Mobotix MX-OPT-GPS1-EXT
Contents
1. Z MX GPS Box Quick Install Ji A The HiRes Video Company MOBOTIX Weatherproof GPS Time and Position Information o e MX GPS Box 3 4 Protection ae TA ere oman a So 3 O Ox sa amp a e GPS time base for MOBOTIX cameras with MxBus e New camera alarms available position speed illumination temperature Reliable GPS time base for MOBOTIX systems includes outdoor temperature and illumination sensors connects via 2 wire cable e Remote installation max 50 m 55 yd wire length e Complete set including mounting supplies Connecting the MX GPS Box MOBOTIX MX GPS Box MOBOTIX IP Video Door Station T24 MX OPT GPS1 EXT MX T24M Sec D1 Illumination Temperature sensor sensor 2 wire MxBus wiring to camera max 50 m 55 yd MOBOTIX Camera Installation Instructions 1 Find a suitable mounting position To guarantee optimum reception of the GPS signals by the MX GPS Box you should find a spot on the outside of a building which provides a clear view of the sky max 50 m 55 yd wire length between the MOBOTIX camera and the MX GPS Box 2 Attach the box oE Attach the MX GPS Box at the mounting position with the cable ports pointing downwards Next remove the box 2 MX GPS Box cover three screws Do not remove the white sealing plug left or the temperature sensor center 3 Prepare the MxBus wires Before proceeding make sure there is no voltage on2. If the MX GPS Box had been connected to a different camera before the left LED MxBus status is blinking red after establishing the MxBus connection In this case you need to reset the connected and activated MX GPS Box to factory defaults e Remove the box cover three screws i P x MS x e Bridge the contact surfaces below the Factory Reset label red circle in figure A A EE using a screw driver for example both LEDs are flashing red blue with increasing MOBOTIX frequency CE FE x Factory e Only remove the bridge if both LEDs of the MX GPS Box are flashing green on off 3 times to indicate that the process has finished successfully e Mount the cover back onto the box torque 0 4 Nm e Set up the MX GPS Box in the camera see Manually Initializing the MX GPS Box above Notes The MOBOTIX MX GPS Box is to be used only for providing sensor data GPS position velocity temperature illumination for MOBOTIX cameras in IP65 environments For MOBOTIX cameras with MxBus connector and software version MX V4 1 1 21 or higher Additional events not available on MOBOTIX Web and Basic camera models The GPS data s precision changes due to external factors e g number of currently received satellites weather Make sure that you adhere to all relevant laws regulations and that you fulfill all certification requirements for the intended use Torque for all box cover screws 0 4 Nm When using the cable plug for
3. the MxBus wiring eight wire plug or cable plug 3 to 5 mm or 5 to 7 mm right make sure that you press the plug into the casing in such a way that the rims stick out equally on both sides J Copyright MOBOTIX AG 2012 Made in Germany Technical information subject to change without notice The length of the entire MxBus wiring must not exceed 50 m 55 yd Diameter of the MxBus wires 0 6 to 0 8 mm 0 8 mm are recommended to avoid line losses HiRes Video Innovations The German company MOBOTIX AG is known as the leading pioneer in network camera technology and its decentralized concept has made high resolution video systems cost efficient S x T O 2 e E 3 S S MOBOTIX AG D 67722 Langmeil Tel 49 6302 9816 103 Fax 49 6302 9816 190 sales mobotix com
4. General Tasks gt Reboot e Wait for at least 5 minutes after rebooting then open the Admin Menu gt Camera Administration gt Time and Date dialog and check the Local NTP Service section You should now see the GPS entry in the refid column e Enter the IP address of this camera as NTP time server in the corresponding dialog for all other cameras 5 Set up additional events for GPS position GPS velocity temperature and illumination Using these events the connected MOBOTIX camera can trigger an alarm if it leaves or reaches the defined position exceeds or goes below the defined speed or if the sensors detect changes in temperature or illumination not available for Web and Basic models e In the Live screen of the camera click on Setup Menu gt Event Control gt Event Overview e Click on the Edit button in the Environment Events section e Click on Add new profile at the bottom of the dialog select the desired Event Sensor Type and enter a new name for the profile e g GP for GPS Position GT for Temperature at the MX GPS Box When defining new temperature or illumination events you also need to set the Sensor Source to GPS Box e Set the parameters of the selected sensor as required e g use the current position as Anchor Position by clicking on the Set to Current Position button e Continue to define the other events you need by creating individual profiles with descriptive names click on to see the help topic f
