Home

Intel SC5250-E computer case

1. 186 0 Figure 6 450 W EPS 2 0 Power Supply 3 1 2 450 W Power Supply Fan Requirements The 450 W EPS power supply incorporates an 80 mm low acoustic noise fan to exhaust air The sound pressure level is measured at a distance of 1 0 meter from each side of the power supply in a free field The worst case peak value of the measurements shall not exceed 43 dBA at 25 C inlet temperature Revision 1 02 Intel order number C32881 001 Intel amp Entry Server Chassis SC5250 E Chassis Power Subsystem 3 1 3 AC Power Line The system is specified to operate from 100 127VAC 200 240VAC at 50 or 60 Hz The specified PFC power supplies are auto ranging The system is tested to meet these line voltages and has been tested but not specified at 410 of the voltage ranges and at 3 Hz on the line input frequency The system is specified to operate without error at full power supply output load nominal input voltage with line source interruptions not to exceed one period of the AC input power frequency i e 20 milliseconds at 50 Hz The system is not damaged by AC surge ring wave up to 2 0kV 5004A This ring wave is a 100 kHz damped oscillatory wave with a specified rise time for the linear portion of the initial half cycle of 0 5usec Additionally the system will not be damaged by a unidirectional surge waveform of up to 2 0kV 3000A with a 1 2usec rise time and 50usec duration Additional deta
2. 24 5 8 Hard Drive Activity LED E 25 5 9 Hard Drive Fault LED ai eae en ee e e utc EE GE eed oe eae E E ee E 25 5 10 Hot Swap Drive Bay ElectrOoniCS iese se ee ee Ge Ee Ee Gee Ge RR AK Rae eene eee enin nnne 27 Revision 1 02 Intel order number C32881 001 Intel amp Entry Server Chassis SC5250 E Table of Contents 5 10 1 SCSPHSBP Board Layout EE 28 5 10 2 SCSI Hot Swap Backplane Specifications iii es ee eek RR AR RA RR AAR AR Re RR AAR ee Re ee 28 5 10 3 SAF TE Board WE e EE 29 5 11 SAF TE Specifications enit ier eme re a fade axe a ER eg beg ske gte Ego E eda 30 5 12 Serial ATA SATA Hardware Overview mmm enne 30 6 Functional Specifications eroi reo coeur oce dee deel isi ed So oe cora ek De ie ie 31 6 1 Hot Swappable Controller HSC Hardware Configurations esse ee ee ees see ee ee ee ee ee ee 31 f System Peripheral BaVS sine EE UR ske Be ede Nee Ge goe ewe PER ee Dee eN De ee Ge ie 32 7 1 3 5 inch Hot swap Hard Drive BayS iis sesse see ee de ke de dee Dee Geek ee Sea ae Ge ee tente 32 EZ E GE OE EE E AR BROER E 32 delt Device SATA TD nev nai Ee 32 7 4 Hard Drive Activity LED cup eere EERSTEN e 33 1 5 Hard Drive Fault LED ih ENEE eege mu er b bo Et 33 7 6 Hot Swap Drive Bay Electronics sx adr rre ent dandas degen 35 TOM SATA Board weeder 35 7 6 2 SATA Hot swap Backplane Gpechfcattons sss 37 EL eds EE ebe BEE ERENNERUNG Ge Ge 37 8 System Interconn EtON eek EERW taxa aue De
3. 4 3 Cooling Solution Air should flow through the system from front to back as indicated by the arrows in the figure below Figure 7 Cooling Fan Configuration The Intel Server Chassis SC5250 E is engineered to provide sufficient cooling for all internal components of the server including the power subsystem server board processors memory add in PCI cards and installed hard drives and removable media drives 10 Revision 1 02 Intel order number C32881 001 Intel amp Entry Server Chassis SC5250 E System Cooling The server chassis SC5250 E cooling subsystem is dependent upon proper airflow The designated cooling vents on both the front and back of the chassis must be left open and must not be blocked by improperly installed devices All internal cables must be routed in a manner that does not impede airflow The active processor cooling solution validated with this chassis is called a Processor Wind Tunnel PWT and is provided with the boxed Intel Xeon processors To ensure proper cooling only processors with active heatsinks should be used unless otherwise indicated in the server board manuals Active heatsinks incorporate a fan to provide cooling This thermal solution is included with boxed Intel Xeon processors Proper installation of the processor wind tunnel and fan places the fan portion of the PWT towards the front edge of the chassis blowing air toward the rear of the chassis toward I O connectors P d
