Home

High Power PP-750 Pro

1. 54 3P SHEET METAL TOLERANCE UNLESS OTHERWISE SPECIFIED PARTS LIST Je aiaa a aa APPROVED CHECKED DESIGNED WR 8 lt x lt 25 Hh He AA HIGH POWER 25cx lt 100 2015 025 sose sq20t1t0311 Tome HIGH POWER ELECTRONIC CO LTD meco aa as ar Ne seva o oo SL uNTmm qn Poe Do ee MODEL NAME 91 75032 U01 ACPESGHE SF Q D P 0010405
2. Relative Humidity 20 to 95 noncondensing 6 2 Altitude The power supply can operate normally at any altitude between 0 to 10000 feet 6 33 Vibration and Shock Sweep and resonance search for each of X Y Z axis at the sweep RATE of 1 OCTAVE Min Amplitude 5 55 10 Hz 7 Conducted EMI 8 Product Safety 8 1 Safety Requirement TUV CB 8 2 Leakage Current The AC leakage current is less than 3 5mA when the power supply connect to 264Vac S0Hz 8 3 Insulation Resistance The insulation resistance should be not less than 30M ohm after applying of 500VDC for 1 minute 8 4 Dielectric Voltage Withstand The power supply shall withstand for 1 minute without breakdown the application of a 60Hz 1500V AC voltage applied between both input line and chassis 20mA DC cut off current Main transformer shall similarly withstand 3000Vac applied between both primary and secondary windings for a minimum of one minute Page 8 N HIGH POWER ELECTRONIC CO LTD Switching Power Supply Specifications 9 Power Good Signal A TTL compatible signal for the purpose of initiating an orderly start up procedure under normal input operating conditions During power up this signal is asserted low until 5V is under regulation and AC reaches min line specification range After all voltage are going appropriate level the system may have a turn on delay of 100mS but no greater than 500mS During power off the signal should go to low level before 5V is ou
3. WO AH POER ELECTRONIC co LTD Part Name 91 75032 U01 Model No HPC 750 B14S Document Version 01 PRODUCT SPECIFICATION Release Date 201 1 4 14 Approved by Checked by Prepared by HIGH POWER ELECTRONIC CO LTD SIRFA International Co Ltd TEL 886 2 2659 2535 TEL 86 769 87720745 Fax 886 2 2659 2265 Fax 86 769 87915210 WO z POER ELECTRONIC co LTD Switching Power Supply Specifications Subject Change History of Specification 53 rs A hig Bel oR AN A REF NO JA LAI 2011 4 14 01 initial Page 1 N HIGH POWER ELECTRONIC CO LTD Switching Power Supply Specifications Table of Contents General 1 1 Scope Input Characteristics 2 1 Input Voltage 2 2 Input Frequency 23 Max Input AC Current 2 4 Inrush Current 2 5 Efficiency Output characteristics 3 1 Nominal Operation Output 3 2 Remote On Off controlled mode 3 3 Regulation 3 4 Rise Time 3 5 Hold up Time 3 6 5 VSB 3 7 PG OK 3 8 3 3V Sense 3 9 Capacitive Load Protection 4 1 Input Protection 42 Output Protection Start Stability 5 1 No Load Start 522 Cold Start Environments 6 1 Temperature and Humidity 6 2 Altitude 63 Vibration and Shock Page 2 WO z POER ELECTRONIC co LTD Switching Power Supply Specifications 7 Conducted EMI 8 Prod
4. age 11 N HIGH POWER ELECTRONIC CO LTD Switching Power Supply Specifications 14 3 7 PCI Power Connector PD PD1 PE PE1 Connector MOLEX 88751 or equivalent Pin Signal 18 AWG Wire 12V DC 12V DC 12V DC COM COM COM COM COM 14 3 8 12V Power Connector PB PC Connector Molex 39 01 2040 or equivalent Pin Signal 18 AWG Wire 1 COM Black 2 COM Black 3 COM Black 4 COM Black 5 12 V DC Yellow 6 12 V DC Yellow 7 12 V DC Yellow 8 12 V DC Yellow Page 12 COLOR V COLOR ORANGE 3 3V ORANGE ORANGE 3 3V BLACK BLACK COM RED RED 5V BLACK BLACK COM YELLOW RED 5V YELLOW BLACK COM BLACK GRAY PWR_OK BLACK PURPLE 5VSB RED YELLOW 12V RED oe Von BONS o von ORANGE 3 3V BLACK BROWN 3 3V SENSE BLACK BLUE 12V YELLOW BLACK COM BLACK GREEN PS_ON BLACK BLACK COM BLACK aone o Von BONS NDN BLACK COM BLACK BLACK COM YELLOW YELLOW B B A r As His RED YELLOW RED YELLOW YELLOW YELLOW ORANGE YELLOW RED YELLOW BLACK BLACK com 5 BLACK COM ES s Bracs com p Bracs com e com BLACK COM EE 254x3P Aw ase otf SS 13 J 2
