WatchGuard Ethernet Power Injector
Contents
1. 30 Declaration of Conformity Declaration of Conformity WatchGuard Technologies Inc hereby declares that the product s listed below conform to the European Union directives and standards identified in this declaration Product s Wireless Access Point Model AP100 amp AP200 EU Directive s Radio amp T l communications Terminal Equipment 1999 5 Low Voltage 2006 95 EC Electromagnetic Compatibility 2004 108 EC Energy related Products 2009 125 EC Common Standard s EN 60950 1 2006 Am11 2009 Am1 2010 Am12 2011 Safety of ITE EN 55022 2010 Class A Emissions for ITE EN 55024 2010 Immunity for ITE EN 61000 3 2 2006 A1 2009 A2 2009 Harmonics EN 61000 3 3 2008 Flicker Wireless Standard s EN 301 489 01 v1 9 2 2011 09 EMC and Radio Spectrum Matters EN 301 489 17 v2 1 1 2009 05 EMC and Radio Spectrum Matters EN 300 328 v1 7 1 2006 10 Radio Spectrum Matters EN 301 893 v1 6 1 2011 11 Broadband Radio Access Networks In accordance with the Radio and Telecommunications Terminal Equipment Act FTEG and Directive 1999 5 EC R amp TTE Directive Manufacturer Hersteller WatchGuard Technologies 505 5 Ave S Suite 500 Seattle WA 98104 Radio Equipment Funkanlage Wireless Access Point Type Designation Typenbezeichnung 100 amp AP200 Specifications Technisc2. OSM VCCI Notice Class A ITE Japan CORB FRA BERIILENSBETI 05286 73073128 95 84 0 3 6 FOET 29 France i les dispositifs fonctionnant dans la bande 5150 5250 MHz sont r serv s uniquement pour une utilisation a l int rieur afin de r duire les risques de brouillage pr judiciable aux syst mes de satellites mobiles utilisant les m mes canaux ii De plus les utilisateurs devraient aussi tre avis s que les utilisateurs de radars de haute puissance sont d sign s utilisateurs principaux c d qu ils ont la priorit pour les bandes 5 250 5 350 MHz et 5 650 5 850 MHz et que ces radars pourraient causer du brouillage et ou des dommages aux dispositifs LAN EL Korea sid SAAS 22S AWESA ASO VS Mexico de este equipo esta sujeta a las siguientes dos condiciones 1 es posible que este equipo dispositivo no cause interferencia perjudicial y 2 este equipo o dispositivo debe aceptar cualquier interferencia incluyendo la que pueda causar su propia operaci n no deseada Taiwan Class A Type Device
3. SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES 37
4. WatchGuard web site that is used herein are either registered trademarks or trademarks of WatchGuard Technologies Inc and or its subsidiaries in the United States and or other countries All other trademarks are the property of their respective owners Part Number 352 4257 001 Rev C Revised June 26 2013 You can find all WatchGuard documentation online at http www watchguard com help documentation Notice to Users Information in this guide is subject to change without notice Updates to this guide are posted at http www watchguard com help documentation ap asp Companies names and data used in examples herein are fictitious unless otherwise noted No part of this guide may be reproduced or transmitted in any form or by any means electronic or mechanical for any purpose without the express written permission of WatchGuard Technologies Inc Introduction The WatchGuard AP family of wireless access points provide secure reliable wireless communications while delivering high performance and broad coverage a perfect combination of services that will meet the needs of enterprise level customers small businesses branch offices campuses and hotels alike WatchGuard AP devices feature 2x2 MIMO Multiple Input Multiple Output capability and 802 11 a b g n wireless coverage and operate on both 2 4GHz b g n and 5GHz a n spectrums to provide users with enhanced reliability and performance Internal antennas slim ca
5. WiftchGuard WatchGuard AP Setup Guide AP 100 AP 200 About WatchGuard WatchGuard offers affordable all in one network and content security solutions that provide defense in depth and help meet regulatory compliance requirements The WatchGuard XTM line combines firewall VPN GAV IPS spam blocking and URL filtering to protect your network from spam viruses malware and intrusions The new XCS line offers email and web content security combined with data loss prevention WatchGuard extensible solutions scale to offer right sized security ranging from small businesses to enterprises with 10 000 employees WatchGuard builds simple reliable and robust security appliances featuring fast implementation and comprehensive management and reporting tools Enterprises throughout the world rely on our signature red boxes to maximize security without sacrificing efficiency and productivity For more information call 206 613 6600 or visit www watchguard com Address 505 Fifth Avenue South Suite 500 Seattle WA 98104 Support www watchguard com support U S and Canada 877 232 3531 All Other Countries 1 206 521 3575 Sales U S and Canada 1 800 734 9905 All Other Countries 1 206 613 0895 Copyright Information Copyright 2012 2013 WatchGuard Technologies Inc All rights reserved WatchGuard the WatchGuard logo LiveSecurity and any other mark listed as a trademark in the Terms of Use portion of the
6. any patent must be licensed for everyone s free use or not licensed at all The precise terms and conditions for copying distribution and modification follow Terms and Conditions for Copying Distribution and Modification 1 This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License The Program below refers to any such program or work and a work based on the Program means either the Program or any derivative work under copyright law that is to say a work containing the Program or a portion of it either verbatim or with modifications and or translated into another language Hereinafter translation is included without limitation in the term modification Each licensee is addressed as you Activities other than copying distribution and modification are not covered by this License they are outside its scope The act of running the Program is not restricted and the output from the Program is covered only if its contents constitute a work based on the Program independent of having been made by running the Program Whether that is true depends on what the Program does 2 You may copy and distribute verbatim copies of the Program s source code as you receive it in any medium provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warra