4. Tl Figure 8 Processor Wind Tunnel Illustration with Intel Xeon Processor with 400MHz System Bus Speed Revision 1 02 11 Intel order number C32881 001 System Cooling Intel amp Entry Server Chassis SC5250 E Figure 9 Processor Wind Tunnel Illustration with Intel Xeon Processor with 533MHz System Bus Speed 4 4 Intel APTWKTCOOLKIT for SE7505VB2 Intel Server Board Configuration The Workstation Cooling Kit was designed to work with the Intel Server Board SE7505VB2 and Intel Server Chassis SC5250 E to dramatically reduce system level acoustics making it an effective solution when acoustics is a concern Intel product code APTWKTCOOLKIT Intel MM 858795 Bios version 1 08 or newer is required for proper performance In addition it is recommended that system fans be connected to the Intel server board SYS Fan header 1 and SYS Fan header 3 for the chassis fans BIO 1 08 includes support for new APWKTCOOLKIT for C5250 E configurations and SE7505VB2 BIOS 1 08 with SE7505VB2 Fab 701 or later on SC5250 E only requires BIOS system set up configurations via BIOS Setup Configuration Utility Settings must be configured as follows Select Advanced menu option Select Hardware monitor option Select Chassis Type and select SC5250 E for Pilot Point 1 configurations 12 Revision 1 02 Intel order number C32881 001 Intel amp Entry Server Chassis SC5250 E System Cooling New BIOS release 1 08 pro
5. 001 System Cooling Intel amp Entry Server Chassis SC5250 E 4 8 Install the Front Fan Spacers for the Fixed Hard Drive Bay Install the Front Fan Spacers for systems with a standard fixed hard drive bay cage The following instructions do not apply to systems with a hot swappable hard drive bay cage Use four screws to attach the four plastic spacers to the unlabeled side of the Front Fan Insert screw letter B in the following figure from the inside of the Front Fan to secure the plastic spacer letter A in the figure Hold the screw steady with your thumb while using a hex driver letter C in figure to secure the plastic spacer to the screw TP00573 Figure 20 Installing Front spacers for the Fixed Hard Drive Bay 1 Insert the Front Fan into the hard drive bay cage Make sure that the Front Fan cable is positioned at the bottom of the cage Make sure that the airflow is towards the server board This means that the label should face to the inside of the hard drive bay cage towards the server board The plastic spacers should be facing towards the front grill of the hard drive bay cage Je X8 e We 2 fe 01 2 Va 2 We f TP00571 Figure 21 Reinstalling Fan with Front spacers to the Fixed Hard Drive Bay 20 Revision 1 02 Intel order number C32881 001 Intel amp Entry Server Chassis SC5250 E System Cooling 2 Use four screws to secure the Front Fan to the hard drive bay cage D
6. Ay er mo uo LLI LL We es H LUCIA A H ON EH H A Lee E EA KOW 7 Tr A Alternate Serial B port knockout B Alternate ICMB or external SCSI knockout C AC input power connector D Power supply E Fan VO ports G Expansion slot covers F ICMB or external SCSI knockout Serial B port knockout H Location to install padlock loop K Chassis intrusion switch J Figure 3 Rear Closed View of Server Chassis SC5250 E Revision 1 02 Intel order number C32881 001 Intel Entry Server Chassis SC5250 E TP00053C TP00054C SGOgaagaagagagag d p 2333933939939339 2 5J SEOOGOOGJdGdOddgs Revision 1 02 Intel order number C32881 001 Chassis Jeans OER A f Joe foala d EE AR eeh GE A e W Ke VE ECKE Ser ex Figure 4 Front Internal View for Server Chassis SC5250 E Figure 5 Rear Internal View for Server Chassis SC5250 E Intel amp Entry Server Chassis SC5250 E Chassis Power Subsystem 3 Chassis Power Subsystem The Intel Server Chassis SC5250 E supports a typical PS 2 form factor power supply with a remote enable feature The remote enable feature perm
