Lancom Systems L-320agn
Contents
1. IP redirect High availability redundancy Fixed redirection of any packet received over the WLAN interface to a dedicated target address VRRP VRRP Virtual Router Redundancy Protocol for backup in case of failure of a device or remote station Enables passive standby groups or reciprocal backup between multiple active devices including load balancing and user definable backup priorities FirmSafe For completely safe software upgrades thanks to two stored firmware versions incl test mode for firmware updates Analog GSM modem backup Optional operation of an analog or GSM modem at the serial interface Line monitoring Routing functions Router Line monitoring with LCP echo monitoring up to 4 addresses for end to end monitoring with ICMP polling IP and NetBIOS IP multi protocol router Advanced Routing and Forwarding Separate processing of 16 contexts due to virtualization of the routers Mapping to VLANs and complete independent management and configuration of IP networks in the device i e individual settings for DHCP DNS Firewalling QoS VLAN Routing etc Automatic learning of routing tags for ARF contexts from the routing table e HTTP HTTP and HTTPS server for configuration by web interface DNS DNS client DNS server DNS relay DNS proxy and dynamic DNS client DHCP DHCP client DHCP relay and DHCP server with autodetection Cluster of several LANCOM DHCP servers per contex2. interval can be specified in either milliseconds seconds minutes hours or days Client detection Rogue WLAN client detection based on probe requests LANCOM L 320agn Wireless WLAN 802 1X supplicant Authentication of an access point in WLA Layer 3 Tunneling Features as of LCOS 8 82 gt REL D client mode at another access point via 802 1X EAP TLS EAP TTLS and PEAP Layer 3 Tunneling in conformity with the CAPWAP standard allows the bridging of WLANs per SSID to a separate IP subnet Layer 2 packets are encapsulated in Layer 3 tunnels and transported to a LANCOM WLAN controller By doing this the access point is independent of the present infrastructure of the network Possible applications are roaming without changing the IP address and compounding SSIDs without using VLANs IEEE 802 11u Note LANCOM Spectral Scan RF spectrum scan The WLAN standard IEEE 802 11u Hotspot 2 0 allows for a seamless transition from the cellular network into WLAN hotspots Authentication methods using SIM card information certificates or username and password enable an automatic encrypted login to WLAN hotspots without the need to manually enter login credentials The effective distances and transmission rates that can be achieved are depending of the site RF conditions Up to 13 channels 2 4 GHz or up to 26 channels 5 GHz depending on national regulations and manual configuration Signal strength of
3. it the server manages its own virtual COM port via Telnet RFC 2217 for remote maintenance works with popular virtual COM port drivers compliant with RFC 2217 Switchable newline conversion and alternative binary mode TCP keepalive according to RFC 1122 with configurable keepalive interval retransmission timeout and retries COM port forwarding LAN protocols eG ARP proxy ARP BOOTP DHCP DNS HTTP HTTPS IP ICMP NTP SNTP NetBIOS PPPoE server RADIUS RIP 1 RIP 2 RTP SIP SNMP TCP TFTP UDP VRRP VLAN Rapid Spanning Tree 802 1d Spanning Tree and 802 1w Rapid Spanning Tree support for dynamic path selection with redundant layer 2 connections IPv6 NDP stateless address autoconfiguration SLAAC stateful address autoconfiguration with DHCPv6 router advertisements ICMPv6 DHCPv6 DNS HTTP HTTPS PPPoE TCP UDP IPv6 Dual Stack IPv4 IPv6 dual stack IPv6 compatible LCOS applications WEBconfig HTTP HTTPS SSH Telnet DNS TFTP Firewall WAN protocols PPPoE Multi PPPoE ML PPP PPTP PAC or PNS and IPoE with or without DHCP RIP 1 RIP 2 VLAN IP IPv6 IPv6 over PPP IPv6 and IPv4 IPv6 dual stack session IPoE autoconfiguration DHCPv6 or static Tunneling protocols IPv4 IPv6 6to4 6in4 6rd static and via DHCP WAN operating mode XDSL ext modem ADSL1 ADSL2 or ADSL2 with external ADSL2 modem Interfaces LAN 10 100 1000 Base TX autosensing auto node hub PoE compliant wi
