Intel SSD 525 30GB
Contents
1. 90 December 2012 Order Number 328354 001US Intel Solid State Drive 525 Series Product Specification 15 intel Table 10 SMART Attributes Attribute Intel Solid State Drive 525 Series Status Flags SP EC ER PE oc PW Threshold BBh Uncorrectable Error Count The raw value shows the count of errors that could not be recovered using Error Correction Code ECC 0 none BEh Temperature Reports real time temperature of drive as measured by temperature sensor on drive PCB The normalized value reports the current temperature value The raw value shows current lifetime highest and lifetime lowest temperatures Byte 1 0 current temp Celsius Byte 3 2 lifetime highest temp Celsius Byte 5 4 lifetime lowest temp Celsius O none COh Power Off Retract Count Unsafe Shutdown Count The raw value of this attribute reports the cumulative number of unsafe unclean shutdown events over the life of the device An unsafe shutdown occurs whenever the device is powered off without STANDBY IMMEDIATE being the last command 0 none C7h Elh CRC Error Count The total number of encountered SATA interface cyclic redundancy check CRC errors Host Writes The raw value of this attribute reports the total number of sectors written by the host system The raw value is increased by 1 for every 65 536 sectors 32MB written by the host2. 0 none 0 none E2h Timed Workload Media Wear Measures the wear seen by the SSD since reset of the workload timer attribute E4h as a percentage of the maximum rated cycles 0 none E3h Timed Workload Host Read Write Ratio Shows the percentage of I O operations that are read operations since reset of the workload timer attribute E4h 0 none E4h Timed Workload Timer Measures the elapsed time number of minutes since starting this workload timer 0 none E8h Available Reserved Space This attribute reports the number of reserve blocks remaining The normalized value begins at 100 64h which corresponds to 100 percent availability of the reserved space The threshold value for this attribute is 10 percent availability 10 Intel Solid State Drive 525 Series Product Specification 16 December 2012 Order Number 328354 001US m Intel Solid State Drive 525 Series n tel Table 10 SMART Attributes Status Flags ID Attribute Threshold SP EC ER PE oc PW Media Wearout Indicator This attribute reports the number of cycles the NAND media has undergone The normalized value declines linearly from 100 to 1 as the average erase cycle count E9h increases from 0 to the maximum rated 1 1 0 0 1 0 0 none cycles Once the normalized value reaches 1 the number will not decrease although it is likely that significant ad
3. Canada European Union EN 55022 Information technology equipment Radio disturbance characteristics Limits and methods of measurement CISPR 22 2008 Modified EN 55022 2006 and its amendments European Union EN 60950 1 2nd Edition UL CSA 60950 1 2nd Edition Information Technology Equipment Safety Part 1 General Requirements Information Technology Equipment Safety Part 1 General Requirements USA Canada USA Canada Intel amp Solid State Drive 525 Series Product Specification 8 December 2012 Order Number 328354 001US m e Intel Solid State Drive 525 Series n tel 2 6 Reliability The Intel SSD 525 Series meets or exceeds SSD endurance and data retention requirements as specified in the JESD218 specification Reliability specifications are listed in Reliability Specifications Table 8 Reliability Specifications Parameter Value Uncorrectable Bit Error Rate UBER Uncorrectable bit error rate will not exceed one sector in the specified number of bits read In the unlikely event of a nonrecoverable read error the SSD will report it as a read failure to the host the sector in error is considered corrupt and is not returned to the host lt 1 sector per 107 bits read Mean Time Between Failures MTBF Mean Time Between Failures is estimated based on Telcordia 1 200 000 hours methodology and demonstrated through Reliability Demonstr
4. Intel Solid State Drive 525 Series Product Specification 6 December 2012 Order Number 328354 001US m e Intel Solid State Drive 525 Series n tel 2 3 Electrical Characteristics Table 5 Operating Voltage and Power Consumption Electrical Characteristics Value Operating Voltage for 3 3 V 5 Min 3 14 V Max 3 47 V Power Consumption TYP Active 300 mw Idle 250 mW Notes 1 Active power measured during execution of MobileMark 2007 with SATA Link Power Management LPM enabled 2 Idle power defined as SSD at idle with SATA Link Power Management LPM enabled 2 4 Environmental Conditions Table 6 Temperature Shock Vibration Temperature Range Module Temperature Operating 0 70 C Non operating 55 95 C Temperature Gradient Operating Non operating 30 TYP C hr 30 TYP C hr Humidity Operating 5 95 96 Non operating 5 95 96 Shock and Vibration Range Shock Operating 1 000 G Max at 0 5 msec Non operating 1 000 G Max at 0 5 msec Vibration Operating 2 17 Gams 5 700 Hz Max Non operating 3 13 Grus 5 800 Hz Max Notes 1 As measured by temperature sensor SMART Attribute BEh 2 Temperature gradient measured without condensation 3 Shock specifications assume that one side of SSD is inserted into SATA connector and the other side is secured by screw Both connector and screw are securely mounted on a fixture that is firmly att
