Home

Supermicro AOC-SGP-I4

1. means the jumper is on and Open means the jumper is off the pins 3 3V Standby Power Enable The 3 3V Standby Power Enable jumper is located at J2 on the add on card Refer to the layout on Page 2 1 for the location of the jump er Close Pins 1 amp 2 to enable 3 3V Standby Power for Wake on LAN support The default setting is Disabled Chapter 2 Hardware Components 2 pin Jumper Jumper Cap e Jumper Off Open J Pins 1 2 On Closed 3 3V Standby PWR Enable Jumper Settings Jumper setting Definition On Enabled 1 2 See the note below off Disabled default SUPER AOC SGP i4 Add on Card User s Guide Notes Chapter 3 Installation 3 1 Chapter 3 Installation Static Sensitive Devices Electrostatic Discharge ESD can damage electronic components To avoid dam aging your add on card it is important to handle it very carefully The following measures are generally sufficient to protect your equipment from ESD Precautions Use a grounded wrist strap designed to prevent static discharge Touch a grounded metal object before removing the add on card from the antistatic bag Handle the add on card by its edges only do not touch its components or peripheral chips Put the add on card back into the antistatic bags when not in use For grounding purposes make sure that your system chassis provides excellent conductivity between the p
2. Representation Options 1st Product Family AOC Add On Card Form Factor U UIO S Standard P Proprietary C MicroLP Product Type Speed G GbE 1Gb s TG 10GbE 10Gb s IBF IB FDR 56Gb s IBQ IB QDR 40Gb s INF InfiniBand DDR 20Gb s Chipset Model Optional N Niantec 82599ES P Powerville i350 Chipset Manufacturer i Intel m Mellanox Number of Ports 1 1 port 2 2 ports 4 4 ports Connector Type Optional S SFP T 10GBase T SMC Networking Add on Cards SG i2 SG i4 SGP i4 STG i2T STGN i2S STG i2 UIBF m1 UINF m2 UIBQ m1 UIBQ m2 CGP i2 CG i2 CIBF m1 CTG i1S Form Factor Interface Controller Connection Dimension without Brackets Hx L Standard LP PCI E x4 Intel 82575EB 2 RJ45 1Gb port 2 13 2cm x 2 5 6 4cm Standard LP PCI E x8 Intel 82576EB 4 RJ45 1Gb port 8 14 7cm x 2 5 6 4cm Standard LP PCI E x4 Intel i350 4 RJ45 1Gb port 9 9 9cm x 2 5 6 4cm Standard LP PCI E x8 Intel X540 2 RJ45 10Gb port 13 7cm x 2 5 6 4cm Standard LP PCI E x8 Intel 82599ES 2 SFP 10Gb port 4 13 7cm x 2 5 6 4cm Standard LP PCI E x8 Intel 82598EB 2 CX4 10Gb port 6 14 1cm x 2 5 6 4cm Proprietary LP PCI Ex4 Intel 82576EB 2 RJ45 1Gb port 8 9 6cm x 2 5 6 4cm PCI Ex8 Intel 82571EB 4 RJ45 1Gb port 6 16 7cm x 3 9 9 8m PCI Ex8 Intel 82598EB 2 CX4 10Gb port 6 16 7cm
3. 886 2 8226 3990 886 2 8226 3991 www supermicro com tw support supermicro com tw Technical Support 886 2 8226 5990 Technical Support SUPER AOC SGP i4 Add on Card User s Guide Table of Contents Preface Chapter 1 Overview 1 1 Overview T2 Key Feature Su sul a dalal kk rec thaea dikan d yan z n Kana kiy k n x da du b na badey b Ka ea H Han aya da d k 1 1 13 SpecifiCatlOnS kou Aba Gee ee A jan kedi Ee da a N rana weva W k Ma k kan 1 1 Chapter 2 Hardware Components 2 1 Add On Card Image and LaygOuUt kk kk kk ke 2 1 2 2 Major Compoll lliS y na xis kaa n kaye yi Naa ayan AW ayas Ve n Xula Ae Na aatals 2 1 2 3 Connectors LAN Ports and LAN LED Indicators pp 2 2 Ethernet Ports s Ri EE SS 2 2 2 4 Jumpers 3 3V Standby Power JUMPE aerisire 2 3 Explanation of JUMPGMS sax sasaniyan xin a HEKA RN AE BRA SERINE ka AW 2 3 3 3V Standby Power Ena bl a saye w nanan din nika a 2 3 Chapter 3 Installation 3 1 Static Sensitive DEVICE Ss aa uy oe a ow ad heat edna E EE 3 1 Precautions LI PACKING soaa N a aa a a N Ea 32 Before INStallation six a learn kana Wi nina ara n kl W kak daka 3 2 3 3 Installing the Add on Card pp 3 2 3 4 Installing the Windows Operating System E eke 3 3 3 5 Installing the Linux Operating System pp 3 3 Build a Binary RPM Package 3 6 Building the Driver Manually a u sula dkakeseaynnan