4. multiple antennas at both the transmitter and receiver to transmit multiple spatial streams The multiple transmit streams which take different routes in reflecting environments are combined at the receiver using MIMO techniques The end result is a two fold increase in throughput and improved wireless coverage due to lesser deadspots More security LANCOM sets the standards in WLAN security A comprehensive range of security technologies is supported in wireless LAN including IEEE 802 11i 802 1X WPA WPA2 WEP64 128 152 access control lists or LEPS LANCOM Enhanced Passphrase Security which enables the configuration of an optimized solution whatever the individual requirements For example Multi SSID allows the definition of up to 8 user groups each with its own level of security More management LANCOM s WLAN management tools offer real benefits to network administrators for the installation control and monitoring of access points LANCOM WLAN Controller has built in support for the L 3xx access point LANCOM s Smart Controller architecture is specifically designed to support high bandwidth applications by providing flexible data plane switching options As a result higher bandwidth applications can directly offloaded at the access point and reduces the overall cost involved in expensive network upgrades required in centralized architectures WLANmonitor visualizes the devices connected to WLAN irrespective of physical location and facil
5. L 320agn Wireless s 5 5 z 3 3 LANCOM L 320agn Wireless Single Radio Access Point for a reliable Wireless LAN coverage High Speed Wireless LAN with up to 300 Mbps gross data rate Integrated MIMO antenna for a highly discreet Wireless LAN installation Gigabit Ethernet slot Comfortable hotspot solution via Public Spot Option Separation of user groups by Muliti SSID and VLAN Available in two different designs classic and white LANCOM Systems The LANCOM L 320agn Wireless is a 802 11n dual band access point with an integrated MIMO antenna which operates either in the 2 4 or 5 GHz band As this access point features 802 3af Power over Ethernet it can even be installed if no wall sockets are available It is ideally suited for places where external antennas should be avoided to prevent theft for example in locations such as hospitals schools or hotels The LANCOM L 320agn Wireless is available in classic and white so that you can choose the design which fits best to your environment More performance The 802 11n standard includes several mechanisms such as MIMO 40 MHz channels packet aggregation and block acknowledgement which significantly increase the amount of bandwidth available for user applications With throughput rates up to 300 Mbps this represents a greater than five fold increase over the performance of 802 11a g networks Better and reliable coverage MIMO technology uses
6. Under ideal RF conditions this increases the throughput by upto 10 Infrastructure mode autonomous operation or managed by LANCOM WLAN Controller LAN bridge LAN router Point to multipoint connection of up to 16 Ethernet LANs mixed operation optional broken link detection blind mode supports VLAN When configuring Pt to Pt links pre configured names can be used as an alternative to MAC Adresses for creating a link Rapid spanning tree protocol to support redundant routes in Ethernet networks Use of the LAN connector for simultaneous DSL over LAN IP router NAT Reverse NAT IP masquerading DHCP server DHCP client DHCP relay server DNS server PPPoE client incl Multi PPPoE PPTP client and server NetBIOS proxy DynDNS client NTP port mapping policy based routing based on routing tags tagging based on firewall rules dynamic routing with RIPv2 VRRP WLAN client Transparent WLAN client mode for wireless Ethernet extensions e g connecting PCs or printers by Ethernet up to 64 MAC addresses Automatic selection of a WLAN profile max 8 with individual access parameters depending on signal strength or priority Spectral Scan Firewall Stateful inspection firewall Packet filter Extended port forwarding By scanning the RF spectrum intererences are identified and graphically illustrated Incoming Outgoing Traffic inspection based on connection information Trigger for firewall rules depending on backup sta
