3M MPro110 User's Manual
Contents
1. 3M Micro Professional Projector MPro110 Image Size Increase or decrease the projector to wall distance 305 mm 12 in to 1800 mm 71 in to project an image ranging from 163 mm to 975 mm 6 4 in to 38 4 in wide Projector To Wall Distance Image Width 305 mm 12 in 163 mm 6 4 in 610 mm 24 in 235 mm 9 3 in 914 mm 36 in 355 mm 14 in 1219 mm 48 in 523 mm 20 6 in 1524 mm 60 in 739 mm 29 1 in 1800 mm 71 in 975 mm 38 4 in Focus Adjustment Rotate the focus wheel until the image is clear Cleaning Projector 1 Turn off the projector and disconnect power and other cables 2 Use soft cloth to wipe off dust If the dust is difficult to remove dampen the cloth with clean water and then wipe the projector clean Then use a clean cloth to dry the projector Important Notes e not use cleaning chemicals or solvents to clean the projector Cleaning chemicals and solvents may cause the plastic parts to discolor 12 2008 3M All Rights Reserved 3M Micro Professional Projector MPro110 Troubleshooting Problem Image is fuzzy Does not run on battery power Blank image LED flashing red LED is green LED is orange Video or VGA icon is flashing Video VGA icons alternate flashing 2008 3M All Rights Reserved Cause Projector to screen distance out side of limits Image not focused Battery not charged Battery needs replacement Power is off2. Projector in Power Saver Mode Battery is low Projector in Power Saver Mode 3 Battery is charging No input signal is detected by projector No input cable is detected Solution Place projector 200 1800 mm from wall Turn focus to sharpen image Plug in AC adapter and turn power switch Off to charge bat tery Replace battery if it will not hold a charge Turn projector ON Input source must be powered ON and sending an input signal Plug in AC adapter and turn power switch Off to charge battery Projected images returns when input signal resumes LED is orange during charging and goes off when battery is fully charged Turn on power for input source Connect input cable and power on input source 5 10 24990 N n g 3M Micro Professional Projector MPro110 Description Specification Specifications Projector Imager Technology Size Image Resolution Image Aspect Ratio Projection Distance Image Size Throw Ratio Width Distance Lens Offset Inputs Compatible Resolution Refresh Rates Video Compatibility Dimensions Weight Tripod Socket Operating Temperature Altitude LCOS 11 9 mm 0 47 640 x 480 Pixels 43 305 1800 mm 12 70 163 975 mm 6 4 38 4 0 53 1 1 none VGA Composite Video DC Power VGA SVGA XGA 60 Hz NTSC PAL NTSC M PAL 115 mm L x 50 mm W x 22 mm H 4 1
3. 2 x 1 31 32 x 7 8 160 g 5 6 oz 14 20 10 27 C 50 80 Sea Level to 1 829 m 6000 14 2008 3M All Rights Reserved 3M Micro Professional Projector MPro110 e Se 10 24990 NK03 S005 Rechargeable Lithium lon Battery Type Rechargeable Lithium ion Battery Rated Capacity 3 7 V 1050mAh Dimensions 40 4 x 34 4 x 9 4 mm 1 6 x 1 4 x 0 4 Do not throw battery into trash Please dispose of according to federal state or local laws Supported Computer Signals Description Resolution width x height Refresh Rate VGA 640 x 480 60 Hz SVGA 800 x 600 60 Hz XGA 1024 x 768 60 Hz WXGA 1280 x 768 60 Hz Replacement Parts Accessories US AC Power Adapter 78 6969 9972 7 EU AC Power Adapter 78 6969 9977 6 UK AC Power Adapter 78 6969 9995 8 Rechargeable Battery 78 6969 9974 3 e ee and RCA Adapter 8 6969 9979 2 VGA Cable 78 6969 9978 4 2008 3M All Rights Reserved 15 Guide N S p lt gt 3M Micro Professional Projector 110 Limited Warranty e The 3M Micro Professional Projector MPro110 the product is warranted to be free from defects in material or manufacture for a period of 90 days from the date of purchase e Allother accessories included with the product are warranted to be free from defects in material or manufacture for a period of 90 days from the date of purchase e Optional product accessories that are not sold as p
4. 3M Micro Professional Projector MPro110 Operator s Guide 8 8 3M Micro Professional Projector 110 o EE Contents Intended Use Statement 3 Trademarks and Copyrights 3 SALLY MOMMA OM eden 3 Safety LADEIS T 5 Package COMENTS 7 7 8 Operating mh t entes 10 13 14 Limited 16 2 2008 3M All Rights Reserved 3M Micro Professional Projector MPro110 Intended Use Statement The 3M Micro Professional Projector MPro110 is designed to operate with the 3M specified battery and 3M battery charger and in a normal office and home environment e 10 27 C 50 80 F 10 80 RH without condensation 0 1 829 0 6000 above sea level The ambient operating environment should be free of airborne smoke grease oil and other contaminants that can affect the operation or performance of the projector Use of this product in adverse conditions will void the product warranty Trademarks and Copyrights 3M is a trademark of 3M Company VGA and XGA ar
