Boss Audio Systems Chaos Exxstreme
Contents
1. CHAOS EXXTREME MOSFET Amplifier User s Manual page 11 Power and Speaker Wiring 2 Channel Amplifiers CX250 CX450 CX550 CX750 CX950 and CX1250 LEFT Speaker RIGHT a Speaker _ SPEAKER Two IMPEDANCE Channel 2 8 OHMS Mode POWER CONNECTIONS BATT REMOTE GROUND iPEAKER CONNE TIONS a Chassis ground point to REMOTE TURN ON terminal of head unit q 0 mo NE SPEAKER ubwooter IMPEDANCE 4 8 OHMS Bridged Mode POWER CONNECTIONS BATT REMOTE GROUND Chassis ground point Connect the Positive terminal of the subwoofer to the L amplifier terminal to REMOTE TURN ON terminal of head unit Connect the Negative terminal of the subwoofer to the R amplifier terminal CHAOS EXXTREME MOSFET Amplifier User s Manual page 12 Power and Speaker Wiring 2 Channel Amplifiers CX250 CX450 CX550 CX750 CX950 and CX1250 Tri mode operation allows you to connect this amplifier to a pair of main speakers plus a subwoofer on one pair of output channels The main speakers will operate in STEREO while the subwoofer simultaneously operates in MONO To set up the amplifier to run in this mode put the crossover switches in the FULL position Insert high pass filter capacitors and a low pass filter inductor into the wirin2. terminal of the RIGHT Subwoofer subwoofer to the CH1 amplifier terminal SPEAKER IMPEDANCE 2 8 OHMS RIGHT SPEAKER IMPEDANCE Subwoofer ASON Bridged POWER CONNECTIONS BATT GROUND REMOTE Chassis ground point to REMOTE TURN ON terminal of head unit Q O_O Connect the Negative terminal of the LEFT subwoofer to the CH4 amplifier terminal SPEAKER LEFT IMPEDANCE Subwoofer 4 8 OHMS Connect the Positive terminal of the LEFT subwoofer to the CH3 amplifier terminal CHAOS EXXTREME MOSFET Amplifier User s Manual page 17 Power and Speaker Wiring 5 Channel Amplifier CX1800 Tri mode operation allows you to connect this amplifier to a pair of main speakers plus a subwoofer on one pair of output channels The main speakers will operate in STEREO while the subwoofer simultaneously operates in MONO To set up the amplifier to run in this mode put the crossover switches in the FULL position Insert high pass filter capacitors and a low pass filter inductor into the wiring as shown below Be sure to check the table at the bottom of this page to determine the correct capacitor and inductor values for the crossover frequency you wish to achieve SPEAKER IMPEDANCE 8 OHMS Tri Mode __ Low pass RIGHT filter inductor XL Subwoofer Component values
3. Crossover range low pass high pass Bass boost Fuse rating Dimensions 11 7 8 x 2 5 8 x MODEL RMS POWER into 4 Ohms MAX POWER into 2 Ohms BRIDGED POWER into 4 Ohms Min speaker impedance THD Frequency response Signal to noise ratio Channel separation Damping factor Crossover range low pass high pass Bass boost Fuse rating Dimensions 11 7 8 x 2 5 8 x 2 Channel MOSFET Amplifiers CX250 CX450 CX550 TOW x2 110W x2 125W x2 200W X 2 300W X 2 400W X 2 400W X 1 600W x 1 800W x 1 2 Ohm Stereo 4 Ohm Mono Bridged 0 01 9Hz 50kHz 103dB 90dB 125 35Hz 160Hz fixed 200Hz Variable 0 18dB 20A 25A 25A 7 7 8 10 9 16 12 3 16 4 Channel MOSFET Amplifiers CX750 220W x 2 800W X 2 1600W x 1 15A x 2 14 7 8 5 Channel MOSFET Amplifier 30S AUDIO SYSTEMS CX950 CX1250 300W x 2 380W x 2 1000W X 2 1250W X 2 2000W x 1 2500W x 1 25A x2 60A 16 13 16 19 3 8 MonoBlock MOSFET Amplifiers CX600 CX650 CX800 CX1000 CX1800 CX1100M CX2000M 120W x4 250W x 1 TOW x 4 100Wx4 150Wx4 200W x4 200W x 1 200W X4 250W X4 400W X4 SOOWX4 300WX4 1100W X 1 400W X2 SOOWx2 800Wx2 1000W x2 600W x2 2 Ohm Stereo 4 Ohm Mono Bridged 0 01 QHz 50kHz 103dB 90dB 125 35Hz 160Hz fixed 200Hz Variable 0 18dB 20Ax2 20Ax2 13 3 8 15 5 8 25Ax2 80A 16 13 16 23 7 8 600W x 1 600W x 1 25AX3 20 n a 25A 10 11 16 SOOW x 1 2000W X