5. 48 bit Address command set which consists of e FLUSH CACHE EXT READ DMA EXT READ NATIVE MAX ADDRESS READ NATIVE MAX ADDRESS EXT READ SECTOR S EXT READ VERIFY SECTOR S EXT SET MAX ADDRESS EXT WRITE DMA EXT WRITE MULTIPLE EXT WRITE SECTOR S EXT 5 10 General Purpose Log Command Set The Intel SSD 525 Series supports the General Purpose Log command set which consists of READ LOG EXT WRITE LOG EXT READ LOG DMA EXT WRITE LOG DMA EXT 5 11 Native Command Queuing The Intel SSD 525 Series supports the Native Command Queuing NCQ command set which includes READ FPDMA QUEUED WRITE FPDMA QUEUED Note With a maximum queue depth equal to 32 Intel amp Solid State Drive 525 Series December 2012 Product Specification Order Number 328354 001US 19 intel Intel Solid State Drive 525 Series 5 12 Software Settings Preservation The Intel SSD 525 Series supports the SET FEATURES parameter to enable disable the preservation of software settings 5 13 SATA Link Power Management LPM The Intel SSD 525 Series supports the SET FEATURES parameter to enable Device Initiated Power Management DIPM The SSD also supports Host Initiated Power Management HIPM Intel Solid State Drive 525 Series Product Specification December 2012 20 Order Number 328354 001US m e Intel Solid State Drive 525 Series n tel 6 0 Certifications and Declarations Table 13 describes the Device Certification
6. 550 550 280 280 280 280 280 SATA 3Gb s i 3 diac er MUS 275 475 500 520 520 240 245 260 260 260 SATA 3Gb s Notes 1 Random 4 KB write performance measured using out of box SSD 2 Performance measured using lometer with Queue Depth 32 Measurements are performed on 8 GB of Logical Block Address LBA range on a full SSD 3 Performance measured using lometer with Queue Depth 32 Intel amp Solid State Drive 525 Series December 2012 Product Specification Order Number 328354 001US 5 intel Table 3 Intel Solid State Drive 525 Series Incompressible Performance Intel SSD 525 Series Specification Unit 30 GB 60 GB 120 GB 180 GB 240 GB Random 4 KB Read up to IOPS 7 000 12 000 24 000 46 000 46 000 Random 4 KB Write up to IOPS 2 500 6 900 13 000 13 000 16 500 Sequential Read up to 1 MB s 200 430 550 550 550 Sequential Write up to 1 MB s 40 80 150 170 235 Notes 1 Performance measured using lometer with Queue Depth 32 Measurements are performed on 8 GB of Logica LBA range Table 4 Latency Specification Intel SSD 525 Series Block Address Latency Read Write Power On To Ready 80 us TYP 85 us TYP 2 s TYP Notes 1 Based on sequential 4 KB using lometer with Queue Depth 1 workload with compressible non random data pattern Write Cache Enabled 2 Power On To Ready time assumes proper shutdown
7. ACS 2 Specification http www t13 org June 2009 Serial ATA Revision 3 0 http www sata io org Oct 2010 JEDEC Solid State Product Outline mSATA SSD Assembly http www jedec org July 2011 Serial ATA Revision 3 1 mSATA definition http www sata io org Compliance with EN 55022 1998 Information technology equipment Radio disturbance characteristics Limits and methods of measurement CISPR 22 1997 Modified http www iec ch 8 0 Terms and Acronyms Table 15 defines the terms and acronyms used in this document Table 15 Glossary of Terms and Acronyms Term Definition ATA Advanced Technology Attachment DAS Device Activity Signal DIPM Device Initiated Power Management DMA Direct Memory Access EXT Extended FPDMA First Party Direct Memory Access Gigabyte 1 000 000 000 bytes GB Note The total usable capacity of the SSD may be less than the total physical capacity because a small portion of the capacity is used for NAND flash management and maintenance purposes HDD Hard Disk Drive Intel amp Solid State Drive 525 Series Product Specification 22 December 2012 Order Number 328354 001US Intel Solid State Drive 525 Series Table 15 Glossary of Terms and Acronyms Term Definition HIPM Host Initiated Power Management 1 0 Input Output IOPS Input Output Operations Per Second
8. Vendor Specific Manufacturing Pin P46 Reserved No Connect P47 Vendor Vendor Specific Manufacturing Pin P4g H1 5 V 1 5 V Source P49 DA DSS Device Activity Signal Disable Staggered Spin up P50 GND Return Current Path p51 Presence Detection Shall be pulled to GND by device P52 3 3V 3 3 V Source Notes 1 1 5 V rail is not used on the Intel SSD 525 Series No connect on the host side Pin 6 28 and 48 shall be unconnected on the device side to avoid conflicts with wireless coexistence pins as specified in PCI Express Mini Card Specification 2 Pins 30 and 32 are intended for use as a two wire interface to read a memory device to determine device information an example of this would be for use as SMB bus pins These pins are not designed to be active in conjunction with the SATA signal differential pairs Not used on the Intel SSD 525 Series No connect on the host side 3 Vendor specific pins are not used in the Intel SSD 525 Series No connect on the host side 4 Presence detection pin indicates presence of an mSATA device Intel amp Solid State Drive 525 Series Product Specification December 2012 12 Order Number 328354 001US m e Intel amp Solid State Drive 525 Series n tel 5 0 Supported Command Sets The Intel SSD 525 Series supports all mandatory Advanced Technology Attachment ATA and Serial ATA SATA commands defined in the ACS 2 and SATA Revision 3 0 specifications The mandatory and optional c