7. as applicable 1 LIMITED WARRANTY WatchGuard warrants that upon delivery and for one 1 year thereafter the Warranty Period a the Product will be free from material defects in materials and workmanship and b the Product when properly installed and used for its intended purpose and in its intended operating environment will perform substantially in accordance with WatchGuard applicable specifications This warranty does not apply to any Product that has been i altered repaired or modified by any party other than WatchGuard except for the replacement or inclusion of specified components authorized in and performed in strict accordance with documentation provided by WatchGuard or ii damaged or destroyed by force majeure events accidents power spikes or similar events or by any intentional reckless or negligent acts or omissions of any party You may have additional warranties with respect to the Product from the manufacturers of Product components However you agree not to look to WatchGuard for and hereby release WatchGuard from any liability for performance of enforcement of or damages or other relief on account of any such warranties or any breach thereof 2 REMEDIES If any Product does not comply with the WatchGuard warranties set forth in Section 1 above WatchGuard will following the receipt of the product you claim is defective and at its option either a repair the Product or b replace the Product with a lik
8. use of the product or associated documentation to any country to which such transfer would be prohibited by the U S Export laws and regulations If any provision of this Warranty is found to be invalid or unenforceable then the remainder shall have full force and effect and the invalid provision shall be modified or partially enforced to the maximum extent permitted by law to effectuate the purpose of this Warranty This is the entire agreement between WatchGuard and you relating to the Product and supersedes any prior purchase order communications advertising or representations concerning the Product AND BY USING THE PRODUCT YOU AGREE TO THESE TERMS IF THE PRODUCT IS BEING USED BY AN ENTITY THE INDIVIDUAL INDICATING AGREEMENT TO THESE TERMS BY USING THE PRODUCT 22 REPRESENTS AND WARRANTS THAT A SUCH INDIVIDUAL IS DULY AUTHORIZED TO ACCEPT THE WARRANTY ON BEHALF OF THE ENTITY AND TO BIND THE ENTITY TO THE TERMS OF THIS WARRANTY B THE ENTITY HAS THE FULL POWER CORPORATE OR OTHERWISE TO ENTER INTO THE WARRANTY AND PERFORM ITS OBLIGATIONS UNDER THE WARRANTY AND C THE WARRANTY AND THE PERFORMANCE OF THE ENTITY S OBLIGATIONS UNDER THE WARRANTY DO NOT VIOLATE ANY THIRD PARTY AGREEMENT TO WHICH THE ENTITY IS A PARTY No change or modification of the Warranty will be valid unless it is in writing and is signed by WatchGuard All WatchGuard products are designed and tested to meet strict safety requirements These requirements include produc
9. HCP When first powered on the WatchGuard AP is configured to automatically receive an IP address from the network via DHCP After the AP device receives an IP address the WatchGuard XTM can connect to the AP device through automatic discovery Manual IP Address Configuration If you do not use DHCP on your network you must directly connect to the WatchGuard AP and assign an IP address to the device from its local Web UI To connect directly to your WatchGuard AP device you must physically connect an Ethernet cable between the AP device and a computer then connect to the Web UI on the AP device with a web browser After you have connected to the WatchGuard AP you can configure the device with an IP address to integrate with your network To configure the AP device you must have these items Computer with an Ethernet interface Web browser Internet Explorer Firefox Safari or another similar application Before You Begin The default IP address of the WatchGuard AP device is 192 168 1 1 To make sure you can connect to the WatchGuard AP device and complete the configuration procedure you must first configure your computer to use these settings P address 192 168 1 2 Subnet mask 255 255 255 0 Gateway 192 168 1 1 Connect to the WatchGuard AP 1 On your computer open a web browser and type https 192 168 1 1 inthe location bar 2 To log in to the WatchGuard AP type the default password wgwap 3 Configur
10. THEORY AND ANY OBLIGATION LIABILITY RIGHT CLAIM OR REMEDY FOR LOSS OR DAMAGE TO OR CAUSED BY OR CONTRIBUTED TO BY THE PRODUCT 4 LIMITATION AND LIABILITY WATCHGUARD S LIABILITY WHETHER ARISING IN CONTRACT INCLUDING WARRANTY TORT INCLUDING ACTIVE PASSIVE OR IMPUTED NEGLIGENCE AND STRICT LIABILITY AND FAULT OR OTHER THEORY WITH REGARD TO ANY PRODUCT WILL IN NO EVENT EXCEED THE PURCHASE PRICE PAID BY YOU FOR SUCH PRODUCT THIS SHALL BE TRUE EVEN IN THE EVENT OF THE FAILURE OF ANY AGREED REMEDY IN NO EVENT WILL WATCHGUARD BE LIABLE TO YOU OR ANY THIRD PARTY WHETHER ARISING IN CONTRACT INCLUDING WARRANTY TORT INCLUDING ACTIVE PASSIVE OR IMPUTED NEGLIGENCE AND STRICT LIABILITY AND FAULT OR OTHER THEORY FOR COST OF COVER OR FOR ANY INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING WITHOUT LIMITATION LOSS OF PROFITS BUSINESS OR DATA ARISING OUT OF OR IN CONNECTION WITH THIS WARRANTY OR THE USE OF OR INABILITY TO USE THE PRODUCT EVEN IF WATCHGUARD HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES THIS SHALL BE TRUE EVEN IN THE EVENT OF THE FAILURE OF ANY AGREED REMEDY 5 MISCELLANEOUS PROVISIONS This Warranty will be governed by the laws of the state of Washington U S A without reference to its choice of law rules The provisions of the 1980 United Nations Convention on Contracts for the International Sales of Goods as amended shall not apply You agree not to directly or indirectly transfer the Product or