4. inputs If the hiss disappears at this point go on until the faulty noisy component is found It is best to set the amplifier s input level control as low as possible The best subjective signal to noise ratio is achieved in this manner Try to set the head unit as high as possible without distortion and the amp input level as low as possible Check for improperly grounded RCA interconnects Check that the Input Level Control is set to match the signal level of the head unit Always try to set the Input Level as low as possible Check that all crossover frequencies are properly set Check for short circuits on the speaker leads Check that the minimum speaker impedance for the amp model is correct Check that there is good air circulation around the amp In some applications it may be necessary to add external cooling fan s This is usually caused by poor quality RCA cables which can pick up radiated noise Use only the best quality cables and route them away from power cables Check that speaker leads are not shorted to the vehicle chassis Check that the RCA grounds are not shorted to the vehicle chassis Check that the head unit is properly grounded CHAOS EXXTREME MOSFET Amplifier User s Manual page 20 Specifications MODEL RMS POWER into 4 Ohms MAX POWER into 2 Ohms BRIDGED POWER into 4 Ohms Min speaker impedance THD Frequency response Signal to noise ratio Channel separation Damping factor
5. ow Pass J Oo D roohvav ev MIN MAX HIGH PASS m4cH r5cH O M A 6 Fads 3 Urow Pass FREQ 1daB Oi Fy CESSES MUU Lobatse REMOTE SUBWOOFER CH5 INPUTS CH5 CONTROLS D CONTROL LM wt G CH3 CH3 CH4 CH4 To Speaker Terminals of head unit CHAOS EXXTREME MOSFET Amplifier User s Manual page 10 High Level Input Wiring The high level input s should only be used when your head unit lacks RCA outputs If the RCA outputs are not present connect the speaker outputs from the receiver to the high level input connector of the amplifier Be sure to observe polarity to avoid audio phase problems NOTE Do not connect BOTH the high level and low level inputs from your receiver to your amplifier at the same time MonoBlock Amplifier CX1100M LOW PASS FREQUENCY SENSITIVITY 100 7 145 mO G 0 siab Hz no mV 2V CROSSOVER INPUT CONTROLS INPUTS EHAS MOSFET MONOBLOCK POWER AMPLIFIER POWER a L L R R To Speaker Terminals of head unit Remote MonoBlock Amplifier CX2000M LEFT RIGHT CROSSOV LEVEL D ra iow LEVEL INPUTS O PROTECTION REMOTE SUBWOOFER LEVEL CONTROL ERAS MOSFET MONOBLOCK POWER AMPLIFIER Remote Subwoofer Level Control L L R R To Speaker Terminals of head unit
6. quality RCA cable for best audio performance NOTE Do not connect BOTH the high level and low level inputs from your receiver to your amplifier at the same time MonoBlock Amplifier CX1100M Remote Subwoofer Level Control LOW PASS FREQUENCY MODE 100 7145 N lao one ee as D I oot L_l r k a 0 18dB FULL RANGE i 8V 100mV 2V LF amp Hz bo REMOTE SUBWOOFER BASS BOOST CROSSOVER LEVEL CONTROL To Audio Outputs of head unit or signal processor MonoBlock Amplifier CX2000M Remote Subwoofer Level Control Powe O I INPUT BASS CROSSOVER iam O PROTECTION A A EVEL BOOST FREQUENCY N soss oo OL a L HIGH LEVEL REMOTE SUBWOOFER LEVEL CONTROL To Audio Outputs of head unit or signal processor CHAOS EXXTREME MOSFET Amplifier User s Manual page 8 High Level Input Wiring The high level input s should only be used when your head unit lacks RCA outputs If the RCA outputs are not present connect the speaker outputs from the receiver to the high level input connector of the amplifier Be sure to observe polarity to avoid audio phase problems NOTE Do not connect BOTH the high level and low level inputs from your receiver to your amplifier at the same time 2 Channel Amplifiers CX250 CX450 CX550 CX750 CX950 and CX1250 Remote Subwo