5. d range 3 4 Rise Time DC output rise time is less than 20 mS at nominal line and full load 3 5 Hold up Time DC 5V output maintains at least 12mS after power off which hold within para 3 1 under 115V 60Hz and 230V 50Hz condition Page 5 N HIGH POWER ELECTRONIC CO LTD Switching Power Supply Specifications 3 6 5VSB 5VSB is requierd for the implementation of PS ON described above 5VSB is a standby voltage that may be used to power circuits that require power input during the powered down state of all power rails The 5 VSB pin should deliver 5V 5 at a minimum of 3 0 A for PC board circuits to operate Conversely PC board should draw no more than 3 0A maximum form this pin This power may be used to operate circuits such as soft power control 3 7 PG OK PG OK is a power good signal and should be asserted high by power supply to indicate that the 5 VDC and 3 3 VDC outputs are above the under voltage thresholds of the power supply When this signal is asserted high there should be sufficient mains energy stored by the converter to guarantee continuous power operation within specification Conversely when either the 5VDC or the 3 3VDC output voltage falls below the under voltage threshold or when mains power has been removed for a time sufficiently long so that power supply operation is no longer guaranteed PG OK should be deasserted to a low state See Figure 1 for a representation of the timing characteristics of t
6. he PG OK PS ON and germane power rail signals 3 8 3 3V Sense A default 3 3V sense line should be implemented pin 13 of the connector 3 9 Capacitive Load The power supply should be able to power up and operate normally with the following capacitances simultaneously present on the DC outputs Output Capacitive load uF 5V 6 000 12V1 5 000 12V2 3 000 3 3V 6 000 12V 350 5VS 350 4 Protection 4 1 Input Protection In primary circuit of the power supply a protected fuse is inserted Only internal fault of the power supply will cause the fuse blown Any overload or short circuit at DC output will keep from fuse brown or fire hazard Page 6 N HIGH POWER ELECTRONIC CO LTD Switching Power Supply Specifications 4 2 Output Protection 4 2 1 Under voltage protection The 5V 12V 3 3V DC output are protected against the under voltage condition range value can t be exceed 3 3 3 7V at 5V terminal and 8 5 9 5V at 12V 2 0 2 4V at 3 3V 4 2 2 Over Voltage Protection The 5V 12V 3 3V DC output are protected against the over voltage condition Maximum value can t be over 6 5V at 5V terminal and 15 5V at 12V 4 3V at 3 3V 4 2 3 Over Power Protection The power supply can be used electronic circuit to limit the output current against exceeding 60 of surge output power or protected against excessive power delivery since short circuit of any output or over total power at high line 4 2 4 Sh
7. ng input fuse bulk rectifiers and surge limiting device 2 5 Efficiency HPC 750 B14S provides an efficiency of 82 minimum when measured at full load under 115V 60Hz and 230V 50Hz condition Page 4 N HIGH POWER ELECTRONIC CO LTD Switching Power Supply Specifications 3 Output characteristics 3 1 Normal Operation Output Output Load Range Ripple P P Ripple amp Noise MIN MAX EP Max 02A 220A 100mV 2 12V 06A 54 0A 120mV 200mV 3 12V 0 0A 0 3A 150mV 200mV 00A 30A 100mV 5 3 3V 01A 220A 100mV Maximum continuous total DC output power should not exceed 750W Maximum continuous combined load on 3 3VDC and 5VDC outputs shall not exceed 130W Maximum combined load on 12V outputs shall not exceed 648W NOTE Noise test should be measured with 20 MHz bandwidth frequency oscilloscope The output terminal shall add a tantalum capacitor of 10uF in parallel with a ceramic capacitor of 0 1uF 3 2 Remote On Off Controlled mode The PSON signal is required to remotely turn on off the power supply PSON is an active low signal that turns on the output power rails When this is not pulled low by the system or left open the outputs except the 5VSB turn off This signal is pulled to a standby voltage by a pull up resistor internal to the power supply TTL level H 2 0 V 5 25 V L 0 0 V 1 0 V 3 3 Regulation The cross regulation defined as follows the output regulation should be within the specifie
8. ort Circuit Protection Short circuit placed on 5V 12V 3 3V 12V will latch off 5VSB will auto recovery 4 2 5 Over Current Protection Current protection should be designed to limit the current to operate within safe operating conditions Over current protection schemes where only the voltage output that experiences the over current event is shut off may be adequate to maintain safe operation of the power supply and the system however damage to the motherboard or other system components may occur The recommended over current protection scheme is for the power supply to latch into the shutdown state The setting of over current protection for each output rail is as following 4 2 6 Over Temperature Protection This power supply includes an over temperature protection sensor which can trip and shut down the power supply at 110 C 5 Start Stability 5 1 No Load Start When power is applied to HPC 750 B 14S with no load connected or under minimum load connected neither damage to power supply nor hazards to users will occur 5 2 Cold Start The power supply shall operate properly when first applied at normal input voltage and or so maximum load after 4 hours storage in 0 C environment Page 7 N HIGH POWER ELECTRONIC CO LTD Switching Power Supply Specifications 6 Environments 6 1 Temperature and Humidity 6 1 1 Operating Temperature 0to450C See Figure 2 Relative Humidity 20 to 90 6 1 2 Storage Temperature 40 to 70 C