5. art of the product are subject to individual warranties THE WARRANTIES STATED ABOVE ARE EXCLUSIVE AND ARE MADE IN PLACE OF ANY AND ALL WARRANTIES EXPRESS OR IMPLIED WARRANTIES OR CONDITIONS INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY INDUSTRY PRACTICE OR CUSTOM OR TRADE USAGE In the event the 3M product fails to conform to the above stated warranties within the applicable warranty period your exclusive remedy shall be at 3M s option to replace or repair the 3M product or to refund the purchase price of the 3M product All replaced parts or products become property of 3M If the product is repaired 3M will repair the defective part s with a new or used part s If the 3M product is replaced 3M will replace the 3M product with the same or equivalent model and with a new or refurbished 3M product In the case of an approved warranty claim the replacement 3M product will carry only the remaining term of the original 3M product s warranty period as stated above For warranty service you must provide proof of the date of the original purchase else the manufacturing code date will be used to establish the start date of the warranty The following are exclusions to the above listed warranty a This warranty does not cover 3M product that is modified or damaged through improper storage misuse abuse accident vandalism improper installation neglect improper shipping damage caused b
6. e cables may have to be used with the core set to the projector side Use the cables which are included with the projector or specified Note Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment CE Statement ElectroMagnectic Compatibility Statement Meets 2004 108 EC Directive Low Voltage Directive Meets 2006 95 Directive WEEE Statement The following information is only for EU members States The mark shown to the right is in compliance with Waste Electrical and Electronic Equipment Directive 2002 96 EC WEEE The mark indicates the requirement NOT to dispose the equipment as unsorted municipal waste but use the return and collection systems according to local law RoHS Statement 3M Projection Systems can provide RoHS certification for products meeting the RoHS directive European EU Restriction of Hazardous Substances RoHS Directive 2002 95 EC RoHS compliant means that the product or part does not contain any of the substances in excess of the following maximum concentration values in any homogeneous material unless the substance is in an application that is exempt under RoHS as amended 0 1 by weight for lead mercury hexavalent chromium polybrominated biphenyls or polybrominated diphenyl ethers or b 0 01 by weight for cadmium This information represents 3M s knowledge and belief which may be based on in
7. e or a 3M Authorized Service Provider to obtain an RMA Return Material Authorization number before returning the product If you are inside the Continental United States of America please contact Customer Service at 1 866 631 1656 or email meetings mmm com What 3M Will Do To Correct Problems e f your 3M product requires service will ask you to bring or send the product securely packaged in its original container or equivalent along with proof of the date of original purchase to your 3M Service Dealer or 3M Service Center e 3M will at its option repair or replace the defective unit without charge for parts or labor Return of the 3M product will be at 3M s expense e When warranty service involves the exchange of the product or of a part the item replaced becomes 3M property e exchanged 3M product or part may be new or previously refurbished to the 3M standard of quality and at 3M s option the replacement may be another model of like kind and quality e liability for replacement of the warranted product or part will not exceed the original retail selling price of the 3M product Exchange or replacement products or parts assume the remaining warranty period of the product covered by this limited warranty However each replacement lamp carries the limited 90 day warranty stated above 18 2008 3M All Rights Reserved Projection Systems 3M Austin Center 6801 River Place B
8. e trademarks of International Business Machines Corporation S VGA is a registered trademark of the Video Electronics Standards Association No publication or commercial use may be made of this material without the express written permission of 3M Safety Information Please read understand and follow all safety information contained in these instructions prior to the use of this projector Retain these instructions for future reference Explanation of Signal Word Consequences A Warning Indicates a potentially hazardous situation which if not avoided could result in death or serious injury and or property damage Caution Indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury and or property damage 2008 3M All Rights Reserved 3 e 10 24990 n n g 3M Micro Professional Projector MPro110 Warning To reduce the risk associated with hazardous voltage e modify this product in any way Use only approved replacement components Do not attempt to service this projector other than battery replacement There are no user serviceable parts other than the battery Service to be performed only by a 3M authorized service provider using 3M approved system components e Do not use the wall power supply in a wet environment e Donotuse with a damaged wall power supply Replace damaged part prior to use T