4. PCI connector Secure the add on card to the chassis If required use the screw that you previously removed Attach any necessary external cables to the add on card Replace the chassis cover Plug the power cord into the wall socket and power up the system 3 2 Chapter 3 Installation 3 4 Installing the Windows Operating System Follow the steps below to install the drivers needed for your Windows OS support The controller comes with a driver on the CD ROM CDR NIC 1 Run the CDR NIC If you do not have a product CD ROM download drivers from the Supermicro Support Website and then transfer them to your system 2 When the SUPERMICRO window appears click on the computer icon next to the product model SUPERMICRO Add On Card Drivers and Tools WinXP x 10GbE Adapters 2a UTG i2 STG i2 STGN i25 STG i2T SUPERMICR IB Adapters Drivers amp Tools UINF m2 UIBQ m1 UIBQ m2 RIUG lt BQ CIBF m1 UIBF mi IB drivers gt 1B Adapters A UINF m2 UIBQ m1 UIBO m2 R1UG iBQ CIBF m1 UIBF m1 10GbE drivers X GbE Adapters AN 2 UG i4 PG i2 SG i2 SB i4 CG 12 SGP i4 CGP i2 K a Read Product Description and Manual gt S For more information please visit SUPERMICRO s web site SUPERMICRO Computer Inc f Note If the FOUND NEW HARDWARE WIZARD screen displays on your system click CANCEL 3 Click on INSTALL DRIVERS AND SOFTWARE 4 Follow the prompts to complete
5. nakin ka kada kkke kk arek KNK vi Chapter 1 Overview Chapter 1 Overview 1 1 Overview Congratulations on purchasing your add on card from an acknowledged leader in the industry Supermicro products are designed with the utmost attention to detail to provide you with the highest standards in quality and performance For product support and updates please refer to our website at http Awww supermicro com products nfo networking cfm adapter 1 2 Key Features The key features of this add on card include the following Low Profile Standard Form Factor in 3 9 inch in Length e PCI Express 2 1 2 5GT s or 5GT s Four RJ 45 ports e Intel I O Acceleration Technology I O AT supported Support of VMDq Next Generation VMDq and PC SIG SR IOV for Virtualized Environments Jumbo Frame Support of up to 9 5KB IEEE 802 3az Energy Efficient Ethernet EEE Low Power Consumption 5W Typical iSCSI Remote Boot support e Flexible I O Virtualization and Quality of Service QoS PXE Boot Support e ROHS compliant 6 6 1 3 Specifications General e Intel i350 GbE controller e Compact size low profile standard form factor 1 1 SUPER AOC SGP i4 Add on Card User s Guide e PCI E 2 1 x4 2 5GT s or 5GT s interface e Four RJ 45 connectors e Intel PROSet Utility for Windows Device Manager e Intel I O Acceleration Technology I O AT e Power consumption about 5W Ethernet Features e I
6. x 3 9 9 8cm PCI E x8 Mellanox ConnectX 3 1 QSFP 56Gb port 6 14 0cm x 2 5 6 4cm PCI E x8 Mellanox ConnectX 2 2 CX4 20Gb port 5 14 0cm x 2 5 6 4cm PCI E x8 Mellanox ConnectX 2 1 QSFP 40Gb port 6 14 3cm x 2 5 6 4cm PCI E x8 Mellanox ConnectX 2 2 QSFP 40Gb port 14 3cm x 2 5 6 4cm MicroLP PCI E x4 Intel i350 2 RJ45 1Gb port 5 11 3cm x 1 3 3 4cm MicroLP PCI E x4 Intel 82580 2 RJ45 1Gb port 5 11 3cm x 1 3 3 4cm MicroLP PCI E x8 Mellanox ConnectX 3 1 QSFP 56Gb port 5 11 3cm x 1 3 3 4cm MicroLP PCI E x8 Intel 82599EN 1SFP 10Gb port 11 3cm x 1 3 3 4cm Headquarters Address Tel Fax Email Website Europe Address Tel Fax Email Asia Pacific Address Tel Fax Website Email Tel Preface Contacting Supermicro Super Micro Computer Inc 980 Rock Ave San Jose CA 95131 U S A 1 408 503 8000 1 408 503 8008 marketing supermicro com General Information support supermicro com Technical Support www supermicro com Super Micro Computer B V Het Sterrenbeeld 28 5215 ML s Hertogenbosch The Netherlands 31 0 73 6400390 31 0 73 6416525 sales supermicro nl General Information support supermicro nl Technical Support rma supermicro nl Customer Support Super Micro Computer Inc 4F No 232 1 Liancheng Rd Chung Ho 235 Taipei County Taiwan R O C
7. EEE 802 3 auto negotiation for speed duplex and flow control e IEEE 802 3x and 802 3z compliant flow control support e Automatic cross over detection function MDI MDI X e 1Gb s Ethernet IEEE 802 3 802 3u 802 3ab PHY specifications compliant e IEEE 1588 protocol and 802 1AS implementation Power Management and Efficiency e IEEE 802 3az Energy Efficient Ethernet EEE which reduces power consump tion of the PHY by about 50 e DMA Coalescing reduces platform power consumption e Active State Power Management ASPM support e LAN disable function e MAC Power Management controls e Low Power Link Up Link Speed Control Virtualization Features e VM to VM Packet forwarding Packet Loopback e Eight TX and RX queue pairs per port to support VMWare NetQueue and Microsoft VMQ 1 2 Chapter 1 Overview Flexible Port Partitioning 32 Virtual Functions PC SIG SR IOV implementation IEEE 802 1q VLAN support IEEE 802 1q advanced packet filtering Performance Features TCP UDP IPv4 and IPv6 checksum offloads to improve CPU usage Low La tency Interrupts Tx TCP segmentation offload IPv4 IPv6 increases throughput and lowers processor usage Receive Side Scaling RSS for Windows environment Scalable I O for Linux environments Jumbo Frames support up to 9 5K Bytes Intelligent interrupt generation Remote Boot Options Preboot eXecution Environment PXE support iSCSI remote boot for Windows Linux and VMwar