9. t Maximum weight is 1 7 Kgs 14 3 Pin Designation 14 3 1DC CONNECTOR REQUIREMENTS List or recognized component appliance wiring material AVLV2 gt CN gt rated min 85 C gt 300VAC shall be used for all output wiring Page 10 N HIGH POWER ELECTRONIC CO LTD Switching Power Supply Specifications 14 3 2 BASEBOARD CONNECTOR PA1 20P RA Connector MOLEX 39 01 2200 or Approved Equivalent 18 AWG Wire Signal Pin Pin Signal 18 AWG Wire Orange 3 3 VDC 13 1 3 3 VDC Orange Brown 22AWG 3 3V SENSE Blue 12 VDC 14 2 3 3 VDC Orange Black COM 15 3 COM Black Green 2OAWG PS ON 16 4 5 VDC Red Black COM 17 5 COM Black Black COM 18 6 5 VDC Red Black COM 19 7 COM Black 20 8 PWR_OK Gray 20 AWG Red 5 VDC 21 9 5VSB Purple 16A WG Red 5 VDC 22 10 12 V DC Yellow PA2 4P Red 5 VDC 23 11 12 VDC Yellow Black COM 24 12 3 3 VDC Orange 14 3 3 Peripheral Connectors PH PH1 Connector AMP 1 480424 0 or MOLEX Connector AMP 171822 4 or approved 8981 04P or approved equivalent equivalent Contacts AMP 61314 1 terminals or equivalent Pin Signal 20 AWG Wire Pin Signal 22 AWG Wire 12 V DC Yellow 1 5 VDC Red COM Black 2 COM Black COM Black 3 COM Black 5 VDC Red 4 412VDC Yellow 14 3 4 Serial ATA Power Connector PF PG Connector MOLEX 88751 or equivalent Pin Signal 18 AWG Wire 1 3 3VDC Orange 2 COM Black 3 5 VDC Red 4 COM Black 5 12VDC Yellow P
10. t of regulation The low level is O to 0 8V and high level is 4 75 to 5 25V The Power Good signal can drive up to 6 standard TTL loads Time Diagram Figure AC OFF AC AC ON 15s PS ON OFF POWER ON POWER OFF 4 75 pD 25V eM 5Y OFP fa T4 T3 T5 i Tl Power Good Ts T2 T1 Turn on time 2 sec Max T2 Rise time lt 20mS Max T3 Power good turn on delay time 100 lt T3 lt 500 mS T4 Switch on time 0 5 sec Max T5 Power good turn off delay time 1 0 mS Min PS ON OFF T6 Power hold on time 12 mS Min Power on off cycle When the power supply is turned off for a minimum of 2 0 sec and turn on again the power good signal will be asserted Page 9 N HIGH POWER ELECTRONIC CO LTD Switching Power Supply Specifications 10 MTBF The MTBF of the power should be 100 000 hours min 11 Burn In 11 1 Input Voltage Applying 220Vac for 230V model 11 2Test Condition Applying 75 loads for the power supply in 45 5 C chamber for 4 hours 12 Harmonics The product shall meet requirement for EN61000 3 2 amp EN61000 3 3 1995 standard of class D test at 230Vac 50Hz 13 Power Factor The power supply with active power factor correction and meet the EN61000 3 2 standards The power factor is greater than 0 9 at 230V SOHz Max load 14 Mechanical Specification 14 10utline Dimension Please refer the mechanical drawing of HPC 750 B14S 14 2 Weigh
11. uct Safety 8 1 8 2 8 3 8 4 Safety Requirement Leakage Current Insulation Resistance Dielectric Voltage Withstand 9 Power Good Signal 10 MTBF 11 Burn In 11 1 Input Voltage 11 2 Test Condition 12 Harmonics 13 Power Factor 14 Mechanical Specification 14 1 Outline Dimension 14 2 Weight 14 3 Pin Assignment Page 3 N HIGH POWER ELECTRONIC CO LTD Switching Power Supply Specifications 1 General 1 1 Scope This specification defines the performance characteristics of a single phase 750 watts 6 output power supply This specification also defines worldwide safety and electromagnetic compatibility requirements for the power supply which is intended for use in computer products 2 Input Characteristics 2 1 Input Voltage Nominal Voltage Voltage Variation Range 100 240 Vrms 90 264 Vrms 2 2 Input Frequency Nominal Frequency Frequency Variation Range 50 60 Hz 47 Hz to 63 Hz The power supply must operate at above frequency with 90 264 VACrms input voltage range 2 3 Max Input AC Current Max Input Current Measuring Range 10A 90 264 Vrms 2 4 Inrush Current The power supply must meet inrush requirements for any rated AC voltage during turn on at any phase of AC voltage during a single cycle AC dropout condition during repetitive ON OFF cycling of AC and over the specified temperature range The peak inrush current shall be less than the ratings of its critical components includi

High Power PP-750 Pro

Contents

Download Pdf Manuals

Related Search

Related Contents