9. 76 F 070Eh Serial ATA capabilities 77 F 0006h Reserved for future Serial ATA definition 78 F 004Ch Serial ATA features supported 79 V 0040h Serial ATA features enabled 80 F 03FCh Major version number 81 F FFFFh Minor version number 82 F 746Bh Command set supported 83 F 7429h Command sets supported 84 F 6163h Command set feature supported extension 85 V 7469h Command set feature enabled 86 V B409h Command set feature enabled 87 V 6163h Command set feature default 88 V 207Fh Ultra DMA Modes 89 F 0002h Time required for security erase unit completion December 2012 Order Number 328354 001US Intel amp Solid State Drive 525 Series Product Specification 25 m n tel Intel Solid State Drive 525 Series Table 16 Returned Sector Data F Fixed Word V Variable Default Value Description X Both 90 F 0001h Time required for enhanced security erase completion 91 V OOFEh Current advanced power management value 92 V FFFEh Master Password Revision Code 93 F Oh Hardware reset result the contents of bits 12 0 of this word shall change only during the execution of a hardware reset 94 V Oh Vendor s recommended and actual acoustic management value 95 F Oh Stream minimum request size 96 V Oh Streaming transfer time DMA 97 V Oh Streaming access latency DMA and PIO 98 99 F Oh Streaming performance granularity 100 103 V varies Maximum user LBA for 48
10. ERASE PREPARE SECURITY ERASE UNIT SECURITY FREEZE LOCK SECURITY DISABLE PASSWORD 5 4 SMART Command Set The Intel SSD 525 Series supports the SMART command set which consists of SMART READ DATA SMART READ ATTRIBUTE THRESHOLDS SMART ENABLE DISABLE ATTRIBUTE AUTOSAVE SMART SAVE ATTRIBUTE VALUES SMART EXECUTE OFF LINE IMMEDIATE SMART READ LOG SECTOR SMART WRITE LOG SECTOR SMART ENABLE OPERATI ONS SMART DISABLE OPERATI ONS SMART RETURN STATUS Intel amp Solid State Drive 525 Series Product Specification December 2012 14 Order Number 328354 001US Intel Solid State Drive 525 Series 5 4 1 SMART Attributes ntel Table 10 lists the SMART attributes supported by the Intel SSD 525 Series Table 11 lists the corresponding status flags and threshold settings Table 10 SMART Attributes Attribute Status Flags SP EC PE oc PW Threshold 05h Re allocated Sector Count The raw value of this attribute shows the number of retired blocks since leaving the factory grown defect count 0 none 09h Power On Hours Count The raw value reports two values the first 4 bytes report the cumulative number of power on hours over the life of the device the remaining bytes report the number of milliseconds since the last hour increment The On Off status of the Device Initiated Power Management DIPM feature will affect the number of hours reported If DIPM is turn
11. KB Kilobyte 1 024 bytes LBA Logical Block Address LPM Link Power Management MB Megabyte 1 000 000 bytes MLC Multi level Cell MTBF Mean Time Between Failures NCQ Native Command Queuing NOP No Operation PIO Programmed Input Output RDT Reliability Demonstration Test RMS Root Mean Squared SATA Serial Advanced Technology Attachment SMART Self Monitoring Analysis and Reporting Technology SSD Solid State Drive TYP Typical UBER Uncorrectable Bit Error Rate 9 0 Revision History Date Revision Description December 2012 December 2012 001 Initial release Order Number 328354 001US Intel amp Solid State Drive 525 Series Product Specification 23 m n tel Intel Solid State Drive 525 Series Appendix I DENTI FY DEVI CE Command Data Table 16 details the sector data returned after issuing an IDENTIFY DEVICE command Table 16 Returned Sector Data Fixed Word V Variable Default Value Description X Both 0 F 0040h General configuration bit significant information 1 X 3FFFh Obsolete Number of logical cylinders 16 383 2 V C837h Specific configuration 3 X 0010h Obsolete Number of logical heads 16 4 5 X Oh Retired 6 X 003Fh Obsolete Number of logical sectors per logical track 63 7 8 V Oh Reserved for assignment by the CompactFlash Association CFA 9 X Oh Retired 10 19 F varies Serial number 20 ASCII charac
12. Reserved No Connect P12 Reserved No Connect P13 Reserved No Connect P14 Reserved No Connect P15 GND Return Current Path P16 Reserved No Connect P17 Reserved No Connect P18 GND Return Current Path P19 Reserved No Connect December 2012 Order Number 328354 001US Intel Solid State Drive 525 Series Product Specification 11 intel Intel Solid State Drive 525 Series Table 9 Serial ATA Power Pin Definitions Pin Function Definition P20 Reserved No Connect P21 GND Return Current Path P22 Reserved No Connect P23 B Host Receiver Differential Signal Pair This is an output of the SSD P24 T3 3V 3 3 V Source P25 B Host Receiver Differential Signal Pair This is an output of the SSD P26 GND Return Current Path P27 GND Return Current Path P28 1 5 V 1 5 V Source P29 GND Return Current Path P30 Two Wire Interface Two Wire Interface Clock P31 A Host Transmitter Differential Signal Pair This is an input of the SSD P32 Two Wire Interface Two Wire Interface Data P33 A Host Transmitter Differential Signal Pair This is an input of the SSD P34 GND Return Current Path P35 GND Return Current Path P36 Reserved No Connect P37 GND Return Current Path P38 Reserved No Connect P39 3 3V 3 3 V Source P40 GND Return Current Path P41 3 3V 3 3 V Source P42 Reserved No Connect P43 Device Type No Connect P44 Reserved No Connect P453 Vendor
