Transcend TS8GEMC210 flash memory
Contents
1. All rights reserved Transcend and the Transcend logo are registered trademarks of Transcend Information Inc Product offerings and specifications are subject to change without notice All other products brand names company names and logos are trademarks of their respective owners2. Transcend and the Transcend logo are registered trademarks of Transcend Information Inc Product offerings and specifications are subject to ch ange without notice All other products brand names company names and logos are trademarks of their respective owners T Transcend good memories start here www transcend info com Extended CSD register R Read only W One time programmable and not readable R W One time programmable and readable W E Multiple writable with value kept after power failure H W reset assertion and any CMDO reset and not readable R W E Multiple writable with value kept after power failure H W reset assertion and any CMDO reset and readable R W C_P Writable after value cleared by power failure and H W reset assertion the value not cleared by CMDO reset and readable R W E_P Multiple writable with value reset after power failure H W reset assertion and any CMDO reset and readable W E_P Multiple writable with value reset after power failure H W reset assertion and any CMDO reset and not readable Name Field Cell Value CSD slice Type Byte Supported Command S_CMD_SET R th 504 Sets HPI features HPl_FEATURES R 3h 503 Background operations BKOPS_SUPPORT R th 502 support Max packed read MAX_PACKED_READS R 8h 501 commands Max packed write MAX_PACKED_WRITES R 8h 500 commands Data tag support DATA_TAG_SUPPORT R th 499 Tag
3. 51 spec Enhanced reliable write is a special write mode in which the old data pointed to by a logical address must remain unchanged until the new data written to same logical address has been successfully programmed This is to ensure that the target address updated by the reliable write transaction never contains undefined data When writing in reliable write mode data will remain valid even if a sudden power loss occurs during programming Sanitize The sanitize operation is a feature in addition to Trim and Erase is used to remove data from EMC210 The use of sanitize operation requires EMC210 to physically remove data from the All rights reserved Transcend and the Transcend logo are registered trademarks of Transcend Information Inc Product offerings and specifications are subject to change without notice All other products brand names company names and logos are trademarks of their respective owners T Transcend good memories start here www transcend info com unmapped user address space For more details refer to section 6 6 13 of the JEDEC Standard Specification NO JESD84 B451 e Discard The discard is similar operation to Trim The discard function allows the host to identify data that s no longer required so that EMC210 can erase the data if necessary during background erase events For more details refer to section 6 6 14 of the JEDEC Standard Specification NO JESD84 B451 e Erase In addition to the implicit eras
4. JESD84 B451 e DDR I F Support DDR signaling to double bus performance For more details refer to JESD84 B451 standard e Replay Protected Memory Block A signed access to a Replay Protected Memory Block is provided This function provides means for the system to store data to the specific memory area in an authenticated and replay protected manner For more details refer to section 6 6 22 of the JEDEC standard Specification NO JESD84 B451 e Background Operation EMC210 has various maintenance operations need to perform internally In order to reduce latencies during time critical operation like read and write it is better to execute maintenance operation in other times when the host is not being serviced For more details refer to section 6 6 25 of the JEDEC Standard Specification NO JESD84 B451 All rights reserved Transcend and the Transcend logo are registered trademarks of Transcend Information Inc Product offerings and specifications are subject to change without notice All other products brand names company names and logos are trademarks of their respective owners T Transcend good memories start here www transcend info com Product Specifications e Specification P N Package Ball Number Technology TS8GEMC210 11 5 x 13x 1 0 mm 153 MLC TS16GEMC210 11 5x13x1 0 mm 153 MLC TS32GEMC210 11 5x13x 1 2mm 153 MLC e Performance Performance P N Seq Read Seq Wr