7. WLAN channels Illustration of signal strength on individual WLAN channels at a certain point of time IEEE 802 11n Features MIMO MIMO technology is a technique which uses multiple transmitters to deliver multiple data streams via different spatial channels Depending on the existing RF conditions the throughput is multiplied with MIMO technology 40 MHz Channels Two adjacent 20 MHz channels are combined to create a single 40 MHz channel Depending on the existing RF Conditions channel bonding doubles the throughput 20 40MHz Coexistence Mechanisms in the 2 4GHz Band Support of coexisting accesspoints with 20 and 40MHz channels in 2 4GHz band MAC Aggregation and Block Acknowledgement Maximal Ratio Combining MRC MAC Aggregation increase the 802 11 MAC efficiency by combining MAC data frames and sending it out with a single header The receiver acknowledges the combined MAC frame with a Block Acknowledgement Depending on existing RF conditions this technique improves throughput by up to 20 Maximal Ratio Combining MRC enables the receiver access point in combination with multiple antennas to optimally combine MIMO signals to improve the client reception at long range Short Guard Interval WLAN operating modes LAN access point The guard interval is the time between OFDM symbols in the air 802 11n gives the option for a shorter 400 nsec guard interval compared to the legacy 800 nsec guard interval
8. WPA2 Personal or 802 1X WPA2 Enterprise and hardware accelerated AES closed network WEP64 WEP128 WEP152 user authentication 802 1x EAP LEPS WPA1 TKIP EAP Types EAP TLS EAP TTLS MSCHAPv2 PEAPvO EAP MSCHAPv2 PEAPv1 EAP GTC EAP SIM EAP AKA EAP AKA Prime EAP FAST RADIUS server EAP server Integrated RADIUS server for MAC address list management Integrated EAP server for authentication of 802 1X clients via EAP TLS EAP TTLS PEAP MSCHAP or MSCHAPv2 Quality of Service Prioritization according to Wireless Multimedia Extensions WME subset of IEEE 802 11e U APSD WMM Power Save Extension of power saving according to IEEE 802 11e by Unscheduled Automatic Power Save Delivery equivalent to WMM Power Save U APSD supports the automatic switch of clients to a doze mode Increasmed battery lifetime for telephone calls over VOWLAN Voice over WLAN Bandwidth limitation Maximum transmit and receive rates and an individual VLAN ID can be assigned to each WLAN client MAC address Broken link detection If the link of a chosen LAN interface breaks down a WLAN module can be deactivated to let the associated clients search for a new base station Background scanning Detection of rogue AP s and the channel information for all WLAN channels during normal AP operation The Background Scan Time Interval defines the time slots in which an AP or Router searches for a foreign WLAN network in its vicinity The time
9. and TRACE options PING and TRACEROUTE for checking connections LANmonitor status display internal logging buffer for SYSLOG and firewall events Supported by all LANCOM WLAN Controller separate optional hardware equipment for installation optimization operating and monitoring of WLAN networks except for P2P connections Hardware Power supply Statistics Extensive Ethernet IP and DNS statistics SYSLOG error counter Accounting Connection time online time transfer volumes per station Snapshot function for regular read out of values at the end of a billing period Timed CRON command to reset all counters at once Export Accounting information exportable via LANmonitor and SYSLOG 12 V DC external power adapter 230 V with bayonet cap to protect against accidentally unplugging Power supply Via Power over Ethernet compliant with IEEE 802 3af LAN COM L 320agn Wireless Features as of LCOS 8 82 gt REL D Hardware Temperature range 0 45 C humidity 0 95 non condensing Housing Robust synthetic housing rear connectors ready for wall mounting Kensington lock 210 x 45 x 140 mm W x H x D Power consumption max approx 7 25 Watts with 12 V 1 A power supply adapter total power consumption of access point and power supply adapter approx 9 85 Watts via PoE Declarations of conformity EN 60950 1 EN 301 489 1 EN 301 489 17 Wi Fi Alliance Certification 802 1 1a b g