13. ached on a shock table The shock stimulus is applied in X Y and Z axis respectively Shock specification is measured using peak acceleration and pulse width value 4 Vibration specifications assume that one side of SSD is inserted into SATA connector and the other side is secured by screw Both connector and screw are securely mounted on a fixture that is firmly attached on vibration table The vibration stimulus is applied in X Y and Z axis respectively Vibration specification is measured using G Root mean Squared GRMS value Intel amp Solid State Drive 525 Series Product Specification 7 December 2012 Order Number 328354 001US intel 2 5 Intel Solid State Drive 525 Series Product Regulatory Compliance The Intel SSD 525 Series meets or exceeds the regulatory or certification requirements in Product Regulatory Compliance Specifications Table 7 Product Regulatory Compliance Specifications Title Description Region for which conformity declared TITLE 47 Telecommunication CHAPTER I FEDERAL COMMUNICATIONS COMMISSION PART 15 RADIO FREQUENCY DEVICES ICES 003 Issue 4 Interference Causing Equipment Standard Digital Apparatus IEC 555024 Information Technology Equipment Immunity characteristics Limits and methods of measurement CISPR 24 2010 FCC Part 15B Class B CAN CSA CEI IEC CISPR 22 02 This is CISPR 22 1997 with Canadian modifications EN 55024 1998 and its amendments USA
14. ation Test RDT Minimum Useful Life Endurance Rating 30 GB Other Capacities Minimum useful life under typical client workloads with up to 20 GB of 3 years 5 years host writes per day Insertion Cycles 250 insertion removal cycles Maximum insertion removal cycles on mSATA power cable Intel amp Solid State Drive 525 Series December 2012 Product Specification Order Number 328354 001US 9 E I n te Intel amp Solid State Drive 525 Series 3 0 Mechanical I nformation This figure shows the physical package information for the mSATA full size Intel SSD 525 Series All dimensions are in millimeters Figure 1 Dimensions for I ntel SSD 525 Series BOTTOM SIDE 3 20 50 80 Intel amp Solid State Drive 525 Series Product Specification December 2012 10 Order Number 328354 001US Intel Solid State Drive 525 Series 4 0 Pin and Signal Descriptions 4 1 Pin Locations Figure 3 Layout of Signal and Power Segment Pins AREA DETAIL TOP PN 1 PIN 51 PN2 AREA DETAIL BOTTOM PN 52 4 2 Signal Descriptions Table 9 Serial ATA Power Pin Definitions Pin Function Definition Pl Reserved No Connect P2 3 3V 3 3 V Source P3 Reserved No Connect P4 GND Return Current Path P5 Reserved No Connect P6 1 5 V 1 5 V Source P7 Reserved No Connect P8 Reserved No Connect P9 GND Return Current Path P10 Reserved No Connect P11
15. bit address feature set 104 V Oh Streaming transfer time PIO 105 F 0001h Reserved 106 F 4000h Physical sector size logical sector size 107 F Oh Inter seek delay for SO 7779 acoustic testing in microseconds 108 111 F varies Unique ID 112 115 F Oh Reserved for world wide name extension to 128 bits 116 V Oh Reserved for technical report 117 118 F Oh Words per logical sector 119 F 401Ch Supported settings 120 F 401Ch Command set feature enabled supported 121 126 F Oh Reserved 127 F Oh Removable Media Status Notification feature set support 128 V 0021h Security status 129 159 X varies Vendor specific 160 F Oh CompactFlash Association CFA power mode 1 161 168 X Oh Reserved for assignment by the CFA 169 X 0001h Data set management Trim attribute support Intel amp Solid State Drive 525 Series Product Specification December 2012 26 Order Number 328354 001US m e Intel Solid State Drive 525 Series n tel Table 16 Returned Sector Data Fixed Word V Variable Default Value Description X Both 170 173 F Oh Additional Product Identifier 174 175 F Oh Reserved 176 205 V Oh Current media serial number 206 X 0021h SCT Command Transport 207 208 X Oh Reserved 209 X 4000h Alignment of logical blocks within a physical block 210 211 X Oh Write Read Verify Sector Count Mode 3 DWord 212 213 X Oh Write Read Verify Sector Count Mode 2 DWord 214 X Oh NV Cache Capabilit
16. ditional wear can be put on the device Total LBAs Written The raw value of this attribute reports the F1h total number of sectors written by the host 1 1 0 0 1 0 system The raw value is increased by 1 for every 65 536 sectors 32MB written by the host 0 none Total LBAs Read The raw value of this attribute reports the F2h total number of sectors read by the host 1 1 0 0 1 0 system The raw value is increased by 1 for every 65 536 sectors 32MB read by the host 0 none Total NAND Writes F9h Raw value reports the number of writes to 1 1 0 0 1 0 0 none NAND in 1 GB increments Table 11 defines the SMART Attribute status flags Table 11 SMART Attribute Status Flags Status Flag Description Value 0 Value 1 SP Self preserving attribute Not a self preserving attribute Self preserving attribute EC Event count attribute Not an event count attribute Event count attribute ER Error rate attribute Not an error rate attribute Error rate attribute PE Performance attribute Not a performance attribute Performance attribute oc Online collection attribute Collected ae offline aay ERES PW Pre fail warranty attribute Advisory Pre fail 5 4 2 SMART Logs The Intel SSD 525 Series implements the following Log Addresses 00h 02h 03h 06h and 07h The Intel SSD 525 Series implements host vendor specific logs addresses 80h 9Fh as read and write scratchpa