7. 1 n a 25Ax2 16 13 16 All specifications subject to change without notice CHAOS EXXTREME MOSFET Amplifier User s Manual page 21 Notes Notes Z fobs AUDIO SYSTEMS Notes Z fobs AUDIO SYSTEMS
8. 30SS AUDIO SYSTEMS aaa MOSFET Car Audio mplifiers CX550 CX750 CX950 CX1250 CX600 Four Channel MOSFET Car Audio CX650 Amplifiers CX800 CX1000 Five Channel CX 1 800 MOSFET Car Audio Amplifier MonoBlock CX 1 1 00 M MOSFET Car Audio CX2000M Amplifier Congratulations on your purchase of a 3055 DIO SYSTEMS CHAOS EXXTREME Amplifier It has been designed engineered and manufactured to bring you the highest level of performance and quality and will afford you years of listening pleasure Thank you for making BUSS AUDIO SYSTEMS your choice for car audio entertainment page N OO OA Ah Ph WO WO N 15 16 17 18 19 20 21 USER S MANUAL CONTENTS Introduction What is included Features About 2 Ohm operation General precautions Installation precautions Mounting the amplifier Connecting the amplifier Low level input wiring High level input wiring 2CH Power and Speaker wiring 2CH and Bridged Modes 2CH Power and Speaker wiring TriMode 4CH Power and Speaker wiring 4CH and Bridged Modes 4CH Power and Speaker wiring TriMode 5CH Power and Speaker wiring 5CH Mode 5CH Power and Speaker wiring Bridged Mode 5CH Power and Speaker wiring TriMode MonoBlock Power and Speaker wiring Troubleshooting Specifications CHAOS EXXTREME MOSFET Amplifier User s Manual page 1 Introduction With the 399S CHAOS EXXTREME MOSFET amplifier series we are intr
9. ANGE GE CH1 2 CONTROLS j MOTE ire Sa l SUBWOOFER as GENA tet contro ou FOUR CHANNEL MOSFET POWER al To FRONT Audio Outputs of To REAR Audio Outputs of head unit or head unit or signal processor J CHAOS EXXTREME MOSFET Amplifier User s Manual page 6 signal processor Low Level Input Wiring Low level RCA input wiring is preferred for best audio performance Always use a high quality RCA cable for best audio performance NOTE Do not connect BOTH the high level and low level inputs from your receiver to your amplifier at the same time 5 Channel Amplifier CX1800 Remote Subwoofer Level Control n C cO NTROLS kenaa m SVY LEVE NODE Heo ASS FREQ fil re SENSITIVITY LEVEL FUL S mo Paro METS d On TAM 90 vav bev MIN max lF A EN 45 EELO ye 1S EI ox An 9 A db O Protect PASS INPUT MODE CENT RAV LEVEL vo 4 KEMA E REMOTE SUBWOOFER D CH5 CH5 CONTROLS LEVEL CONTROL 3 4 CONTROLS f Sib a To SUBWOOFER Audio Outputs of head unit or signal processor if present To FRONT Audio To REAR Audio Outputs of head Outputs of head unit or signal unit or signal processor processor CCCoCICoco CHAOS EXXTREME MOSFET Amplifier User s Manual page 7 Low Level Input Wiring Low level RCA input wiring is preferred for best audio performance Always use a high
10. Speaker 80 Hz 7 5mH 470uF MINIMUM 100 Hz 6 5mH 330uF High pass filter SPEAKER 120 Hz 5 5mH 330uF crossover IMPEDANCE 150 Hz 4mH 220uF 4 OHMS CH4 Speaker Low pass 8 filter inductor POWER CONNECTIONS BATT REMOTE GROUND EE ___ Chassis ground point High pass filter crossover to REMOTE TURN ON terminal of head unit ea CH2 Speaker MINIMUM SPEAKER IMPEDANCE 4 OHMS High pass filter crossover CH1 Low pass filter inductor SPEAKER nee Subwoofer IMPEDANCE 8 OHMS CHAOS EXXTREME MOSFET Amplifier User s Manual page 15 Power and Speaker Wiring 5 Channel Amplifier CX1800 Five Channel Mode CH5 Subwoofer CH1 CA Speaker x 7 SPEAKER SPEAKER i CH2 IMPEDANCE IMPEDANCE Speaker 2 8 OHMS 2 8 OHMS 1 2 BRIDGE Dm Zun GROUND REMOTE BATT POWER CONNECTIONS _ d SPEAKER IMPEDANCE 2 8 OHMS CH3 Speaker J pi CH4 Speaker CHAOS EXXTREME MOSFET Amplifier User s Manual page 16 Chassis ground point to REMOTE TURN ON terminal of head unit q a 9 Power and Speaker Wiring 5 Channel Amplifier CX1800 Connect the Negative terminal of the RIGHT subwoofer to the CH2 amplifier terminal CHS Connect the Positive