5. Mechanical Property Shock 500G ims JESD22B 104 Vibration 20 0G 20 2000Hz JESD22B103 All rights reserved Transcend and the Transcend logo are registered trademarks of Transcend Information Inc Product offerings and specifications are subject to cha ange without notice All other products brand names company names and logos are trademarks of their respective owners T Transcend good memories start here www transcend info com Physical Specifications PIN 1 CORNER E 123456769 101234 D1 OOMMNOITE ZAC EZV sywBo DMENSION IN MM DIMENSION IN INCH _ M Nom max MIN Nom MAX o 12 90 13 00 13 10 0 508 0 512 0516 e inso riso 1180 0 448 oss 0487 e osBsc 0o20 Bsc JEDEC All rights reserved Transcend and the Transcend logo are registered trademarks of Transcend Information Inc Product offerings and specifications are subject to change without notice All other products brand names company names and logos are trademarks of their respective owners T Transcend good memories start here www transcend info com Interface Description Top View Ball Down red Transcend and the Transcend logo are d trademarks of Transcend Information Inc Product offerings and specifications are subject to change without notice All other products brand names company names and logos are trademarks of their respective ow T Transcend good
6. memories start here www transcend info com 153 Ball AA Device Symbol Type Ball Function M6 CLK Input Clock Each cycle directs a 1 bit transfer on the command and DAT lines M5 CMD Input Command A bidirectional channel used for device initialization and command transfers Command has two operation modes e Open drain for initialization e Push pull for fast command transfer A3 DATO O Data 1 00 Bidirectional channel used for data transfer A4 DAT1 O Data 1 01 Bidirectional channel used for data transfer A5 DAT2 I O Data 1 02 Bidirectional channel used for data transfer B2 DAT3 I O Data 1 03 Bidirectional channel used for data transfer B3 DAT4 I O Data 1 04 Bidirectional channel used for data transfer B4 DAT5 O Data 1 05 Bidirectional channel used for data transfer B5 DAT6 O Data 1 06 Bidirectional channel used for data transfer B6 DAT7 O Data 1 O7 Bidirectional channel used for data transfer K5 RST_n Input Reset signal pin E6 F5 J10 K9 VCC Supply VCC Flash memory I F and Flash memory power supply C6 M4 N4 P3 P5 VCCQ Supply VCCQ Memory controller core and MMC interface I O power supply All rights reserved Transcend and the Transcend logo are registered trademarks of Transcend Information Inc Product offerings and specifications are subject to change without notice All other products brand names company names and log
7. unit size TAG_UNIT_SIZE R Oh 498 Tag Resource size TAG_RES_SIZE R 6h 497 Context management CONTEXT_CAPABILITIES R 78h 496 capabilities Large Unit Size LARGE_UNIT_SIZE_M1 R th 495 All rights reserved Transcend and the Transcend logo are registered trademarks of Transcend Information Inc Product offerings and specifications are subject to ch ange without notice All other products brand names company names and logos are trademarks of their respective owners D Transcend good memories start here www transcend info com Extended partitions EXT_SUPPORT R 3h 494 attribute support Cache size CACHE_SIZE R 20000h 252 249 Generic CMD6 timeout GENERIC_CMD6_TIME R 64h 248 Power off POWER_OFF_LONG_TIME R 64h 247 notification long timeout Background operations BKOPS_STATUS R Oh 246 status Number of correctly CORRECTLY_PRG_SECTOR R Oh 245 242 programmed sectors S_NUM 1 initialization time after INI_TIMEOUT_AP R Ah 241 partitioning Power class for 52MHz PWR_CL_DDR_52_360 R Oh 239 DDR at 3 6V Power class for 52MHz PWR_CL_DDR_52_195 R Oh 238 DDR at 1 95V Power class for 200MHz PWR_CL_200 195 R Oh 237 at 1 95V Power class for 200MHz PWR_CL_200 130 R Oh 236 at 1 3V Minimum Write MIN_PERF_DDR_W_8 52 R Oh 235 Performance for 8bit at 52MHz in DDR mode Minimum Read MIN_PERF_DDR_R_8 52 R Oh 234 Performanc