11. ch must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange or Accompany it with a written offer valid for at least three years to give any third party for a charge more than your cost of physically performing source distribution a complete machine readable copy of the corresponding source code to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange or Accompany it with the information you received as to the offer to distribute corresponding source code This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer in accord with Subsection b above 34 The source code for a work means the preferred form of the work for making modifications to it For an executable work complete source code means all the source code for all modules it contains plus any associated interface definition files plus the scripts used to control compilation and installation of the executable However as a special exception the source code distributed need not include anything that is normally distributed in either source or binary form with the major components compiler kernel and so on of the operating system on which the executable runs unless that component itself accompanies the executable If distribution of executable or object cod
12. ctices Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system it is up to the author donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License 8 If the distribution and or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries so that distribution is permitted only in or among countries not thus excluded In such case this License incorporates the limitation as if written in the body of this License 9 The Free Software Foundation may publish revised and or new versions of the General Public License from time to time Such new versions will be similar in spirit to the present version but may differ in detail to address new problems or concerns Each version is given a distinguishing version number If the Program specifies a version number of this License which applies to it and any later version you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation If the Program d
13. d sends the information necessary to activate the AP device on the same WatchGuard account where the XTM device was activated Manual Activation You can activate the AP device in your WatchGuard account just as you would activate an XTM device or add on feature Go to http www watchguard com Log in with your WatchGuard account user name and password On the Support Home tab click Activate a Product the serial number of the WatchGuard AP device including hyphens Follow any remaining prompts to complete activation of your AP device Mount the WatchGuard AP Device All of the items necessary to install your WatchGuard AP device are included in the package These items include WatchGuard AP device Setup Guide Wall Ceiling Mounting Kit T rail Ceiling Mounting Kit Mounting bracket AC adapter 12V with US EU UK AU region specific adapters Our 2 13 Ceiling Wall N Mounting Kit P3 5x32 Screws P2 6x12 Screws SS amp 69 A Mounting Kit P2 6x25 P2 6x10 ge Screws Screws 9116 1 43cm 15 16 2 38cm Spacers Clips Clips Ceiling Wall Mounting Instructions 1 Position the mounting bracket on the wall or ceiling where you want to install the WatchGuard AP device Use the mounting bracket as a guide to mark the position of the WatchGuard AP device on the wall or ceiling Remove the mounting bracket and insert the large mounting screws i
14. e is made by offering access to copy from a designated place then offering equivalent access to copy the source code from the same place counts as distribution of the source code even though third parties are not compelled to copy the source along with the object code 4 You may not copy modify sublicense or distribute the Program except as expressly provided under this License Any attempt otherwise to copy modify sublicense or distribute the Program is void and will automatically terminate your rights under this License However parties who have received copies or rights from you under this License will not have their licenses terminated so long as such parties remain in full compliance 5 You are not required to accept this License since you have not signed it However nothing else grants you permission to modify or distribute the Program or its derivative works These actions are prohibited by law if you do not accept this License Therefore by modifying or distributing the Program or any work based on the Program you indicate your acceptance of this License to do so and all its terms and conditions for copying distributing or modifying the Program or works based on it 6 Each time you redistribute the Program or any work based on the Program the recipient automatically receives a license from the original licensor to copy distribute or modify the Program subject to these terms and conditions You may not impose any further
15. e or similar product provided that you will be responsible for returning the Product and for all costs of shipping and handling Repair or replacement of the Product shall not extend the Warranty Period Any Product component part or other item replaced by WatchGuard becomes the property of WatchGuard WatchGuard shall not be responsible for return of or damage to any software firmware information or data contained in stored on or integrated with any returned Products 3 DISCLAIMER AND RELEASE THE WARRANTIES OBLIGATIONS AND LIABILITIES OF WATCHGUARD AND YOUR REMEDIES SET FORTH IN PARAGRAPHS 1 AND 2 ABOVE ARE EXCLUSIVE AND IN SUBSTITUTION FOR AND YOU HEREBY WAIVE DISCLAIM AND RELEASE ANY AND ALL OTHER WARRANTIES OBLIGATIONS AND LIABILITIES OF WATCHGUARD AND ALL OTHER RIGHTS CLAIMS AND REMEDIES YOU MAY HAVE AGAINST WATCHGUARD EXPRESS OR IMPLIED 21 ARISING BY LAW OR OTHERWISE WITH RESPECT TO ANY NONCONFORMANCE OR DEFECT IN THE PRODUCT INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ANY IMPLIED WARRANTY ARISING FROM COURSE OF PERFORMANCE COURSE OF DEALING OR USAGE OF TRADE ANY WARRANTY OF NONINFRINGEMENT ANY WARRANTY OF UNINTERRUPTED OR ERROR FREE OPERATION ANY OBLIGATION LIABILITY RIGHT CLAIM OR REMEDY IN TORT WHETHER OR NOT ARISING FROM THE NEGLIGENCE WHETHER ACTIVE PASSIVE OR IMPUTED OR FAULT OF WATCHGUARD OR FROM PRODUCT LIABILITY STRICT LIABILITY OR OTHER
