CRU RAX211-3QR
Contents
1. Limitation of Liability The warranties set forth in this agreement replace all other warranties CRU expressly disclaims all other warranties including but not limited to the implied warranties of merchantability and fitness for a particular purpose and non infringement of third party rights with respect to the documentation and hardware No CRU dealer agent or employee is authorized to make any modification extension or addition to this warranty In no event will CRU or its suppliers be liable for any costs of procurement of substitute products or services lost profits loss of information or data computer malfunction or any other special indirect consequential or incidental damages arising in any way out of the sale of use of or inability to use any CRU product or service even if CRU has been advised of the possibility of such damages In no case shall CRU s liability exceed the actual money paid for the products at issue CRU reserves the right to make modifications and additions to this product without notice or taking on additional liability FCC Compliance Statement This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired opera tion This equipment has been tested and found to comply with the limits for a Class A digital dev2. to connect to your host computer including USB 3 0 which provides up to a b Gbps transfer rate Features e Disk setup is near instantaneous and is capable of JBOD RAID 0 and 1 disk modes e TrayFree Models RAX210 3OR allow for easy insertion and removal of hard drives Models with removable carriers RAX211 3OR enclose and protect hard drives when removed from the RAX enclosure e eSATA FireWire 800 USB 2 0 and USB 3 0 connections are provided for wide variety of connectivity e Specially designed drive and carrier interfaces are built to withstand tens of thousands of insertions e Rugged all metal construction for superior durability Download a copy of the complete User Manual at www cru inc com 1 Installation Steps 1 1 Installing Hard Drives 1 1 1 TrayFree Bay Drive Installation NOTE This subsection refers only to the RAX210 3OR enclosure a b C Pull on the ejection handle to open the door Slide in your SATA hard drive connector end first with the label facing up shut the door by pushing on the handle 1 1 2 Drive Installation for RAX with Removable Carriers NOTE This subsection refers only to the RAX211 3OR g h Slide the drive carrier out of the RAX enclosure The carrier s cover is held in place by a screw on the rear of the unit Remove the screw and then remove the cover slide the drive in from the front of the carrier Mate the connection on the drive with the con
3. Protecting Your Digital Assets Product Models Rex 0 30 RAxXZIIESOR Interface Types amp Speeds e USB 3 0 up to b Gbps e USB 2 0 up to 480 Mbps e eSATA up to 3 Gbps e FireWire 800 up to 800 Mbps Drive Types Supported 3 5 inch SATA Hard Drives Data Connectors e One 1 USB 3 0 2 0 connector e One 1 eSATA connector e Two 2 FireWire 800 connectors RAID Levels JBOD OF 1 Operating System e Windows 8 1 7 Vista or XP Requirements e Windows Server 2012 2008 or 2003 product families e Mac OS X 10 4 x or higher e Linux distributions that support the connection type used Compliance EMI Standard FCC Part 15 Class A CE EMC Standard EN55022 HN55024 Shipping Weights e 17 pounds without drives includes accessories e 23 pounds with drives Dimensions 16 89 x 16 26 x 1 73 429mm x 413mm x 44mm Technical Support Your investment in CRU products is backed up by our free technical support for the lifetime of the product Contact us through our website cru inc com support or call us at 1 800 260 9800 or 1 360 816 1800 2014 CRU Acquisition Group LLC ALL RIGHTS RESERVED RAX and CRU are trademarks of CRU Acquisition Group LLC and are protected by trademark law Product Warranty CRU warrants this product to be free of significant defects in material and workmanship for a period of three years from the original date of purchase CRU s warranty is nontransferable and is limited to the original purchaser
4. ice pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at this own expense In the event that you experience Radio Frequency Interference you should take the following steps to resolve the problem 1 Ensure that the case of your attached drive is grounded 2 Use a data cable with RFI reducing ferrites on each end FE Tested to comply 3 Use a power supply with an RFI reducing ferrite approximately 5 inches from the DC plug 4 Reorient or relocate the receiving antenna FOR OFFICE OR COMMERCIAL USE A9 210 0012 1 Rev 1 0 Protecting Your Digital Assets CRU RAX 30R Rack Enclosure Models Covered RAX210 30R RAX211 30R s DOn Thank you for purchasing CRU s RAX 3OR enclosure The RAX 3OR enclosure is a rack mountable storage enclosure that incorporates removable drive carriers that make it easy to use multiple hard drives in the same enclosure RAX 3OR enclosures provide four connection types that allow you the needed flexibility
5. ke a backup copy of any data you wish to keep before changing the RAID 2 1 Creating a New RAID a b Disconnect the RAX 3OR unit from the computer Insert two hard drives preferably both the same make model and capacity into the RAX 3OR unit and flip the power switch on the rear of the unit After the RAX 3OR unit boots up it will begin alarming and the LCD will display the error Error Not a RAID Set Press the Enter button to silence the alarm Press the Enter button a second time and the LCD screen will ask Make New RAID Press Enter to confirm The LCD will display Select RAID Type Press Up or Down to cycle through to your desired RAID type and press Enter The screen will display Will Erase all Data OK Pressing Enter will result in the loss of all data on the drives Ensure all data is backed up then press Enter The new configuration will be selected and the RAX 3OR unit will reboot The RAID is now created
6. nection on the drive carrier circuit board Flip the drive carrier assembly over and secure the drive in place with the provided screws Attach the Temperature Control Cooling Sensor to the top of the drive with a piece of tape Replace the carrier cover and secure the screw on the rear of the carrier slide the carrier into the RAX enclosure 1 2 Operating Your RAX Enclosure Connect the data cables to the RAX enclosure and your computer Plug in the power cord to a grounded electrical outlet Insert hard drives into the unit and turn on the power For the RAX210 the drives will begin to spin up automatically For the RAX211 use the included set of keys to turn the key 90 degrees clockwise to power on each hard drive NOTE When any hard drives are first used with a RAX 3OR unit they will show up as blank unallocated drives and you ll need to create a RAID inside the unit before you can use it Note that creating a RAID will erase all data on the drive so be sure to back up your data before beginning this operation Your RAX enclosure is now ready to use If the hard drive is already formatted it can be used right away If the hard drives are brand new or their file systems are not compatible with your operating system the drive will need to be formatted before being used 2 RAID Configuration Use the LCD and menu selection buttons to complete these steps Changing RAID levels will erase any data on the drives Ma
Download Pdf Manuals
Related Search