10. dBi H plane AVG Gain dBi LAN CoO M L 3 20ag n Wi reless Features as of LCOS 8 82 gt REL D Antenna Gain 2 4 GHz antenna pattern front side 2400 MHz V polarization H V 15 2 4 GHz antenna pattern right side 2400 MHz H polarization V polarization H V 154 150 15 210 LAN CoO M L 3 20ag n Wi reless Features as of LCOS 8 82 gt REL D Antenna Gain 2 45 GHz antenna pattern front side 2450 MHz H polarization V polarization H V 2 45 GHz antenna pattern right side 2450 MHz H polarization V polarization H V LAN CoO M L 3 20ag n Wi reless Features as of LCOS 8 82 gt REL D Antenna Gain 5 1 GHz antenna pattern front side 5100 MHz H polarization V polarization H V 5 1 GHz antenna pattern right side 5100 MHz H polarization V polarization H V LANCOM L 320agn Wireless Antenna Gain 5 7 GHz antenna pattern front side Features as of LCOS 8 82 gt REL D 5700 MHz H polarization H V V polarization 5 7 GHz antenna pattern front side 5 5700 MHz H polarization H V V polarization www lancom eu LANCOM Systems GmbH Adenauerstr 20 B2 52146 Wu
11. erselen Germany E Mail info lancom eu Internet www lancom eu LANCOM Systems LANCOM LANCOM Systems and LCOS are registered trademarks All other names or descriptions used may be trademarks or registered trademarks of their owners Subject to change without notice No liability for technical errors and or omissions 9 2013
12. g on the myLANCOM download server myLANCOM account mandatory Updates can be applied directly after the download or at a later time IVETE WEBconfig Integrated web server for the configuration of LANCOM devices via Internet browsers with HTTPS or HTTP Similar to LANconfig with a system overview syslog and events display symbols in the menu tree quick access with side tabs WEBconfig also features Wizards for basic configuration security Internet access LAN LAN coupling Online help for parameters in LCOS menu tree LANCOM L 320agn Wireless Management Features as of LCOS 8 82 gt REL D LANCOM Layer 2 Management emergency management The LANCOM Layer 2 Management protocol LL2M enables an encrypted access between the command line interfaces of two LANCOM device directly via a Layer 2 connection Alternative boot configuration Device Syslog During rollout devices can be preset with project or customer specific settings Up to two boot and reset persistent memory spaces can store customized configurations for customer specific standard settings memory space 1 or as a rollout configuration memory space 2 A further option is the storage of a persistent standard certificate for the authentication of connections during rollouts Syslog buffer in the RAM size depending on device memory to store events for diagnosis Default set of rules for the event protocol in Syslog The rules can be modified by
13. id TACACS to relieve TACACS servers Redundancy by setting several alternative TACACS servers Configurable option to fall back to local user accounts in case of connection drops to the TACACS servers Compatibility mode to support several free TACACS implementations Remote maintenance of 3rd party devices TFTP amp HTTP S client A remote configuration for devices behind der LANCOM can be accomplished after authentication via tunneling of arbitrary TCP based protocols e g for HTTP S remote maintenance of VoIP phones or printers of the LAN Additionally SSH and Telnet client allow to access other devices from a LANCOM device with an interface to the target subnet if the LANCOM device can be reached at its command line interface For downloading firmware and configuration files from a TFTP HTTP or HTTPS server with variable file names wildcards for name MAC IP address serial number e g for roll out management Commands for live Telnet session scripts or CRON jobs HTTPS Client authentication possible by username and password or by certificate SSH amp Telnet client SSH client function compatible to Open SSH under Linux and Unix operating systems for accessing third party components from a LANCOM router Also usable when working with SSH to login to the LANCOM device Support for certificate and password based authentication Generates its own key with sshkeygen SSH client functions are restricted to administrators with appr