16. e your WatchGuard AP with an IP address and appropriate network settings so that the device is on the same network as your WatchGuard XTM device When the WatchGuard AP is assigned an IP address the WatchGuard XTM can connect to the AP device by automatic discovery Pair the AP Device with the WatchGuard XTM You must now use the WatchGuard XTM to pair the WatchGuard AP device with the XTM and add the device to the wireless network 1 Use Policy Manager or the Fireware XTM Web UI to edit the XTM device configuration 2 Select Network gt Gateway Wireless Controller 3 Enable the Gateway Wireless Controller and save the configuration to the XTM device 4 Inthe Gateway Wireless Controller on the Access Points tab click Refresh to discover the AP device 5 Select the unpaired Access Point and click Pair 6 Inthe Pairing Passphrase dialog box type the passphrase on the AP device The default passphrase is wgwap For detailed information about WatchGuard AP pairing management and configuration with your XTM device see the Wireless section of the Fireware XTM Web UI or WSM Help at http www watchquard com help documentation xtm asp 10 Hardware Specifications WatchGuard AP Specifications MCU Processor Atheros AR9344 533MHz Memory Flash 16 MB Memory RAM 128 MB 64MB x 2 Radio AP 100 Radio 1 Atheros AR9344 for switchable 2 4Ghz 5GHz AP 200 Radio 1 Atheros AR9344 for 5GHz Radio 2 Atheros AR9382 f
17. ent and configuration with your XTM device see the Wireless section of the Fireware XTM Web UI or WSM Help at http www watchguard com help documentation xtm asp Training Resources For training presentations and additional training resources go to the WatchGuard Product Training page at http Awww watchquard com training courses asp WatchGuard User Forum An interactive online user forum moderated by senior support engineers Go to the WatchGuard forum at http www watchguard com forum Knowledge Base You can view and search the knowledge base for information on specific WatchGuard product issues at http customers watchguard com WatchGuard Products and Services For more information on WatchGuard products and services visit the WatchGuard product information page at http www watchguard com products 20 Limited Hardware Warranty This Limited Hardware Warranty the Warranty applies to the enclosed hardware product not including any associated software which is licensed pursuant to a separate end user license agreement and warranty the Product BY USING THE PRODUCT YOU either an individual or a single entity AGREE TO THE TERMS HEREOF If you do not agree to these terms please return this package along with proof of purchase to the authorized dealer from which you purchased it for a full refund WatchGuard Technologies Inc WatchGuard and you agree as set forth below or on the reverse side of this card
18. er ts zu gewahrleisten Weitere Informationen finden Sie in der elektronischen Hardware Guide Die WatchGuard Produkt ist Sicherheit unter den folgenden Normen zertifiziert CAN CSA C22 2 No 60950 1 07 A1 2011 60950 1 Amd1 2nd Edition 2005 UL 60950 1 2007 R12 11 EN 60950 1 2006 A11 A1 A12 Sicherheitshinweis Legen Sie keine Gegenst nde auf das Netzkabel Verdecken Sie nicht die L ftungs ffnungen Diese ffnungen verhindern eine berhitzung der Maschine Stecken Sie niemals Gegenstande jeglicher Art in die Schlitze oder Offnungen des Ger ts stecken Der Kontakt mit einem spannungsf hrenden Punkt oder das KurzschlieBen eines Bauteils kann zu einem Brand oder elektrischen Schlag f hren Beim Entfernen oder Installieren eines Ger tes nach den allgemeinen Installation Sicherheitshinweise AVISO DE SEGURIDAD Todos los productos WatchGuard est n dise ados y probados para satisfacer estrictos requisitos de seguridad Estos requisitos incluyen la homologaci n de productos de seguridad y otras normas de cumplimiento global Por favor lea atentamente las siguientes instrucciones antes de utilizar el producto y se refieren a ellos como sea necesario para garantizar el funcionamiento seguro y continuo de su producto Informaci n adicional se puede encontrar en la Gu a del usuario electr nica Certificaci n de seguridad del producto El producto tiene certificaci n de seguridad WatchGuard bajo las siguient
19. es normas CAN CSA C22 2 N0 60950 1 07 A1 2011 60950 1 Amd1 2nd Edition 2005 UL 60950 1 2007 R12 11 24 60950 1 2006 A11 A1 A12 Advertencia de seguridad coloque objetos sobre el cable de alimentaci n Noobstruya las aberturas de ventilaci n Estas aberturas evitan el sobrecalentamiento de la m quina Nunca introduzca objetos de ningun tipo en las ranuras o aberturas del equipo El contacto con puntos de voltaje o el cortocircuito de una pieza podr a provocar un incendio o una descarga el ctrica Al extraer o instalar un electrodom stico siga las instrucciones generales de instalaci n de seguridad FCC Certification This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This device has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a par
20. ews 2 Press the device into the ceiling T rail until the clips snap securely into place Kensington Security Slot To protect your device from theft use the Kensington security slot to attach a cable lock not included Connect the WatchGuard AP Device To connect the WatchGuard AP device 1 Insert an Ethernet cable into the Ethernet interface on the WatchGuard AP device 2 Connect the other end of the Ethernet cable to your network If you must connect to the local Web UI of the AP device connect the Ethernet network cable directly to the computer you will use to configure the AP device Ethernet DC Power Interface Connector 8 IN niii WA Bhhhh h 3 Connect the power adapter to the DC power connector on the WatchGuard AP device For more information see AC Power Adapter on page 16 If you use a PoE adapter make sure that the Ethernet cable is connected to the correct port on the PoE adapter For more information see Connect the Ethernet Power Injector on page 18 The device will power on The Power Status light flashes amber while the device boots up and then changes to steady green when the device is ready Assign an IP Address to the WatchGuard AP There are two ways you can assign an IP address to the WatchGuard AP to connect the device to your network Automatic IP address configuration by DHCP default Manual IP address configuration Automatic IP Address Configuration by D
