Kenwood Electronics UBZ-LJ8
Contents
1. 11 MENU SETTINGS 12 BEEP TONES 12 BATTERY INDICATOR BATTERY TYPE 13 AUTO POWER OFF APO 14 AUTO CHANNEL SELECT 14 VOICE ACTIVATED CONTROL VOX 16 CALLING ALERT TONES 18 SQUELCH 19 OPERATING FEATURES 20 KEY LOCK 20 LAMP 20 TRANSMIT POWER SAVER 21 BATTERY SAVER 21 LOUDNESS 22 RESETTING THE TRANCEIVER 23 OPTIONAL ACCESSORIES 24 SMC 34 SPEAKER MICROPHONE 25 MONITOR2. 25 ADDITIONAL FUNCTIONS 25 SPECIFICATIONS 26 TRANSCEIVER SPECIFICATIONS 26 CHANNEL FREQUENCY CHART 26 GROUP MODE NUMBERS 27 TK 3101 UBZ LJ8 COMPATIBILITIES 27 TROUBLESHOOTING GUIDE 28 UBZ LJ8 E 000 02 11 20 9 42 AM 1 1 INTRODUCTION Thank you for purchasing this KENWOOD Private Mobile Radio 446 PMR446 This KENWOOD product is a precision device Treat it with care and you will enjoy years of reliable operation PMR446 refers to personal short range Private Mobile Radios for family and friends to keep in touch without the need for a licence radio knowledge or monthly charges Your KENWOOD PMR446 is called a transceiver meaning transmitter and receiver You can choose from eight preset channels to communicate with others For your convenience Automatic Squelch quiets your transceiver when you are not receiving calls and Group Mode keeps your transceiver quiet except for calls you want to hear For your privacy Secret Mode encrypts your messages so you can talk with your group members without having others listen in on your conversation Your transceiver p
3. 19 SQUELCH When no signals are present the squelch on the transceiver automatically mutes the speaker so you will not hear background noise You can however deactivate the squelch This feature is useful for a variety of reasons It allows you to confirm the channel activity so that you don t make a call while another party is using the same channel It allows you to adjust the volume level without having to wait for a call When receiving a call that is intermittent due to a weak signal disabling the squelch will allow you to listen to the call without it continuously cutting out 1 Enter the Menu Settings page 12 and press the L or M key until you reach the Squelch display 2 Press the key to turn the squelch function ON or OFF 3 Press the PTT switch to confirm your setting If you have turned the squelch function OFF the busy icon appears on the display Note Turning the transceiver power OFF will reset the squelch to its default setting When the transceiver is turned back ON squelch is also automatically turned ON UBZ LJ8 E 01 28 02 11 20 9 44 AM 19 20 OPERATING FEATURES KEY LOCK You can lock the L M and keys to prevent accidentally changing the channel and channel settings Additionally while the transceiver is locked you cannot enter the Menu Settings page 12 Press and hold the key for 1 second to lock or unlock the transceiver key
4. GETTING STARTED q q q q q Switch the Power ON by pressing and holding the switch for approximately 1 second A confirmation tone sounds To switch the transceiver power OFF press and hold the switch again for 1 second w w w w w Adjust the Volume by rotating the VOL control Clockwise increases the volume and counterclockwise decreases the volume e e e e e Select a Channel from 1 to 8 by pressing the L and M keys A confirmation tone sounds each time you press a key When you receive a call on your selected channel you will hear audio from the speaker and the busy icon will appear To use a Group Mode number refer to GROUP MODE on page 10 r r r r r Make a Call 1 Press and hold the PTT switch then speak into the microphone to transmit The transmit icon will appear For best sound quality speak into the microphone in your normal speaking voice while holding the microphone approximately 3 to 4 cm 1 5 inches from your lips 2 Release the PTT switch when you have finished speaking UBZ LJ8 E 01 28 02 11 20 9 44 AM 9 10 GROUP MODE Group Mode is a function which allows you to reject signals from undesired parties that are using the same channel as you You will hear audio from the speaker only when you receive a signal that matches your Group Mode number Likewise when you transmit on a channel set up with a Group Mode number the
