Home

Samsung 400CX-3

1. Ensure that the signal cable is firmly connected to the PC or video sources Refer to the Connecting a Computer Ensure that the PC or video sources are turned on Not Optimum Mode message Check the maximum resolution and the frequency of the video Adaptor Compare these values with the data in the Preset Timing Modes Chart The picture rolls vertically Check if the signal cable is securely connected Re connect it if necessary Refer to Connecting a Computer The image is not clear picture is blurred Run Frequency Coarse and Fine tuning Turn on again after removing all accessories video extension cable etc Set the resolution and frequency to the recommended ranges The picture image is unstable and shakes Check if the resolution and frequency set for the computer video card falls in the range supported by the LCD Display If not reset them referring to the current Information under the LCD Display menu and Preset Timing Modes Ghost images are shown in the picture Check if the resolution and frequency set for the computer video card falls in the range supported by the LCD Display If not reset them referring to the current Information under the LCD Display menu and Preset Timing Modes The image is too light or too dark Adjust the brightness and contrast 104 O O O Q RD Troubleshooting Refer to the Brightness Contrast The screen color is inconsistent Adjust color using Custom under
2. AV COMPONENT AUDIO IN R AUDIO L on the LCD Display 2 Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the AV IN VIDEO on the LCD Display 3 Select AV for the Camcorder connection using the SOURCE button on the front of the LCD Display or on the remote control 32 Connections 4 Then start the Camcorder with a tape inserted Note The audio video cables shown here are usually included with a Camcorder If not check your local electronics store If your camcorder is stereo you need to connect a set of two cables Connecting Using a HDMI Cable 1 Connect input devices such as a Blu Ray DVD player to the HDMI IN terminal of the LCD Display using an HDMI cable Note e In HDMI mode only PCM format audio is supported Connecting Using a DVI to HDMI Cable OOO E 1 Connect the DVI output terminal of a digital output device to the HDMI IN terminal of the LCD Display using a DVI to HDMI cable 2 Connect the red and white jacks of an RCA to stereo for PC cable to the same colored audio output terminals of the digital output device and connect the opposite jack to the DVI RGB AUDIO IN terminal of the LCD Display 33 Connections Connecting Using a DVI Cable 1 Connect between the DVI OUT port on the LCD monitor and the input port on another monitor using a DVI cable 2 Connect between the AUDIO OUT port on the LCD monitor and the audio input port on another moni
3. a professional for installation if possible e To connect the RF cable to the antenna input terminal Keep the copper wire portion of the RF cable straight 2 Turn on the LCD Display 3 Select TV using the TV 4 Select a desired TV channel Connecting AV Devices 1 Connect the Video and Audio R AUDIO L port of the DVD VCR or DTV Set Top Box to the Video and Audio R AUDIO L LCD Display 2 Play the DVD VCR or Camcorder with a DVD disc or tape inserted 3 Select AV using the SOURCE button on the front of the LCD display or on the remote 31 Connections Connecting using a Component Cable 1 Connect a set of audio cables between the AV COMPONENT AUDIO IN R AUDIO L on the LCD Display and the AUDIO OUT jacks on the DVD player or other external device 2 Connect the Component to D sub cable sold separately to the product s RGB COM PONENT IN port and the DVD player s COMPONENT PR Y PB ports Note e Select Component using the SOURCE button on the front of the LCD Display or on the remote control e Then start the DVD Player with a DVD disc inserted e A component cable is optional e Foran explanation of Component video consult your DVD or external device s user man ual Connecting to a Camcorder 1 Locate the AV output jacks on the camcorder They are usually found on the side or back of the camcorder Connect a set of audio cables between the AUDIO OUTPUT jacks on the camcorder and the
4. with a soft cloth using either a cleaning solution or plain water Do not leave any detergent or scratches on the case Do not let any water enter the LCD Display How can play the video 106 Troubleshooting A The video supports the MPEG1 and WMV codecs only Install the corresponding codec to play the video Note that some of the codecs can be incompatible Note Before calling for assistance check the information in this section to see if you can remedy any problems yourself If you do need assistance please call the phone number on the In formation section or contact your dealer 107
