQUIRED
3. r and then contact ADTRAN Customer Service 2 Do not remove the protective end cap from the SFP until the fiber optic cable is ready to be connected 3 Insert the SFP into the SFP receptacle on the ONU Ensure the manufacturer s label on the SFP is facing upward for correct installation 4 Slide the SFP all the way into the receptacle until there is an audible click NOTE The latch on the SFP is used to remove the SFP from the cage on the circuit card 5 Continue the installation and turn up of the ONU using the instructions in the Job Aid that accompanied that ONU The Installation and Maintenance Practice I amp M for the ONU is available online at www adtran com ADRAN CLEI VAUIAMBP __ Product P N 1442140G2 Small Form Factor Pluggable Gigabit Ethernet Single Mode 40 km JOBAID Issue Date 0804 Document P N 61442140G2 22A COMPLIANCE CAUTION Electrostatic Discharge ESD can damage electronic modules When handling modules wear an antistatic discharge wrist strap to prevent damage to electronic components Place modules in antistatic packing material when transporting or storing When working on modules always place them on an approved antistatic mat that is electrically grounded The SFPis a Class 1 Laser Product and complies with the Laser Safety requirements of FDA 21CFR 1040 10 and 1040 11 and EN60825 1 and 2 The SFP is NRTL Listed and CB Certified to all applicable American and Eu
4. ropean safety standards The SFP is NRTL Listed to the applicable UL standards The SFP meets or exceeds all the applicable requirements of NEBS Telcordia GR 63 CORE and GR 1089 CORE The SFP is intended for deployment in Central Office type facilities EEEs EECs and locations where the NEC applies for example Customer Premises and is intended to be installed by trained service personnel Install the SFP in an ADTRAN product located in a restricted access location This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Changes or modifications not expressly approved by ADTRAN could void the user s authority to operate this equipment CAUTION Per GR 1089 CORE the ADTRAN system that the SFP is being deployed in is designed and intended for installation as part of a Common Bonding Network CBN The ADTRAN system that the SFP is being deployed in is not designed nor intended for installation as part of an Isolated Bonding Network IBN Per GR 1089 CORE Section 9 the SFP does not have an internal DC connection between battery return and frame ground The SFP can be installed in a DC I isolated or DC C common installation For installations where other cards or the host system have internal connections betwee
Download Pdf Manuals
Related Search