8x8 BPG510 Owner's Manual
Contents
1. Empty Log Empty Log Update Page 24 of 27 8x8 Inc 2005 BPG510 User Interface Guide Handset Configuration This section is to configure your connected analog telephone handset to command advanced features Handset Configuration Enable Simple Flash Key Setting O Complex Key Settings Advanced feature commands HoldfUnhold fl Alternate i Conference Tr Drop Conference fe NOTE Fior Tis a Flash Hook fe g fi Flash F4 save Handset Settings Enable Simple Key Setting Select this setting if you just want to enable simple key setting to your connected handset Complex Key Settings Advanced feature commands Select this setting if you want your connected telephone handset to use the following feature Press Flash and then 1 on your connected telephone key pad for Hold Unhold command Press Flash and then on your connected telephone key pad for Alternate command Press Flash and then 7 on your connected telephone key pad for Conference command Press Flash and then 8 on your connected telephone key pad for Drop Conference command 8x8 Inc 2005 Page 25 of 27 BPG510 User Interface Guide Upgrade Firmware Menu Upgrade Firmware Warning The firmware upgrade process will reset the unit into the upgrader mode This will terminate all network connections and reset your browser connection Filename Start Firmware Upgrade Upgra2. Dynamic Routing Dynamic routing allows the BPG510 to learn routing tables from other network devices by means of the Routing Information Protocol RIP With RIP network devices can broadcast messages containing information on the status of network connections RX Mode means we listen to and process RIP messages TX Mode means we send RIP information to other routers RX Mode select ENABLED to have the BPG510 process any RIP messages it receives from other network devices Select DISABLED to have the BPG510 ignore any RIP messages it receives TX Mode Select ENABLED to have the BPG510 broadcast RIP messages to other network devices Select DISABLED to prevent the BPG510 from broadcasting RIP messages Static Routing Static routing lets you configure particular IP addresses to be routed to the LAN port or the WAN port of the adapter Subnet Mask Enter the subnet mask of the destination device Page 18 of 27 8x8 Inc 2005 BPG510 User Interface Guide Gateway IP Enter the IP address of the gateway i e the next router in the network path to the destination device Destination IP Address Enter the IP address of the device you want to configure static routing for Any Ethernet packets destined for this IP address will be routed according to this configuration Metric Enter the metric associated with this static route The Metric field corresponds roughly to the number of hops it takes to get to the network or host b
3. are not sure leave this blank 7 Click SAVE PPPOE SETTINGS 8x8 Inc 2005 Page 7 of 27 BPG510 User Interface Guide Connecting Local Computers Connecting a single computer If you want to connect a single computer to the Internet through your BPG510 use a standard CAT5 Ethernet cable to connect the BPG510 s LAN port to your computer s Ethernet port You may have to reboot your computer after you connect it to the phone but no other configuration should be necessary Connecting a local network lf you have more than one device you want to connect to the Internet then you will need to use an intermediary device such as a switch a router or a wireless access point We strongly recommend that you connect your BPG510 directly to your broadband modem and connect your switch router or access point to the LAN port of your phone The BPG510 performs essential Quality of Service QoS function that allows for superior voice quality Placing any other device between the BPG510 and your broadband modem may reduce the quality of your VoIP phone calls due to the traffic on your network Supporting a host server on the local network port forwarding If you plan to set up a computer on your local network to host files or programs accessible to the Internet you will need to configure your BPG510 to forward the data associated with the specific type of service you want to support such as a web server an FTP server game server etc
