Pyle PDWM5000 microphone
Contents
1. mo io ito POSITION SKETCH OF RECEIVER 1 Power Indicator 7 CH C Volume Control 13 Mixed Audio Output 2 Power Switch 8 CH C Receiving Indivator 14 CH A B Antenna Connector 3 CH AVolume Control 9 CH D Receiving Indicator 15 AC Power Input voltage selectable 4 CH A Receiving Indicator 10 CH D Volume Control 16 CH A Antenna Connector 5 CH B Receiving Indicator 11 CH BAntenna Connector 17 CH C D Antenna Connector 6 CH B Volume Control 12 Individual Audio Output POSITION SKETCH OF TRANSMITTER 1 Cartridge Grille 2 LED Power Indicator 3 Power Switch 4 Mic Body SAFETY DIRECTION 5 Battery Compartment 1 2 3 4 6 1 Read Carefully Read all safety and operation direction carefully before using this product 2 Keep the Manua Keep this Owner s Manual in a safety place for future reference 3 Mind the Cautions Please follow all the cautions indicated on the machine or in the manual 4 Follow the Instruction Please follow all the operation process and operation instruction 5 Safety Environment Don t put the machine in the place of high humidity high electro magnetic field strong sun light and high temperature 6 Attention when Stop Using When stop using for a long time please unpug the AC cord and remove the mic batteries 7 Cleaning Before cleaning please turn off2. PyleAudio com 718 535 1800 718 236 2400 fax 1600 63rd Street Brooklyn NY 11204 COPALE ONERSNANUAL PDWM5000 PROFESSIONAL SERIES WIRELESS MICROPHONE SYSTEM 1 Frequency Rang z 0c6 VHF 160 280MHz 2 Frequency Stability 00 0 0 005 3 Modulation mode 0ee eee VHF 4 Modulation Deviation 0 00 20KHz 5 Audio Frequency Response 40Hz 20KHz 6 SignaltoNoise Ratio gt 60dB 7 Maximum Sound Pressure Level gt 100dB 8 DistortiOn si ec eeeeeds ee acess deere ee 0 5 9 Operating Range 80m under typical conditions 10 Operation Temperature Rang 10 50 o x fa n 3 man o gt 1 RF Output Power eee 100mW MAX 2 Harmonic Suppression ceeeeeee 40dB 3 Antenna sec cinvecee es rey creeds Peewee Builtin 4 Power Requirement 0 9V Battery 5 Nominal Current Drain 4 Approximately 15mA 6 Battery Life 0000000000 00 00 12 hours o o 5 n 3 me oO i 1 Receive Mode Crystal Frequency Lock 2 Sensitiity 0 40dBu S N 60dB 3 SignaltoNoise Ratio 008 gt 60dB 4 Audio Output Levels 0 400mV Max 5 Power Supply AC110V 220V 10 6 Dimension 00 WxDxH 485x240x52mm Thank you for buying our excellent wireless microphone se
3. ensure good receiving signals 2 Open the battery cover of microphone and install the batteries inside the compartment properly then replace the cover 3 Position the transmitter power switch to ON indicator light will glow wid position is MUTE Now the receiver s corresponding channel light will also glow indicating that the receiver has already received the effective signals from the transmitter Adjust the volume knobs of the receiver and power amplifier to ensure the suitable volume for the system Speak with microphone to check the sound 4 When the transmitter power indicator dardens it indicates low battery power Please change with new batterles in time Note to not mix new and old batteries together 5 When using multiple systems at the same time it is necessary to use machines of different frequency System Tumon Process Receiver Mixer or Pre Amplifier Power Amplifier Opposite when Tumoff sis e Introducing a special ALC circuit to ensure nondistortion e Introducing frequency compressingexpanding technique to lower the e Noise and enlarge the dynamic range Superior squelch and high signaltonoise ratio Aimost zero noise output when standby Broad frequency response range super low distortion e Perfect operation status indications REAR PANEL OF RECEIVER
4. ries products Before you use our products please read this Owner s manual for vour corrective operation Please keep this manual in a safety place for your future reference VHF series professional wireless microphone systems introducesa number of advanced techniques and components including the efficient lowconsumption RF transmission impact elimination slowcontrolled output superiorssensitivity VHF narrowband HF and MF filters and 15ppm Crystal Frequency Lock etc Online simulation EDA and strict quality control are applied to ensure each system withexcellent function e Introducing multiple HF and MF narrowband filters to eliminate interfering signal e Introducing low power consumption components to ensure the longer battery life e Special impact wave eliminating circuit for handheld microphone switches e Long practical distance Over 80m in ideal circumstances practiacal 20m radius incomplex circumstances e Multiple frequency design Be able to use two microphones at the same time withoutmutual interference e Applicable for medium amp small stages karaoke halls and home SYSTEM SETUP entertainment etc 1 Plug the provided audio cable into the receiver s ALL output connector and the other end into a mixer or power amplifier system Extend the two antennas fully to the vertical position Switch on the receiver the POWER ON light will glow indicating the machine standby Better keep distances between the receiver and floor to
5. the system power Don t clean it with liquid or sprayer It is suitable to use wet cloth 8 Accessories Only use the provided accessories or other certificated products 9 Power supply The machine is only applicable to the indicated power supply Please confirm whether it is suitable for your district 10 Maintaining To avoid the risk of electric shock don t open or remove the cover to repair the machine by yourself Ask a qualified repairman to repair it 11 Replacing Components Before replace any componen the repairman should check carefully to confirm whether the machine is in safe position 12 Adjustment When the machine is broken down to avoid the great damages don t adjust any adjustable component by yourself You should ask an expert to repair it Or you can also contact with the dealer and we will try all our best to help you O
Download Pdf Manuals
Related Search