Adtran XFP 10G 1550nm
Contents
1. 2 The XFP is NRTL listed and CB Certified to all applicable American and European safety standards For continued compliance with the above laser safety standards only approved Class 1 modules from our approved vendor list located on the ADTRAN website should be installed in ADTRAN products NOTE The Gigabit Ethernet port s are optical and therefore are not classified as any type of port as defined in Appendix B of GR 1089 CORE Issue 5 The XFP is designed to meet the following environmental classes ETSI EN 300 019 1 1 Classification of environmental conditions Storage Class 1 2 ETSI EN 300 019 1 2 Classification of environmental conditions Transportation Class 2 3 ETSI EN 300 019 1 3 Classification of environmental conditions Stationary use at weather protected locations Class 3 3 The equipment is designed to function without degra dation during exposure to all test severities per Class 3 3 of ETSI EN 300 019 1 3 The XFP meets EU RoHS Directive 2002 95 EC and or applicable exemptions Refer to www adtran com for further information on RoHS WEEE ADTRAN CUSTOMER CARE From within the U S 1 800 726 8663 From outside the U S 1 256 963 8716 PRICING AND AVAILABILITY 1 800 827 0807 61442940G1C 22Ax hs SUBJECT TO ELECTROSTATIC DAMAGE OR DECREASE IN RELIABILITY HANDLING PRECAUTIONS REQUIRED2. www adtran com ADRAN PROVISIONING The XFP is not directly provisionable To provision the XFP access the menu system of the host module Refer to the Provisioning section of the Job Aid or Installation and Maintenance Practice provided with the host module for provisioning details SAFETY AND REGULATORY COMPLIANCE Electrostatic Discharge ESD can damage electronic modules When handling modules wear an antistatic discharge wrist strap to prevent damage to electronic components Place modules in antistatic packing material when transporting or storing When working on modules always place them on an approved antistatic mat that is electrically grounded The XFP meets or exceeds all the applicable requirements of NEBS Telcordia GR 63 CORE and GR 1089 CORE The XFP is intended for deployment in Central Office type facilities EEEs EECs and locations where the NEC applies for example Customer Premises The XFP is to be installed in ADTRAN products in Restricted Access Locations only and installed by trained service personnel This device complies with FCC 47 CFR Part 15 Class B Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Changes or modifications not expressly approved by ADTRAN could void the user s authority to operate this equi
3. ADRAN Small Form Factor Pluggable jobAid fy 10 Gigabit Ethernet XFP 1550 nm 07 E UN Product P N 1442940G1C Commercial Temperature DESCRIPTION The 10 Gigabit Ethernet XFP 1550 nm Commercial Temperature XFP optical transceiver is a full duplex serial electric serial optical device with both transmit and receive functions contained in a single module The XFP provides a high speed serial link at 10 Gb s Installed into an appro priate host module the XFP provides a 10 Gigabit interface to the supporting system The transmit side of the XFP converts serial NRZ electrical date at the10 Gb s line rate to a standard compliant optical signal The receive side of the XFP converts the incoming DC balanced serial NRZ optical data at the 10 Gb s line rate into serial electrical data NOTE To ensure compatibility refer to the documentation provided with the host module The following features are supported on the XFP 1550 nm optical signals for up to 40 km reach Case commercial temperature range from 0 C to 70 C Low power consumption lt 3 W max Excellent EMI performance Due to compliance certification requirements only XFPs supplied by ADTRAN are to be used with the host module ADTRAN cannot certify system integrity with other XFPs Issue Date November 2010 Document P N 61442940G1C 22A Operational Specifications Optical Specifications Transmit Wavelength 1550 nm Receive W
4. avelength 1530 to 1565 nm Data rate 9 95 Gb s to 11 3 Gb s Optical transmit level 1 to 2 dBm Optical receive level gt 16 dBm Optical distance 40 km maximum Optical connectors LC Extended Environmental Support Operational temperature range 0 C to 70 C Storage temperature range 40 C to 85 C Relative humidity to 85 noncondensing INSTALLATION Inspect the XFP If damaged file a claim with the carrier and then contact ADTRAN Customer Service To install the XFP into an appropriate module complete the following steps 1 Insert the XFP into the XFP cage on the circuit board of the host module with the latch handle facing out ward Slide the XFP all the way into the receptacle NOTE The latch on the XFP is for removal only When removing the XFP rotate the latch away from the XFP cage until a physical click occurs The XFP should slide easily out of the cage 2 Using thumb and forefinger exert adequate pressure to ensure the XFP is completely seated in the XFP cage 3 Do not remove the connector plug until the optical fiber connection is made NOTICE It is recommended that the connector plug remain on whenever the transceiver optical fiber connector is not inserted 4 Continue the installation and turn up of the host module using the instructions in the Job Aid provided with that module or using the Installation and Maintenance Practice I amp M available online at
5. pment A CAUTION Per GR 1089 CORE the ADTRAN system in which the SFP is being deployed is designed and intended for installation as part of a Common Bonding Network CBN The ADTRAN system in which the SFP is being deployed is not designed nor intended for installation as part of an Isolated Bonding Network IBN Per GR 1089 CORE Section 9 the XFP does not have an internal DC connection between battery return and frame ground The XFP can be installed in a DC I isolated or DC C common configuration For installations where other cards or the host system have internal connections between battery return and frame For more information refer to the Installation and Maintenance Practice P N 61442940G1C 5 available online at www adtran com Warranty ADTRAN will replace or repair this product within the warranty period if it does not meet its published specifications or fails while in service Warranty information can be found online at www adtran com warranty 2010 ADTRAN Inc All Rights Reserved ground the system would be intended for deployment only ina DC C configuration The ADTRAN system chassis frame ground terminal must be connected to a reliable earth ground to ensure that the metal enclosure of the XFP is properly grounded via the backplane connector A CAUTION The XFP is a Class 1 Laser Product and complies with the Laser Safety requirements of FDA 21CFR 1040 10 and 1040 11 and IEC60825 1 and
Download Pdf Manuals
Related Search