11. anual Please keep this manual in a safe place for future reference e Do not open or attempt to repair this unit yourself Dangerous high voltages are present which may result in electric shock Refer any repairs to a qualified service technician e To avoid risk of electronic shock or damage to the amplifier do not permit any of this equipment to become damp or wet from water or drinks If this does occur immediately unplug the power wires and send the amplifier to your local dealer or service center as soon as possible e f there is smoke or any peculiar odor present during use or if there is damage to any of the component enclosures immediately unplug the power wire and send the amplifier to your local dealer or service center as soon as possible Installation precautions Before you drill or cut any holes investigate your car s layout very carefully Take special care when you work near the gas tank fuel lines hydraulic lines and electrical wiring Never operate the amplifier when it is unmounted Attach all audio system components securely to prevent damage especially in an accident CHAOS EXXTREME MOSFET Amplifier User s Manual page 4 Before making or breaking power connections in your system disconnect the vehicle battery Confirm that your head unit or other equipment is turned off while connecting the input jacks and speaker terminals If you need to replace the power fuse replace it only wit
12. ed Power Supply e 2 Ohm stable stereo operation with output power increase e Thermal and speaker short protection e Soft turn on circuit e Remote turn on turn off circuit e Variable input gain control e Variable low pass crossover s e Fixed high pass crossover s e Variable 0 to 18dB Bass Boost e Nickel plated RCA low level and high level inputs e LED power and protection indicators e Silver anodized heatsink e Remote subwoofer level control About 2 Ohm operation Your CHAOS EXXTREME amplifier has been designed to operate efficiently at loads down to 2 Ohms This means that you can install four 8 Ohm speakers per channel when using parallel wiring Increasing the number of woofers per channel at low frequencies below 100Hz produces an acoustic coupling effect This acoustic coupling effect increases your power output by about 3dB per speaker or the equivalent of an additional 10W per speaker When operating at 2 Ohms the amplifiers will increase their output power by approximately 50 The current draw will also increase by about the same amount so be sure you have enough current to run the amplifiers into a 2 Ohm load If you lack adequate current your music reproduction will be distorted CHAOS EXXTREME MOSFET Amplifier User s Manual page 3 General precautions Before installing and using your new 3095 amplifier please be come familiar with all the infor mation contained in this m
