Finisar GBIC 1310nm 10km
Contents
1. Figure 1 GBIC outline drawing Finisar Corporation November 16 2007 Rev A3 Page 8 FTL 1319 3D 2 5 Long Wavelength GBIC Specification November 2007 Finisar X References 1 Gigabit Interface Converter GBIC Revision 5 5 Sun Microsystems Computer Company et al August 16 1999 http playground sun com pub OEmod 2 IEEE Std 802 3 IEEE Standards Department 2002 3 Fibre Channel Physical and Signaling Interface FC PH FC PH2 FC PH3 American National Standard for Information Systems 4 Fibre Channel Draft Physical Interface Specification FC PI 2 Rev 10 0 American National Standard for Information Systems 5 Directive 2002 95 EC of the European Council Parliament and of the Council on the restriction of the use of certain hazardous substances in electrical and electronic equipment January 27 2003 6 AT24C01A 02 04 08 16 2 Wire Serial CMOS E7PROM Atmel Corporation www Atmel com 7 Digital Diagnostics Monitoring Interface for Optical Transceivers SFF Document Number SFF 8472 Revision 9 3 8 Application Note AN 2030 Digital Diagnostic Monitoring Interface for Optical Transceivers Finisar Corporation April 2002 9 Application Note AN 2038 Finisar Implementation of ROHS Compliant Transceivers Finisar Corporation March 2005 XI For More Information Finisar Corporation 1389 Moffett Park Drive Sunnyvale CA 94089 1134 Tel 1 408 548 1000 Fax 12. 80 differential unfiltered Total Transmitter Jitter FT Peak to peak filtered Relative Intensity Noise 120 dB Hz RECEIVER CHARACTERISTICS Optical Input Wavelength in Optical Input Power Pin 18 22 5 3 dBm BER lt 10 w PRBS 2 1 test pattern 2 5Gb s 2 5Gb s 2 125Gb s Total Receiver Jitter 160 ps Peak to peak filtered in loopback Note Parameters are specified over temperature and voltage at end of life unless otherwise noted a Compliant with scaled Table 6 Optical Parameters VI General Specifications Units Notes Conditions Gb sec 10 00 m um Core Single Mode Fiber 225 m 50um 400MHz km Fiber w mode conditioning patch cord for transmitter as specified in IEEE802 3z m IEEE802 3z Note 1 Distances are indicative only Please refer to the Optical Specifications in Section V to calculate a more accurate link budget based on specific conditions in your application 000 225 62 5um 500MHz km Fiber w mode conditioning patch cord for transmitter as specified in Table 7 General Specifications Finisar Corporation November 16 2007 Rev A3 Page 5 FTL 1319 3D 2 5 Long Wavelength GBIC Specification November 2007 Finisar VII Environmental Specifications Parameter i Units Notes Conditions Operatu Teup C Case Teper ae C Renee SiorgeTemp Tw 0 se Safety a and IEC 825 Class 1 Laser Product See Note 1
3. 408 541 6138 sales finisar com www finisar com Finisar Corporation November 16 2007 Rev A3 Page 9
4. Finisar Product Specification RoHS Compliant Long Wavelength GBIC Transceiver FTL 1319 3D 2 5 Product Features e Up to 2 5Gb s bi directional data links e 1310nm Fabry Perot laser transmitter e Optional Digital Diagnostics e Extended operating temperature range 10 C to 85 C Applications e Compatible with 3 3 amp 5V 1 25Gb s 1000BASE LX Systems Ethernet e Hot pluggable complies with j a payee TIGE GBIC specification Rev 5 5 e Fully metallic enclosure for low EMI e Low power dissipation e RoHS compliant and Lead Free Finisar s FTL 1319 3D 2 5 1310nm GBIC transceivers comply with GBIC Specification Revision 5 5 in all respects expect where deviations are required to accommodate the higher bit rate They are compatible with Gigabit Ethernet as specified in IEEE 802 3 Fibre Channel FC PH PH2 PH3 and FC PI 2 Rev 10 0 They are RoHS compliant and lead free per Directive 2002 95 EC and Finisar Application Note AN 2038 Finisar Corporation November 16 2007 Rev A3 Page 1 FTL 1319 3D 2 5 Long Wavelength GBIC Specification November 2007 Finisar I Pin Out np oxo moo MOD DEFO MOD_DEF 2 2 3 4 5 CTX DISABLE 7 oa e TX_FAULT 10 not supported GND Table 1 GBIC to host connector pin assignment Sequence indicates the order in which pins make contact when the device is hot plugged See Table 3 Signal Definitions in the GBIC Specification R
