Acura 08B26-S3V-2000-91 User's Manual
Contents
1. WS Ia ane M BII 24550 INSTALLATION CD CHANGER 2003 MDX INSTRUCTIONS ATTACHMENT KIT PARTS LIST CD Changer Attachment Kit ea an P N 08B26 S3V 200 Right base bracket 4 Washer screws 4 x 8 mm S 2 Wire clips CD Changer sold separately P N 08A26 1B2 101 BUS Cable ED CD changer ie T Left base bracket 4 Flange bolts 6 x 12 mm 4 Washer screws 4 x 6 mm Not used 4 Flange nuts Adhesive seal sheet Locking covers IF Right changer bracket CD magazine Owner s Manual CP Small wire tie Not used Black cushion tape d Left changer bracket 2 Gray cushion tapes 2002 American Honda Motor Co Inc All Rights Reserved BII 24550 0209 08B26 S3V 2000 91 1 of 7 TOOLS AND SUPPLIES REQUIRED Flat tip screwdriver Phillips screwdriver Ratchet 8 mm 10 mm and 12 mm Sockets Shop towel Diagonal cutters 8 mm and 10 mm Combination wrenches INSTALLATION Customer Information The information in this installation instruction is intended for use only by skilled technicians who have the proper tools equipment and training to correctly and safely add equipment to your vehicle These procedures should not be attempted by do it yourselfers 1 Make sure you have the anti theft code for the radio then write down the frequencies for the preset buttons 2 Disconnect the negative cable from the battery 3 Using a flat tip screwdriver wrapped with a shop towel pry up2. cushion tape Fold the cushion tape around the CD changer bracket Position the CD changer on the base brackets and tighten the four 6 x 12 mm flange bolts you installed in step 14 Install the four flange nuts on the ends of the studs that extend from the base brackets and tighten them securely Tighten the four 6 x 12 mm flange bolts you removed in step 14 24 Connect the BUS cable connector to the CD changer connector BUS CABLE CD CHANGER 25 Plug the BUS cable connector the vehicle harness connector and the antenna lead into the rear of the audio unit VEHICLE HARNESS ANTENNA LEAD SCREW 26 Check that all wire harnesses are routed properly and all connectors are plugged in 27 Connect the negative cable to the battery Enter the customer s radio anti theft code and reset the radio station presets 28 Check that the radio and the CD changer work according to the appropriate owner s manual BII 24550 0209 2002 American Honda Motor Co Inc All Rights Reserved 29 30 31 32 2002 American Honda Motor Co Inc All Rights Reserved NOTE Whenever the battery is disconnected the driver s window AUTO function is disabled Start the engine Push down on the driver s window switch until the window is fully open Pull up on the driver s switch to close the window completely then hold the switch for 2 seconds Lower and raise the driver s window to check the ope
3. adjusting pins are not in the horizontal H position move the pins to the horizontal H position by sliding them up with an awl SPRING ADJUSTING PIN LEFT LOCKING COVER included with CD Changer kit RIGHT LOCKING O COVER included SPRING with CD ADJUSTING PIN Changer H Horizontal kit Remove the adhesive backing from the L and R locking covers and attach them to the sides of the CD changer Align the diagonally opposite holes with the H and V positions 2002 American Honda Motor Co Inc All Rights Reserved BII 24550 0209 18 Install the right changer bracket on the CD changer using two 4 x 8 mm washer screws and the two wire clips Install the left changer bracket on the CD changer using two 4 x 8 mm washer screws NOTE With the changer mounted in this location the locking covers do not indicate right and left correctly Mount the CD changer brackets in the direction shown LEFT CHANGER BRACKET RIGHT CHANGER BRACKET CLIP 5of7 19 20 21 22 23 6of7 Attach one gray cushion tape to the rear of the CD changer leaving half of the cushion tape extended past the CD changer Using scissors cut the cushion tape at the end of the CD changer Fold the ends down around the edges of the CD changer RIGHT BASE BRACKET LEFT BASE BRACKET FLANGE NUT CUSHION TAPE Attach the other gray cushion tape to the CD changer overlapping the other
4. er console and the driver s seat 2002 American Honda Motor Co Inc All Rights Reserved BII 24550 0209 3 of 7 11 Atthe radio opening adjust the BUS cable so it s the same length as the vehicle harness Make the BUS cable and vehicle harness are the same length VEHICLE HARNESS ae WIRE TIE G Tal WIRE TIE BLACK CUSHION TAPE BUS CABLE Secure the BUS cable to the vehicle harness with three wire ties in the areas shown 12 Attach the black cushion tape at the edge of the center console in the area shown 13 4 of 7 BII 24550 0209 Install the right and left base brackets into the holes in the driver s seat risers and install two 6 x 12 mm flange bolts into each bracket Do not tighten the bolts yet 6 x 12 mm FLANGE BOLTS 4 a T YZ 9 4 Zag LE R 4 E ee OL rey RIGHT LEFT Yei i BASE BASE 2 a BRACKET BRACKET 2002 American Honda Motor Co Inc All Rights Reserved Installing the CD Changer 15 Carefully unpack the CD changer Remove the three shipping clips and discard the shipping cover Install an adhesive seal included with the CD changer kit over each of the three clips holes Save the shipping clips for your customer in the event the unit needs to be serviced SHIPPING CLIPS 3 SHIPPING COVER Discard SHIPPING SEALS 3 16 Visually check the position of the spring adjusting pin on both sides of the CD changer If the spring
5. on the clips and pull the radio panel out toward you Unplug the connectors and remove the radio panel CLIP 2 of 7 BII 24550 0209 4 Remove the screws fastening the audio brackets then pull the audio unit out toward you Unplug the vehicle connectors and antenna lead from the rear of the audio unit VEHICLE HARNESS ANTENNA LEAD RADIO BRACKET SCREW 5 On the driver s side of the vehicle gently pull the center console lower cover out toward you to release the clips and remove the center console lower cover Take care not to damage the clips DRIVER S CENTER CONSOLE LOWER COVER CLIP 2002 American Honda Motor Co Inc All Rights Reserved 6 Remove the driver s seat front cover by pulling it toward you Take care not to damage the clips DRIVER S CG E SS DRIVER S SEAT FRONT COVER CLIP 7 Route one end of the BUS cable from the radio opening down through the center console FRAME VEHICLE HARNESS BUS CABLE 14 PIN RADIO CONNECTOR OPENING 9 Locate the slit in the floor carpet just under the driver s seat cushion and pull the BUS cable 14 pin connector out about 300 mm through the slit SLIT in FLOOR CARPET BUS CABLE DRIVER S SEAT 10 Secure the BUS cable to the vehicle harness with a wire tie in the area shown BUS CABLE WIRE TIE VEHICLE HARNESS BUS CABLE ABE BUS CABLE 8 Continue routing the BUS cable along the cent
6. ration of the driver s window AUTO function Do the PCM idle learn procedure Make sure all electrical items are turned off Start the engine Hold the engine speed at 3 000 rom with no load in Park or Neutral until the radiator fan comes on Letthe engine idle for about 5 minutes with the throttle fully closed and with all electrical items off NOTE If the radiator fan comes on during this step the time when it is operating must not be included in the 5 minutes BII 24550 0209 7 of 7
Download Pdf Manuals
Related Search