21. f the R amp TTE Directive 1999 5 EC RoHS Statement The member states of the European Union approved directive 2002 95 EC Restrictions of Hazardous Substances RoHS directive that became valid on July 1 2006 It states that all new electrical and electronic equipment put on the market within the member states must not contain certain hazardous materials This device complies with the European Union s ROHS directive 2002 95 EC and similar regulations that may be adopted by other countries for European Sales WEEE Statement WEEE is a general set of requirements dictated in the EU Directive 2002 96 EC This Directive mandated that member EU countries enact regulations governing the Waste of Electrical and Electronic Equipment WEEE The Directive and its individual transpositions into specific country laws and legislation is aimed at the reduction of WEEE through reuse recovery and recycling of WEEE WatchGuard is working in partnership with our European Union EU distribution partners to ensure that our products are in compliance with the WEEE statutes and that the recovery of our product per the specific EU country legislative requirements is seamless for our product s end users If you have a WatchGuard product that is at its end of life and needs to be disposed of please contact WatchGuard Customer Care Department at U S Customers 877 232 3531 International Customers 1 206 613 0456 WatchGuard is reasonably confident t
22. gion specific disk plug to the AC power adapter 1 Insert the round disk plug in the AC power adapter at an angle to align with the slots 2 Rotate the disk clockwise until it clicks into position To remove a disk plug from the AC power adapter 1 Press the Push button on the round disk plug 2 Rotate the disk counter clockwise and pull it away from the adapter 16 Ethernet Power Injector You can also power the WatchGuard AP device with an optional Ethernet Power Injector This Power over Ethernet PoE device allows you to power the WatchGuard AP through an existing ethernet connection With this feature you do not have to position your WatchGuard AP device near a power outlet The Ethernet Power Injector provides 56V 15 4W power over a single 10 100 Ethernet port and also includes region specific plugs US EU UK AU for connection to a wall outlet This device complies with the IEEE 802 3af PoE specification Do not use any PoE adapters that are not IEEE 802 3af compliant as they may damage your device This device is to be connected only to PoE networks without routing to the outside plant 17 Connect the Ethernet Power Injector To connect an Ethernet Power Injector to the WatchGuard AP device 1 Attach a region specific plug to the Ethernet Power Injector 2 Plug the Ethernet Power Injector into an AC power source 3 Connect a straight through Ethernet cable from your network backbone for examp
23. hat our products do not contain any substances or hazardous materials presently banned by any legislation and do not present a risk due to hazardous materials WEEE recovery professionals should also note that these products do not have any materials that are of particular high value in their individual form 27 REACH Certificate of Compliance The new EU chemicals policy REACH Registration Evaluation Authorization and restriction of Chemicals came into effect on June 1 2007 REACH is Europe s new chemicals legislation which is applicable in all 27 EU Member States as well as the EFTA European Economic Area EEA REACH creates a new system for gathering information assessing risks to human health and the environment and authorizing or restricting the marketing and use of chemicals produced or supplied in the EEA REACH has an impact on EEA producers and importers of finished products and users of chemicals in the course of industrial or professional activities WatchGuard supports the overall REACH objective of improving the protection of human health and the environment and will meet all applicable REACH requirements WatchGuard is strongly committed to working with our customers and supply chain to define and implement the REACH requirements and ensure a smooth transition to compliance One of the REACH requirements is that manufacturers and importers have the duty to register substances they are producing or importing In accordance wi
24. he Daten 802 11a b g n 2 4Ghz amp 5GHz Intended Purpose Verwendungszweck Indoor Access Point Equipment Class Betriebsmittel der Klasse Class ll The above device complies with the essential requirements and other relevant provisions to Directive 1999 5 EC when used for its intended purpose This equipment may be operated in the USA Canada Europe Union amp Australia New Zealand Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Restrictions Italy For private use a general authorization is required if this device is used outside own premises Norway This device does not apply for the geographical area within a radius of 20 km from the center of Ny Alesund Die oben genannten Ger t entspricht den grundlegenden Anforderungen und anderen relevanten Bestimmungen der Richtlinie 1999 5 EG wenn f r den vorgesehenen Zweck verwendet werden Dieses Ger t ist f r die Verwendung in den USA Kanada Europ ische Union amp Australia New Zealand betrieben werden Warnung Dies ist eine Einrichtung der Klasse A Diese Einrichtung kann im Wohnbereich Funkst rungen verursachen In diesem Fall kann vom Betreiber verlangt werden angemessene Ma nahmen durchzuf hren Beschr nkungen Italien F r den privaten Gebrauch ist eine allgemeine Genehmigung erforderlich wenn das Ger t au erhalb der eigenen R umlichkei