13. ems SYMPTOM Amplifier will not power up Protection LED comes on when amplifier is powered up Low output Audio present in only one channel High hiss in the speakers Squealing noise from speakers Distorted sound Amplifier gets very hot Engine noise static type Engine noise alternator whine POSSIBLE REMEDY Check to make sure you have a good ground connection Check that the Remote Input Turn On has at least 3VDC Check that there is battery power on the terminal Check that there is at least 12v Check all fuses replace if necessary Make sure that the Protection LED is not illuminated If it is lit shut off the amplifier briefly and then repower it Check for short circuits on speaker leads Turn down the volume control on the head unit to prevent overdriving Remove speaker leads and reset the amplifier If the Protection LED still comes on then the amplifier is faulty and needs servicing Check that all fuses are OK Check that amplifier is properly grounded Check that the Remote Input Turn On has at least 3VDC Check that the RCA audio cables are plugged into the proper inputs Check all speaker wiring Reset the Level Control Check the Crossover Control settings Check the RCA interconnect cables Check all speaker wiring Disconnect all RCA inputs to the amplifiers If the hiss disappears then plug in the component driving the amplifier and unplug its
14. for amp 6dB Passive Crossover High pass filter FREQUENCY INDUCTOR CAPACITOR crossover Ear CH1 ea a ake i Speaker 80 Hz 7 5mH 470uF 100 Hz 6 5mH 330uF oinaestii 5 1 2 Li ul M 120 Hz 5 5mH 330uF crossover IMPEDANCE 150 Hz 4mH 220uF A GHG CH5 CH2 Subwoofer Speaker SPEAKER IMPEDANCE 2 8 OHMS amp fe I N FUSES POWER en GROUND REMOTE _BATT PG fall WIG a I ag to REMOTE TURN ON terminal of head unit High pass filter crossover d E O o High pass filter crossover MINIMUM SPEAKER IMPEDANCE 4 OHMS SPEAKER IMPEDANCE 8 OHMS Low pass filter inductor Subwoofer CHAOS EXXTREME MOSFET Amplifier User s Manual page 18 Power and Speaker Wiring Monoblock Amplifiers CX1100M and CX2000M Speaker SPEAKER IMPEDANCE MonoBlock 2 8 OHMS Mode POWER CONNECTIONS BATT REMOTE GROUND Chassis Z ground point to REMOTE TURN ON terminal of head unit Cl CHAOS EXXTREME MOSFET Amplifier User s Manual page 19 Troubleshooting If you experience operation or performance problems with this product compare your installation with the electrical wiring diagram on the previous pages If problems persist read the following troubleshooting tips which may help eliminate the probl
15. g as shown below Be sure to check the table at the bottom of this page to determine the correct Capacitor and inductor values for the crossover frequency you wish to achieve Component values for 6dB Passive Crossover FREQUENCY INDUCTOR CAPACITOR 80 Hz 7 5MH 470uF 100 Hz 6 5mH 330uUF 120 Hz 5 5mH 330uF 150 Hz 4mH 220uF Tri Mode POWER CONNECTIONS BATT REMOTE GROUND S 9 CP FUSE Chassis ground point High pass filter crossover to REMOTE TURN ON terminal of head unit Q z n m S Cd SPEAKER High pass filter IMPEDANCE crossover 4 OHMS Speaker SPEAKER Low pass IMPEDANCE filter inductor 8 OHMS Subwoofer CHAOS EXXTREME MOSFET Amplifier User s Manual page 13 Power and Speaker Wiring 4 Channel Amplifiers CX600 CX650 CX800 and CX1000 CH2 Speaker p CH1 Speaker Four Channel Mode BATT REMOTE GROUND ___ Chassis ce ground SPEAKER an point peaker E SON to REMOTE TURN ON l CH4 terminal of head unit O Speaker J o SPEAKER IMPEDANCE 2 8 OHMS a SPEAKER IMPEDANCE 4 8 OHMS Connect the Negative terminal of the RIGHT subwoofer to RIGHT the CH2 amplifier terminal Subwoofer Connect the Positive terminal of the RIGHT subwoofer to
16. h Use 8 gauge or heavier wire 2 Connect the remote terminal to the remote output of the head unit using 16 gauge or heavier wire 3 Connect an empty fuse holder within 18 45 cm of the car battery and run 8 gauge or heavier cable from this fuse to the amplifier location 4 Check that the fuse holder is empty Then connect the fuse holder to the BATT connection on the amplifier 5 If multiple amplifiers are being used in your system either e Run a separate pair of cables from the battery and a chassis ground point to each amplifier Each cable must have its own inline