5. 400CX 2 400CXN 2 460CX 2 460CXN 2 Introduction Package Contents Note Please make sure the following items are included with your LCD Display If any items are missing contact your dealer Contact a local dealer to buy optional items Checking the Contents of the Package V v K Remove the lock from the package box as shown in the figure above Lift up the package box by Check the contents of the Remove the Styrofoam holding the grooves on package and vinyl cover both sides of the package box Note e After unpacking the package make sure to check the contents of the package e Make sure to keep the package box for transporting the product in the future Unpacking LCD Display Introduction Manuals Quick Setup Guide Warranty Card User s Guide Not available in all loca tions dy Magiclnfo Software CD Magiclnfo Manual CD Applicable to the CXN 2 model only Cables Power Cord Others Remote Control Batteries AAA X 2 Cleaning Cloth Not available in all loca tions HDD Cover Applicable to the CXN 2 model only Note Cleaning Cloth is only provided for highly polished black products as a product feature 10 Introduction Sold separately DVI Cable LAN Cable Applicable to the CXN 2 model only a al a ET Pa ral ma z mE ee i _ tJ i Sie We E tuair m J Wall Mount KIT Component to D
6. D MENU 8 TOOLS 9 Up Down Left Right but tons 10 1 INFO 11 COLOR BUTTONS 12 TTX MIX 13 MTS DUAL 14 2 ENTER PRE CH 15 MUTE 16 CH PA 17 TV 18 MENU 19 D RETURN 20 Ul EXIT Introduction The button is used to select Digital channels For exam ple channel 4 1 Adjusts the audio volume Press the button to change the input signal SOURCE Changing the SOURCE is only allowed for external devices that are connected to the LCD Display at the time DTV menu display This function does not work for this LCD Display Use to quickly select frequently used functions Moves from one menu item to another horizontally vertically or adjusts selected menu values Current picture information is displayed on the upper left corner of the screen Press to add or delete channels and to store channels to the favorite channel list in the Channel List menu TV channels provide written information services via tele text Teletext Buttons 05098 08202098 092090908 For more information gt TTX MIX You can select MTS Multichannel Television Stereo mode Audio Type MITS S_Mode Default FM Stereo Mono Mono Manual Stereo Mono Stereo Change SAP Mono SAP Mono This button is used to return to the immediately previous channel Pauses mutes the audio output temporarily This is dis played on the lower left corner of the screen The audio resumes comes back o
7. LAN cable CXN 2 model only Connecting a USB device Note You can connect USB devices such as a mouse or keyboard CXN 2 model only 36 Troubleshooting Self Test Feature Check Note Check the following items yourself before calling for assistance Contact a Service Center for problems that you cannot solve by yourself Self Test Feature Check 1 Turn off both your computer and the LCD Display 2 Unplug the video cable from the back of the computer 3 Turn onthe LCD Display The figure shown below Check Signal Cable appears on a black background when the LCD Display is working normally even though no video signal is detected While in the Self Test mode the LED power indicator remains green and the figure moves around on the screen qr Check Signal Cable PC 4 Turn off your LCD Display and reconnect the video cable then turn on both your com puter and the LCD Display If your LCD Display screen remains blank after using the previous procedure check your video controller and computer system your LCD Display is functioning properly Warning Messages You can even view the screen at a resolution of 1920 x 1080 However you will receive the following message for a minute You can choose to change the screen resolution or stay in the current mode during that time And If the resolution is more than 85Hz you will see the black screen because the LCD Display does not support over 85Hz Not Optimum M
