Addtron Technology P201 User's Manual
Contents
1. COMMERCIAL FLOOR CARE EQUIPMENT Standard and High Speed Floor Machines P201 P171 P131 175 RPM P201HD P171HD 175 RPM Standard Speed P202 P172 175 320 RPM Standard Speed Heavy Duty Dual Speed P203 P173 300 RPM P171SD 175 RPM High Speed Sander U S Patent Number 4 756 042 U S Patent Number 296 251 COMMERCIAL FLOOR CARE EQUIPMENT A Tacony Compan 3101 Wichita Court Wort in 76140 1710 X8444 P201 P171 P131 175 RPM P201HD P171HD 175 RPM P202 P172 175 320 RPM Standard Speed Standard Speed Heavy Duty Dual Speed P203 P173 300 RPM P171SD 175 RPM High Speed Sander Your new Powr Hite Foor Machine will afford you many years of trouble free operating satisfaction provided it is given proper care Prior to packaging your Powr Flite Floor Machine was inspected by a Quality Control Technician UNCRATING Your Powr Hite Hoor Machine was protectively packed to prevent damage in shipment We suggest that upon removing the unit from its carton you carefully inspect it for any possible damage in transit If damage is discovered immediately notify the transportation company who delivered your machine As a manu facturer we are unable to act upon any claim for concealed damage you must originate the claim IMPORTANT SAFEGUARDS This machine is designed to be safe when used to perform the functions specified in this Operator s Manual Should damage occur to electrical or mechani2. locked at the desired operating height and the electric cable plugged in place hands on the handle grips and squeeze the switch triggers beneath the handle grips See picture 3 This activates the motor and starts the block brush or attachment in operation CAUTION When leaving the machine unattended disconnect the wall plug and return the handle to the locked upright position to prevent accidental starting TO GUIDE YOUR FLOOR MACHINE To Right raise handle slightly The higher the handle is lifted the faster the machine will move to the right To Left to change direction lower the handle until the machine travels to the left The more the handle is lowered the faster the movement to the left TO INSTALL THE OPTIONAL SOLUTION TANK Mount the solution tank to the front of the handle and attach with mounting brackets and knobs Position the solution tank control handle horizontally and below the switch lever of the machine and adjacent to the right handle grip Remove the plug from the motor housing and insert the long extension tube adaptor and secure at bottom of machine with the retainer The solution tank should be used only with a showerfeed drive block or brush Picture 3 Switch Trigger APPLICATION OF THE HIGH SPEED 300 RPM FLOOR MACHINES MODELS P203 and P173 Spray Buffing to revitalize an existing floor finish to a wet look shine especially in heavy
3. TIONS OF 175 RPM STAN DARD SPEED FLOOR MACHINES ON CARPET e Bonnet cleaning with a Powr Sorb yarn bonnet and carpet maintainer chemical such as Spin Away Shampooing using a showerfeed shampoo brush and solution tank mounted to the hand containing carpet shampoo APPLICATION OF POWR FLITE HEAVY DUTY 175 RPM FLOOR MACHINES MODELS P201HD and P171HD The heavy duty standard speed floor machine may be used for spray buffing dry buffing scrubbing and stripping applications These heavy duty floor machines are specially recommended for long term aggressive scrubbing and stripping maintenance The P201HD amp P171HD heavy duty floor machines are specially recommended for the following applications Scraping with an attachment such as the Powr Flite Scrape Away tool to remove heavy industrial deposits and residue or to prepare a foundation for installation of carpet Wire brushing of concrete floors e Sanding with very aggressive sandpaper or sand screen discs Carpet restoration where shampooing amp pile lifting require very stiff brush bristles WARNING To prevent injury always remove the electrical plug from the electrical outlet before changing the polishing pad and before leaving the machine PREPARE THE MACHINE FOR OPERATION To attach the drive block or brush or other attachment be sure the handle is locked in the upright position See picture 1 Lay the floor machine on its back wi