fuse or e Run a 4 cable from the fuse holder at the battery to a distribution block at or near the amplifiers location Then run separate cables from the amplifier to this distribution block and to independent chassis ground points 6 Connect all line inputs and outputs if used using high quality cables Connect all speakers following the diagrams in this manual Be sure to observe proper polarity to avoid audio phase problems 7 Insert fuse s into the battery fuse holder s 8 Recheck all connections before powering up the amplifier 9 Set all level controls to minimum position and set all crossover controls switches to the desired frequency points 10 Power up the head unit and the amplifier Then set the volume control on the head unit to about 3 4 volume and adjust the amplifier s input level control s to
17. h a fuse identical to that supplied with the amplifier Using a fuse of a different type or rating may result in damage to your audio system or your amplifier which is not covered by the manufacturer s warranty Mounting the amplifier 1 Find a suitable location in the vehicle in which to mount the amplifier 2 Make sure there is sufficient air circulation around the intended mounting location 3 Mark the location for the mounting hole screws by positioning the amplifier where you wish to install it Use a scribe or mounting screw inserted through each of the amp s mounting holes to mark the mounting surface If the mounting surface is carpeted measure the hole centers and mark with a felt tip pen 4 Drill pilot holes in the mounting surface for the mounting screws Place the amplifier in position and attach the amplifier to the mounting surface securely using screws SHOCK HAZARD Do not open the case of this product There are dangerous voltages present within the unit There are no user serviceable parts within the unit Connecting the amplifier Before doing any wiring look through this manual and identify the diagrams to follow for power input and speaker connections for your particular installation Be sure you understand all the connections before you proceed 1 Connect the power ground terminal to the closest point on the chassis of the car Keep this ground wire to less than 39 100 cm in lengt
18. just below the level of distortion 11 Further fine tuning of the various controls may be necessary to obtain best results Don t misuse the level control Do not mistake the input level control for a volume control It is designed ONLY to match the output level of your audio source to the input level of your amplifier Do not adjust this input level to maximum unless your input level requires it Ignoring these instructions will result in an input overload to the amplifier and excessive audio distortion It can also cause the protection circuit to engage CHAOS EXXTREME MOSFET Amplifier User s Manual page 5 Low Level Input Wiring Low level RCA input wiring is preferred for best audio performance Always use a high quality RCA cable for best audio performance NOTE Do not connect BOTH the high level and low level inputs from your receiver to your amplifier at the same time 2 Channel Amplifiers Remote Subwooler Level Control CX250 CX450 CX550 eS CX750 CX950 and CX1250 HT power O Lz LEVEL BOOST SO Boss Ea O O70 HIGH LEVEL tow w LA Hz MO CROSSOVER o 2 ANNEL MOSFET POWER AMPLIFIER To Audio Outputs of head unit or signal processor 4 Channel Amplifiers CX600 CX650 CX800 and CX1000 TO Remote Subwoofer Level Control mate PROTECTION HIGH PASS FULL R