8. SUPER AOC SGP i4 User s Guide Revision 1 0 The information in this User s Guide has been carefully reviewed and is believed to be accurate The vendor assumes no responsibility for any inaccuracies that may be contained in this document and makes no commitment to update or to keep current the information in this user s guide or to notify any person or organization of the updates Please Note For the most up to date version of this user s guide please see our Website at www supermicro com Super Micro Computer Inc Supermicro reserves the right to make changes to the product described in this user s guide at any time and without notice This product including software and documentation is the property of Supermicro and or its licensors and is supplied only under a license Any use or reproduction of this product is not allowed except as expressly permitted by the terms of said license IN NO EVENT WILL SUPER MICRO COMPUTER INC BE LIABLE FOR DIRECT INDIRECT SPECIAL INCIDENTAL SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES IN PARTICULAR SUPER MICRO COMPUTER INC SHALL NOT HAVE LIABILITY FOR ANY HARDWARE SOFTWARE OR DATA STORED OR USED WITH THE PRODUCT INCLUDING THE COSTS OF REPAIRING REPLACING INTEGRATING INSTALLING OR RECOVERING SUCH HARDWARE SOFTWARE OR DATA Any disputes arising between the manuf
9. acturer and the customer shall be governed by the laws of Santa Clara County in the State of California USA The State of California County of Santa Clara shall be the exclusive venue for the resolution of any such disputes Supermicro s total liability for all claims will not exceed the price paid for the hardware product FCC Statement This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the manufacturer s instruction manual may cause harmful interference with radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case you will be required to correct the interference at your own expense California Best Management Practices Regulations for Perchlorate Materials This Perchlorate warning applies only to products containing CR Manganese Dioxide Lithium coin cells Perchlorate Material special handling may apply See www dtsc ca gov hazardouswaste perchlorate WARNING Handling of lead solder materials used in this product may expose you to lead a chemical known to the State of California to cause birth defects and other reproduc
10. amp LED ler 3 RJ45 LAN Port 2 amp LED 4 RJ45 LAN Port 3 amp LED 5 RJ45 LAN Port 4 amp LED 6 3 3V Standby Power Enable Jumper SUPER AOC SGP i4 Add on Card User s Guide 2 3 Connectors LAN Ports and LAN LED Indicators Ethernet Ports Four Ethernet ports LAN1 LAN2 LAN3 LAN4 are located on the add on card Plug the RJ45 type cables into LAN Port1 LAN Port4 to provide Ethernet connections Refer to the add on card layout on Page 2 1 for the locations of the LAN ports GLAN Port LEDs Four LAN ports LAN 1 LAN 4 are located on the add on card Each Eth Activity i ernet LAN port has two LEDs The LED on the left indicates activity while the other LED on the right may be green orange or off to indicate the speeds of the connections See the table at right for more information GLAN Port LEDs LED Color Definition Activity Amber LAN Active Blinking Link Orange 1Gb s Link Speed Green 100Mb s Link Speed Off 10Mb s Link Speed or No Connection 2 2 2 4 Jumpers Explanation of Jumpers To modify the operation of the add on card a jumper can be used to choose between optional settings A jumper creates shorts between two pins to change the function of the connector Pin 1 is identified with a square solder pad on the printed circuit board See the add on card layout on Page 2 1 for the jumper location Fatal On two pin jumpers Closed