4. You can configured the phone using the same web browser you use to surf the Internet To open your phone s configuration utility follow these instructions 1 Connect a computer with a web browser directly to the LAN port of your BPG510 You may be able to connect to the BPG510 through a router or wireless access point but if you have any difficulty connecting try connecting directly to BPG510 s LAN Ethernet port 2 Be sure that this computer is configured to dynamically get an IP address e g has the DHCP client enabled 3 Type the IP address of your BPG510 s into the address bar of your web browser The default IP address of your BPG510 is 192 168 88 1 Then press the ENTER key You will be prompted to enter a password the default password is admin gt Note If you change the LAN IP address of your phone be sure to make note of it 4 You should now see the your BPG510 s System Information Screen PacketS BPG510 Broadband Phone Gateway LAN Welcome to the BPG510 Broadband Phone Gateway configuration utility Select from the configuration options in the menu on the left Home System Upgrade Firmware System Information Reset System Uptime 0days 3h 51m 44s LAN IF Address 192 168 1 1 Static LAM MAC Address 00 17 76 0c 7fb3 WAM IF Address 192 168 15 100 Dynamic WAN MAG Address 00 1 1 f6 0 7fb3 SIF Server 192 84 16 30 175062 Security Mo password installed Application Code wersi
5. PacketS Broadband Phone Gateway BPG510 Technical Users Guide Firmware version 0 14 1 and later Revision 1 0 2006 8x8 Inc BPG510 User Interface Guide Table of Contents About your Broadband Phone Gateway BPG510 cscssseseeeeeneeeneeseneees 4 Opening the BPG510 s Configuration Utility cc teseeeeeseeeseneeeeeseeeeneeeeeneeneaes 4 Connecting to Your Broadband Modeim ccsssccceeseeceeseeceeseecenseeeensesenneeseaes 6 5S UNICO WEY MOT Gir acececcice ct caged E TE 6 Setting up With PPPOE cecccceccccceececceeeeeeee cesses eesaeeeeseeesseeeeseeeessaeeessaeeesaeees 7 Connecting Local Computers wiceciceccincscesscecccnswcasaceccsncacesssecovarscavauesaxeceveseessassceuns 7 Connecting a single COMPUTES cccccceececceeeeceeeeeeeeeeesseeeesseeesaeeeessaeeesaeeeeeaaeess 8 GOMMECIIIG a IOCANNOIW ONG aici aec stern eeenscaapenseseeyeestacecccarsciaeesaiandoashasasnasaaesolaesuaieaen 8 Supporting a host server on the local network port forwarding 0 ccseeeee 8 SPUNI Ua DMZ serrer EEEE ERENER E A 9 Detailed Sereen RErGrONGE icccetececweucecercsetecesecetesesveetecesasecvsesnwesuseausearscesunsneenneccnse 11 AAT ASE a O OEO E A EE N A T E EO E N EE 11 WAN AUS nee eee E S E E E ee eee 11 WAN Configuration ccccccccccsecceceeeeeceeeeeseeeeeseecesseeeeesaeeesseeeesseeesaeeesaneeeeas 12 PPPOE e ee eee 13 MAG GI OMIA oats cte cscs erssieerseepecetscrveiciseteere a
6. ame Save WAN Settings 4 Select the radio button labeled OBTAIN WAN CONFIGURATION DYNAMICALLY 5 Click SAVE WAN SETTINGS Page 6 of 27 8x8 Inc 2005 BPG510 User Interface Guide Setting up with PPPoE Point to Point Protocol over Ethernet PPPoE is often used by DSL broadband providers to connect and authenticate users on their networks The service provider will give you a user name and password and usually some additional software you need to run in order to go online The BPG510 can take the place of the additional PPPoE software allowing you to establish and maintain your broadband connection without running any extra programs on your computer Follow the steps below to configure the BPG510 to use a PPPoE based connection 1 Open the configuration utility 2 Inthe menu bar down the left side of the screen select WAN 3 Inthe menu bar on the top of the screen select PPPoE This opens the WAN PPPoE Configuration screen WAN PPPoE Configuration Enable PPPoE No be Authentication Username Password Settings Service Mame AC Mame Save PPPOE Settings 4 Under ENABLE PPPOE click the drop down arrow and select YES 5 Under AUTHENTICATION enter the USERNAME and PASSWORD that were provided by your ISP Username and password are often case sensitive so be sure enter capital and small letters correctly 6 Under SETTINGS enter the SERVICE NAME and AC NAME required by your ISP If you