8. OSD Color Adjustment menu The color image is distorted by dark shadows Adjust color using Custom under OSD Color Adjustment menu The color white is poor Adjust color using Custom under OSD Color Adjustment menu The Power Indicator blinks The LCD Display is currently saving the changes made in the settings to the OSD memory The screen is blank and the power indicator light blinks every 0 5 or 1 seconds The LCD Display is using its power management system Press any key on the key board The screen is blank and it is blinking If you see the TEST GOOD message on the screen when you pressing the MENU button check the cable connection between the LCD Display and the computer to en sure that the connector is properly connected Problems related to Audio Note Problems related to audio signals and their solutions are listed below Q A FPF OQO Q A No sound Ensure that the audio cable is firmly connected to both the audio in port on your LCD Display and the audio out port on your sound card Refer to the Connecting a Computer Check the volume level The sound level is too low Check the volume level If the volume is still too low after turning the control to its maximum check the volume control on the computer sound card or software program The sound is too high or too low Adjusts the Treble and Bass to the appropriate levels Problems related to the Remote Control Note Problem
9. e HDMI cable to the PC ensure that you select HDMI from both the Source List and Edit Name before selecting PC or DVI device so that normal PC screen and sound can be outputted e Note that sound is only available when connected according to the op tion 2 that follows Connect the audio cable for your LCD Display to the audio port on the back of the LCD Display Note e Turn on both your computer and the LCD Display e Contact a local SAMSUNG Electronics Service Center to buy optional items Connecting to Other devices Note e AV input devices such as DVD players VCRs or camcorders as well as your computer can be connected to the LCD Display For detailed information on connecting AV input devices refer to the contents under Adjusting Your LCD Display e The LCD Display s configuration at the back may vary slightly depending on the LCD Display model Connecting TV Note You may view television programs on the LCD Display if it is connected to an antenna or CATV cable without installing any separate TV reception hardware or software on your com puter 30 Connections 1 Connect the CATV cable or TV antenna cable to the ANT IN port on the rear side of the LCD Display Make sure to use a TV antenna cable sold separately e When using an interior antenna terminal Check the antenna terminal on the wall first and connect the antenna cable e When using an outdoor antenna If you are using an outdoor antenna use
10. n if MUTE or VOL is pressed in the Mute mode In TV mode selects TV channels Selects the TV mode directly Opens the on screen menu and exits from the menu or closes the adjustment menu Returns to the previous menu Exits from the menu screen 17 Connections Connecting a Computer Note AV input devices such as DVD players VCRs or camcorders as well as your computer can be connected to the LCD Display For detailed information on connecting AV input devices refer to the contents under Adjusting Your LCD Display 11 e P ad will iyd E E ha Cat m Applicable to the CXN 2 model only Connect the power cord for your LCD Display to the power port on the back of the LCD Display Turn on the power switch There are several ways to connect the computer to the monitor Choose one from the following options Using the D sub Analog connector on the video card Connect the D sub to the 15 pin RGB port on the back of your LCD Display and the 15 pin D sub Port on the computer em RGB COMPONENT iP Using the DVI Digital connector on the video card Connect the DVI Cable to the DVI port on the back of your LCD Display and the DVI port on the computer 29 Connections oa CEL eT Using the HDMI digital output on the graphics card e Connect the HDMI IN port on the monitor to the HDMI port on the PC using the HDMI cable Note e When th
11. ode Recommended Mode AeA KX GBOHF Note Refer to Specifications gt Preset Timing Modes for the resolutions or frequencies supported by the LCD Display Maintenance and Cleaning 1 Maintaining the LCD Display Case Clean with a soft cloth after disconnecting the power cord 102 Troubleshooting e Do not use benzene thinner or other flammable sub stances 2 Maintaining the Flat Panel Display Screen Clean with a soft cloth cotton flannel e Never use acetone benzene or thinner it The user will be required to pay costs and related E expenses for repairing damages caused They may cause flaws or deformation of the screen surface e The user is responsible for any damage caused by using these substances Symptoms and Recommended Actions Note A LCD Display recreates visual signals received from the computer Therefore if there is a problem with the computer or the video card this can cause the LCD Display to become blank have poor coloring become noisy etc In this case first check the source of the prob lem and then contact a Service Center or your dealer 1 Check if the power cord and the video cables are properly connected to the computer 2 Check if the computer beeps more than 3 times when booting If it does request service 3 Ifyou installed a new video card or if you assembled the PC check if you installed the Adaptor video 4 Check if the scanning ratio of the video
