Datamax O'Neil 210216-000 mounting kit
Contents
1. swivel lock base by pulling the bumpers down toward you Figure 4 Figure 4 Charger Swivel Lock 210216 001 Use the Charger Swivel Lock bracket with printers that are equipped with two charging contact points located on the back of the printer s case When a printer is attached to the Charger Swivel Lock bracket the printer s batteries are automatically charged Locking Lever Swivel Lock Base 3 Mounting Holes Swivel Lock Head 2 Charging points Figure 5 Parts List 1 Charger Swivel Lock 3 10 pan head screws not included screw length to be determined by user Selecting a Location General Guidelines e If you are using the charger swivel lock do not short contacts e Use only an Datamax O Neil approved power supply e If you are using the charger swivel lock do not allow the charging points to come in contact with metal objects e Position the bracket and or printer with enough room to properly open and close the printer e Position the bracket and or printer so it is protected from environmental elements such as moisture tools and boxes e Position the bracket and or printer in a secure area in normal traffic patterns e Do not position the bracket above near or relative to the driver s position as to interfere with normal driving operations e Mount the bracket and or printer away from the driver s head to eliminate potential injury in the event of an accident e Hole ce2. Standard Swivel Lock 210216 000 Use the Standard Swivel Lock bracket for the 2t and 4t printers all makes and models Locking Lever Swivel Lock Base 3 Mounting Holes Swivel Lock Head Figure 1 Parts List 1 Standard Swivel Lock 3 10 pan head screws not included screw length to be determined by user SlimCard Reader Swivel Lock 210217 000 Use the SlimCard Reader Swivel Lock bracket for 2t and 4t SlimCard Reader printers manufactured after 01 01 2004 all makes and models Locking Lever Swivel Lock Base 3 Mounting Holes Swivel Lock Head 2 Bumpers Figure 2 Parts List 1 SlimCard Reader Swivel Lock 3 10 pan head screws not included screw length to be determined by user 2 Bumpers pre installed SlimCard Reader Retrofit Swivel Lock 210222 000 Use the SlimCard Reader Retrofit Swivel Lock bracket for 2t and 4t SlimCard Reader printers manufactured before 01 01 2004 Locking Lever Swivel Lock Base 3 Mounting Holes Swivel Lock Head 2 Bumpers Figure 3 Parts List 1 SlimCard Reader Retrofit Swivel Lock 3 10 pan head screws not included screw length to be determined by user 2 Bumpers pre installed Removing the Bumpers If you are using the 4t SlimCard Reader printer you must remove the bumpers from the swivel lock base Use the following procedure to remove the bumpers from the swivel lock base 1 Remove the bumpers from the
3. nters Left to right 2 324 Up and down 1 162 on center e Only use 10 pan head screws for mounting e Datamax O Neil does not accept liability for improperly mounted or poorly placed swivel locks and or printers Step 1 Mounting the Swivel Lock 1 Use the swivel lock base as a template to mark the three mounting holes on the mounting surface For guidelines on mounting and or installation see Selecting a Location 2 Drill the mounting holes at the marked locations 3 Attach the bracket to the mounting surface using 10 pan head screws Thread the screws through the swivel lock and mounting holes Figure 6 Figure 6 4 Tighten securely 5 If needed use additional mounting hardware to secure the bracket to the mounting surface 6 Proceed to Attaching the Printer or if you mounted a charger swivel lock proceed to Connecting the Power Supply Step 1a Connecting the Power Supply Optional Perform the following procedure only if you mounted a charger swivel lock bracket P N 210216 001 Warning Use only the equipment and parts specified in this instruction sheet Datamax O Neil does not accept liability for improperly connected swivel locks and or printers 1 Mount the charger swivel lock bracket For more information see Mounting the Swivel Lock in the previous section 2 Connect the power supply as follows a Vehicle Mounted Printers f you mounted your Charger swivel lock bracket
4. r OEMs 90 days from the date of purchase Batteries cables power supplies and other accessories will be warranted for ninety 90 days Datamax O Neil makes no other warranties expressed or implied including implied warranties of merchantability and fitness of purpose If you try to repair disassemble or change the product in any way or use parts not provided by Datamax O Neil without prior written authorization all warranties are void For complete warranty and service information see the Warranty Card included in your printer s original packaging No Liability for Negligent Use In no event shall Datamax O Neil be held liable for any damages whatsoever including without limitations damages for loss of profits business interruption loss of information or other pecuniary loss arising out of negligence in use and care of the product COPYRIGHT 2010 DATAMAX O NEIL 110119 005 Swivel Lock Brackets Instruction Sheet do datamax o neil right by our customers
5. to a vehicle connect your vehicle s cigarette adapter plug to the swivel lock charger s socket Figure 7 b Stationary Mounted Printers If you mounted your charger swivel lock bracket to a stationary surface connect your wall adapter s plug to the swivel lock charger s socket Figure 7 Note The cigarette adapter must have a 5 amp fuse and be Datamax O Neil approved The wall adapter s voltage cannot exceed 1 5 amps 1 amp recommended 2 Charging contact points Charger s socket 5 5 mm DC jack center pin positive Figure 7 3 Proceed to Attaching the Printer Note Make sure you regularly clean the charging contact points on your printer s case to ensure your printer s batteries are properly charged and avoid damage to printer or charger To clean the charging contact points unplug the charger from the wall and clean using alcohol and a clean rag Warning Do not allow the charging points to come in contact with metal objects Step 2 Attaching the Printer 1 Place the printer s swivel mount block over the unlocked swivel lock bracket Figure 8 Figure 8 2 Facing the printer move the swivel lock s lever from left to right until it clicks into the locked position Figure 9 Figure 9 Warranty The Company warrants that Datamax O Neil products are free from defects in manufacturing materials and workmanship for one 1 year from date of original purchase to Buyer Distributo
Download Pdf Manuals
Related Search