7. des will automatically be performed by your BPG510 periodically as upgrades become available This feature is included to allow packet8 upgrading options for future product enhancement CAUTION The Upgrade Firmware process will reset the unit into the Upgrade Firmware mode This will terminate all network connections and reset your browser connection The Upgrade Firmware screen is used to update the firmware in your BPG510 You should not use the Upgrade Firmware screen except on the advice of a Customer Service Representative Page 26 of 27 8x8 Inc 2005 BPG510 User Interface Guide RESET Menu Reset Warning Resetting the system will terminate all network connections and reset your browser connection Reset and execute Main Application Reset and execute Downloader Application Reset CAUTION Resetting the system will terminate all network connections and reset your browser connection Reset and execute Main Application Select this option to reset the BPG510 Reset and Execute Downloader Application Select this option to have the BPG510 reset and automatically go into the Upgrade Firmware mode CAUTION Resetting into the Upgrade Firmware mode will terminate all network connections and reset your browser connection You should not use the Reset and Execute Downloader Application option except on the advice of a Customer Service Representative 8x8 Inc 2005 Page 27 of 27
8. e data sent to 8 Click ADD The BPG510 will add this port range to list of forwarded ports 9 Repeat steps 5 through 8 for any additional ports ranges you want to forward To remove any port ranges from the list of forwarded ports click the REMOVE button beside the port range you want to delete Setting up a DMZ lf you want to have one computer on your network receive all un forwarded data that arrives at your firewall for instance because you want to monitor network traffic on the WAN side or you have one computer running too many services to configure all the forwarded ports you can establish a single computer as a DMZ Any data that is not in a port forwarding range will be sent to the DMZ Follow the steps below to configure a computer as a DMZ 8x8 Inc 2005 Page 9 of 27 BPG510 User Interface Guide CAUTION The BPG510 cannot protect a computer running as a DMZ from malicious access Any computer running as a DMZ should be running a PC based firewall I Traffic sent to the DMZ is still subject to translation by NAT This means that applications that are damaged by NAT will still be affected 1 Open the configuration utility 2 Inthe menu bar down the left side of the screen select LAWN 3 In the menu bar across the top of the screen select DMZ This will open the DMZ Host Configuration screen DMZ Host Configuration OM Host IF Address 192 168 1 Save DMZ Host Configuration 4 Enter the IP address o
9. earsesearse ua weeicme ESE EES EE 13 EAN MODO secre dese ae EE EEEE EEEIEE EEE EEEE sete denesetancsencaeteas 14 LAN CONN AU Oeste sates aE 14 NIG GIGAUrA DIO a E E E S 16 Roul COMPO ATO seres erener ENEE EN 18 DYN ROUMINIG eaea EEE 18 Static Routing cccceccccseececeeeeecaeeeeceeeceeeeeeeseeeeessaeeeseeeeeseeeeesaeeeeseeeesseeeersneees 18 PO FOWAO eceran EEE RE E EREE ERSS 19 Filtering Configuration srcens ct sacvcnctdedeenssedesetdedeeactdedecechcacseratdedenadeeecrctececect tees 20 DMZ Host Configuration ccccccecccceesceeeeeeeceeeeeseeeeeseeesseeseeseeeesseeeesseeeesaaes 21 oy Go Bt rsr eee ee ee 22 Set Security Password 0 ccccceeccsceeessceeeesceeeecceeeesceeeesceeeesceeeescaeesceesesceeess 22 UO CAN AO Nara eracepaeicieceariecineeecjareqeciediaceemeiateninenniadiadeesindedeeauiedenicemmediaceamendindeamcedenisaneeenerehean 22 SMEO e nee ne enn ee ene ner nee nen nee eee oe ee ere 23 La WOO EEEE E EA A E EA E 24 Handset connguratlO M orsssessrer eaa E E EEEN ENEA 24 Upgrade Firmware Menu cc ccccsscccsseccceecceececeuceceusecsucecsucessueessueessueenensensees 26 RESET Menu cccccccceccceeecsececeeceueeeeceseeeceeeeeuceseeeseueeseeseesauessueeseeteueseeesees 27 Page 2 of 27 8x8 Inc 2005 BPG510 User Interface Guide About your Broadband Phone Gateway BPG510 1 Power The Power light is solid green when the power is on 2 Service The Service light is solid green wh