5. 1 le v e L nia G X O V 3 2 1 F F O F F O 6 1 e m i T y ale D X O V 0 3 0 2 0 1 5 0 s d n o c e s 5 0 s d n o c e s 6 1 s e n o T tr el A g nilla C 0 1 1 1 8 1 h cle u q S F F O N O N O 9 1 UBZ LJ8 E 01 28 02 11 20 9 44 AM 23 24 OPTIONAL ACCESSORIES EMC 3 Clip Microphone and Earphone PTT SENS VOX PTT HMC 3 VOX PTT Headset KHS 21 Headset SMC 32 Speaker Microphone SMC 33 Speaker Microphone VOLUME MIN SMC 34 Speaker Microphone 2 1 UBC 4 Battery charger CHARGING RED UBC 2 Twin charger UPB 1 Rechargable NiCd battery pack USC 3 Carrying case UBZ LJ8 E 01 28 02 11 20 9 44 AM 24 25 SMC 34 SPEAKER MICROPHONE The SMC 34 speaker microphone provides you with the following additional functions and features Remote VOLUME control Remote PTT switch Remote speaker microphone MONITOR Monitor operates similar to the transceiver s squelch function but can be used momentarily at short notice To open the squelch for the channel you are listening to press and hold key 1 on the microphone While you are pressing this key squelch remains open Release this key to close the squelch again ADDITIONAL FUNCTIONS In the Menu Setup you can use microphone keys 2 and 3 in place of the transceiver L and M keys re
6. 8 1 UBZ LJ8 E 01 28 02 11 20 9 44 AM 26 27 GROUP MODE NUMBERS y alp si D r e b m u N e d o M p u o r G y c n e u q e r F y alp si D r e b m u N e d o M p u o r G y c n e u q e r F y alp si D r e b m u N e d o M p u o r G y c n e u q e r F F O F F O 3 1 z H 5 3 0 1 6 2 z H 2 2 6 1 1 z H 0 7 6 4 1 z H 2 7 0 1 7 2 z H 9 7 6 1 2 z H 9 1 7 5 1 z H 9 0 1 1 8 2 z H 8 3 7 1 3 z H 4 4 7 6 1 z H 8 4 1 1 9 2 z H 9 9 7 1 4 z H 0 7 7 7 1 z H 8 8 1 1 0 3 z H 2 6 8 1 5 z H 7 9 7 8 1 z H 0 3 2 1 1 3 z H 8 2 9 1 6 z H 5 2 8 9 1 z H 3 7 2 1 2 3 z H 5 3 0 2 7 z H 4 5 8 0 2 z H 8 1 3 1 3 3 z H 7 0 1 2 8 z H 5 8 8 1 2 z H 5 6 3 1 4 3 z H 1 8 1 2 9 z H 5 1 9 2 2 z H 3 1 4 1 5 3 z H 7 5 2 2 0 1 z H 8 4 9 3 2 z H 2 6 4 1 6 3 z H 6 3 3 2 1 1 z H 4 7 9 4 2 z H 4 1 5 1 7 3 z H 8 1 4 2 2 1 z H 0 0 0 1 5 2 z H 7 6 5 1 8 3 z H 3 0 5 2 TK 3101 UBZ LJ8 COMPATIBILITIES s g nitte S tlu afe D 1 0 1 3 K T s g nitte S elbita p m o C 8 J L Z B U 1 le n n a h C
7. 12 13 3 Press the PTT switch or turn the transceiver power OFF to confirm your setting BATTERY INDICATOR BATTERY TYPE The battery indicator on the display lets you know approxi mately how much battery life is remaining When the battery voltage becomes too low while transmitting the transceiver stops transmitting and a tone sounds until you release the PTT switch Recharge or replace the battery pack at this time High battery power Medium battery power Low battery power Time to replace the batteries or recharge the battery pack Depending on the type of batteries you are using in the transceiver adjust the battery type to match The battery indicator can only accurately read out the remaining battery power if this value is set correctly An incorrect setting will result in an inaccurate battery power readout on the display 1 Enter the Menu Settings page 12 and press the L or M key until you reach the display 2 Press the key to set the value to alkaline batteries or to the optional UPB 1 battery pack You must set this menu each time the battery type is changed 3 Press the PTT switch or turn the transceiver power OFF to confirm your setting UBZ LJ8 E 01 28 02 11 20 9 44 AM 13 14 AUTO POWER OFF APO Auto Power Off is useful when you unintentionally leave the transceiver power ON This function saves battery consump tion After two hours elapse with no controls adj