12. rgy conservation turn your LCD Display OFF when it is not needed or when leaving it unattended for long periods Remote Control Sensor Aim the remote control towards this spot on the LCD Display E Note For detailed information concerning cable connections refer to Connecting Cables under Setup The LCD Display s configuration at the back may vary slightly depending on the model 12 Introduction a POWER S W ON OFF 0 Switches the LCD Display On Off B POWER The power cord plugs into the LCD Display and the wall outlet RS232C OUT IN RS232C Serial PORT MDC Multiple Display Control Program Port O RGB COMPONENT IN PC Video Con nection Terminal e Use a D Sub Cable 15 pin D Sub PC mode Analog PC e Connect the RGB COMPONENT IN port on the monitor to the COMPONENT port on the external device using the D SUB to COMPONENT cable e Connect the RGB COMPONENT IN port on the monitor to the BNC port on the PC using the D SUB to BNC cable 5 DVI IN PC Video Connection Terminal 13 Introduction Use a DVI Cable DVI D to DVI D DVI mode Digital PC O DVI RGB AUDIO IN PC DVI Audio Connection Terminal Input AV COMPONENT AUDIO IN R AU DIO L Connect the port of the DVD VCR DVD DTV Set Top Box to the R AUDIO L port of the LCD Display AV IN VIDEO Connect the VIDEO terminal of your mon itor to the video outp
13. s related to the remote control and their solutions are listed Q The remote control buttons do not respond 105 Q amp A gt Fr F amp F F O Troubleshooting Check the polarities of the batteries Check if the batteries are empty Check if the power is on Check if the power cord is securely connected Check if a special fluorescent or neon lamp is on in the vicinity How can I change the frequency The frequency can be changed by reconfiguring the video card Note That video card support can vary depending on the version of the driver used Refer to the computer or the video card manual for details How can adjust the resolution Windows XP Set the resolution in the Control Panel Appearance and Themes Display Set tings Windows ME 2000 Set the resolution in the Control Panel Display Settings Contact the video card manufacturer for details How can set the Power Saving function Windows XP Set the resolution in the Control Panel Appearance and Themes Display Screen Saver Set the function in the BIOS SETUP of the computer Refer to the Windows Computer Manual Windows ME 2000 Set the resolution at the Control Panel Display Screen Saver Set the function in the BIOS SETUP of the computer Refer to the Windows Computer Manual How can clean the outer case LCD Panel Disconnect the power cord and then clean the LCD Display
14. screen is set to between 50 Hz 85 Hz Do not exceed 60Hz when using the maximum resolution 5 If you have problems in installing the Adaptor video driver boot the computer in Safe Mode remove the Display Adaptor in the Control Panel gt System gt Device Admin istrator and then reboot the computer to reinstall the Adaptor video driver Check List Note e The following table lists possible problems and their solutions Before calling for assis tance check the information in this section to see if you can remedy any problems for yourself If you do need assistance please call the phone number on the Information section or contact your dealer e For more network related information refer to the Magiclnfo Troubleshooting section Problems related to the Installation PC Mode Note Problems related to the LCD Display installation and their solutions are listed 103 Troubleshooting The LCD Display screen flickers Check if the signal cable between the computer and the LCD Display is securely con nected Refer to Connecting a Computer Problems related to the Screen Note Problems related to the LCD Display screen and their solutions are listed Q A gt gt O F F Q gt OD F F LO 2 The screen is blank and the power indicator is off Ensure that the power cord is firmly connected and the LCD Display is on Refer to the Connecting a Computer Check Signal Cable message