19. oducing eleven new amplifiers all designed in the USA This new series includes a two monoblock amps six 2 channel four 4 channel amplifiers and a 5 channel amp All CHAOS EXXTREME models feature variable low pass and high pass crossovers and variable input gain controls They also incorporate an input voltage sensistivity selector for added system flexibility For further flexibility in the use of a subwoofer 0 18dB Bass Boost control has been included on all amplifiers You can control the subwoofer level with the remote level control module 3098 understands that amplifiers are placed in many different kinds of installations So we incorporated a very flexible system of controls in these amplifiers in order to help you integrate the amp into your system regardless of the nature of your input source CHAOS EXXTREME MOSFET Amplifier User s Manual page 2 What is included When first unpacking your new amplifier please check first that the package contains all of the items below If something is missing contact the store where you purchased the amplifier e CHAOS EXXTREME amplifier e Remote subwoofer level control eHigh input cable with connector e Four 4 mounting screws Features Your new CHAOS EXXTREME amplifier features the following e Class A B operation e Bridgeable outputs except CX1100M and CX2000M e Tri Mode capable except CX1100M and CX2000M e MOSFET PWM Pulse Width Modulat
20. ofer Level Control LEFT RIGHT LEVEL G DNTROL fl j LEVEL BOOST BO ig Fa O ORRO o g LOW LEVEL LOW PASS FREQ Hz MODE INPUTS CROSSOVER EHAS O gt Gorn TWO CHANNEL MOSFET POWER AMPLIFIER L L R R To Speaker Terminals of head unit Remote Subwoofer Level Control 4 Channel Amplifiers CX600 CX650 CX800 and CX1000 Boss m CROSSOVER LOW PASS INPUT INPUT BASS LOW PASS POWER O E FREQ D VEL ij To Speaker Terminals of head unit CH CH CH CH T 1 1 2 2 CH CH CH CH T a ee OOo CHAOS EXXTREME MOSFET Amplifier User s Manual page 9 High Level Input Wiring The high level input s should only be used when your head unit lacks RCA outputs If the RCA outputs are not present connect the speaker outputs from the receiver to the high level input connector of the amplifier Be sure to observe polarity to avoid audio phase problems NOTE Do not connect BOTH the high level and low level inputs from your receiver to your amplifier at the same time 5 Channel Amplifier CxX1800 Remote Subwoofer Level Control CH1 CH1 CH2 CH2 OL m To Speaker Terminals of head unit CH1 2 CONTROLS INPUT CONTROLS e R iia INPUT CONTROLS _ SENSITIVITY LEVEL MODE ee 0 EEG D SENSITIVITY LEVEL FULI 10w pass v 2 28v Mak
21. the CH1 amplifier terminal poe m russ SPEAKER CONNECTIONS ol TENNIE l C COD 6cH3 Sco BATT REMOTE GROUND e1 D Chassis ground point LEFT Subwoofer to REMOTE TURN ON i terminal of h it Connect the Negative erminal of head uni terminal of the LEFT SPEAKER IMPEDANCE subwoofer to the CH4 m M 4 8 OHMS amplifier terminal FUSE Connect the Positive terminal of the LEFT subwoofer to the CH3 amplifier terminal CHAOS EXXTREME MOSFET Amplifier User s Manual page 14 Power and Speaker Wiring 4 Channel Amplifiers CX600 CX650 CX800 and CX1000 Tri mode operation allows you to connect this amplifier to a pair of main speakers plus a subwoofer on one pair of output channels The main speakers will operate in STEREO while the subwoofer simultaneously operates in MONO To set up the amplifier to run in this mode put the crossover switches in the FULL position Insert high pass filter capacitors and a low pass filter inductor into the wiring as shown below Be sure to check the table at the bottom of this page to determine the correct capacitor and inductor values for the crossover frequency you wish to achieve SPEAKER IMPEDANCE 8 OHMS Tri Mode RIGHT Subwoofer Component values for 6dB Passive Crossover ap filter o H3 FREQUENCY INDUCTOR CAPACITOR i
Download Pdf Manuals
Related Search