8. 44 AM 2 3 ORIENTATION key VOL control SP MIC jacks Microphone Power switch Antenna Display PTT switch L key M key Speaker CONTROL FUNCTIONS PTT Push to Talk switch Press this switch then speak into the microphone to make a call Release the switch to receive L key Press to increase the channel or group mode number and to turn selected functions ON or OFF M key Press to decrease the channel or group mode number and to turn selected functions ON or OFF VOL control Rotate to adjust the volume level Power switch Press and hold to turn the transceiver power ON or OFF With the power ON press momentarily to enter the Loud Function setting key Press momentarily to enter the Group Mode setting Press momentarily again to enter the Secret Mode setting Press a third time to return to normal Press and hold to lock the transceiver controls UBZ LJ8 E 01 28 02 11 20 9 44 AM 3 4 DISPLAY d e k c ol n e e b e v a h slo rt n o c r e vie c s n a rt e h t n e h w s r a e p p A 0 2 e g a p 3 1 e g a p r e w o p y r e tt a b g ninia m e r e h t s y alp si D d e t a vitc a n e e b s a h e d o M t e r c e S e h t n e h w s r a e p p A 1 1 e g a p d e n r u t e b n a c e d o M t e r c e S n e h w s k nilb d n a s r a e p
9. quality alkaline batteries to enjoy longer periods of battery life You can also use an optional UPB 1 NiCd battery pack When using an optional battery pack be sure to set the battery indicator type to battery pack from its default setting of alkaline batteries Refer to page 13 for details on how to set the indicator type Average alkaline battery life 24 hours Average battery pack life 12 hours Average times are calculated using 10 transmit time 10 receive time and 80 standby time Note Before installing removing batteries you must rotate the antenna out of the way page 6 1 Release the battery cover lock then slide the cover away from the transceiver 2 Insert or remove 3 LR6 AA batteries or the optional UPB 1 NiCd battery pack Mate the battery polarities with those marked on the battery compartment When removing the battery pack pull on the ribbon that is attached to the pack to dislodge the pack from the battery compartment PREPARATION Battery cover Lock UBZ LJ8 E 01 28 02 11 20 9 44 AM 5 6 3 Align the battery cover tabs with the slots on the transceiver hold the cover in place then latch it with the battery cover lock Note N Do not mix old and new batteries or batteries of different types N When you do not use the transceiver for an extended period of time remove the batteries from the transceiver SETTING THE ANTENNA Before using the transceiver be sure
10. receiving station must have a matching Group Mode number in order to hear your call You can select a Group Mode number from 1 to 38 or OFF After changing your Group Mode number confirm that the other members in your group have selected the same number 1 Press the key The current setting appears with a flashing arrow 2 Press the L or M key to select your desired value The values range from 1 to 38 OF means you have selected no Group Mode number Refer to page 27 for the actual Group Mode numbers 3 Press the key two times to confirm the setting UBZ LJ8 E 01 28 02 11 20 9 44 AM 10 11 SECRET MODE Whereas the Group Mode function page 10 allows you to ignore unwanted calls Secret Mode allows you to hold a conversation in complete privacy When activated any other party listening in on your channel will be unable to understand your conversation The transceiver scrambles your voice so that anybody listening in on your conversation will not be able to understand what you are saying In order for members of your own group to understand your call while you are using Secret Mode all other members must also activate Secret Mode on their transceivers This scrambles everybody s voice while transmitting and unscrambles the voice message on your own transceiver when you receive the message Note In order to enter Secret Mode you must also select a Group Mode number If you have not selecte