11. e OS Support Windows XP SP3 Vista SP2 7 SP1 2003 SP2 2008 SP2 2008 R2S RedHat EL 5 5 6 0 SuSe SLES 10 SP3 11 SP1 FreeBSD 8 0 VMware ESX 4 0 4 1 5 0 Xen 1 3 SUPER AOC SGP i4 Add on Card User s Guide Cables Support e RJ 45 Category 5 5e up to 100m Operating Conditions e Operating temperature 0 C to 55 C 32 F to 131 F Storage temperature 40 C to 70 C 40 F to 158 F Physical Dimensions e Card PCB dimensions 9 91cm 3 90in x 6 35cm 2 50in L x H e Height of end brackets standard 12cm 4 725in low profile 7 94cm 3 13in Compliance Environmental e RoHS Compliant 6 6 Pb Free RoHS complaint Go Supported Platforms e Motherboards with minimum PCI E x4 slot e Server Systems with low profile or full height PCI E x4 expansion slot Note Please note that this product is only available as an integrated solution with Supermicro server systems For the most current product information visit www supermicro com 1 4 Chapter 2 Hardware Components Chapter 2 Hardware Components 2 1 Add On Card Image and Layout The AOC SGP i4 Image PA U The AOC SGP i4 Layout AO D i4 o gt zz 1 a S Intel 1350 o q e z2 E LAN Control a e om Oo zE om S e oO e z ca 5 B PWR 3 9 K 2 2 Major Components The following major components are installed on the AOC SGP i4 1 Intel 1350 LAN Control 2 RJ45 LAN Port 1
12. guide Returning Merchandise for Service A receipt or copy of your invoice marked with the date of purchase is required before any warranty service will be rendered You can obtain service by calling your ven dor for a Returned Merchandise Authorization RMA number When returning the motherboard to the manufacturer the RMA number should be prominently displayed on the outside of the shipping carton and the shipping package is mailed prepaid or hand carried Shipping and handling charges will be applied for all orders that must be mailed when service is complete For faster service You can also request a RMA authorization online http Awww supermicro com This warranty only covers normal consumer use and does not cover damages in curred in shipping or from failure due to the alternation misuse abuse or improper maintenance of products During the warranty period contact your distributor first for any product problems SUPER AOC SGP i4 Add on Card User s Guide Conventions Used in the User s Guide Pay special attention to the following symbols for proper system installation and to prevent damage to the system or injury to yourself Warning Important information given to ensure proper system installation or to prevent damage to the components or injury to yourself Note Additional information given to differentiate between various models or provides information for correct system setup Naming Convention Character
13. ompiled make CFLAGS_EXTRA DIXGBE_NO_LRO install 5 Load the module For kernel 2 6 x use the modprobe command modprobe ixgbe lt parameter gt lt value gt For 2 6 kernels the insmod command can be used if the full path to the driver module is specified For example insmod lib modules lt KERNEL VERSION gt kernel drivers net ixgbe ixgbe ko 3 4 Chapter 3 Installation In addition when using 2 6 based kernels make sure that older ixgbe drivers are removed from the kernel before loading the new module To do this use rmmod ixgbe modprobe ixgbe 6 Assign an IP address to the interface by entering the following where x is the interface number ifconfig ethx lt IP_address gt netmask lt netmask gt 7 Verify that the interface works Enter the following where lt IP_address gt is the IP address for another machine on the same subnet as the interface that is being tested ping lt IP_address gt 3 5 SUPER AOC SGP i4 Add on Card User s Guide Notes 3 6 Disclaimer Continued The products sold by Supermicro are not intended for and will not be used in life support systems medical equipment nuclear facilities or systems aircraft aircraft devices aircraft emergency communication devices or other critical systems whose failure to perform be reasonably expected to result in significant injury or loss of life or catastrophic property damage Accordingly Supermicro disclaims any and all liabilit
