Finisar GBIC 1310nm 10km
Contents
1. Parameter Symbol Min Typ Max Units Notes Conditions TC Clock Speed 0 100 000 Hz Bus can be driven blind Accuracy Internal Transceiver DD qemperature 3 3 C Measured at controller IC Temperature Internal Transceiver DDvottage 3 3 Measured at controller IC Supply Voltage Tx Bias Current DDgias 10 10 Tx Output Power DD py Power 3 3 dB 100 tested in production tested at room temp to 2 dB Received Average DDaxpower 3 3 dB 100 tested in production Power tested at room temp to 2 dB Range Internal Transceiver DD Temperature 40 100 C Temperature Internal Transceiver DD otiage 3 0 6 0 V Supply Voltage Tx Bias Current DDgias 0 80 mA Tx Output Power DD pypower 13 5 1 dBm Received Average DDrxpower 24 1 dBm Power Finisar Corporation November 16 2007 Rev C3 Table 9 Digital Diagnostic Accuracy and Range Limits Page 7 FTL 1319 3D Long Wavelength GBIC Specification November 2007 Finisar IX Mechanical Specifications Finisar GBICs are compatible with the mechanical specifications outlined in the GBIC Specification Revision 5 5 Section 6 Parameter GBIC insertion GBIC extraction GBIC retention PIN 10 PIN 1 Figure 1 GBIC outline drawing Finisar Corporation November 16 2007 Rev C3 Page 8 FTL 1319 3D Long Wavelength GBIC Specification November 2007 Finisar X References 1 Gigabit Interfa2. Corporation November 16 2007 Rev C3 Page 2 FTL 1319 3D Long Wavelength GBIC Specification November 2007 Finisar II Electrical Power Interface Finisar FTL 1319 3D GBICs have an extended power supply voltage range of 3 15 V to 5 5 V as described in Table 2 They are compatible with both 3 3V and 5 V systems Notes Conditions I 200 300 mA Inrush Current Tyurge 30 mA Hot plug above steady state current Absolute Supply Voltage Vmax 0 3 V Not to be applied continuosly Table 2 Electrical power interface III Low Speed Signals RX_LOS and TX_DISABLE are TTL signals as described in Table 3 MOD_DEF 1 SCL and MOD_DEF 2 SDA are open drain CMOS signals see section VII Serial Communication Protocol Both MOD_DEF 1 and MOD_DEF 2 must be pulled up to host_Vcc For more detailed information see sections 5 3 1 5 3 8 in the GBIC Specification Rev 5 5 Parameter Units Notes Conditions GBIC Output LOW 4 7k to 10k pull up to host_Vcc measured at host side of connector GBIC Output HIGH Vou host_Vcc 0 5 host_Vcc 0 3 V 4 7k to 10k pull up to host_Vcc measured at host side of connector GBIC Input LOW V V 4 7k to 10k pull up to Vcc measured at GBIC side of connector GBIC Input HIGH Vin 2 Vec 0 3 V 4 7k to 10k pull up to Vcc measured at GBIC side of connector Table 3 Low speed signals electronic characteristics Finisar Corporation November 16 2007 Rev C3 Page 3
3. Product See Note 1 Note 1 Complies with FDA performance standards for laser products except for deviations pursuant to Laser Notice No 50 dated July 26 2001 Table 8 Environmental specifications VIII Serial Communication Protocol All Finisar optical GBICs implement serial identification features described for Module Definition 4 as outlined in Annex D of the GBIC Specification These GBICs use an Atmel AT24C01A 128 byte E7PROM at address AOH For details on interfacing with the E PROM see the Atmel data sheet titled AT24C01A 02 04 08 16 2 Wire Serial CMOS EPROM The FTL 1319 3D DD also supports extended diagnostic features as described in Finisar Applications Note AN 2030 Digital Diagnostic Monitoring Interface for Optical Transceivers and additional information is available in SFF standard titled Digital Diagnostic Monitoring Interface for Optical Transceivers SFF 8472 rev9 3 A controller IC that monitors system parameters such as laser current module temperature transmitter power and received power is accessible at address A2H I2C clock speed digital diagnostic accuracy and digital diagnostic range can be found in the table below Values in the table represent the worst case values over temperature voltage and life Finisar Corporation November 16 2007 Rev C3 Page 6 FTL 1319 3D Long Wavelength GBIC Specification November 2007 Finisar