14. it PMTU adjustment Layer 2 Layer 3 tagging Security Intrusion Prevention IP spoofing Automatic or fixed translation of layer 2 priority information IEEE 802 11p marked Ethernet frames to layer 3 DiffServ attributes in routing mode Translation from layer 3 to layer 2 with automatic recognition of 802 11p support in the destination device Monitoring and blocking of login attempts and port scans Source IP address check on all interfaces only IP addresses belonging to the defined IP networks are allowed Access control lists Filtering of IP or MAC addresses and preset protocols for configuration access Denial of Service protection Hcc General Protection from fragmentation errors and SYN flooding Detailed settings for handling reassembly PING stealth mode and AUTH port URL blocker Filtering of unwanted URLs based on DNS hitlists and wildcard filters Password protection Password protected configuration access can be set for each interface Alerts Authentication mechanisms Alerts via e mail SNMP Traps and SYSLOG EAP TLS EAP TTLS PEAP MS CHAP MS CHAPv2 as EAP authentication mechanisms PAP CHAP MS CHAP and MS CHAPv2 as PPP authentication mechanisms WLAN protocol filters Limitation of the allowed transfer protocols source and target addresses on the WLAN interface Adjustable reset button Adjustable reset button for ignore boot only and reset or boot
15. itates the central surveillance of the entire wireless network More reliability for the future From the very start LANCOM products are designed for a product life of several years They are equipped with hardware dimensioned for the future Even reaching back to older product generations updates to the LANCOM Operating System LCOS are available several times a year free of charge and offering major features LANCOM offers unbeatable protection of your investment LANCOM L 320agn Wireless Frequency band 2 4 GHz or 5 GHz Features as of LCOS 8 82 gt REL D 2400 2483 5 MHz ISM or 5150 5825 MHz depending on country specific restrictions Integrated Antenna Gain up to 3 dBi in 2 4 GHz up to 4 5 dBi in 5 GHz Data rates 802 11b g 54 Mbps to IEEE 802 11g fallback to 48 36 24 18 12 9 6 Mbps Automatic Rate Selection compatible to IEEE 802 11b 11 5 5 2 1 Mbps Automatic Rate Selection 802 11 b g compatibility mode or pure g or pure b Data rates 802 11a h 54 Mbps fallback to 48 36 24 18 12 9 6 Mbps Automatic Rate Selection fully compatible with TPC adjustable power output and DFS automatic channel selection radar detection according to EN 301 893 Data rates 802 11n 300 Mbps according to IEEE 802 11n with MSC15 Fallback to 6 5 Mbps with MSCO Range 802 1 1a b g Up to 150 m up to 30 m in buildings Range 802 11n Up to 250 m 6 5 Mbps up to 20 m 300 Mb
16. ith matching properties LANmonitor Monitoring application for Microsoft Windows for remote surveillance and logging of the status of LANCOM devices and connections incl PING diagnosis and TRACE with filters and save to file Search function within TRACE tasks Wizards for standard diagnostics Export of diagnostic files for support purposes including bootlog sysinfo and device configuration without passwords Graphic display of key values marked with an icon in LANmonitor view over time as well as table for minimum maximum and average in a separate window e g for Rx Tx CPU load free memory Monitoring of the LANCOM managed switches Flick easily through different search results by LANCOM QuickFinder WLANmonitor Monitoring application for Microsoft Windows for the visualization and monitoring of LANCOM WLAN installations incl Rogue AP and Rogue Client visualization LANCOM QuickFinder as search filter that reduces the view to devices with matching properties Firewall GUI Graphical user interface for configuring the object oriented firewall in LANconfig Tabular presentation with symbols for rapid understanding of objects choice of symbols for objects objects for actions Quality of Service remote sites services default objects for common scenarios individual object definition e g for user groups Automatic software update Voluntary automatic updates for LCMS Search online for LCOS updates for devices managed by LANconfi
17. m no 61377 UK Surge arrestor LAN cable AirLancer Extender SA LAN surge arrestor LAN cable item no 61213 LANCOM Wall Mount For simple theft proof mounting of LANCOM devices with plastic housings item no 61349 Analog modem backup serial adapter LANCOM Serial Adapter Kit item no 61500 LAN COM L 320agn Wireless Features as of LCOS 8 82 gt REL D Accessories Power over Ethernet Injector LANCOM GE PoE Power Injector item no 61554 EU and 61555 UK Power over Ethernet Swi LANCOM ES 1108P 8 port Fast Ethernet switch with 4 PoE ports item no 61450 EU and 61449 UK Power over Ethernet Swi LANCOM ES 2126P 24 port Fast Ethernet PoE switch 802 3af max 185 W 2 Gigabit ports 2 SFP slots item no 61468 EU Item number s LANCOM L 320agn Wire 61529 LANCOM L 320agn Wireless White EU 61564 LANCOM L 320agn Wireless UK 61530 LANCOM L 320agn Wireless White UK 61565 LANCOM L 320agn Wireless 10 piece bulk 61519 IL LANCOM L 320agn Wireless 10 piece bulk 61535 LANCOM L 320agn Wireless White EU bulk 61566 10 LANCOM L 320agn Wireless 10 piece bulk 61547 UK LANCOM L 320agn Wireless White UK bulk 61567 10 There is no 5GHz frequency support available in the IL Version Antenna Gain Overview Antenna Gain in different Frequencies Sig Frequency x GHz H plane Peak Gain dBi H plane AVG Gain dBi H plane Peak Gain