17. ds where the default value is zero 0 Intel SSD 525 Series does not write any specific values to these logs unless directed by the host through the appropriate commands The Intel SSD 525 Series also implements a device vendor specific log at address A9h as a read only log area with a default value of zero 0 Intel amp Solid State Drive 525 Series December 2012 Product Specification Order Number 328354 001US 17 E I n te Intel amp Solid State Drive 525 Series 5 5 Device Statistics In addition to the SMART attribute structure statistics pertaining to the operation and health of the Intel SSD 525 Series can be reported to the host on request through the Device Statistics log as defined in the ATA specification The Device Statistics log is a read only GPL SMART log located at read log address 0x04 and is accessible using READ LOG EXT READ LOG DMA EXT or SMART READ LOG commands Table 12 lists the Device Statistics supported by the Intel SSD 525 Series Table 12 Device Statistics Log Page Offset Description Equivalent SMART attribute if applicable 0x00 List of Supported Pages 0x08 Power Cycle Count OCh 0x10 Power On Hours 09h 0x18 Logical Sectors Written Elh 0x01 General Statistics Num Write Commands incremented 0x20 by one for every host write command 0x28 Logical Sectors Read F2h Num Read Commands incremented 0x30 a by one for every host write com
18. ed On the recorded value for power on hours does not include the time that the device is in a slumber state If DIPM is turned Off the recorded value for power on hours should match the clock time as all three device states are counted active idle and slumber 0 none OCh Power Cycle Count The raw value of this attribute reports the cumulative number of power cycle events over the life of the device 0 none AAh Available Reserved Space 10 ABh Program Fail Count The raw value of this attribute shows total count of program fails and the normalized value beginning at 100 shows the percent remaining of allowable program fails 0 none ACh AEh Erase Fail Count The raw value of this attribute shows total count of erase fails and the normalized value beginning at 100 shows the percent remaining of allowable erase fails Unexpected Power Loss The raw value of this attribute reports the cumulative number of unsafe unclean shutdown events over the life of the device An unsafe shutdown occurs whenever the device is powered off without STANDBY IMMEDIATE being the last command 0 none 0 none B7h SATA Downshift Count The count of the number of times SATA interface selected lower signaling rate due to error 10 B8h End to End Error Detection Count Reports number of errors encountered during end to end error detection within the SSD data path
19. en Failure MTBF 1 200 000 hours Shock operating and non operating 1 000 G 0 5 msec Vibration Operating 2 17 Germs 5 700 Hz Non operating 3 13 Gays 5 800 Hz Certifications and Declarations C Tick BSMI KCC Microsoft WHCK VCCI SATA IO Product Ecological Compliance RoHS Order Number 328354 001US December 2012 E I n te Intel amp Solid State Drive 525 Series Ordering I nformation Contact your local Intel sales representative for ordering information INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL PRODUCTS NO LICENSE EXPRESS OR IMPLIED BY ESTOPPEL OR OTHERWISE TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT EXCEPT AS PROVIDED IN INTEL S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS INTEL ASSUMES NO LIABILITY WHATSOEVER AND INTEL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATI NG TO SALE AND OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE MERCHANTABILITY OR INFRINGEMENT OF ANY PATENT COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT UNLESS OTHERWISE AGREED IN WRITING BY INTEL THE INTEL PRODUCTS ARE NOT DESIGNED NOR INTENDED FOR ANY APPLICATION IN WHICH THE FAILURE OF THE INTEL PRODUCT COULD CREATE A SITUATION WHERE PERSONAL INJ URY OR DEATH MAY OCCUR Intel may make changes to specifications and product descriptions at any time without notice Designers must not
20. er usage Intel amp Solid State Drive 525 Series Product Specification December 2012 4 Order Number 328354 001US m e Intel Solid State Drive 525 Series n tel 2 0 Product Specifications 2 1 Capacity Table 1 User Addressable Sectors Intel SSD 525 Series gnformatted Capacity Total User Addressable Sectors in LBA Mode 30 GB 58 626 288 60 GB 117 231 408 120 GB 234 441 648 180 GB 351 651 888 240 GB 468 862 128 Note 1 GB 1 000 000 000 bytes 1 sector 512 bytes LBA count shown represents total user storage capacity and will remain the same throughout the life of the drive The total usable capacity of the SSD may be less than the total physical capacity because a small portion of the capacity is used for NAND flash management and maintenance purposes 2 2 Performance The data compression engine in the Intel SSD 525 Series controller optimizes performance based on the data pattern of the workload This section provides both compressible and incompressible Input Output Operations Per Second LOPS and sustained sequential read and write bandwidth specifications Table 2 Compressible Performance Intel SSD 525 Series Specification Unit 60 GB 30 GB 120 GB 180 GB 240 GB Random 4 KB Read up to IOPS 5 000 15 000 25 000 50 000 50 000 Random 4 KB Write up to IOPS 80 000 80 000 80 000 80 000 80 000 Random 4 KB Write TYP IOPS 10 000 23 000 40 000 60 000 60 000 3 TL Wes 500 550 550