8. RT R 7h 160 Max Enhanced Area Size MAX_ENH_SIZE_ MULT R Depends on 159 157 capacity Partitions attribute PARTITIONS_ ATTRIBUTE R W Oh 156 Partitioning Setting PARTITION SETTING_COMP R W Oh 155 LETED General Purpose Partition GP_SIZE_MULT R W Oh 154 143 Size Enhanced User Data ENH_SIZE_ MULT R W Oh 142 140 Area Size Enhanced User Data ENH_START_ADDR R W Oh 139 136 Start Address Bad Block Management SEC_BAD_BLK_MGMNT R W Oh 134 mode Package Case TCASE_SUPPORT W E_P Oh 132 Temperature is controlled Periodic Wake up PERIODIC_WAKEUP R W E Oh 131 All rights reserved Transcend and the Transcend logo are registered trademarks of Transcend Information Inc Product offerings and specifications are subject to ch ange without notice All other products brand names company names and logos are trademarks of their respective owners T Transcend good memories start here www transcend info com Program CID CSD in PROGRAM_CID_CSD_DDR R Oh 130 DDR mode support SUPPORT Vendor Specific Fields VENDOR_SPECIFIC_FIELD vendor Reserved 127 64 specific UDA Quick Health info UDA_HEALTH_STATUS R Oh 71 68 EUDA Quick Health info EUDA_HEALTH_STATUS R Oh 67 64 Native sector size NATIVE_SECTOR_SIZE R th 63 Sector size emulation USE_NATIVE_SECTOR R W Oh 62 Sector size DATA_SECTOR_SIZE R Oh 61 1st initialization after INI_LTIMEOU
9. T Transcend good memories start here www transcend info com EMC210 8GB 32GB e MMC 4 51 BGA 153 Transcend s e MMC EMC210 is an Embedded Flash Drive EFD designed for industrial applications such as embedded system vehicle entertainment system GPS games email office etc It is a hybrid device combining an embedded thin flash controller and standard MLC NAND flash memory supporting an industry standard e MMC 4 51 interface The outstanding performance and strict environment test enable Transcend s e MMC 210 to fulfill the needs of a wide variety of industrial application devices EMC 210 also provide 8 32GB of capacities in JEDEC compatible form factor and is an ideal solution for the vendors who require easy integration fast entry to market and high storage capacity Features e Compliant with JEDEC e MMC Specification Ver 4 51 e Supports three data bus widths 1bit default Abit 8bit e Uses an embedded thin memory controller and MLC NAND flash e Mechanical design complies with JESD84 C44 Specification e Dual power system e Core voltage VCC 2 7 3 6V e 1 0 VCCQ voltage either 1 7 1 95V or 2 7 3 6V e Variable clock frequencies of 0 200 MHz e Supports three data bus widths 1bit default Abit 8bit e Static global wear leveling e BCH ECC 53bit 1KB e Fully cycle environment test e RoHS compliant Transcend e MMC MMC Bus Interface Contro
10. T_EMU R Ah 60 disabling sector size emulation Class 6 commands CLASS_6_CTRL R W E_P Oh 59 control Number of addressed DYNCAP_NEEDED R Oh 58 group to be Released Exception events control EXCEPTION EVENTS CTRL R W E_P Oh 57 56 Exception events status EXCEPTION EVENTS STAT R Oh 55 54 US Extended Partitions EXT_PARTITIONS ATTRIBU R W Oh 53 52 Attribute TE Context configuration CONTEXT_CONF R W E_P Oh 51 37 Packed command status PACKED _COMMAND_STATU R Oh 36 S Packed command failure PACKED_FAILURE_INDEX R Oh 35 index Power Off Notification POWER_OFF_NOTIFICATIO R W E_P Oh 34 N Control to turn the Cache CACHE_CTRL R W E_P Oh 33 ON OFF Flushing of the cache FLUSH_CACHE W E_P Oh 32 All rights reserved Transcend and the Transcend logo are registered trademarks of Transcend Information Inc Product offerings and specifications are subject to change wi ithout notice All other products brand names company names and logos are trademarks of their respective owners Uy Transcend good memories start here www transcend info com Marking 1 row Transcend LOGO 2 row Sales P N d row Internal use 4 row Country of Origin Date Code 5 row Serial number Transcend TS32GEMC210 9221BA 326 01051 TW 1504 123456 0000 Revision History Version Date Modification Content V0 1 2015 03 23 V0 2 2015 03 31 V1 0 2015 04 08 Formal Release