18. matic DFS dynamic channel selection depending on national regulations Seamless handover between radio cells IAPP support with optional restriction to an ARF context IEEE 802 11d support WPA2 fast roaming Pre authentication and PMK caching for fast roaming Concurrent WLAN clients Up to 30 clients per radio recommended 512 clients max Fast client roaming With background scanning moving LANCOM client mode access points pre authenticate to alternative access points which offer a better signal before Roaming fails VLAN VLAN ID definable per interface WLAN SSID point to point connection and routing context 4094 IDs IEEE 802 1q Dynamic VLAN assignment Dynamic VLAN assignment for target user groups based on MAC addresses BSSID or SSID by means of external RADIUS server Q in Q tagging Support of layered 802 1Q VLANs double tagging Multi SSID Simultaneous use of up to 8 independent WLAN networks per WLAN interface IGMP snooping Support for Internet Group Management Protocol IGMP in the WLAN bridge for WLAN SSIDs and LAN interfaces for specific switching of multicast packets devices with integrated WLAN only Automated detection of multicast groups Configurable action for multicast packets without registration Configuration of static multicast group members per VLAN ID Configuration of query simulation for multicast membership per VLAN ID Security IEEE 802 111 WPA2 with passphrase
19. n Wi Fi Certified 2 4 GHz WLAN EN 300 328 5 GHz WLAN EN 301 893 Medical Medical conformity with EN 60601 1 2 Notifications Certifications notified in Germany Belgium Netherlands Luxembourg Austria Switzerland UK Italy Spain France Portugal Czech Republic Denmark IPv6 IPv6 Ready Gold Note You will find all declarations of conformity in the products section of our website at www lancom systems eu Scope of delivery CD DVD Data medium with management software LANconfig LANmonitor WLANmonitor LANCAPI and documentation Cable 1 Ethernet cable 3 m Power supply unit External power adapter 230 V NEST 12 V 1 5 A DC S coaxial power connector 2 1 5 5 mm bayonet temperature range from 5 to 45 C LANCOM item no 110723 EU LANCOM item no 110829 UK Power supply unit External power adapter 230 V NEST 12 V 1 5 A DC S coaxial power connector 2 1 5 5 mm bayonet temperature range from 5 to 45 C LANCOM item no 110723 EU LANCOM item no 110829 UK not included in bulk delivery Support 3 years Support via Hotline and Internet KnowledgeBase Software updates Regular free updates LCOS operating system and LANCOM Management System via Internet Options LANCOM Next Business Day Service Extension CPE item no 61411 Warranty Extension LANCOM 2 Year Warranty Extension CPE item no 61414 Public Spot LANCOM Public Spot Option authentication and accounting software for hotspots incl Voucher pri
20. nting through Standard PC printer item no 60642 Accessories LANCOM Large Scale Monitor Powerful monitoring system for WLAN VPN and LAN infrastructures of mid sized to large networks upgradable for up to 1000 monitored devices for a proactive error management browser based remote monitoring intuitive user interface graphic floorplans configurable triggers for alarms and messages users roles and rights management item no 62910 LANCOM WLC 4006 EU UK US LANCOM WLAN controller for central management of 6 opt up to 30 LANCOM access points and WLAN routers item no 62035 EU item no 62036 UK and item no 62037 US LANCOM WLC 4006 EU UK LANCOM WLAN controller for central management of 6 or 12 LANCOM access points and WLAN routers item no 61367 EU and item no 61368 UK only stock devices article is no longer available LANCOM WLC 4025 EU UK US LANCOM WLAN controller for central management of 25 opt up to 100 LANCOM access points and WLAN routers item no 61378 item no Art Nr 61379 and item no 61384 US LANCOM WLC 4025 EU UK LANCOM WLAN controller for central management of 25 opt up to 100 LANCOM access points and WLAN routers item no 61550 EU and item no 61551 UK only stock devices article is no longer available LANCOM WLC 4100 EU UK LANCOM WLAN controller for central management of 100 opt up to 1000 LANCOM access points and WLAN routers item no 61369 EU and ite