4. ance when spray buffing Brown Spray Cleaner Pad Hoghair Blend Aggressive agent embedded in pad for unsurpassed cleaning Green Stripping Pad Hoghair Blend Heavy duty aggressive agent embedded throughout pad for removing old floor finish
5. cal parts the machine should be repaired by the manufacturer or competent service station before using in order to avoid further damage to the machine or physical injury to user Your floor machine is equipped with a safety switch lockout device designed for your safety Do not attempt to bypass or defeat the safety lockout device Never use any device to lock the power switch triggers in the ON position WARNINGS READ THIS OPERATOR S MANUAL WARNING You must have training in the operation of this machine before using it WARNING Machines can burn flammable materials and vapors Do not use this machine with or near fuels grain dust solvents thinners or other flammable materials WARNING Do not operate this machine unless it is completely assembled WARNING Do not use this machine as a step or to move furniture WARNING When disconnecting power cord from electrical outlet grasp the plug Pulling it out by the cord itself can damage cord insulation and internal connection to plug To prevent electric shock always remove the electrical plug from the electrical outlet before doing any repairs or maintenance to this machine WARNING To prevent injury always remove the electrical plug from the electrical outlet before changing the polishing pad and before leaving the machine WARNING To prevent injury keep hands feet and loose clothing away from the rotating pad WARNING Maintenance and repairs must be done by authorized personn
6. e receptacle is grounded Be sure to fasten the grounding tap to the faceplate screw e METAL SCREW COVER OF GROUNDED OUTLET BOX e A B GROUNDING PIN ADAPTER C GROUNDING lt MEANS ONE LAST REMINDER READ ALL INSTRUCTIONS WARNINGS AND CAUTIONS BEFORE USING EQUIPM ENT These guidelines are presented for your protection and convenience Please read them carefully since a failure to heed these precautions could result in discomfort or injury When using an electrical appliance basic safety precautions should always be followed WARNING TO AVOID FIRE DO NOT USE WITH A FLAMMABLE OR COMBUSTIBLE LIQUID TO CLEAN FLOOR COMMERCIAL FLOOR CARE EQUIPMENT A Tacon anan 3101 Wichita Court Ft Worth TX 76140 1710 X8444 2000 Tacony Inc All Rights Reserved miie PowrHD Pads The Finest Quality Heavy Duty Floor Pads Available Nylon Blend Thick Pads Polyester Blend Thick Pads Hoghair Pads All Thin Pads Packed 10 Pads Per Case All Thick Pads Packed 5 Pads Per Case Pads Sold By The Case Only Cases Can Be Assorted To Obtain Quantity Pricing Black Strip Pad Nylon Blend For heavy duty wet stripping Very aggressive agent embedded throughout pad Removes old wax build up Cleans down to original surface Brown Strip Pad Polyester Blend For heavy duty wet or dry stripping Very aggressive agent embedded throughout pad Removes old wax build up Cleans down to original surface G
7. el only WARNING Keep all fasteners tight Keep adjustments according to specifications WARNING Keep the electrical parts of the machine dry For storage keep the machine in a building WARNING Always use a three wire electrical system connected to the electrical ground For maximum protection against electric shock use a circuit that is protected by a ground fault circuit inter rupter Consult with your electrical contractor WARNING To prevent damage to the power cord do not let the pad pad driver or wheels touch the power cord when the machine is running Always lift the power cord over the machine WARNING Make sure all labels decals warning cautions and instructions are fastened to the machine APPLICATIONS FOR FLOOR MACHINE MODELS P201 P171 P201HD P171HD and P131 175 RPM ONLY The Powr Flite 175 RPM floor machine will operate in a wide variety of applications The 175 RPM floor machine is the most versatile speed in the floor care industry APPLICATIONS OF 175 RPM STANDARD SPEED FLOOR MACHINES ON HARD FLOORS Spray buffing with a Powr HD red spray buff pad and spray buff chemical such as Powr Glo Dry buffing a buffable finish with a Powr HD tan beige or white pad or Powr Luster brush Scrubbing with a Powr HD green or blue pad or scrubbing brush such as Powr Scuff Stripping with a Powr HD black pad and a stripping chemi cal such as Powr Up APPLICA