5. Note 1 Complies with FDA performance standards for laser products except for deviations pursuant to Laser Notice No 50 dated July 26 2001 Table 8 Environmental specifications VIII Serial Communication Protocol All Finisar optical GBICs implement serial identification features described for Module Definition 4 as outlined in Annex D of the GBIC Specification These GBICs use an Atmel AT24C01A 128 byte E7PROM at address AOH For details on interfacing with the E PROM see the Atmel data sheet titled AT24C01A 02 04 08 16 2 Wire Serial CMOS E PROM The FTR 1319 3D 2 5 also supports extended diagnostic features as described in Finisar Applications Note AN 2030 Digital Diagnostic Monitoring Interface for Optical Transceivers and additional information is available in SFF standard titled Digital Diagnostic Monitoring Interface for Optical Transceivers SFF 8472 rev9 3 A controller IC that monitors system parameters such as laser current module temperature transmitter power and received power is accessible at address A2H I2C clock speed digital diagnostic accuracy and digital diagnostic range can be found in the table below Values in the table represent the worst case values over temperature voltage and life Finisar Corporation November 16 2007 Rev A3 Page 6 FTL 1319 3D 2 5 Long Wavelength GBIC Specification November 2007 Finisar Para
6. evision 5 5 Finisar Corporation November 16 2007 Rev A3 Page 2 FTL 1319 3D 2 5 Long Wavelength GBIC Specification November 2007 Finisar II Electrical Power Interface Finisar FTL 1319 3D 2 5 GBICs have an extended power supply voltage range of 3 15 V to 5 5 V as described in Table 2 They are compatible with both 3 3V and 5 V systems Parameter Notes Conditions Supply Current state current Sad a continuosly Table 2 Electrical power interface III Low Speed Signals RX_LOS and TX_DISABLE are TTL signals as described in Table 3 MOD_DEF 1 SCL and MOD_DEF 2 SDA are open drain CMOS signals see section VII Serial Communication Protocol Both MOD_DEF 1 and MOD_DEF 2 must be pulled up to host_Vcc For more detailed information see sections 5 3 1 5 3 8 in the GBIC Specification Rev 5 5 Parameter Notes Conditions GBIC Output LOW 4 7k to 10k pull up to host_Vcc measured at host side of connector GBIC Output HIGH Vou host_Vcc 0 5 host_Vcc 0 3 V 4 1k to 10k pull up to host_Vcc measured at host side of connector GBIC Input LOW V V 4 7k to 10k pull up to Vcc measured at GBIC side of connector GBIC Input HIGH 4 7k to 10k pull up to Vcc measured at GBIC side of connector Table 3 Low speed signals electronic characteristics Finisar Corporation November 16 2007 Rev A3 Page 3 FTL 1319 3D 2 5 Long Wavelength GBIC Specification November 2007 Fini
7. meter Symbol Min Typ Max Units Notes Conditions TC Clock Speed 0 100 000 Hz Bus can be driven blind Accuracy Internal Transceiver DD qemperature 3 3 C Measured at controller IC Temperature Internal Transceiver DDvottage 3 3 Measured at controller IC Supply Voltage Tx Bias Current DDgias 10 10 Tx Output Power DD py Power 3 3 dB 100 tested in production tested at room temp to 2 dB Received Average DDaxpower 3 3 dB 100 tested in production Power tested at room temp to 2 dB Range Internal Transceiver DD Temperature 40 100 C Temperature Internal Transceiver DD otiage 3 0 6 0 V Supply Voltage Tx Bias Current DDgias 0 80 mA Tx Output Power DD pypower 13 5 1 dBm Received Average DDrxpower 24 1 dBm Power Finisar Corporation November 16 2007 Rev A3 Table 9 Digital Diagnostic Accuracy and Range Limits Page 7 FTL 1319 3D 2 5 Long Wavelength GBIC Specification November 2007 Finisar IX Mechanical Specifications Finisar GBICs are compatible with the mechanical specifications outlined in the GBIC Specification Revision 5 5 Section 6 Parameter GBIC insertion F GBIC retention FR Table 10 Insertion extraction and retention forces 1 03 REF I SINGLE MODE 5 1310 nm FTL 1319 3D 2 5 2 57 REF ai jan es 000 1 2 006 z T k 393 005 Gel 47 003 m 2 25 010
8. sar Parameter i Units Notes Conditions RX_LOS Assert Level a E RXLOSHysteresis os _ RX_LOS Assert Delay t_loss_on 100 usec 8 detection es loss of signal to assertion of RX_LOS RX_LOS Pree Delay t_loss peace I faa usec From detection of presence of signal to negation of RX_LOS ieee _DISABLE Assert Time t_ ie usec Rising edge of TX_DISABLE to fall of output signal below 10 of nominal TX_DISABLE Negate Time a 1000 usec Falling edge of TX_DISABLE to rise of output signal above 90 of nominal TX_DISABLE Reset Time t_reset 10 usec TX_DISABLE HIGH before TX_DISABLE set LOW Table 4 Low speed signal parameters IV High Speed Electrical Interface All high speed PECL signals are AC coupled internally Parameter i i Notes Conditions Data Input Voltage PECL differential peak peak Data Onpui Voltage v o 2000 mV O PECL differential peak peak a a e BicErorRate se o PRBS 2 T test data pater O Z S om Rx Output impedance Zn 75 om SSS Table 5 High speed Electrical Interface Finisar Corporation November 16 2007 Rev A3 Page 4 FTL 1319 3D 2 5 Long Wavelength GBIC Specification November 2007 Finisar vV Optical Parameters Units Notes Conditions T Transmitter Optical Output Power T ransmitter Extinction Ratio ransmitter Spectral Width nm i i 3 dBm Average power coupled into single mode fiber FC and 2xGE eye 160 ps 20
Download Pdf Manuals
Related Search