10. eing entered Interface Select LAN to route packets destined for this device to the LAN port Select WAN to route packets destined for this device to the WAN port Port Forwarding The Internet uses ports to specify different types of service requests For instance an email message contains a code for port 110 POP3 mail services while a web page request contains a code for port 80 HT TP services This allows the router to send the requests to the correct host any marked as port 110 is routed to the mail server and any data marked as port 80 is routed to the web server lf you want to set up one or more computers as a host you must tell the router what services should be sent to that host This configuration is called port forwarding There are over four thousand ports defined for different services Of these about one thousand are used most often and considered well known ports Complete lists of all well known ports are available on the Internet search for well known ports 8x8 Inc 2005 Page 19 of 27 BPG510 User Interface Guide Port Forwarding Configuration Reserved Ports The following ports have been reserved by the CPE and may not be forwarded to the LAN 68 44655 2000 8019 Port Forwarding to LAN Part Range Protocol l Destination Address L Both 192 166 1 Add Reserved Ports The adaptor reserves ports 5060 5061 and 10000 10015 Port Forwarding to LAN PORT RANGE Enter the first and last number
11. en you are authenticated with Packet8 3 WAN The WAN light is green to indicate that your modem is connected properly to the Internet It blinks rapidly when information is being sent over the port between BPG510 and the modem 4 LAN The LAN light is green when a PC or other networking device is connected to the BPG510 with a network cable 5 Line The Line light is green when you go off hook to indicate that your BPG510 is ready to make a call 6 Message The Message light is green when you have a message waiting in your mailbox REAR picture 1 Power Jack Connect the included power cord to this jack 2 Reset Switch The Reset button is used in rare cases when the BPG510 may function improperly Resetting the BPG510 will restore the BPG510 s normal operation while maintaining the programmed settings We recommend you consult a Packet8 customer service representative before using this button 3 WAN The WAN port is for connection to your cable or DSL modem or to connect to your existing router 4 LAN The LAN port is for connection to your computer or other networking device 5 Line The Line port is for connection to your telephone handset Use the telephone cable to connect the telephone to this port 8x8 Inc 2005 Page 3 of 27 BPG510 User Interface Guide Opening the BPG510 s Configuration Utilit Your BPG510 VolP phone provides a browser based configuration utility
12. ere the BPG510 is currently operating Adjust clock for daylight savings select this box to have the BPG510 automatically adjust the time one hour for Daylight Standard Time DST If your area does not observe DST do not enable this option Call Log The Call Log displays the last 10 calls received or transmitted by the BPG510 Call Log Last 10 calls DateTime Line FO Number Call lD Audio RTP statistics MOTE This call log is temporary and will be lost if the UIPTS66P is rebooted Update DATE TIME Displays the date and time of the call LINE Displays the line the call used I O Displays whether the call was inbound our outbound NUMBER Displays the phone number of the other party to the call CALL ID Displays the Call ld header value in the SIP messages Your service provider 8x8 Inc 2005 Page 23 of 27 BPG510 User Interface Guide uses this information to locate manage calls during troubleshooting AuDIO RTP Displays RTP RTCP statistics for the call e g the number and percentage of STATISTICS lost packets jitter latency etc Error Log The error log screen is used for gathering diagnostic information that could be used later by a Packet8 technician to help investigate a network problem or a disruption of service This screen will be needed if you call Packet8 customer support system Error Log Empty Log Empty Log Empty Log Empty Log Empty Log Empty Log Empty Log Empty Log