8. ngth Unplug anything other than the machine from the circuit or locate another circuit Machine will not start Circuit breaker is not reset Reset breaker Plug is broken or has a loose contact Replace Circuit breaker is defective or weak Replace Switch is defective Replace switch Rectifier is defective Replace rectifier P202 and P172 only Machine will not reach operating speed Unplug anything else other than the machine from the circuit or locate another circuit Motor runs but pad or brush does not turn Coupling is broken Replace Coupling is not covered under war ranty Do not attempt to place a running machine over a block or brush Always place and remove the block or brush by hand SAFETY INSTRUCTIONS This Floor Machine should be grounded while in use to protect the operator from electric shock This machine is equipped with a 3 conductor cord and a 3 prong grounded type attachment cap plug to fit the proper grounding type receptacle The green or green and yellow conductor in the cord is the grounding wire Never connect this wire to anything other than the grounding blade The Hoor Machine is provided with an attachment cap plug as shown in Sketch A and is intended for use on a nominal 120 volt circuit If a properly grounded receptacle as shown in Sketch A is unavailable an adaptor as shown in Sketch C is available and should be installed as shown in Sketch B if the outlet box that houses th
9. pray buff at low speed with an open weave pad such as the Powr HD blue cleaner pad or the brown hoghair blend spray cleaner pad Remove the spray cleaning pad and place a buffing pad on the machine such as Powr HD yellow beige or natural hoghair blend pads Switch the speed to High 320 RPM and buff the dulled finish to a high gloss Unplug the power cord and wrap it under the cord hook and over the right handle grip Clean the cord off to prevent heaw soiling and cleaning residues from building up on the cord This is a good time to inspect the cord for cuts gashes and loose prongs Tip the machine back and remove the pad and the drive block or brush The condition of the floor pad or brush has a direct affect on the performance of your floor machine When the pad becomes dirty turn it over and use the other side When finished wash the pad or brush and allow it to dry completely before using it again Stand the wet brush on the bristles until dry then hang up the brush Do not store the machine with the drive block pad or brush on the machine Wipe off the machine housing and wheels to prevent build up of unnecessary residue TRANSPORTING THE MACHINE Place the handle in the upright position Lock the handle cam release lever Tip the machine back and transport on the wheels MAINTENANCE FOR THE P201 P203 P171 P173 P131 P201HD P171HD P202 and P172 Once a month remove the motor cover ofthe unplugged machine by p
10. reen Scrub Pad Nylon Blend For heavy duty scrubbing or light stripping wet or spray Aggressive agent embedded throughout pad Removes heaw dirt and scuff marks without removing waxed finish Blue Cleaner Pad Polyester Blend For heavy duty scrubbing or light stripping wet or spray Aggressive agent embedded throughout pad Removes heavy dirt and scuff marks without removing waxed finish Tan Buff Pad Nylon Blend For buffing and light wet scrubbing Mild aggressive agent embedded throughout pad Removes light scuff marks and dirt while producing a smooth shining finish Red Spray Buff Pad Polyester Blend For spray buffing and light scrubbing Mild aggressive agent embedded throughout pad Removes light scuff marks and dirt while producing a smooth shining finish Yellow High Speed Spray Buff Pad Polyester Blend For spray buffing when using a high speed buffing machine light aggressive agent in pad Specially designed for use with high speed floor machines for an extra high gloss finish Beige Ultra High Speed Spray Buff Pad Polyester Blend Specially designed when using an ultra high speed floor machine 1200 to 2000 RPM Mild aggressive agent in pad for light cleaning and super polishing White Super Polish Pad Polyester Blend For polishing No aggressive agent in pad Extra fine pad for producing high luster finish Natural High Speed Spray Buff Pad Hoghair Blend Produces a wet look shine of unequaled brilli