9. e with the instruction manual may cause interference to radio communications It has been tested and found to comply with the limits for a Class B computing device pursuant to Subpart B of Part 15 of the FCC Rules which are designed to provide reasonable protection against such interference when operated in a residential installation However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help NOTICE This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Cet appareil num rique de la classe B respecte toutes les exigences du R glement sur le mat riel brouilleur du Canada 2008 3M All Rights Reserved 5 n Te 2 m a 3M Micro Professional Projector MPro110 INSTRUCTIONS TO USERS This equipment complies with the requirements of FCC equipment provided that the following conditions are met Th
10. formation provided by third party suppliers to 3M 6 2008 3M All Rights Reserved 3M Micro Professional Projector MPro110 Package Contents 1 Projector 2 Battery Charger AC Adapter 3 Video Cable 4 VGA Cable 5 Battery 6 Adapter Note In some regions the battery charger AC adapter will come with an outlet adapter Parts 1 Focus Wheel Lens Power On Off Video IN VGA IN Power and Charge LEDs DC Power IN DO N 2008 3M All Rights Reserved 5 25 os pate e Guide n Te 2 3M Micro Professional Projector 110 Getting Started Install Battery The 3M 110 comes with a rechargeable Lithium lon Li lon battery The battery should be charged before using the projector with the battery Important Note Switch projector OFF and disconnect all cables before installing the battery Use only the 3M specified battery 78 6969 9974 3 To install the battery remove screw slide the back cover off insert the battery and reinstall the cover Caution To reduce the risk associated with explosion e Only replace the battery with the approved battery To reduce the risk of environmental contamination e Dispose of used battery according to applicable local state and federal regulations 8 2008 3M All Rights Reserved 3M Micro Professional Projector 110 Charge the Battery The 3M 110 comes wi
11. ghts Reserved 3M Micro Professional Projector 110 Connecting to a Computer Video Source There are several types of computers that output a video signal desktop computers laptop computers ultra portable computers and some personal digital assistants PDAs The 3M MPro110 can project the video from these devices using its VGA port 1 Connect the included VGA Cable to the projector 2 Connect the VGA Cable to the device s video output Powering On Slide the power switch to the ON position The power LED will turn green and the projector will energize The projector will automatically detect the connected cable and switch to the appropriate port Then the projector will detect and display the video source If the video source is not detected the projector will display a blue image and the name of the selected port CVBS video or VGA NOTE The projector will switch to power save mode in 30 seconds if no video or computer source is detected The projector will switch to sleep mode in 60 seconds if there is no source When a source is detected the projector returns to full operating mode Tip The video output on some devices is turned off by default Please refer to the device s documentation for details on enabling the video Powering Off Slide the power switch to the OFF position Disconnect video VGA and AC adapter cables 2008 3M All Rights Reserved 11 e 10 24990 N n g
12. hould the 3M label or logo or the rating label or serial number be removed unless otherwise stated in writing for the purposed of private labeling for partnership requirements i This warranty does not cover postage insurance or shipping costs incurred in presenting your 3M product for warranty service Said costs are the customer s responsibility If a claimed defect cannot be identified or reproduced in service the customer may be held responsible for cost incurred Should your warranty upgrade include a change out service and the claimed defect cannot be identified or reproduced by the technician the customer will be responsible for call out costs FAILURE TO FOLLOW THE INSTRUCTIONS CONTAINED IN THE APPROPRIATE 3M product MANUAL OR TO USE THE 3M PRODUCT IN ACCORDANCE WITH 3M S INTENDED USE STATEMENT WILL VOID ALL WARRANTIES AND LIMITED REMEDIES 2008 3M All Rights Reserved 17 3M Micro Professional Projector MPro110 Guide n Te 2 EXCEPT AS SPECIFICALLY STATED IN THE APPLICABLE 3M PRODUCT MANUAL 3M SHALL NOT BE LIABLE FOR ANY INDIRECT INCIDENTAL SPECIAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO LOSS OF PROFITS REVENUE OR BUSINESS RESULTING FROM OR IN ANY WAY RELATED TO PERFORMANCE USE OR INABILITY TO USE ANY OF THE 3M PRODUCT This limitation applies regardless of the legal theory upon which damages are sought For warranty support please call or write your local 3M offic