13. evice controlling IP address assignments on your local network you may need to change the BPG510 s local IP address to place it on the same network and subnet Page 14 of 27 8x8 Inc 2005 BPG510 User Interface Guide LAN Configuration Network Settings IF Address 192 166 1 1 Subnet Mask 255 255 255 0 Save LAN Settings DHCP Server Configuration The DHCP Server Configuration screen enables the router to automatically assign IP address to attached computers using the Dynamic Host Control Protocol DHCP Server Configuration Server Settings Enabled Disabled Client IF Address Range 192 168 1 100 131 Client Network Information Optional Domain Mame ONS Server 1 T Static Address Assignments mentine Sig Host Identifier Internal Address _ Hostname 192 168 1 ada Save DHCP Settings View DHCP Table Server Configuration select ENABLED to activate the DHCP server and have the BPG510 assign IP addresses for connected devices 8x8 Inc 2005 Page 15 of 27 BPG510 User Interface Guide Client IP Address Range Enter the range of IP addresses available to local devices The BPG510 can support 32 IP addresses and the address range must be consecutive numbers between 1 and 255 Client Network Information Domain Name Enter the domain name used by the local LAN if any DNS Server 1 amp 2 Enter the IP addresses of the primary 1 and secondary 2 DNS server
14. f the computer you wish to configure as a DMZ and click SAVE DMZ HOST CONFIGURATION Page 10 of 27 8x8 Inc 2005 BPG510 User Interface Guide Detailed Screen Reference WAN Menu WAN Status The WAN Status screen displays information about the connection between the BPG510 and the DSL or cable modem WAN Status Interface Status Enabled Yes Service Routed Protocol Ethernet Interface Status Up Network Settings Dynamic IFP Assignment YES via DHOP IP Address 192 168 15 100 MAC Address 00 11 f5 0c 7fh3 Subnet Mask 255 255 255 0 Default Gateway 192 168 15 1 DNS Serwers 192 168 15 1 Domain Mame Update Interface Status ENABLED YES indicates the WAN interface has been activated NO indicates the interface has not been activated PROTOCOL Displays the protocol the BPG510 uses to communicate with the modem INTERFACE UP indicates the interface is functioning DOWN indicates the interface is not STATUS functioning Network Settings DYNAMIC IP Shows whether the BPG510 is configured to receive an IP address ASSIGNMENT automatically from the modem or the service provider IP ADDRESS Displays the BPG510 s IP address MAC ADDRESS Displays the BPG510 s MAC hardware address SUBNET MASK Displays the BPG510 s subnet mask DEFAULT Displays the IP address of the Default Gateway used by your service provider GATEWAY DNS ADDRESS Displays the IP address of the Domain Name System DNS server used by your service pro
15. ny data that is not in a port forwarding range will be sent to the DMZ Follow the steps below to configure a computer as a DMZ CAUTION The BPG510 cannot protect a computer configured to operate as the DMZ from malicious access W Traffic sent to the DMZ is still subject to translation by NAT This means that applications that are damaged by NAT will still be affected 8x8 Inc 2005 Page 21 of 27 BPG510 User Interface Guide DMZ Host Configuration OMZ Host iP Address 192 166 1 iN Save DMZ Host Configuration SYSTEM Menu Set Security Password Set Security Password Mo password installed Mew password Confirmnew password New password Enter the password you wan to use for this account Confirm new password Enter the same password again for confirmation Localization The Localization screen controls the time and place settings Page 22 of 27 8x8 Inc 2005 BPG510 User Interface Guide Localization Country United States NTP Server Time Zone GMT 08 00 Pacific Time Adjust clack for daylight savings Save Localization Settings Country select the country the BPG510 is currently operating in NTP Server Enter the Network Time Protocol NTP server you want the BPG510 to use to automatically update the date and time settings If you don t enter an NTP server the time and date stamp on Caller ID messages may not work correctly Time Zone select the time zone wh