4. FTL 1319 3D Long Wavelength GBIC Specification November 2007 Finisar Parameter i Units Notes Conditions RX_LOS Assert Level a E RXLOSHysteresis os _ RX_LOS Assert Delay t_loss_on 100 usec 8 detection es loss of signal to assertion of RX_LOS RX_LOS Pree Delay t_loss peace I faa usec From detection of presence of signal to negation of RX_LOS ieee _DISABLE Assert Time t_ ie usec Rising edge of TX_DISABLE to fall of output signal below 10 of nominal TX_DISABLE Negate Time a 1000 usec Falling edge of TX_DISABLE to rise of output signal above 90 of nominal TX_DISABLE Reset Time t_reset 10 usec TX_DISABLE HIGH before TX_DISABLE set LOW Table 4 Low speed signal parameters IV High Speed Electrical Interface All high speed PECL signals are AC coupled internally Parameter i i Notes Conditions Data Input Voltage PECL differential peak peak Data Onpui Voltage v o 2000 mV O PECL differential peak peak PECL sal a 1 e ae BicErorRate se o PRBS 2 T test data pater O S S om x Output impedance Zon 73 om SSS Table 5 High speed electrical interface Finisar Corporation November 16 2007 Rev C3 Page 4 FTL 1319 3D Long Wavelength GBIC Specification November 2007 Finisar vV Optical Parameters Units Notes Conditions TRANSMITTER CHARACTERISTICS Transmitter Center Wavelength Transmitter Spectral Width A nm RMS Also meets curves i
5. Finisar Product Specification RoHS Compliant Long Wavelength GBIC Transceiver FTL 1319 3D PRODUCT FEATURES e Upto 1 25Gb s bi directional data links e 1310nm Fabry Perot laser transmitter e RoHS Compliant and Lead Free e Optional Digital Diagnostics e Extended operating temperature range 10 C to 85 C APPLICATIONS C tible with 3 3 amp 5V ae D e 1 0625 Gb s Fibre Channel e Hot pluggable complies with e 1 25 Gigabit Ethernet GBIC specification Rev 5 5 e Fully metallic enclosure for low EMI e Low power dissipation Finisar s FTL 1319 3D 1310nm GBIC transceivers comply with GBIC Specification Revision 5 5 They are compatible with Gigabit Ethernet as specified in IEEE 802 3 Fibre Channel FC PH PH2 PH3 and FC PI 2 Rev 10 0 They are RoHS compliant and lead free per Directive 2002 95 EC and Finisar Appl Note AN 2038 PRODUCT SELECTION Part Number Digital Diagnostics FTL 1319 3D No FTL 1319 3D DD Yes Finisar Corporation November 16 2007 Rev C3 Page 1 FTL 1319 3D Long Wavelength GBIC Specification November 2007 Finisar I Pin Descriptions B ae e a 2 3 4 Tx DISABLE 7 pox TX_FAULT 10 not supported GND Table 1 GBIC to host connector pin assignment Sequence indicates the order in which pins make contact when the device is hot plugged See Table 3 Signal Definitions in the GBIC Specification Revision 5 5 Finisar
6. ce Converter GBIC Revision 5 5 Sun Microsystems Computer Company et al August 16 1999 http playground sun com pub OEmod 2 IEEE Std 802 3 IEEE Standards Department 2002 3 Fibre Channel Physical and Signaling Interface FC PH FC PH2 FC PH3 American National Standard for Information Systems 4 Fibre Channel Draft Physical Interface Specification FC PI 2 Rev 10 0 American National Standard for Information Systems 5 Directive 2002 95 EC of the European Council Parliament and of the Council on the restriction of the use of certain hazardous substances in electrical and electronic equipment January 27 2003 6 AT24C01A 02 04 08 16 2 Wire Serial CMOS E7PROM Atmel Corporation www Atmel com XI For More Information Finisar Corporation 1389 Moffett Park Drive Sunnyvale CA 94089 1134 Tel 1 408 548 1000 Fax 1 408 541 6138 sales finisar com www finisar com Finisar Corporation November 16 2007 Rev C3 Page 9
7. n FC PI 10 0 Figures 18 re ee into aaa mode fiber Transmiter Extinction Ratio OM 9 Tammie Eye Opening Channel Eye Masks Transmitter Rise Fall Time tr tf 20 80 differential unfiltered ae rt eee Relative Intensity Noise 120 dB Hz RECEIVER CHARACTERISTICS Optical Input Wavelength es a O T a O e Optical mpu Power 2568A Pa 9 f 3 f abm BER 10 w PRES Onenen Poner CS e a fsa 27 1 test pattern Total Receiver Jitter Peak to peak filtered in loopback Note Parameters are specified over temperature and voltage at end of life unless otherwise noted Table 6 Optical parameters Units Notes Conditions Gb sec Fibre Channel IEEE 802 3 Compatible Foer j ooo m foum Core Single Mode Fiber Fibertensth L __ 350 m opm s00MHzkm Fiber Fibertensth Fiber Length L 275 m 62 5um200MHzkmFiber_ Table 7 General specifications Finisar Corporation November 16 2007 Rev C3 Page 5 FTL 1319 3D Long Wavelength GBIC Specification November 2007 Finisar VII Environmental Specifications Note that the GBIC Specification requires an ambient temperature range of 0 to 50 C The FTL 1319 3D has an extended range from 10 C to 85 C case temperature as specified in Table 8 Parameter i Units Notes Conditions npon ey C Case Tipsy Rai iy Rt 0 Ren eg StorageTemp Tw 0 fes C mo Safety a and IEC 825 Class Laser
Download Pdf Manuals
Related Search