21. opriate rights Telnet client function to login administer third party devices or other LANCOM devices from command line interface HTTPS Server Option to choose if an uploaded certificate or the default certificate is used by the HTTPS server Security Access rights read write over WAN or W LAN can be set up separately Telnet SSL SSH SNMP HTTPS HTTP access control list Scripting Scripting function for batch programming of all command line parameters and for transferring partial configurations irrespective of software versions and device types incl test mode for parameter changes Utilization of timed control CRON or connection establishment and termination to run scripts for automation Scripts can send e mails with various command line outputs as attachments Load commands SNMP LoadFirmware LoadConfig and LoadScript can be executed conditionally in case certain requirements are met For example the command LoadFirmware could be executed on a daily basis and check each time if the current firmware is up to date or if a new version is available In addition LoadFile allows the upload of files including certificates and secured PKCS 12 containers SNMP management via SNMPv2 new unified private MIB for all most current and future LANCOM devices with LCOS Download link in WEBconfig Timed control Diagnosis LANCOM WLAN Controller Scheduled control of parameters and actions with CRON service Extensive LOG
22. ps indoor Output power at radio module 2 4 GHz 802 11b 14dBm 1 2 5 5 and 11 Mbps 802 11g 17dBm 6 up to 36 Mbps 16dBm 48 and 54 Mbps 802 11n 16dBm 6 5 13 Mbps MCS0 8 20 MHz 15 dBm 65 130 Mbps MCS7 15 20 MHz 15 dBm 15 30 Mbps MCS0 8 40 MHz 14 dBm 150 300 Mbps MCS7 15 40 MHz Output power at radio module 5 GHz 802 1 1a h 15 dBm 6 up to 36 Mbps 14 dBm 48 Mbps 12 dBm 54 Mbps 802 11n 15 dBm 6 5 13 Mbps MCS0 8 20 MHz 7 up to 10 dBm 65 130 Mbps MCS7 15 20 MHz 14 dBm 15 30 Mbps MCS0 8 40 MHz 6 up to 9 dBm 150 300 Mbps MCS7 15 40 MHz Minimum transmission power Transmission power reduction in software in 1 dB steps to min 0 5 dBm Receiver sensitivity 2 4 GHz 802 11b 98 dBm 1 Mbps 94 dBm 11 Mbps 802 11g 96 dBm 6 Mbps 82 dBm 54 Mbps 802 11n 95 dBm 6 5 Mbps MCSO 20 MHz 78 dBm 65 Mbps MCS 7 20 MHz 92 dBm 15 Mbps MCSO 40 MHz 75 dBm 150 Mbps MCS7 40 MHz Receiver sensitivity 5 GHz 802 1 1a h 98 dBm 6 Mbps 81 dBm 54 Mbps 802 11n 94 dBm 6 5 Mbps MCSO 20 MHz 76dBm 65 Mbps MCS 7 20 MHz 92 dBm 15 Mbps MCSO 40 MHz 72 dBm 150 Mbps MCS7 40 MHz Radio channels 2 4 GHz Up to 13 channels max 3 non overlapping depending on country specific restrictions Radio channels 5 GHz Roaming Up to 26 non overlapping channels available channels and further obligations such as auto
23. t ARF network enables caching of all DNS assignments at each router DHCP forwarding to multiple redundant DHCP servers NetBIOS NetBIOS IP proxy NTP NTP client and SNTP server automatic adjustment for daylight saving time Policy based routing Policy based routing based on routing tags Based on firewall rules certain data types are marked for specific routing e g to particular remote sites or lines Dynamic routing Dynamic routing with RIPv2 Learning and propagating routes separate settings for LAN and WAN Extended RIPv2 including HopCount Poisoned Reverse Triggered Update for LAN acc to RFC 2453 and WAN acc to RFC 2091 as well as filter options for propagation of routes Definition of RIP sources with wildcards DHCPv6 Layer 2 functions ARP lookup DHCPv6 client DHCPv6 server DHCPv6 relay stateless and stateful mode IPv6 address IA_NA prefix delegation IA_PD DHCPv6 reconfigure server and client Packets sent in response to LCOS service requests e g for Telnet SSH SNTP SMTP HTTP S SNMP etc via Ethernet can be routed directly to the requesting station default or to a target determined by ARP lookup LAN COM L 320agn Wireless Features as of LCOS 8 82 gt REL D Layer 2 functions LLDP Automatic discovery of network topology in layer 2 networks Link Layer Discover Protocol COM port server COM port server for the DIN interface For a serial device connected to