25. le a router switch or hub to the IN connector on the Ethernet Power Injector 4 Connecta straight through Ethernet cable from the WatchGuard AP device Ethernet interface to the OUT connector on the Ethernet Power Injector Ethernet Power Injector Specifications Ethernet Power Injector WatchGuard Part WG003000 Specification IEEE 802 3af AC Input Voltage Rating 100 to 240VAC Output Voltage 56V Output Power 15 4W Ethernet Interfaces In RJ 45 for 10 100 Mbps Out RJ 45 for 10 100 Mbps and 56V DC Voltage on pins 4 5 and 7 8 Region specific US EU UK AU Adapter Plugs 18 Ethernet Power Injector Indicator Green Valid IEEE802 3af load detected and connected Flashing Green Red Invalid load connected Red Fault detected Temperature Operating 0 to 40 C Storage 25 to 65 C Humidity Operation 5 to 90 Dimensions L 80mm 3 15in W 45mm 1 77in H 33mm 1 29in Weight 95g 3 350z 19 Documentation and Resources For additional information about the WatchGuard AP and other WatchGuard products see these online resources Product Documentation WatchGuard AP You can view and download the most current documentation for the WatchGuard AP on the WatchGuard AP Product Documentation page at http www watchguard com help documentation ap asp WatchGuard XTM The WatchGuard AP is managed by a WatchGuard XTM device For detailed information about WatchGuard AP pairing managem
26. mage your device Reset Button To reset the WatchGuard AP device to factory default settings disconnect the power from the device Press and hold the Reset button while you reconnect power to the device Continue to hold the Reset button for at least ten seconds while the device initializes When the device completes its initialization it will be reset to factory default settings f you reset the WatchGuard AP to factory settings you must perform the pairing procedure again to pair the AP device with the XTM device 13 Device Indicators Wireless Ethernet PowerlStatus Indicator Power Status Wireless Ethernet Indicator color Not lit Amber Green Not lit Amber Amber flashing Green Green flashing Red Red flashing Not lit Amber Amber flashing Green Green flashing Interface Status No power Device booting Power on and ready Wireless off or disabled 2 4GHz and 5GHz wireless network active Transmitting and receiving data 5GHz wireless network active Transmitting and receiving data 2 4GHz wireless network active Transmitting and receiving data No link or disabled Link speed at 10 100Mbps Transmitting and receiving data Link speed at 1000Mpbs Gigabit Transmitting and receiving data 15 AC Power Adapter The included AC power adapter supplies 12V DC power to the WatchGuard AP and includes US EU UK and AU region specific adapter disk plugs To connect a re
27. n change the software or use pieces of it in new free programs and that you know you can do these things To protect your rights we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights These restrictions translate to certain responsibilities for you if you distribute copies of the software or if you modify it For example if you distribute copies of such a program whether gratis or for a fee you must give the recipients all the rights that you have You must make sure that they too receive or can get the source code And you must show them these terms so they know their rights We protect your rights with two steps 1 copyright the software and 2 offer you this license which gives you legal permission to copy distribute and or modify the software 32 Also for each author s protection and ours we want to make certain that everyone understands that there is no warranty for this free software If the software is modified by someone else and passed on we want its recipients to know that what they have is not the original so that any problems introduced by others will not reflect on the original authors reputations Finally any free program is threatened constantly by software patents We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses in effect making the program proprietary To prevent this we have made it clear that
28. nto the marks you made on the ceiling or wall Insert the long 5x32 screws through the bracket and into the mounting screws Insert the short 6x12 screws partway into the bottom of the device Do not tighten the screws completely Keep the heads of the screws exposed to attach the device to the mounting bracket If extra space is required between the device and the mounting bracket use the spacers and long 6x25 screws from the T rail mounting hardware kit To attach the device to the mounting bracket insert the screw heads from the device into the slots in the mounting bracket and rotate the device clockwise to lock the device in place Ceiling or Wall 1 Mounting Screws x Mounting Bracket S P3 5x32 Screws it Rotate device to lock in place T rail Mounting Instructions To mount your WatchGuard AP device on a suspended ceiling you can use one of the two connectors included in the mounting hardware kit 15 16in 2 38 and 9 16in 1 43cm Before you mount your WatchGuard AP device make sure you select the correct T rail connector size If you require additional space between the device and the ceiling you can use the provided spacers and long 6x25 screws To mount the device on a suspended ceiling with the T rail connectors 1 Attach the T rail connectors to the bottom of the WatchGuard AP device with the short 6x10 screws P2 6x25 6 Screws 2 6 10 Scr
29. nty keep intact all the notices that refer to this License and to the absence of any warranty and give any other recipients of the Program a copy of this License along with the Program You may charge a fee for the physical act of transferring a copy and you may at your option offer warranty protection in exchange for a fee You may modify your copy or copies of the Program or any portion of it thus forming a work based on the Program and copy and distribute such modifications or work under the terms of Section 1 above provided that you also meet all of these conditions You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change 33 You must cause any work that you distribute or publish that in whole or in part contains or is derived from the Program or any part thereof to be licensed as a whole at no charge to all third parties under the terms of this License fthe modified program normally reads commands interactively when run you must cause it when started running for such interactive use in the most ordinary way to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty or else saying that you provide a warranty and that users may redistribute the program under these conditions and telling the user how to view a copy of this License Exception if the Program itself is interactive but does not normally