16. on DOTA version 1 0 UWS 8x8 001401 Downloader Code Version 1 0 US 8x8 010301 Copyright 2002 2005 8x6 Inc Page 4 of 27 8x8 Inc 2005 BPG510 User Interface Guide f you have any trouble opening the utility first check the connection between your computer and the BPG510 Then reboot your computer while it is connected to the BPG510 8x8 Inc 2005 Page 5 of 27 BPG510 User Interface Guide Connecting to Your Broadband Modem Setting up with DHCP The BPG510 is configured for use with Dynamic Host Configuration Protocol DHCP by default If your broadband connection uses DHCP then you simply have to connect your phone s WAN port to your broadband modem and then connect the power on the phone See the BPG510 Router configuration Guide for detailed connection diagrams lf you have disabled the DHCP client for example it you have used your phone in a network requiring either PPPoE or a static IP address and need to re enable it follow the steps below 1 Open the configuration utility 2 Inthe menu bar down the left side of the screen select WAN 3 Inthe top menu bar select WAN Settings This will open the Wan Configuration screen WAN Configuration laana al Device Operating Mode Route r Obtain WAN configuration dynamically O Specify static WAN configuration IF Address IF Metmask IF Gateway IP DNS Server 1 IP DNS Server 2 IP DNS Server 3 Host Mame Domain N
17. s of the port range you wan to map to this computer If you want to forward a single port only enter the same port number in both spaces NOTE Port ranges are consecutive If you need to assign non consecutive ports to a computer you must enter that computer twice with different port ranges PROTOCOL Select TCP UDP or BOTH TCP UDP according to the needs of your network DESTINATION Enter the IP address of the computer you want to use as the host ADDRESS computer for these services then click ADD Filtering Configuration The Filtering Configuration screen lets you block certain computers from accessing the Internet or from accessing certain services on the Internet You can filter computers by IP address or by MAC address Page 20 of 27 8x8 Inc 2005 BPG510 User Interface Guide Filtering Configuration Fittered LAN IP Addresses IF Address Protocol 192 168 1 Both Add Filtered LAN IP Addresses Enter the IP addresses you want to block from accessing the Internet connection select Both The computer at the IP address you specified will now be blocked from Internet DMZ Host Configuration lf you want to have one computer on your network receive all un forwarded data that arrives at your firewall for instance because you want to monitor network traffic on the WAN side or you have one computer running too many services to configure all the forwarded ports you can establish a single computer as a DMZ A
18. s used by the local LAN Static Address Assignments Complete this information to make the BPG510 assign the same IP address to a device every time Assign a static IP address if the device serves as a host for any Internet services You can assign up to eight static IP addresses To assign new static IP addresses click Add Once a static IP address is assigned you can remove it by clicking the Remove button beside it Identify Using select whether you want to identify the local device by a HOST NAME of by the MAC ADDRESS Host Identifier Enter the name or the MAC address of the host Internal Address Enter the IP address you want the DHCP server to assign to this device DHCP Client Table The DHCP Client Table screen displays the name and ID based on the MAC address of connected devices it also shows the IP address and how long each address is leased Page 16 of 27 8x8 Inc 2005 BPG510 User Interface Guide lt 4 DHCP Client Table Microsoft Internet Explorer DHCP Client Table Computer Name Client iD IP Address LT107 O1000DB80FDFIC4 1927 166 1 100 Clear client binding table Update Close 8x8 Inc 2005 Page 17 of 27 BPG510 User Interface Guide Router Configuration Router Configuration Dynamic Routing RX Mode Disabled TX Mode Disabled Static Routing Subnet Mask Gateway IP DestIP Address Metric Interface _ LAN Aca Save Router Settings View Routing Table