24. th IEEE 802 3af DSL over LAN DSLoL The LAN port can even parallel to LAN mode be used as a WAN port for connecting external DSL modems PPPoE or external routers Serial interface Serial configuration interface COM port 8 pin Mini DIN 9 600 115 000 baud suitable for optional connection of analog GPRS modems Supports internal COM port server and allows for transparent asynchronous transmission of serial data via TCP Internal antenna Radio module uses two internal antennas LCMS LANCOM Management System LANconfig Configuration program for Microsoft Windows incl convenient Setup Wizards Optional group configuration simultaneous remote configuration and management of multiple devices over IP connection HTTPS HTTP TFTP A tree view of the setting pages like in WEBconfig provides quick access to all settings in the configuration window Password fields which optionally display the password in plain text and can generate complex passwords Configuration program properties per project or user Automatic storage of the current configuration before firmware updates Exchange of configuration files between similar devices e g for migrating existing configurations to new LANCOM products Detection and display of the LANCOM managed switches Extensive application help for LANconfig and parameter help for device configuration LANCOM QuickFinder as search filter within LANconfig and device configurations that reduces the view to devices w
25. the administrator Display and saving of internal Syslog buffer events from LANCOM devices with LANmonitor display only with WEBconfig Access rights Individual access and function rights for up to 16 administrators Alternative access control on a per parameter basis with TACACS User administration RADIUS user administration for dial in access PPP PPTP Support for RADSEC Secure RADIUS providing secure communication with RADIUS servers Remote maintenance Remote configuration with Telnet SSL SSH with password or public key browser HTTP HTTPS TFTP or SNMP firmware upload via HTTP HTTPS or TFTP TACACS Support of TACACS protocol for authentication authorization and accounting AAA with reliable connections and encrypted payload Authentication and authorization are separated completely LANCOM access rights are converted to TACACS levels With TACACS access can be granted per parameter path command or functionality for LANconfig WEBconfig or Telnet SSH Each access and all changes of configuration are logged Access verification and logging of SNMP Get and Set requests WEBconfig supports the access rights of TACACS and choice of TACACS server at login LANconfig provides a device login with the TACACS request conveyed by the addressed device Authorization to execute scripts and each command within them by checking the TACACS server s database CRON action table and script processing can be diverted to avo
26. tus e g simplified rule sets for low bandwidth backup lines Limitation of the number of sessions per remote site ID Check based on the header information of an IP packet IP or MAC source destination addresses source destination ports DiffServ attribute remote site dependant direction dependant bandwidth dependant Network Address Translation NAT based on protocol and WAN address i e to make internal webservers accessible from WAN N N IP address mapping Actions N N IP address mapping for translation of IP addresses or entire networks The firewall marks packets with routing tags e g for policy based routing Source routing tags for the creation of independent firewall rules for different ARF contexts Forward drop reject block sender address close destination port disconnect Notification Quality of Service Traffic shaping Via e mail SYSLOG or SNMP trap Dynamic bandwidth management with IP traffic shaping LANCOM L 320agn Wireless Quality of Service Features as of LCOS 8 82 gt REL D Bandwidth reservation Dynamic reservation of minimum and maximum bandwidths totally or connection based separate settings for send and receive directions Setting relative bandwidth limits for QoS in percent DiffServ TOS Packet size control Priority queuing of packets based on DiffServ TOS fields Automatic packet size control by fragmentation or Path Maximum Transmission Un
Download Pdf Manuals
Related Search