11. 0 1 e d o M p u o r G 1 le n n a h C 6 le n n a h C 8 1 e d o M p u o r G 2 le n n a h C 3 le n n a h C 3 1 e d o M p u o r G 3 le n n a h C 5 le n n a h C 7 1 e d o M p u o r G 4 le n n a h C 8 le n n a h C 7 e d o M p u o r G 5 le n n a h C 2 1 le n n a h C 6 e d o M p u o r G 6 le n n a h C 7 le n n a h C 9 1 e d o M p u o r G 7 le n n a h C 0 1 le n n a h C 5 1 e d o M p u o r G 8 le n n a h C UBZ LJ8 E 01 28 02 11 20 9 44 AM 27 28 TROUBLESHOOTING GUIDE m elb o r P n oitulo S e h t n r u t t o n n a C r e w o p r e vie c s n a rt N O y a m k c a p y r e tt a b r o s eir e tt a b e h T r o s eir e tt a b e h t e c alp e R d a e d e b k c a p y r e tt a b e h t e c alp e r r o e g r a h c e r d ella ts ni e b t o n y a m s eir e tt a b e h T s eir e tt a b e h t e v o m e R yltc e rr o c nia g a m e h t lla ts ni d n a r e w o p y r e tt a B r e tf a yltr o h s s eid g nig r a h c d e h sinif si e fil k c a p y r e tt a b e h T ti e c alp e R r o o t kla t t o n n a C r e h t
12. UBZ LJ8 FM TRANSCEIVER INSTRUCTION MANUAL EMETTEUR RECEPTEUR FM MODE D EMPLOI TRANSCEPTOR DE FM MANUAL DE INSTRUCCIONES RICETRASMETTITORE FM MANUALE DI ISTRUZIONI FM HANDFUNKSPRECHGER T BEDIENUNGSANLEITUNG FM ZENDONTVANGER GEBRUIKSAANWIJZING B62 1669 10 E 09 08 07 06 05 04 03 02 01 UBZ LJ8 E 00 Cover 02 11 20 9 41 AM 1 CONTENTS INTRODUCTION 1 SUPPLIED ACCESSORIES 1 PRECAUTIONS 2 ORIENTATION 3 CONTROL FUNCTIONS 3 DISPLAY 4 PREPARATION 5 INSTALLING REMOVING BATTERIES 5 SETTING THE ANTENNA 6 INSTALLING REMOVING THE BELT CLIP 7 INSTALLING REMOVING OPTIONAL ACCESSORIES 8 GETTING STARTED 9 GROUP MODE 10 SECRET MODE
13. an area with excessive ambient noise Before VOX will operate you must set a VOX Gain Level 1 Enter the Menu Settings page 12 and press the L or M key until you reach the VOX display 2 Press the key to set the VOX Gain Level from 1 to 3 where 3 is the most sensitive setting or OFF 3 Press the PTT switch or turn the transceiver power OFF to confirm your setting If you have turned the VOX function ON by selecting a VOX Gain Level other than OFF the VOX icon appears on the display UBZ LJ8 E 01 28 02 11 20 9 44 AM 16 17 When operating VOX if you find that the transceiver returns to receive mode too quickly after you stop speaking the end of your message may not be transmitted To avoid this select an appropriate delay time to allow your entire message to be transmitted However do not make the delay overly long 1 Enter the Menu Settings page 12 and press the L or M key until you reach the VOX display This menu is only available if the VOX Gain Level has been set to any value other than OFF 2 Press the key to set the VOX Delay Time from 0 5 to 3 0 seconds 3 Press the PTT switch or turn the transceiver power OFF to confirm your setting When you have activated the VOX function and selected an appropriate Gain Level and Delay Time you can then operate the transceiver hands free To use VOX 1 To transmit simply speak into the headset mic