30. oes not specify a version number of this License you may choose any version ever published by the Free Software Foundation 10 If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different write to the author to ask for permission For software which is copyrighted by the Free Software Foundation write to the Free Software Foundation we sometimes make exceptions for this Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally NO WARRANTY 1 BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE THERE IS NO WARRANTY FOR THE PROGRAM TO THE EXTENT PERMITTED BY APPLICABLE LAW EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND OR OTHER PARTIES PROVIDE THE PROGRAM AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESSED OR IMPLIED INCLUDING BUT NOT 36 LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU SHOULD THE PROGRAM PROVE DEFECTIVE YOU ASSUME THE COST OF ALL NECESSARY SERVICING REPAIR OR CORRECTION 2 INNO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER OR ANY OTHER PARTY WHO MAY MODIFY AND OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE BE LIABLE TO YOU FOR DAMAGES INCLUDING ANY GENERAL
31. or 2 4GHz Gigabit Physical Atheros AR8035 Layer PHY Radio Type and 2 4GHz 802 11b g n 5GHz 802 11a n Frequency Band AP 100 300 Mbps data rate AP 200 600 Mbps data rate 300 Mbps per radio Antenna Modular High Efficiency PIFA Antenna Peak Gain 2 4 to 2 5GHz 3dBi 5 150 5 875GHz AdBi Ethernet Interface 1 RJ45 connector for 10 100 1000 Gigabit Ethernet Power Interface DC jack 12V DC input Power Supply 12V 1 25A 11 Environmental Requirements To safely install your WatchGuard AP device we recommend that you Install the device indoors sure the device has adequate clearance for air flow and cooling Connect the device to a surge protected power supply to prevent damage from sudden power changes Operating temperature 32 to 104 F 0 to 40 C Operating relative humidity 596 to 9096 Non condensing Storage temperature 40 to 158 F 40 to 70 C Non operating relative humidity 5 to 90 Non condensing 12 Device Connections and Buttons Ethernet Network Interface Standard RJ45 connector that supports link speeds of 10 100 1000 Mbps Power Input A 12V AC adapter is included with your device Connect the AC adapter to the device and to a power source Use only the supplied AC power adapter If you use the optional PoE adapter make sure that the PoE adapter complies with the IEEE 802 3af PoE specification Do not use any PoE adapters that are not IEEE 802 3af compliant as they may da
32. print such an announcement your work based on the Program is not required to print an announcement These requirements apply to the modified work as a whole If identifiable sections of that work are not derived from the Program and can be reasonably considered independent and separate works in themselves then this License and its terms do not apply to those sections when you distribute them as separate works But when you distribute the same sections as part of a whole which is a work based on the Program the distribution of the whole must be on the terms of this License whose permissions for other licensees extend to the entire whole and thus to each and every part regardless of who wrote it Thus it is not the intent of this section to claim rights or contest your rights to work written entirely by you rather the intent is to exercise the right to control the distribution of derivative or collective works based on the Program In addition mere aggregation of another work not based on the Program with the Program or with a work based on the Program on a volume of a storage or distribution medium does not bring the other work under the scope of this License 3 You may copy and distribute the Program or a work based on it under Section 2 in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following Accompany it with the complete corresponding machine readable source code whi
33. restrictions on the recipients exercise of the rights granted herein You are not responsible for enforcing compliance by third parties to this License 7 If as a consequence of a court judgment or allegation of patent infringement or for any other reason not limited to patent issues conditions are imposed on you whether by court order agreement or otherwise that contradict the conditions of this License they do not excuse you from the conditions of this License If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations then as a consequence you may not distribute the Program at all For example if a patent license would not permit royalty free redistribution of the Program by all those who receive copies directly or indirectly through you then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program If any portion of this section is held invalid or unenforceable under any particular circumstance the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims this section has the sole 35 purpose of protecting the integrity of the free software distribution system which is implemented by public license pra