11. e executed by EMC210 as part of the write operation provides a host explicit erase function For more details refer to section 6 6 11 of the JEDEC Standard Specification NO JESD84 B451 e Trim The Trim operation is similar to the default erase operation described above The Trim function applies the erase operation to write blocks instead of erase groups The Trim function allows the host to identify data that s no longer required so that EMC210 can erase the data if necessary during background erase events For more details refer to section 6 6 12 of the JEDEC Standard Specification NO JESD84 B451 e Partition management EMC210 offers the possibility for the host to configure addition split local memory partitions with independent addressable space starting from logical address 0x00000000 for different usage models Therefore memory block area scan be classified as follows v Two Boot Area partitions whose size is 4MB and from which booting from EMC210 can be performed v One RPMB partition accessed through a trusted mechanism whose size is defined as multiple of 128KB v Four General Purpose Area Partition to store sensitive data or for other host usage models The size of these partitions is a multiple of the write protect group Size can be programmed once in device life cycle one time programmable e Quick Health Info Transcend designs several byte in extended CSD of EMC210 Customers can read UDA and EUDA program erase cycles i
12. e for 8bit at 52MHz in DDR mode TRIM Multiplier TRIM _MULT R th 232 Secure Feature support SEC_FEATURE_SUPPORT R 55h 231 Secure Erase Multiplier SEC_ERASE_MULT R Ah 230 Secure TRIM Multiplier SEC_TRIM_MULT R Ah 229 Boot information BOOT_INFO R 7h 228 Boot partition size BOOT_SIZE_ MULTI R 20h 226 All rights reserved Transcend and the Transcend log jo are registered trademarks of Transcend Information Inc Product offerings and specifications are subject to chi ange without notice All other products brand names company nai mes and logos are trademarks of their respective owners TD Transcend good memories start here www transcend info com Access size ACC_SIZE R 6h 225 High capacity erase unit HC_ERASE_GRP_SIZE R th 224 size High capacity erase ERASE_TMEOUT_MULT R 2h 223 timeout Reliable write sector REL WR_SEC C R th 222 count High capacity write HC_WP_GRP_SIZE R 10h 221 protect group size Sleep current VCC S_C_VCC R 7h 220 Sleep current VCCQ S_C_VCCQ R 7h 219 Sleep awake timeout S_A_TIMEOUT R 13h 217 Sector Count SEC_COUNT R Depends on 215 212 capacity Minimum Write MIN _PERF_W_8 52 R 8h 210 Performance for 8bit at 52MHz Minimum Read MIN _PERF_R_8 52 R 8h 209 Performance for 8bit at 52MHz Minimum Write MIN_PERF_W_8 26 4 52 R 8h 208 Performance for 8bit at 26M z for 4bi
13. etter prepare itself for being powered off For more details refer to section 6 6 36 of the JEDEC Standard Specification NO JESD84 B451 e Packed Commands Read and write commands can be packed in groups of commands either all read or all write that transfer the data for all commands in the group in one transfer on the bus to reduce overheads For more details refer to section 6 6 29 of the JEDEC Standard Specification NO JESD84 B451 e Boot Partition EMC210 supports e MMC 4 51 boot operation modes Boot partition size is reflected in BOOT_SIZE_ MULT register value in extended CSD e Automatic Sleep Mode If there is no further command issued by the host in 11mS duration after the previously issued command is completed the device enters Power Saving Mode to reduce power consumption The host does not have to take any action for this to occur However if host want to achieve the lowest sleep current the host needs to shut down its clock to the memory device When the host is ready to access a memory device in sleep mode any command issued to it will cause devices to exit sleep mode Sleep CMD5 EMC210 may be switched between a sleep state and a standby state by SLEEP AWAKE CMD5 In the sleep state the power consumption of EMC210 is minimized For more details refer to section 6 6 21 of the JEDEC Standard Specification No JESD84 451 Enhanced Reliable Write EMC210 supports enhanced reliable write as defined in e MMC 4