14. ansceiver automatically stops transmitting Thirty seconds before the time expires the number 30 will appear and blink on the display in place of your Group Mode number Ten seconds before the time expires a tone will sound BATTERY SAVER This transceiver has been designed to give you the most out of your battery power The battery saver decreases the amount of power used when a signal is not being received and no operations are being performed While using the transceiver the battery saver will automatically switch ON after 5 seconds have elapsed with no operations or received calls Operating the transceiver or receiving a call will switch the feature OFF until 5 seconds of non operation occurs again UBZ LJ8 E 01 28 02 11 20 9 44 AM 21 22 LOUDNESS This transceiver has a built in booster amplifier You can control the volume level by rotating the VOL control However if you are in an environment with excessive ambient noise you may find that it is difficult to hear the audio from the transceiver even with the volume increased to its maximum value In such a case you can switch the internal booster amplifier ON to further increase the volume level 1 Momentarily press the switch to enter the Loudness setting 2 Press the L or M key to turn the booster amplifier ON or OFF 3 Press the switch or the key to confirm your setting If you have turned the booster amplifier function ON the LOUD ic
15. d a Group Mode number do so before following the instructions given below 1 Press the key two times The privacy icon appears with a flashing arrow 2 Press the L or M key to turn Secret Mode ON or OFF An image appears in the privacy box when Secret Mode is ON 3 Press the key again to confirm the setting UBZ LJ8 E 01 28 02 11 20 9 44 AM 11 12 MENU SETTINGS Your transceiver has a hidden setting menu which allows you to adjust a variety of features to your desired settings To enter Menu Setting 1 Press and hold the L key while turning the transceiver power ON 2 To view the various settings press the L or M key Following are a list of the settings available Beep ON OFF Battery Type Alkaline Batteries UPB 1 Battery Pack APO Auto Power Off ON OFF Auto Channel Select Remove Add VOX Voice Activated Control Gain Level OFF 1 2 3 VOX Delay Time Only available when VOX Gain Level is not OFF Refer to page 17 0 5 1 0 2 0 3 0 seconds Calling Alert Tone 1 10 Squelch ON OFF 3 Refer to the appropriate sections below for details of adjusting each setting BEEP TONES You can turn the transceiver beep tones ON or OFF as desired 1 Enter the Menu Settings above and press the L or M key until you reach the BEEP display 2 Press the key to turn the beep tones ON or OFF UBZ LJ8 E 01 28 02 11 20 9 44 AM
16. o r a e h r u o y ni s r e b m e m p u o r g e m a s e h t g nis u e r a u o y e r u s e k a M r e b m u n e d o M p u o r G d n a le n n a h c s r e b m e m p u o r g r u o y s a e b y a m s r e b m e m p u o r g r e h t O r u o y n o n r u T e d o M t e r c e S g nis u e d o M t e r c e S s r e vie c s n a rt o o t e b y a m s r e b m e m p u o r g r e h t O e r a u o y e r u s e k a M y a w a r a f r e h t o e h t f o e g n a r nih ti w s r e vie c s n a rt s e cio v r e h t O p u o r g s e dis e b e r a s r e b m e m e h t n o t n e s e r p le n n a h c r e b m u n e d o M p u o r G e h t e g n a h C s r e b m e m p u o r g lla e r u s e k a M h ct a m o t s r e vie c s n a rt rie h t e g n a h c r e b m u n e d o M p u o r G w e n e h t si r e vie c s n a rt e h T r o f g nin oitc n u fla m t n e r a p p a o n n o s a e r d e bir c s e d s a r e vie c s n a rt e h t t e s e R 3 2 e g a p n o UBZ LJ8 E 01 28 02 11 20 9 44 AM 28