15. sub Ca D sub BNC Cable ble Semi Stand KIT Your LCD Display Front MENU button MENU Opens the on screen menu and exits from the menu Also use to exit the OSD menu or return to the previous menu Navigate buttons Down Up buttons Channel buttons Moves from one menu item to another vertically or adjusts selected menu values When OSD is not on the screen press the button to adjust channels 11 Rear Introduction Adjust buttons Left Right buttons Volume buttons Moves from one menu item to another horizontally or adjusts selected menu values When OSD is not on the screen press the button to adjust volume ENTER button ENTER Activates a highlighted menu item SOURCE button SOURCE Switches from PC mode to Video mode Selects the input source that an external device is connected to PC DVI AV Component HDMI Magiclnfo TV Note Magiclnfo supports the CXN 2 model only DMENU Opens the on screen D MENU Power button J Use this button for turning the LCD Display on and off Brightness Sensor Optional Automatically detects the surrounding brightness This function is activated only on the models equipped with an auto bright ness sensor Power indicator Shows PowerSaver mode by blinking green Note See PowerSaver described in the manual for further information regarding power saving functions For ene
16. the illustra tion depending on the manufacturer Refer to the manual provided with the Kensington Lock for proper use The locking device has to be purchased separately Note The location of the Kensington Lock may be different depending on the model Using the Anti Theft Kensington Lock 1 Insert the locking device into the Ken sington slot on the LCD Display and turn it in the locking direction 15 Note Introduction 2 Connect the Kensington Lock cable 3 Fix the Kensington Lock to a desk or a heavy stationary object See Connecting Cables for further information regarding cable connections Remote Control Note The performance of the remote control may be affected by a TV or other electronic device operating near the LCD Display causing a malfunction due to interference with the frequen cy POWER OFF an oe ser o o e GHI JKL MNO B o oo PRS TW WKY 8go UEL SY VBOL ENTER a i GUIDE MUTE AN A SOURCE CHIP oll v jE i es E2 to NaF SAMSUNG 1 POWER 2 O OFF 3 Number Buttons Number Buttons DEL button VOL SOURCE D D MENU TOOLS Up Down Left Right buttons 1 INFO COLOR BUTTONS TTX MIX MTS ENTER PRE CH K MUTE CHA TV DTV MENU 5 RETURN B ExT Magiclnfo Turns the product On Turns the product Off Press to change the channel 16 4 DEL button 5 VOL 6 SOURCE 7 WUI
17. tor using a stereo cable 3 Select DVI using the SOURCE button on the front of the LCD Display or on the remote control amp Note e DVI OUT does not support HDCP Connecting a DIV Set Top Cable Satellite Box 1 Connect the Component to D sub cable sold separately to the product s RGB COM PONENT IN port and the COMPONENT PR Y PB ports on the Set Top Box 2 Connect a set of audio cables between the AV COMPONENT AUDIO IN R AUDIO L on the LCD Display and the AUDIO OUT jacks on the Set Top Box Note e Select Component using the SOURCE button on the front of the LCD Display or on the remote control e For an explanation of Component video see your Set Top Box owner s manual 34 Connections Connecting Using a D SUB BNC Cable 1 Connect the RGB COMPONENT IN port on the monitor to the BNC port on the PC using the D SUB to BNC cable Connecting to an Audio System ER EL J E W 1 Connect a set of audio cables between the AUX L R jacks on the AUDIO SYSTEM and AUDIO OUT on LCD Display Connecting a LAN Cable Note e AV input devices such as DVD players VCRs or camcorders as well as your computer can be connected to the LCD Display For detailed information on connecting AV input devices refer to the contents under Adjusting Your LCD Display e The LCD Display s configuration at the back may vary slightly depending on the LCD Display model 35 Connections Note Connect the
18. ut terminal of the exter nal device using a VIDEO cable DVI OUT e Connect a monitor to another monitor through a DVI cable e Connect the DVI OUT port on the monitor to the HDMI IN port on the other monitor using the DVI to HDMI cable e DVI HDMI and network signals sent via the DVI OUT port are displayed on the second display which has the DVI IN port Note Up to 6 Full HD or 10 HD monitors can be connected May differ depending on the product UDIO OUT Headphone External speaker output termi nal HDMI IN Connect the HDMI terminal at the back of your LCD Display to the HDMI terminal of your digital output device using a HDMI ca ble 11 Up to HDMI cable 1 0 can be supported 14 Introduction ANT Connect the CATV cable or TV antenna ca ble to the ANT IN port on the rear side of the LCD Display Make sure to use a TV an tenna cable sold separately as the antenna cable RGB OUT Note Applicable to the CXN 2 model only LAN LAN Connection Terminal Note Applicable to the CXN 2 model only usa USB Connection Terminal Keyboard Mouse Mass Storage Device Compatible Note Applicable to the CXN 2 model only Kensington Lock The Kensington Lock is a device used to physically fix the system when using it in a public place The locking device has to be purchased separately The appearance and locking method may differ from

Samsung 400CX-3

Contents

Download Pdf Manuals

Related Search

Related Contents