14. ghts reserved Transcend and the Transcend log T Transcend good memories start here www transcend info com Parameter Min Max Unit Remark Supply voltage 3 3V 2 7 3 6 V Supply voltage 1 8V 1 7 1 95 V I O Leakage current 10 10 uA Open Drain bus signal level Output high voltage Von VCCQ 0 2 V lt Output Low voltage VoL 0 3 loL 2mA Push Pull bus signal level 2 7 3 6V Output high voltage Von 0 75 VCCQ V loH 100UA VDD min Output Low voltage VoL 0 125 VCCQ V lo 100uA VDD min Input high voltage Vix 0 625 VCCQ VCCQ 0 3 V Input Low voltage VIL GND 0 3 0 25 VCCQ V Push pull bus signal level 1 70V 1 95V Output high voltage Von VCCQ 0 45 V loH 2 mA Output Low voltage VoL 0 45 V lo 2 mA Input high voltage Vix 0 65 VCCQ VCCQ 0 3 V Input Low voltage VIL GND 0 3 0 35 VDD V All rights reserved Transcend and the Transcend logo are registered trademarks of Transcend Information Inc Product offerings and specifications are subject to change without notice All other products brand names company names and logos are trademarks of their respective owners TP Transcend good memories start here www transcend info com e MMC 4 51 selected feature overview e Power Off Notification The host should notify the device before it powers the device off This allows the device to b
15. h mode BUS_WIDTH W E_P 2h 183 Erased memory content ERASED _MEM_CONT R Oh 181 Partition configuration PARTITION CONFIG R W E amp Oh 179 R W E_P Boot config protection BOOT_CONFIG_PROT RW amp Oh 178 R W C_P Boot bus condition BOOT_BUS_CONDITION R W E Oh 177 High density erase group ERASE_GROUP_DEF R W E_P Oh 175 definition Boot area write protection BOOT_WP RW amp Oh 173 register R W C_P User area write protection USER_WP R W Oh 171 register R W C_P All rights reserved Transcend and the Transcend logo are registered trademarks of Transcend Information Inc Product offerings and specifications are subject to cl hange without notice All other products brand names company names and logos are trademarks of their respective owners T Transcend good memories start here www transcend info com amp R W E_P FW configuration FW_CONFIG R W Oh 169 RPMB Size RPMB_SIZE_ MULT R 20h 168 Write reliability setting WR_REL_SET R W 1Fh 167 register Write reliability parameter WR_REL_PARAM R 5h 166 register Start Sanitize operation SANITIZE_START W E_P Oh 165 Manually start BKOPS_START W E_P Oh 164 background operations Enable background BKOPS_EN R W Oh 163 operations handshake H W reset function RST_n_ FUNCTION R W Oh 162 HPI management HPI_MGMT R W E_P Oh 161 Partitioning Support PARTITIONING_SUPPO
16. ite Ran Read Ran Write TS8GEMC210 140 40 2100 IOPS 600 IOPS TS16GEMC210 140 60 2100 IOPS 700 IOPS TS32GEMC210 140 60 2100 IOPS 700 IOPS Depending on operating condition the result might be different e Terabytes Written P N Terabytes Written TS8GEMC210 9 23 TBW TS16GEMC210 18 46 TBW TS32GEMC210 36 92 TBW Depending on different programming behavior and type All rights reserved Transcend and the Transcend logo are registered trademarks of Transcend Information Inc Product offerings and specifications are subject to change without notice All other products brand names company names and logos are trademarks of their respective owners TP Transcend good memories start here www transcend info com e Power Consumption Power Consumption mA 25 C P N VCCQ APS Sleep Write Read TS8GEMC210 0 05 0 05 21 37 TS16GEMC210 0 05 0 05 23 37 TS32GEMC210 0 05 0 05 23 37 APS Auto Power Suspend e Power Supply P N VCC VCCQ TS8GEMC210 2 7 3 6V 1 7 1 95V 2 7 3 6V TS16GEMC210 2 7 3 6V 1 7 1 95V 2 7 3 6V TS32GEMC210 2 7 3 6V 1 7 1 95V 2 7 3 6V VCCQ I O 3 3V is not supported in HS200 operation e Temperature Operation Storage Temperature 25 C to 85 C 40 C to 85 C e Moisture Sensitivity The moisture sensitivity for EMC210 is MSL 3 e Mechanical Property
17. ller Data I O Flash All rights reserved Transcend and the Transcend logo are registered trademarks of Transcend Information Inc Product offerings and specifications are subject to change without notice All other products brand names company names and logos are trademarks of their respective owners T Transcend good memories start here www transcend info com e MMC Bus and Power Lines Transcend s e MMC bus has the following communication and power lines e CMD Command is a bidirectional signal The host and Transcend s e MMC operate in two modes open drain and push pull e DATO 7 Data lines are bidirectional signals Host and Transcend s e MMC operate in push pull mode e CLK Clock input e RST_n Hardware Reset Input e VCCQ VCCQ is the power supply line for host interface e VCC VCC is the power supply line for internal flash memory e VDDi VDDi is e MMC s internal power node not the power supply Connect 0 1uF capacitor from VDDi to ground e VSS VSSQ Ground lines Bus Signal Level v vccio Output high Input high level level VOH VIH Undefined Input low level Output low level GNDIO t ive owners jo are registered trademarks of Transcend Information Inc Product offerings and specifications are subject to change without notice All other products brand names company names and logos are trademarks of their respecti All ri