11. th the handle lying on the floor this exposes the driving plate on the underside of the floor machine Holding the drive block brush or attachment in both hands and straddling the motor with your back to the handlebox bend over and fit the three slots of the clutch plate build into the back of the brush over the three lugs of the driving plate Turn the drive block brush or attachment counter clockwise as far as it will go until it is seated in the ready to use position See picture 2 CAUTION This is the only proper way to install a drive block brush or attachment NEVER put a drive block brush or attach ment on the machine by placing it on the floor and moving the running machine over it or by placing the machine over the block or attachment and then starting the motor Return the floor machine to upright position and adjust handle to operating position Recommended handle position is close to the waist with arms extended down Lock the cam release lever into position NOTE The hardened steel cam release lever does not require extreme tightening to effectively hold the handle in position Over tightening will shorten the functional life of the lever To remove drive block brush or attachment Lay the floor machine on it s back again and disengage clutch plate slots from driving plate lugs by turning clockwise HOW TO OPERATE THE MACHINE With the drive block and pad brush or attachmentin the ready to use position the handle
12. traffic areas using a Pow HD yellow or natural hoghair blend pad Dry Buffing with a brush on uneven floors coated with a buffable a or with a Powr HD tan beige or white pad on even floor surfaces OPERATIONS OF THE HIGH SPEED 300 RPM MODELS P203 and P172 Follow the same operation procedures described for 175 RPM machines APPLICATION OF THE DUAL SPEED 175 320 RPM MACHINES MODELS P202 and P172 The Powr Hite dual speed machines will operate in a broad range of applications These machines perform all the applications of the 175 RPM standard speed machines and the 300 RPM high speed machines except the specialized applications Do not use dual speed machines for sanding grinding or scraping The dual speed machines are specially designed for spray cleaning of heavy traffic areas OPERATION OF THE DUAL SPEED MACHINES Follow the operation procedures described for 175 RPM machines The proper speed selection is important to properly operate these machines Speed selection Low 175 RPM or High 320 RPM is made with the switch located on the base and motor housing See Picture 4 Stripping scrubbing bonnet cleaning and shampooing should be performed at 175 RPM Low Speed Spray buffing and dry buffing should be performed at 320 RPM High Speed Spray cleaning is a two speed maintenance operation Apply a spray buff chemical such as Powr Glo to the floor ahead of the machine Make the first passes through the s
13. ulling evenly but firmly with both hands until the cover is removed Vacuum outany dustor debris which has accumulated on the motor Replace the motor cover by setting it over the holes in the hous ing and firmly pushing it down Check and maintain the tightness of all the fasteners WARNING Do not overtighten the switch housing screws Picture 4 Speed Switch Keep the machine clean especially at the handle tube and collar so the handle tube will move freely through the collar Inspect the cord for cuts gashes or loose prongs replace as needed Disassembly of this motor voids the warranty Improper disassembly and assembly of this motor can permanently damage the field or rotor For P202 amp P172 only The length ofthe carbon brushes should be inspected annually If they are no longer extended past the hold er window they should be replaced Replacement of the carbon brushes should only be done by a qualified service technician TROUBLESHOOTING Machine does not run The circuit breaker has tripped Allow the circuit breaker 2 minutes to cool before resetting Plug is broken or has loose contact Replace Prevent circuit overload Check the pad and change it if it is rough or dirty Spray buffing or spray cleaning is not a substitute for scrubbing or mopping a floor Prepare the floor surface before spray buffing Eliminate any extension cord that is smaller than 12 3 wire or greater than 25 feet in le
Download Pdf Manuals
Related Search