14. ower supply the case the mounting fasteners and the add on card Unpacking The add on card is shipped in antistatic packaging to avoid static damage When unpacking your component or your system make sure that the person handling it is static protected ZA Note To avoid damaging your components and to ensure proper installa tion be sure to always connect the power cord last and always remove it before adding removing or changing any hardware components 3 1 SUPER AOC SGP i4 Add on Card User s Guide 3 2 Before Installation To install the add on card properly be sure to follow the instructions below 1 3 3 Power down the system Remove the power cord from the wall socket Use industry standard anti static equipment such as gloves or wrist strap and follow the instructions listed on Page 3 1 to avoid damage caused by ESD Familiarize yourself with the server motherboard and or chassis documenta tion Confirm that your operating system includes the latest updates and hotfixes Installing the Add on Card Follow the steps below to install the add on card into your system 1 Remove the server cover and if necessary set aside any screws for later use Remove the add on card slot cover If the case requires a screw place the screw aside for later use Position the add on card in the slot directly over the connector and gently push down on both sides of the card until it slides into the
15. the installation 3 5 Installing the Linux Operating System Follow the steps below to install the driver to a Linux system Build a Binary RPM Package 1 Run rpmbuild tb lt filename tar gz gt 2 Replace lt filename tar gz gt with the specific filename of the driver Note For the build to work properly the current running kernel MUST match the version and configuration of the installed kernel sources If you have just recompiled the kernel reboot the system at this time 3 3 SUPER AOC SGP i4 Add on Card User s Guide 3 6 Building the Driver Manually Follow the instructions below to build the driver manually 1 Move the base driver tar file to the directory of your choice For example home username ixgbe or usr local src ixgbe 2 Untar unzip archive tar zxf ixgbe x x x tar gz 3 Change to the driver src directory cd ixgbe x x x src 4 Compile the driver module make install The binary will be installed as lib modules KERNEL_VERSION kernel drivers net ixgbe ixgbe k o The install locations listed above are the default locations They might not be correct for certain Linux distributions For more information see the Idistrib txt file included in the driver tar Note IXGBE_NO_LRO is a compile time flag The user can enable it at 4 compile time to remove support for LRO from the driver The flag is used by adding CFLAGS_EXTRA DIXGBE_NO_LRO to the make file when it s being c
16. tive harm User s Guide Revision 1 0 Release Date April 10 2012 Unless you request and receive written permission from Super Micro Computer Inc you may not copy any part of this document Information in this document is subject to change without notice Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders Copyright 2012 by Super Micro Computer Inc All rights reserved Printed in the United States of America Preface Preface About this User s Guide This user s guide is written for system integrators PC technicians and knowledgeable PC users It provides information for the installation and use of the AOC SGP i4 add on card About this Add on Card With the AOC SGP i4 Supermicro has extended the boundaries of Ethernet tech nology to create the most compact and versatile 4 port Ethernet controller in the market allowing it to fit into the smallest spaces in a dense server system With an ultra small footprint and rich in power management features the AOC SGP i4 represents the next step in the evolution of gigabit Ethernet networking for enterprise and data center environments An Important Note to the User All images and layouts shown in this user s guide are based upon the latest PCB Revision available at the time of publishing The card you have received may or may not look exactly the same as the graphics shown in this user s
17. y and should buyer use or sell such products for use in such ultra hazardous applications it does so entirely at its own risk Furthermore buyer agrees to fully indemnify defend and hold Supermicro harmless for and against any and all claims demands actions litigation and proceedings of any kind arising out of or related to such ultra hazardous use or sale

Supermicro AOC-SGP-I4

Contents

Download Pdf Manuals

Related Search

Related Contents