17. om your transceiver or add it to your transceiver 3 Press the PTT switch or turn the transceiver power OFF to confirm your setting 1 Press and hold the L key for approximately 1 second The SCAN icon appears on the display 2 When a signal is detected and the Group Mode number matches the channel number blinks 3 When the signal is no longer present the transceiver waits for 10 seconds before scanning continues If a new signal appears before the 10 seconds elapse the transceiver will remain on the channel until the new signal is no longer present When you have added Auto Channel Select to your transceiver you can then operate scan while using the transceiver To begin scanning UBZ LJ8 E 01 28 02 11 20 9 44 AM 15 16 4 To end the scan at any time press the L M or key VOICE ACTIVATED CONTROL VOX Using the VOX feature you can operate the transceiver hands free For best operating conditions we recommend you use an optional headset with both an ear piece and a microphone on a boom that rests in front of your mouth With VOX activated your voice level will determine when the transceiver transmits Because of this you must take care that the ambient noise around you is not so loud that it causes the transceiver to transmit Due to the automatic switching between transmission and reception we recommend you set the VOX gain such that it will not activate transmission when in
18. on appears on the display Note N The Loudness function will not operate if you are using an optional speaker microphone N The booster amplifier uses more battery power Thus while using the Loudness function the battery life will become shorter UBZ LJ8 E 01 28 02 11 20 9 44 AM 22 23 RESETTING THE TRANSCEIVER At some point in time you may desire to reset the transceiver settings to their default values The default values of all the menus and channel settings are listed in the table below To reset the transceiver 1 Turn the transceiver power OFF 2 Press and hold the L and M keys while turning the transceiver power ON appears on the display LJ8 is the transceiver model name 3 Release the keys to reset the transceiver e m a N u n e M s g nitte S elb alia v A tlu afe D g nitte S fe R e g a P r e b m u N e d o M p u o r G 8 3 1 F F O F F O 0 1 e d o M t e r c e S N O F F O F F O 1 1 s s e n d u o L N O F F O F F O 2 2 e n o T p e e B N O F F O F F O 2 1 r o t a cid n I y r e tt a B e p y T y r e tt a B k c a P y r e tt a B e nila kl A e nila kl A 3 1 O P A ff O r e w o P o t u A N O F F O F F O 4 1 tc ele S le n n a h C o t u A d d A e v o m e R e v o m e R 4
19. p a 1 1 e g a p F F O r o N O n e e b s a h n oitc n u f ff O r e w o P o t u A e h t n e h w s r a e p p A 4 1 e g a p d e t a vitc a 4 1 e g a p g nin n a c s elih w s r a e p p A 6 1 e g a p e s u ni si n oitc n u f X O V e h t elih w s r a e p p A g nitti m s n a rt elih w s r a e p p A si h cle u q s e h t elih w r o la n gis a g nivie c e r elih w s r a e p p A 9 1 e g a p d e t a vitc a e d n e e b s a h r eifilp m a oid u a la n r e t ni e h t n e h w s r a e p p A 2 2 e g a p d e t a vitc a F F O r o N O n oitc n u f p e e b e h t g nitt e s elih w s r a e p p A 2 1 e g a p 8 o t 1 r e b m u n le n n a h c t n e rr u c e h t s y alp si D r o 8 3 o t 1 r e b m u n e d o M p u o r G t n e rr u c e h t s y alp si D 0 1 e g a p F O F F O n a c r e b m u n e d o M p u o r G e h t n e h w s k nilb d n a s r a e p p a 0 1 e g a p d e tc ele s e b UBZ LJ8 E 01 28 02 11 20 9 44 AM 4 5 INSTALLING REMOVING BATTERIES This transceiver requires 3 LR6 AA batteries Use high