18. nc Product offerings and specifications are subject to chi T Transcend good memories start here www transcend info com R W C_P Writable after value cleared by power failure and H W reset assertion the value not cleared by CMDO0 reset and readable R W E_P Multiple writable with value reset after power failure H W reset assertion and any CMDO reset and readable W E_P Multiple writable with value reset after power failure H W reset assertion and any CMDO reset and not readable Name Field Width Cell Value CSD slice Type CSD structure CSD_STRUCTURE 2 R 11b 127 126 System specification SPEC_VERS 4 R 0100b 125 122 version Data read access time 1 TAAC 8 R 27h 119 112 Data read access time 2 NSAC 8 R Oth 111 104 in CLK cycles NSAC 100 Max bus clock frequency TRAN SPEED 8 R 32h 103 96 Card command classes CCC 12 R OF5h 95 84 Max read data block READ_BL_LEN 4 R 9h 83 80 length Partial blocks for read READ_BL_PARTIAL 1 R Ob 79 79 allowed Write block misalignment WRITE_BLK_MISALIG 1 R Ob 78 78 N Read block misalignment READ _BLK_MISALIGN 1 R Ob 77 77 DSR implemented DSR_IMP 1 R Ob 76 76 Device size C_SIZE 12 R FFFh 73 62 Max read current Voo VDD_R_CURR_MIN 3 R 111b 61 59 min Max read current Voo VDD_R_CURR_MAX 3 R 111b 58 56 All rights reserved Transcend and the Transcend logo are registered trademarks
19. nformation by CMD_8 and reading extended CSD structure without any performance suffer It s well designed for industrial use e Write Protect Management In order to allow the host to protect data against erase or write EMC210 supports two levels of write protect commands For more details refer to section 6 6 17 of the JEDEC Standard Specification NO JESD84 B451 All rights reserved Transcend and the Transcend logo are registered trademarks of Transcend Information Inc Product offerings and specifications are subject to change without notice All other products brand names company names and logos are trademarks of their respective owners T Transcend good memories start here www transcend info com e High Priority Interrupt HPI In some scenarios different types of data on the device may have different priorities for the host For example writing operation may be time consuming and therefore there might be a need to suppress the writing to allow demand paging requests in order launch a process when requested by the user For more details refer to section 6 6 26 of the JEDEC Standard Specification NO JESD84 B451 e H W Reset Hardware reset may be used by the host to reset the device moving the device to a Pre idle state and disabling the power on period write protect on blocks that was set as power on write protect before the reset was asserted For more details refer to section 6 15 9 of the JEDEC Standard Specification NO
20. of Transcend Information Inc Product offerings and specifications are subject to change without notice All other products brand names company names and logos are trademarks of their respective owners Uy Transcend good memories start here www transcend info com max Max write current Voo VDD _W_CURR_MIN 3 R 111b 55 53 min Max write current Voo VDD_W_CURR_MAX 3 R 111b 52 50 max Device size multiplier C_SIZE_MULT 3 R 111b 49 47 Erase group size ERASE_GRP_SIZE 5 R 11111b 46 42 Erase group size multiplier ERASE_GRP_MULT 5 R 11111b 41 37 Write protect group size WP_GRP_SIZE 5 R 01111b 36 32 Write protect group enable WP_GRP_ENABLE 1 R 1b 31 31 Manufacturer default ECC DEFAULT ECC 2 R 00b 30 29 Write speed factor R2W_FACTOR 3 R 010b 28 26 Max write data block WRITE_BL_LEN 4 R 9h 25 22 length Partial blocks for write WRITE_BL_PARTIAL 1 R Ob 21 21 allowed Content protection CONTENT _PROT_APP 1 R Ob 16 16 application File format group FILE FORMAT _GRP 1 R W Ob 15 15 Copy flag OTP COPY 1 R W 1b 14 14 Permanent write PERM_WRITE_PROTE 1 R W Ob 13 13 protection CT Temporary write TMP_WRITE_PROTEC 1 R W E_ Ob 12 12 protection T File format FILE FORMAT 2 R W 00b 11 10 ECC code ECC 2 R W E 00b 9 8 CRC CRC 7 R W E 1101001b 7 1 Not used always 1 1 1b 0 0 All rights reserved