13. lvd Austin TX 78726 9000 866 631 1656 www 3M com meetings e mail meetings mmm com 3M is a trademark of 3M Company Please recycle Printed in Taiwan 3M 2008 All rights reserved August 2008 78 6971 1437 5 C
14. o reduce the risk associated with fire and explosion Do not immerse the projector or battery in any liquid or allow either to get wet Use only wall power supply and Li lon battery provided Do not disassemble short or expose the battery to high temperature Do not overcharge or rapidly discharge the battery Do not dispose of the battery by incineration or fire Do not operate this projector in any environment above 100 F 38 C Do not expose the projector or battery to direct sunlight in a closed space such as a vehicle To reduce the risks associated with driver distraction in a moving motor vehicle e Donot use this projector in a moving motor vehicle Caution To reduce the risk associated with environmental contamination e Dispose of all system components in accordance with applicable government regulations To reduce the risks associated with LED visible bright light e Do not stare directly into the LED light beam To reduce the risks associated with tripping and falling Position the charging cord and data cables so that they can not be tripped over SAVE THESE INSTRUCTIONS 4 2008 3M All Rights Reserved 3M Micro Professional Projector MPro110 Safety Labels e 5 10 24990 Model NK 5 2 ating CLASS 1 LED PRODUCT FCC STATEMENT CLASS B This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordanc
15. th a battery charger AC adapter Use the battery charger AC adapter to power the projector when the battery is not charged or installed and to charge the battery When the battery needs charging the image will turn black and the Power LED will flash red To charge the battery 1 Turn the power switch OFF 2 Connect the battery charger AC adapter to the projector s DC in 3 Plug the battery charger AC adapter into an electrical outlet 4 The charge LED lights orange while the battery is charging The battery will be fully charged in about 2 hours 5 Once charging is complete the charge LED will turn off Note The battery will not charge when the power switch is in the ON position Turn the power switch OFF to charge battery 2008 3M All Rights Reserved 9 e 10 24990 Guide n Te 2 um 3M Micro Professional Projector 110 Operating Instructions Connecting to a Video Source There are many devices that output video signals digital cameras video phones and portable video players The 3M MPro110 can project the video from these devices using its video port 1 Connect the included video cable to the projector 2 Connect the video cable to the video source s cable or the video output port NOTE If the two cables have the same connector on the end use the RCA adapter to connect the two cables 3 CSD m 10 2008 3M All Ri
16. y acts of war disasters such as fire flood and lightning improper electrical current software problems interaction with non 3M products or service other than by an 3M Authorized Service Provider neglect or mishandling by any person Normal wear and tear is not covered under warranty 16 2008 3M All Rights Reserved 3M Micro Professional Projector MPro110 e 5 10 24990 b 3M product is designed to operate in the typical indoor environment This warranty does not cover 3M product used outside of the following circumstances e 100 240 AC 50 60 Hz e 10 270 50 80 F 10 80 RH without condensation e 0 1828 0 6000 feet above sea level The air intake and exhaust vent must be clear of obstructions Inadequate air ventilation will cause the 3M product to malfunction or will cause damage to the 3M product which will void the warranty d This warranty does not cover any additional costs including but not limited to those associated with removal cleaning or installation of the 3M product adjustments mechanical or electronic made to the 3M product e This warranty covers only normal use of the product 24 hour per day or other excessive continual use causes strain and is not considered normal use This warranty does not cover consumables 0 fuses other than lamps and only as set forth below 9 This warranty is not transferable 3M is not responsible for warranty service s
Download Pdf Manuals
Related Search