5. e found automatically when using the Autoconfiguration feature In the process the entire system will be set to use the box as time server see T24MX IP Video Door Station System Manual Part 2 on www mobotix com HiRes Video Innovations The German company MOBOTIX AG is known as the leading pioneer in network camera technology and its decentralized concept has made high resolution video systems cost efficient S as Ko e E z S MOBOTIX AG D 67722 Langmeil Tel 49 6302 9816 103 Fax 49 6302 9816 190 sales mobotix com 2 MX GPS Box Quick Install A The HiRes Video Company MOBOTIX LED Signaling MxBus Status GPS Signal i e LED Meaning MxBus not connected MxBus Status Regular operation MX GPS Box e O O LED is off GPS Signal O LED is on permanently right LED flashes at regular intervals amp Ge LED is on with short interruptions 1 6 sec Unencrypted communication No bus communication e g invalid encryption No GPS data available Only time data available 2D position data available oge92e2 00 Full 3D position data available Manually Initializing the MX GPS Box 1 Open the MOBOTIX camera s user interface in the browser e Enter the IP address of the camera that is connected to the MX GPS Box in the browser admin access rights required http lt camera IP address gt e Click on the Admin Menu bu
6. or this dialog e Click on Set then on Close and permanently store the configuration Note on Using GPS Position as Event When using GPS Position as environment event you need to consider the precision of the GPS data The precision also changes due to external factors e g number of currently received satellites weather You should thus set a value for Distance that is large enough to avoid false alarms In order to get a suitable value click on D inthe top right corner of the browser and determine the precision in the Sensors gt GPS Position section of the Camera Status dialog 6 Define actions for the additional events e In the Live screen of the camera click on Setup Menu gt Event Control gt Action Group Overview e Click on the Add new group button at the bottom of the dialog e Enter a descriptive name for the group then click on the Edit button in this line e Highlight the corresponding events in the Event Selection list and add the desired actions by clicking on Add new action see help topic for this dialog by clicking on e Click on Set then on Close and permanently store the configuration 7 Store the camera configuration e In the Live screen of the camera click on Admin Menu gt Configuration gt Store and permanently store the camera configuration without rebooting e Save the camera configuration to the local computer Admin Menu gt Configuration gt Save Resetting the MX GPS Box
7. the MxBus wires Cut the MxBus cable to size 2 wire 0 6 to 0 8 mm diameter When using wires without sheath strip the insulation of the wires for 5 mm and push the wires through the eight wire plug right When using a cable with sheath remove the pre installed eight wire plug and insert the appropriate cable plug 3 to 5 mm or 5 to 7 mm Press the rubber plug into the casing in such a way that the rims stick out equally on both sides Push the cable through the plug remove the sheath on a length of 15 mm and strip the insulation of the wires for about 5 mm 4 Connect the MxBus wires to the terminal Connect the MxBus wires to the screw terminals using the screwdriver Make sure to maintain the polarity see sticker in front of the terminal Mount the cover back onto the box torque 0 4 Nm 5 Connect the MxBus wires to the opposite side Connect the MxBus wires as described in the corresponding manual to the MOBOTIX camera or to another MxBus module connected to a camera e g Keypad Security Door Opener Make sure not to exceed the overall length of the MxBus wiring of 50 m 55 yd MxBus connector of MOBOTIX D14 Drilling Template for the MX GPS Box MX GPS Box www mobotix com gt Support gt Manuals Drilling templates for other MOBOTIX components Initial Operation of a New IP Video Door Station T24 When installing a new MOBOTIX IP Video Door Station T24 for the first time the MX GPS Box will b
8. tton in the Live screen of the camera 2 Activate the MxBus interface e In the Hardware Configuration section click on Manage MxBus Modules e If you have not yet done so activate the MxBus Interface in the Manage MxBus Modules dialog Click on the Connect button in the MxBus Interface section After about 15 to 20 seconds the status changes to New device s available the Device Type shows GPS Module with the status Addressable in the Devices section 3 Activate MX GPS Box as MxBus module e In the Manage MxBus Modules dialog Devices section GPS Module line click on the Activate button After about 10 to 15 seconds the status changes to Active and the status LED of the MX GPS Box left is solid green 4 Set the MX GPS Box as time base The MX GPS Box can be used as GPS time base for the entire MOBOTIX system thus providing accurate time for synchronizing the system C FC 2012 Declaration of Conformity www mobotix com gt Support gt Media Library gt Certificates e Inthe Live screen of the camera click on Admin Menu gt Camera Administration gt Time and Date e Make sure that Time Server Protocol has been set to NTP e Enter 127 127 1 0 in an empty field in the Time Settings gt Time Servers section Do not remove the other NTP servers since they increase the redundancy provided they can be reached e Click on Set then on Close and permanently store the configuration e Reboot the camera Admin Menu gt
Download Pdf Manuals
Related Search