20. rophone You do not need to press the PTT switch the transceiver automatically detects your voice and begins transmitting 2 To stop transmitting stop speaking Transmission will continue momentarily after you stop speaking You can select the delay time as described above 3 To exit VOX operation set the VOX gain level page 16 to OFF UBZ LJ8 E 01 28 02 11 20 9 44 AM 17 18 CALLING ALERT TONES Calling Alert Tones are used to identify yourself to your party members You can set up a Calling Alert Tone to one of ten types If each party member uses a different tone it is easy to know who is making the call To select your Calling Alert Tone 1 Enter the Menu Settings page 12 and press the L or M key until you reach the Calling Tone display 2 Press the key The current Calling Alert Tone number blinks and the Calling Alert Tone sounds 3 Press the L or M key to select your desired Calling Alert Tone from 1 to 10 The selected Calling Alert Tone sounds each time you press the L or M key 4 Press the PTT switch or turn the transceiver power OFF to confirm your setting To use the Calling Alert Tone 1 Press the PTT switch to transmit as normal 2 Before speaking into the microphone momentarily press the L key Your Calling Alert Tone is transmitted to your party members 3 Continue your call as normal UBZ LJ8 E 01 28 02 11 20 9 44 AM 18
21. rovides safety and convenience almost anywhere The talk range depends on your location you ll get maximum distance of up to approximately 3 2 km 2 miles in open areas less in buildings and vehicles Information KENWOOD is on the web http www kenwood com SUPPLIED ACCESSORIES Carefully unpack the transceiver Make sure the following items are included in your kit before discarding the packing material Transceiver Belt clip Instruction manual Warranty card UBZ LJ8 E 01 28 02 11 20 9 44 AM 1 2 PRECAUTIONS Refer service to qualified technicians only Do not modify or attempt to adjust the transceiver for any reason Do not expose the transceiver to long periods of direct sunlight nor place it close to heating appliances Do not place the transceiver in excessively dusty humid and or wet areas nor on unstable surfaces Avoid extremes in exposure to weather heat and cold This transceiver can be used in mild weather conditions but it is not waterproof Turn OFF your transceiver while taking on fuel or while parked in gasoline service stations Do not operate your transceiver or charge your battery pack in an explosive atmosphere gases dust fumes etc If an abnormal odor or smoke is detected coming from the transceiver immediately switch OFF the power and remove the batteries Contact your KENWOOD dealer UBZ LJ8 E 01 28 02 11 20 9
22. s The icon appears on the display when the transceiver keys are locked No icon appears when they are unlocked While the key lock function is active you can still perform the following functions Power ON OFF Volume adjustment Receive transmit Monitor Calling Alert Tones Full reset LAMP The lamp is used to illuminate the Liquid Crystal Display Each time a key is pressed other than the PTT switch or the VOL control the lamp turns ON and remains on for 5 seconds If you press a key while the lamp is already on the lamp timer will reset the 5 second countdown Note There is no key to turn the lamp OFF It will turn OFF automatically UBZ LJ8 E 01 28 02 11 20 9 44 AM 20 21 TRANSMIT POWER SAVER The purpose of the Transmit Power Saver is to prevent you from transmitting continuously for a long time This function is useful for example when you accidentally keep the PTT switch pressed If you continuously transmit for 3 minutes the transceiver will stop transmitting and a tone will sound To stop the tone release the PTT switch You can press the PTT switch again to resume transmitting The 3 minute timer cannot be adjusted This transceiver is also equipped with a visual warning 30 seconds before the Transmit Power Saver time expires and a pre alert tone which sounds 10 seconds before the time expires This will allow you to finish your message before the tr