21. esGtsseessscasteceveceenseasisieastedwesetusscssesccstusedessssessccceeccensseesstees 22 8 0 Terms and Actonyrins ooo o sone onto tona i peak NR IS POR ERN SS PE RRRR SEE RRRR cosoassecoosssaceosssiesesosscs 22 9 0 REVISION HISEOFy chest EE A hee Oye t SERERE EE OE Pa E EERRR E EN 23 Appendix IDENTIFY DEVICE Command Data c cesses eese eese eene enne nn nnns n nost n nasse nenas 24 Intel amp Solid State Drive 525 Series December 2012 Product Specification Order Number 328354 001US 3 m e n tel Intel amp Solid State Drive 525 Series 1 0 Overview This document describes the specifications and capabilities of the Intel amp Solid State Drive 525 Series Intel SSD 525 Series The Intel SSD 525 Series delivers small form factor storage and leading performance for Serial Advanced Technology Attachment SATA based computers in capacities ranging from 30GB to 240GB By combining Intel s high quality 25nm NAND flash memory technology with SATA 6Gb s interface support the Intel SSD 525 Series delivers sequential read speeds of up to 550 MB s and sequential write speeds of up to 520 MB s The case less mSATA mini SATA design has a significantly smaller footprint than a 2 5 inch hard disk drive HDD and enables fast read write access times and a significant I O and throughput performance improvement as compared to HDDs This design makes it ideal for new and innovative small form factor computing platfor
22. h Laboratory RRL Ministry of Information and Communication Republic of Korea Microsoft WHCK Microsoft Windows Hardware Certification Kit RoHS Compliant VCCI Restriction of Hazardous Substance Directive Voluntary Control Council for Interface to cope with disturbance problems caused by personal computers or facsimile SATA IO Indicates certified logo program from Serial ATA International Organization Low Halogen December 2012 Applies only to brominated and chlorinated flame retardants BFRs CFRs and PVC in the final product Intel components as well as purchased components on the finished assembly meet J S 709 requirements and the PCB substrate meet IEC 61249 2 21 requirements The replacement of halogenated flame retardants and or PVC may not be better for the environment Intel amp Solid State Drive 525 Series Product Specification Order Number 328354 001US 21 intel 7 0 References Intel Solid State Drive 525 Series Table 14 identifies the standards information referenced in this document Table 14 Standards References Date or Rev Title Location Sept 2010 Solid State Drive SSD Requirements and Endurance Test Method http www jedec org standards docume p JESD218 nts docs jesd218 Dec 2008 VCCI http www vcci jp vcci_e http qdms intel com June 2009 RoHS Click Search MDDS Database and search for material description datasheet August 2009
23. ies 215 216 X Oh NV Cache Size in Logical Blocks DWord 217 X 0001h Nominal media rotation rate 218 X Oh Reserved 219 X Oh NV Cache Options 220 X Oh Write Read Verify feature set 221 X Oh Reserved 222 X 103Fh Transport major version number 223 X Oh Transport minor version number 224 229 X Oh Reserved 230 233 X Oh Extended Number of User Addressable Sectors QWord 234 x 0002h EAE byte data blocks per DOWNLOAD MICROCODE 235 X 0400h Kanam eee E data blocks per DOWNLOAD MICROCODE 236 254 X Oh Reserved 255 X varies Integrity word Notes F Fixed The content of the word is fixed and does not change For removable media devices these values may change when media is removed or changed V Variable The state of at least one bit in a word is variable and may change depending on the state of the device or the commands executed by the device X For V The content of the word may be fixed or variable Intel amp Solid State Drive 525 Series December 2012 Product Specification Order Number 328354 001US 27
24. intel Intel Solid State Drive 525 Series Capacity 30 60 120 180 240 GB Components Intel 25nm NAND Flash Memory Multi Level Cell MLC Form Factor mSATA full size Thickness 3 7 mm Weight lt 10 grams SATA 6Gb s Bandwidth Performance lometer Queue Depth 32 Sustained Sequential Read up to 550 MB s Sustained Sequential Write up to 520 MB s Read and Write IOPS lometer Queue Depth 32 Random 4 KB Reads Up to 50 000 IOPS Random 4 KB Writes Up to 80 000 I OPS Latency average sequential Read 80 us TYP Write 85 us TYP Data Compression AES 128 bit Encryption End to end Data Protection Compatibility Intel SSD Toolbox with Intel SSD Optimizer Intel Data Migration Software Intel Rapid Storage Technology SATA Revision 3 0 ACS 2 SSD enhanced SMART ATA feature set Native Command Queuing NCQ command set Data Set Management Command Trim attribute 1 Performance values vary by capacity 2 Random 4 KB writes measured using out of box SSD Product Specification Power Management 3 3 V SATA Supply Rail SATA Link Power Management LPM Power Active MobileMark 2007 Workload 300 mW TYP Idle 250 mW TYP Temperature Operating 0 C to 70 C Non Operating 55 C to 95 C Reliability Uncorrectable Bit Error Rate UBER lt 1 sector per 1019 bits read Mean Time Betwe