21. os are trademarks of their respective owners T Transcend good memories start here www transcend info com 153 Ball AA Device Symbol Type Ball Function E7 G5 H10 K8 VSS Supply VSS Flash memory I F and Flash memory ground connection C4 N2 N5 P4 P6 VSSQ Supply VSSQ Memory controller core and MMC I F ground connection C2 VDDi VDDi Connect 0 1uF capacitor from VDDi to ground Miscellaneous D4 NC Index Index Can be connected to ground or left floating A1 A2 A8 A9 A10 A11 NC No connect A12 A13 A14 B1 B7 Can be connected to ground or left floating B8 B9 B10 B11 B12 B13 B14 C1 C3 C7 C8 C9 C10 C11 C12 C13 C14 D1 D2 D3 D12 D13 D14 E1 E2 E3 E12 E13 E14 F1 F2 F3 F12 F13 F14 G1 G2 G12 G13 G14 H1 H2 H3 H12 H13 H14 J1 J2 J3 J12 J13 J14 K1 K2 K3 K12 K13 K14 L1 L2 L3 L12 L13 L14 M1 M2 M3 M7 M8 M9 M10 M11 M12 M13 M14 N1 N3 N6 N7 N8 N9 N10 N11 N12 N13 N14 P1 P2 P8 P9 P11 P12 P13 P14 A6 A7 C5 E5 E8 E9 RFU Reserved for future use E10 F10 G3 G10 H5 Left it floating for future use All rights reserved Transcend and the Transcend logo are registered trademarks of Transcend Information Inc Product offerings and specifications are subject to change without notice All other products brand names company names and logos are trademarks of
22. t at 52MHz Minimum Read MIN _PERF_R_8 26 4 62 R 8h 207 Performance for 8bit at 26MHz for 4bit at 52MHz Minimum Write MIN_PERF_W_4 26 R 8h 206 Performance for 4 bit at 26MHz Minimum Read MIN_PERF_R_4 26 R 8h 205 Performance for 4bit at 26MHz Power class for 26MHz at PWR_CL_26 360 R Oh 203 3 6V1R All rights reserved Transcend and the Transcend log jo are registered trademarks of Transcend Information Inc Product offerings and specifications a re subject to ch ange without notice All other products brand names company nai mes and logos are trademarks of their respective owners Uy Transcend good memories start here www transcend info com Power class for 52MHz at PWR_CL_52_ 360 R Oh 202 3 6V1R Power class for 26MHz at PWR_CL_26 195 R Oh 201 1 95V1R Power class for 52MHz at PWR_CL_52_ 195 R Oh 200 1 95V1R Partition switching timing PARTITION _SWITCH_TIME 3h 199 Out of interrupt busy OUT_OF_INTERRUPT_TIME 2h 198 timing I O driver strength DRIVER_STRENGTH R 1h 197 Device type DEVICE_TYPE R 17h 196 CSD structure version CSD_STRUCTURE R 2h 194 Extended CSD revision EXT_CSD_REV R 6h 192 Command set CMD_SET R W E_P Oh 191 Command set revision CMD_SET_REV R Oh 189 Power class POWER_CLASS R W E_P Oh 187 High speed interface HS_TIMING R W E_P 2h 185 timing Bus widt
23. their respective owners T Transcend good memories start here www transcend info com 153 Ball AA Device Ball Function J5 K6 K7 K10 P7 P10 Symbol Type Card Register eOCR Register For Transcend e MMC the value of 32 bit OCR register is OxCOFF8080 Note OCR bit 31 is set to LOW if the card has not finished the power up routine eCID Register Name Field Width Value CSD slice Manufacturer ID MID 8 1Eh 127 120 Card BGA CBX 2 Oth 113 112 OEM Application ID OID 8 FFh 111 104 Product name PNM 48 5453454D4D43h 103 56 Product revision PRV 8 Counter to indicate FW ver 55 48 Product serial number PSN 32 Random by production 47 16 Manufacturing date MDT 8 Month Year 15 8 CRC7 checksum CRC 7 e Note1 7 1 Note1 The description is the same as e MMC JEDEC standard eCSD Register R Read only W One time programmable and not readable R W One time programmable and readable W E Multiple writable with value kept after power failure H W reset assertion and any CMDO reset and not readable R W E Multiple writable with value kept after power failure H W reset assertion and any CMDO reset and readable ange without notice All other products brand names company names and logos are trademarks of their respective owners All rights reserved Transcend and the Transcend logo are registered trademarks of Transcend Information I
Download Pdf Manuals
Related Search