23. spectively Pressing key 2 will cause the lamp to turn ON Pressing and holding key 2 will activate scan Pressing key 2 momentarily will end scan Pressing key 3 will transmit your Calling Alert Tone even if you do not first press and hold the PTT switch VOLUME MIN 3 2 1 LOCK ON PTT switch Earphone jack Speaker microphone LOCK switch Rotatable clip Key 1 Key 3 Key 2 VOLUME control UBZ LJ8 E 01 28 02 11 20 9 44 AM 25 26 SPECIFICATIONS r e b m u N le n n a h C y c n e u q e r F e vie c e R ti m s n a r T 1 z H M 5 2 6 0 0 6 4 4 2 z H M 5 7 8 1 0 6 4 4 3 z H M 5 2 1 3 0 6 4 4 4 z H M 5 7 3 4 0 6 4 4 5 z H M 5 2 6 5 0 6 4 4 6 z H M 5 7 8 6 0 6 4 4 7 z H M 5 2 1 8 0 6 4 4 8 z H M 5 7 3 9 0 6 4 4 CHANNEL FREQUENCY CHART TRANSCEIVER SPECIFICATIONS r e w o P t u p t u O F R W m 0 0 5 ytilib a t S y c n e u q e r F m p p 4 e g a tlo V g nit a r e p O C D V 0 5 V 4 3 s n oitc ejo r p s n ois n e m i D d e d ulc nit o n m m 0 0 1 x 6 2 x 6 5 ni 6 1 5 1 3 x 4 6 1 1 x 4 6 3 1 2 A A 6 R L 3 h ti w t h gie W s eir e tt a b z o 3 6 g 0
24. to raise the antenna Ribbon Label Contacts Battery pack installation Battery installation UBZ LJ8 E 01 28 02 11 20 9 44 AM 6 7 INSTALLING REMOVING THE BELT CLIP 1 To install the belt clip align the clip with the guides on the rear of the transceiver then slide the belt clip up until it latches in place 2 To remove the belt clip press the locking latch in then slide the belt clip down before pulling it away from the transceiver Locking latch UBZ LJ8 E 01 28 02 11 20 9 44 AM 7 8 INSTALLING REMOVING OPTIONAL ACCESSORIES Note Always switch OFF the transceiver power when installing or removing the optional accessories The following accessories can be used with this transceiver EMC 3 Clip Microphone and Earphone HMC 3 VOX PTT Headset KHS 21 Headset SMC 32 Speaker Microphone SMC 33 Speaker Microphone SMC 34 Speaker Microphone To install these accessories 1 Open the SP MIC tabs on the side of the transceiver 2 Insert the accessory s plugs into the SP MIC jacks 3 When you remove the accessory from the transceiver be sure to cover the SP MIC jacks with the attached tabs in order to keep dust and dirt away from the contacts Note N Refer to the accessory instruction manuals for detailed instructions on each of the accessories N The transceiver is not water resistant while using accessories UBZ LJ8 E 01 28 02 11 20 9 44 AM 8 9
25. usted or activated and no calls received APO turns the transceiver power OFF One minute before power is turned OFF a warning tone sounds even if the beep tone has been turned OFF 1 Enter the Menu Settings page 12 and press the L or M key until you reach the APO display 2 Press the key to turn the Auto Power Off function ON or OFF 3 Press the PTT switch or turn the transceiver power OFF to confirm your setting If you have turned the APO function ON the APO icon appears on the display AUTO CHANNEL SELECT Auto Channel Select allows you to scan the transceiver channels to search for a signal When the transceiver verifies a signal on a channel it proceeds to check whether or not its Group Mode number matches that which is set up on your transceiver Auto Channel Select will not operate if no Group Mode number is selected If the Group Mode number matches the transceiver stops at the channel and opens the squelch so you can listen to the call If the Group Mode number does not match the call is ignored and scanning continues UBZ LJ8 E 01 28 02 11 20 9 44 AM 14 15 Before you can use the Auto Channel Select function ensure that it is activated You can add or remove this function to from your transceiver using the Menu Settings 1 Enter the Menu Settings page 12 and press the L or M key until you reach the SCAN display 2 Press the key to remove Auto Channel Select fr
Download Pdf Manuals
Related Search