25. mand 0x08 Num Reported Uncorrectable Errors BBh 0x04 General Errors Statistics Num Resets Between Command 0x10 Acceptance and Completion 0x08 Num Hardware Resets 0x06 Transport Statistics 0x10 Num ASR Events 0x18 Num Interface CRC Errors E9h This statistic counts up from 0 0x07 Solid State Device Statistics 0x08 Percentage Used Endurance Indicator rather than down from 100 and may go beyond 100 for drives that exceed their expected lifetime 5 6 SMART Command Transport SCT With SMART Command Transport SCT a host can send commands and data to an SSD and receive status and data from an SSD using standard write read commands to manipulate two SMART Logs Log Address EOh SCT Command Status used to send commands and retrieve status e Log Address E1h SCT Data Transfer used to transport data 5 7 Data Set Management Command Set The Intel SSD 525 Series supports the Data Set Management command set Trim attribute which consists of DATA SET MANAGEMENT Intel amp Solid State Drive 525 Series Product Specification December 2012 18 Order Number 328354 001US m e Intel amp Solid State Drive 525 Series n tel 5 8 Host Protected Area Command Set The Intel SSD 525 Series supports the Host Protected Area command set which consists of READ NATIVE MAX ADDRESS SET MAX ADDRESS READ NATIVE MAX ADDRESS EXT SET MAX ADDRESS EXT 5 9 48 Bit Address Command Set The Intel SSD 525 Series supports the
26. ms that have size and weight requirements that traditional 2 5 inch or 1 8 inch HDDs cannot meet such as netbooks thin and light systems mini and sub notebooks all in one computers and embedded platforms As compared to standard SATA HDDs Intel SSD 525 Series offers these key features High I O and throughput performance Low power Increased system responsiveness High reliability Enhanced ruggedness Small form factor Minimum weight The Intel SSD 525 Series also offers additional key features such as Advanced Encryption Standard AES 128 bit Encryption AES 128 bit encryption is an industry standard in data security providing a hardware based mechanism for encryption and decryption of user data Utilizing a 128 bit encryption key AES encryption when combined with an ATA drive password helps protect user data e End to End Data Protection End to end data protection helps protect data from being corrupted across the data path by using cyclic redundancy check CRC parity and error correction code ECC checks in the data path from the host interface to the NAND and back Data Compression Data compression helps improve performance and endurance by automatically compressing information sent to the SSD so that less data has to be processed and stored on the NAND The amount of data that can be compressed depends on the type of data Note 1 The Intel SSD 525 Series is currently not validated for data cent
27. ommands are defined in this section 5 1 ATA General Feature Command Set General Feature command set non PACKET which consists of e EXECUTE DEVICE DIAGNOSTIC FLUSH CACHE IDENTIFY DEVICE Note See the Appendix for details on the sector data returned after issuing an IDENTIFY DEVICE command e READ DMA READ SECTOR S READ VERIFY SECTOR S SEEK SET FEATURES WRITE DMA WRITE SECTOR S READ MULTIPLE SET MULTIPLE MODE WRITE MULTIPLE The Intel SSD 525 Series also supports the following optional commands READ BUFFFER WRITE BUFFER e NOP DOWNLOAD MICROCODE 5 2 Power Management The Intel SSD 525 Series supports several power management feature sets as defined by the ATA specification general Power Management feature set Advanced Power Management feature set and Power Up In Standby PUIS feature set The Advanced Power Management and PUIS features can be enabled or disabled using the SET FEATURES command The Power Management feature set includes the following commands CHECK POWER MODE IDLE DLEIMMEDIATE SLEEP STANDBY STANDBY IMMEDIATE Intel amp Solid State Drive 525 Series December 2012 Product Specification Order Number 328354 001US 13 E I n te Intel Solid State Drive 525 Series 5 3 Security Mode Feature Set The Intel SSD 525 Series supports the Security Mode command set which consists of SECURITY SET PASSWORD SECURITY UNLOCK SECURITY
28. r Managerernt ce dI aeta deste aiene e a aaaeeeaa deae oic e ee odd 13 5 3 Security Mode Feature Set ette ede oet eoe ee edente dense ook e Pe anon 14 54 SMART Comtrnand Set erecto cedente dede o ee eee donet ate dence ooo e ie acu 14 5 5 DEVICE Statistics cn emere rc v ede E asduxs eese dde ras Do purse udo U pus dex resp de TE SNR 18 5 6 SMART Command Transport SCT c cccccssccccsessececeeseceeseaececsesaececsesaeeeceesaeeeesesaeeeeeeaaes 18 5 7 Data Set Management Command Set ssssssssseseees esent nnns ener an 18 5 8 Host Protected Area Command Set cccseesssssseceeecessessaeeeeeeeceeseseeaeeesecssessesneaeseeeesseesees 19 5 9 48 Bit Address Command Set cssscccccecsssesscsececececsesesseaeeeccescesseseeaeeeeecesessesnsaeeeeeesseeeees 19 5 10 General Purpose Log Command Set cccecsessscccccecsssessaeeeeeescessesneaeeeeeesseesesneaeeeeeesseeeees 19 5 11 Native Command QueUING ccccsccccccecsssessnseeeeeeeceesessuseeeeeessesseseeaeceeecsseesessaeeeeeseseeeas 19 5 12 Software Settings Preservation ccccccccccssssssssceeccecscsessseceecesseesesseaeeesecsssesesesaeeeseessseeees 20 5 13 SATA Link Power Management LPM csccccccsscecsesseceeeesseeecsssaeceesesaeceesesaeeeesesaeeeeseaas 20 6 0 Certifications and Declarations sciccissscsesccscescedcsvediscavcsssetessecasdaccdssstocsesedcsacdestcoddassassvestcouse tds 21 7 0 References sscesesscesectissvessesceeis cesse