19. to the host server Internet protocol separates data traffic for different services into port ranges To configure the BPG510 to forward any data that comes in on the port range of the service follow the steps below 1 Determine the TCP UDP ports used by the application you are hosting A list of commonly used ports can be found at http Awww iana org assignments port numbers 2 Open the configuration utility 3 In the menu bar down the left side of the screen select LAWN 4 Inthe menu bar on the top of the screen select Port Forwarding This opens the Port Forwarding Configuration screen Page 8 of 27 8x8 Inc 2005 BPG510 User Interface Guide Port Forwarding Configuration Reserved Ports The following ports have been reserved by the CPE and may not be forwarded to the LAN 68 44655 2000 8019 Port Forwarding to LAN Part Range Protocol l Destination Address Both 192 168 1 Add 5 Under Port Range enter the first port of the range you want to forward in the first box and the last port of the range in the second box If the service you are supporting only uses one port enter the same port number in both boxes Ports in each range must be consecutive If your service uses non consecutive ports simply enter them as two separate port ranges 6 Under Protocol select whether the ports in the range are UDP ports TCP ports or BOTH 7 Under Destination Address enter the IP address of the computer you want th
20. vider DOMAIN NAME Displays the domain name of the WAN side service provider s network 8x8 Inc 2005 Page 11 of 27 BPG510 User Interface Guide WAN Configuration The WAN Configuration screen allows you to set the BPG510 to operate with your DSL cable modem WAN Configuration Device Operating Mode GENiz a Obtain WAN configuration dynamically Specify static WAN configuration IF Address IF Metrmask IF Gateway IF DNS Server 1 i IF DNS Serwer 2 IP DNS Server 3 Host Mame Domain Mame Save WAN Settings CAUTION Saving the WAN Configuration reboots the BPG510 Device Operating Mode This section allows you to select BPG510 as a switch or a router device If you connect BPG f you are connecting BPG510 as a client behind another router then you will select BPG510 as a SWITCH Obtain WAN configuration dynamically Select this option if you do not have a static IP address the BPG510 will automatically obtain its IP address and other information from your service provider Specify fixed WAN configuration lf your provider gave you a static IP address select this option and fill out all the information below IP ADDRESS Enter the IP address you received from your service provider in the following format XXX XXX XXX X SUBNET MASK Enter the subnet mask you received from your service provider in the following format XXX XXX XXX X DEFAULT Enter the default gateway address in the follo
21. wing format XXX XXX XXX X This Page 12 of 27 8x8 Inc 2005 BPG510 User Interface Guide GATEWAY is the IP address of your service provider s router DNS ADDRESS ___ Enter the IP address of the Domain Name System DNS server used by your service provider Use the following format XXX XXX XXX X PPPoE The WAN PPPoE screen configures the BPG510 to support point to point protocol over Ethernet WAN PPPoE Configuration Enable PPPoE Now Authentication Username Password Settings service Mame AC Mame Save PPPOE Settings CAUTION Saving the PPPoE Configuration reboots the BPG510 Enable PPPoE select YES to activate the PPPoE protocol Authentication Enter the USERNAME and PASSWORD you use to login to the PPPoE service Settings Enter the SERVICE NAME and AC NAME required by your ISP If you are not sure leave this blank 8x8 Inc 2005 Page 13 of 27 BPG510 User Interface Guide MAC Cloning The MAC address is a unique hardware address assigned to each Ethernet device If your provider requires you to have a single MAC address enter the MAC address that your provider expects The BPG510 will then transmit all packets as if they Originated from that MAC address MAC Cloning Configuration WAM MAC Address Clonedy Save MAC Cloning Settings LAN Menu LAN Configuration The LAN Configuration screen controls the IP address of the LAN port on the BPG510 If you have an another d
Download Pdf Manuals
Related Search