34. ses minimalist labeling and small LEDs coupled with wall and ceiling mounting options make these devices ideal for low profile deployment scenarios Power is provided via an AC adapter or optional PoE injector when outlet access is not easily accessible The WatchGuard AP is managed and controlled directly from a WatchGuard XTM device to provide centralized secure management and configuration of all WatchGuard wireless devices on your network The WatchGuard AP product line includes these models 100 Single radio 2 4 5Ghz switchable 2x2 MIMO 802 11n provides up to 300Mbps data rate 200 Dual radio 2 4GHz and 5GHz 2x2 MIMO 802 11n provides up to 600Mbps data rate Requirements The WatchGuard AP device must be managed by a WatchGuard XTM device that uses Fireware XTM OS v11 7 2 or higher WatchGuard AP device must be located on a Trusted or Optional network of the WatchGuard XTM device to allow communication between the two devices Registration and Activation You must register your WatchGuard AP to activate the device and start your LiveSecurity subscription The WatchGuard LiveSecurity subscription activates your hardware replacement warranty enables you to receive technical support and provides access to the latest OS updates and product news Automatic Activation After you pair a WatchGuard AP device with an XTM device the XTM device automatically connects to the WatchGuard web site an
35. stalliert und in bereinstimmung mit der Bedienungsanleitung kann es St rungen im Funkverkehr verursachen Der Betrieb dieses Ger tes in einem Wohngebiet wird wahrscheinlich sch dliche Interferenzen in dem Fall muss der Benutzer die St rungen auf seine ihre eigene Kosten zu beheben CE Notice The CE symbol on your WatchGuard Technologies equipment indicates that it is in compliance with the Electromagnetic Compatibility EMC directive and the Low Voltage Directive LVD of the European Union EU Industry Canada Certification This device complies with RSS 210 of the Industry Canada Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Ce dispositif est conforme la norme CNR 210 d Industrie Canada applicable aux appareils radio exempts de licence Son fonctionnement est sujet aux deux conditions suivantes 1 le dispositif ne doit pas produire de brouillage pr judiciable et 2 ce dispositif doit accepter tout brouillage recu y compris un brouillage susceptible de provoquer un fonctionnement ind sirable 26 R amp TTE Compliance Statement This device complies with the essential requirements of the R amp TTE Directive 1999 5 EC The following test methods have been applied in order to prove presumption of conformity with the essential requirements o
36. t safety approvals and other global compliance standards Please read the following instructions carefully before operating the product and refer to them as needed to ensure the continued safe operation of your product Additional information can be found in the electronic Hardware Guide Product Safety Certifications The WatchGuard product is safety certified under the following standards CAN CSA C22 2 N0 60950 1 07 A1 2011 60950 1 Amd1 2nd Edition 2005 UL 60950 1 2007 R12 11 EN 60950 1 2006 A11 A1 A12 Safety Warning Do not place objects on the power cord not obstruct the ventilation openings These openings prevent overheating of the machine Never push objects of any kind into slots or openings on this equipment Making a contact with a voltage point or shorting out a part may result in fire or electrical shock When removing or installing an appliance follow the general installation safety instructions Disclaimer WatchGuard shall not be held liable if the end user alters modify or repairs any WatchGuard hardware appliance 23 HINWEISE ZUR SICHERHEIT Alle WatchGuard Produkte werden entwickelt und getestet um strenge Sicherheitsanforderungen zu erf llen Diese Anforderungen umfassen Produktsicherheit Zulassungen und andere globale Compliance Standards Bitte lesen Sie die folgenden Anweisungen sorgfaltig bevor Sie das Produkt und bezeichnen sie als notwendig um den sicheren Betrieb des G
37. ten verwendet wird Norwegen Dieses Ger t darf nicht in den geografischen Gebieten innerhalb eines Radius von 20 km vom Zentrum von Ny Alesund verwendet werden AS muhka Aug Signatu Full Name Steve Zirschky Position Corporate Officer Date June 19 2012 366 4250 001 Rev A 31 GNU General Public License GPL Version 2 June 1991 Copyright 1989 1991 Free Software Foundation Inc 51 Franklin Street Fifth Floor Boston MA 02110 1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document but changing it is not allowed Preamble The licenses for most software are designed to take away your freedom to share and change it By contrast the GNU General Public License is intended to guarantee your freedom to share and change free software to make sure the software is free for all its users This General Public License applies to most of the Free Software Foundation s software and to any other program whose authors commit to using it Some other Free Software Foundation software is covered by the GNU Library General Public License instead You can apply it to your programs too When we speak of free software we are referring to freedom not price Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software and charge for this service if you wish that you receive source code or can get it if you want it that you ca
38. th the regulations the products of WatchGuard do not need to be registered for the following reasons WatchGuard does not import more than 1 metric ton per year of a substance as defined by REACH WatchGuard products are non chemical products that are not designed to release any substance under normal and reasonably predictable application Our products do not contain the listed substances at more than 0 1 by weight of the whole product part Brazil Este equipamento opera em car ter secund rio isto nao tem direito a protec o contra interfer ncia prejudicial mesmo de esta es do mesmo tipo e nao pode causar interfer ncia a sistemas operando em car ter prim rio 28 China 12 14
39. ticular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment Operations in the 5 15 5 25GHz band are restricted to indoor usage only 25 IMPORTANT NOTE FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator amp your body Dieses Ger t wurde getestet und entspricht den Grenzwerten f r ein Digitalgerat der Klasse A gemaB Teil 15 der Federal Communications Commission FCC Regeln einhalten Diese Grenzwerte sollen einen angemessenen Schutz vor sch dlichen St rungen wenn das Ger t in einer kommerziellen Umgebung betrieben wird Dieses Ger t erzeugt verwendet und kann Hochfrequenzenergie abstrahlen und wenn nicht in
Download Pdf Manuals
Related Search