29. rely on the absence or characteristics of any features or instructions marked reserved or undefined Intel reserves these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them The information here is subject to change without notice Do not finalize a design with this information The products described in this document may contain design defects or errors known as errata which may cause the product to deviate from published specifications Current characterized errata are available on request Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order Copies of documents which have an order number and are referenced in this document or other Intel literature may be obtained by calling 1 800 548 4725 or go to http www intel com design literature htm Low Halogen applies only to brominated and chlorinated flame retardants BFRs CFRs and PVC in the final product Intel components as well as purchased components on the finished assembly meet JS 709 requirements and the PCB substrate meet IEC 61249 2 21 requirements The replacement of halogenated flame retardants and or PVC may not be better for the environment Intel and the Intel logo are trademarks of Intel Corporation in the U S and other countries Other names and brands may be claimed as the property of others Copyright 2012 In
30. s supported by the Intel SSD 525 Series Table 13 Device Certifications and Declarations Certification Description CE Compliant Low Voltage DIRECTIVE 2006 95 EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 12 December 2006 and EMC Directive 2004 108 EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 15 December 2004 Per EN 50581 2012 Technical documentation for the assessment of electrical and electronic products with respect to the restriction of hazardous substances UL Certified Certified Underwriters Laboratories Inc Bi National Component Recognition UL 60950 1 2nd Edition 2007 03 27 Information Technology Equipment Safety Part 1 General Requirements CSA C22 2 No 60950 1 07 2nd Edition 2007 03 Information Technology Equipment Safety Part 1 General Requirements C Tick Compliant Compliance with the Australia New Zealand Standard AS NZS3548 and Electromagnetic Compatibility EMC Framework requirements of the Australian Communication Authority ACA BSMI Compliant Compliance to the Taiwan EMC standard CNS 13438 Information technology equipment Radio disturbance Characteristics limits and methods of measurement as amended on June 1 2006 is harmonized with CISPR 22 2005 04 KCC Compliance with paragraph 1 of Article 11 of the Electromagnetic Compatibility Control Regulation and meets the Electromagnetic Compatibility EMC Framework requirements of the Radio Researc
31. tel Corporation All rights reserved Intel amp Solid State Drive 525 Series Product Specification December 2012 2 Order Number 328354 001US m e Intel Solid State Drive 525 Series n tel Contents 1 0 le Tul ERS 4 2 0 Product Specifications eei eois evades sedvecassscwacesssvedeasstuecaesssvaceasstvsceacsevedaassvoceassavcsaass aves 5 2 1 Sr P r 5 2 2 Performances eet eer inte vie EATA tee eu v sso ovS SER EE SEES 5 2 3 Electrical Chatacteristics re eec e edet reete aeta edet cates ARE rx eakat 7 2 4 Environmental CONItIONS ccccsessececeeeceesecseaeeececsceeseaaaececeesseesesaeaeeeeeesseeseaeaeeeeeesseeees 7 2 5 Product Regulatory Compliance esses enne nnne nenas sns nnn an 8 2 6 Reliability sitem HERO ees sree ate estan ae 9 3 0 Mechanical Information ise coset correre enr Ee rero eerte ce Ebo Eo ree eive oi ESEESE ND ESSE SONES ENNES 10 4 0 Pin and Signal Descriptions 1 o eoe eos tuus no oo uaa na ee nhan a een u aba s Itn n Rasa eeu R PR a er na aia 11 4 1 Pin Locations ersero E 11 4 2 Signal Descriptions oed suse iraa AA AEEA Pega DRY AER OAAS 11 5 0 Supported Command Sets eei oe pani oen no ta tua n n soU u uua aa EU ya So ESPERE REDDE ERR REPRE ERR RD ERRRR Ro DR EO 13 5 1 ATA General Feature Command Set sssssssssssseseeee eene nennen ares n nenne nsns nnne 13 5 2 Powe
32. ters 20 21 X Oh Retired 22 X Oh Obsolete 23 26 F varies Firmware revision 8 ASCII characters 27 46 F varies Model number Intel Solid State Drive 47 F 8010h Cn er of sectors transferred per interrupt on 48 F 4000h Reserved 49 F 2F00h Capabilities 50 F 4000h Capabilities 51 52 X Oh Obsolete 53 F 0007h Words 88 and 70 64 valid 54 X 3FFFh Obsolete Number of logical cylinders 16 383 55 X 0010h Obsolete Number of logical heads 16 56 X 003Fh Obsolete Number of logical sectors per logical track 63 57 58 X OOFBFC10h Obsolete Intel Solid State Drive 525 Series Product Specification December 2012 24 Order Number 328354 001US Intel Solid State Drive 525 Series Table 16 Returned Sector Data F Fixed Word V Variable Default Value Description X Both 59 V 0110h t sectors transferred per interrupt on multiple 60 61 F varies Total number of user addressable sectors 62 X Oh Obsolete 63 F 0007h Multi word DMA modes supported selected 64 F 0003h PIO modes supported 65 F 0078h Minimum multiword DMA transfer cycle time per word 66 F 0078h Manufacturer s recommended multiword DMA transfer cycle time 67 F 0078h Minimum PIO transfer cycle time without flow control 68 F 0078h Minimum PIO transfer cycle time with IORDY flow control 69 F 4010h Additional Supported 70 F Oh Reserved 71 74 F Oh Reserved for IDENTIFY PACKET DEVICE command 75 F 001Fh Queue depth
Download Pdf Manuals
Related Search