7. Baffle Installed 5 10 Hot Swap Drive Bay Electronics The hot swap SCSI backplane board set supports the following features e Hot swapping of SCSI drives that allows connecting SCSI devices while the system power is on e Enclosure management and monitoring functions conforming to the SCS Accessed Fault Tolerant Enclosures Specification SAF TE Revision 1 00 Revision 1 02 27 Intel order number C32881 001 System Peripheral Bays Intel Entry Server Chassis SC5250 E 5 10 1 SCSI HSBP Board Layout The following diagram shows the layout of components and connectors on the hot swap SCSI backplane printed circuit board set This solution consists of two separate boards The first board provides power distribution and SCSI interfacing of the drives The second board provides the SAF TE features and drive failure indicators 0000000000 00000000000 0000000000 ooo 00000000000000 S N 8 E 2 Ax D e 00000000000000 000000000 000 ooo o OOOOOOOOOOOOOOOOD 9000000000000000 Figure 27 Server Chassis SC5250 E SCSI Backplane 5 10 2 SCSI Hot Swap Backplane Specifications The server chassis SC5250 E hot swap SCSI backplane is an embedded application subsystem that does the following during normal operation e Responds to SAF TE messages transmitted to the backplane via the SCSI bus e Monitors the temperature on the backplane and reports a warning or critical error if outside programmed limits if the s
8. Intel Server Chassis SC5100 and SC5200 External SCSI Cable Install Guide SCSI Accessed Fault Tolerant Enclosures Specification Revision 1 00 SSI Entry Level Electronics Bay Specification Version 3 0 Advance Technology Extended ATX Specification Revision 2 03 ANSI IEEE STD C62 45 1992 Environmental Standards Handbook Revision 1 02 63 Intel order number C32881 001
9. and independent PCI buses Segment A 32 bit 33 MHz 5 V P32 A with four embedded devices e 2D 3D graphics controller ATI Rage XL with 8 MB of SDRAM e One Intel 82550PM 10 100 Fast Ethernet controller e One Intel 82540EM gigabit Ethernet controller e Two PCI slots capable of supporting full length PCI add in cards Segment B PCI X 64 bit 66MHz 3 3 V P64 B with the following configuration e Two PCI slots capable of supporting full length PCI add in cards Segment C PCI X 64 bit 133 MHz 3 3 V P64 C with the following device e One PCI slot capable of supporting full length PCI add in cards LPC Low Pin Count bus segment with two embedded devices Super I O controller chip providing all PC compatible I O floppy serial keyboard mouse as well as integrated hardware monitoring Flash ROM device for system BIOS Intel N82802AC 8 megabit Flash ROM Three external Universal Serial Bus USB ports with an additional internal header providing up to two optional USB ports for front panel support Two USB ports are supported on the SC5250 E chassis Two IDE connectors supporting up to four ATA 100 compatible devices Support for up to five system fans and two processor fans SSI compliant connectors for SSI interface support front panel and power connectors 44 Revision 1 02 Intel order number C32881 001 Intel amp Entry Server Chassis SC5250 E Compatible Intel amp Server Boards 9 4 Intel Server Board SE
10. device could void the user s authority to operate the equipment The customer is responsible for ensuring compliance of the modified product Only peripherals computer input output devices terminals printers etc that comply with FCC Class B limits may be attached to this computer product Operation with noncompliant peripherals is likely to result in interference to radio and TV reception All cables used to connect to peripherals must be shielded and grounded Operation with cables connected to peripherals that are not shielded and grounded may result in interference to radio and TV reception 10 4 2 FCC Verification Statement This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation For questions related to the EMC performance of this product contact Intel Corporation 5200 N E Elam Young Parkway Hillsboro OR 97124 6497 Phone 1 800 INTEL4U or 1 800 628 8686 10 4 3 ICES 003 Canada Cet appareil num rique respecte les limites bruits radio lectriques applicables aux appareils num riques de Classe A prescrites dans la norme sur le mat riel brouilleur Appareils Num riques NMB 003 dict e par le Ministre Canadien des Communications English translation of the notice above This digital appar
11. ea eai 14 Figure 14 Install Retention Brackets see ees Ee es Gee RE AE Se ER EE RR Ge ee Ge Ee Ge Se ER ee Ge enin NEEN 15 Figure 15 Install CPU Heatsink units one per proceSSOF ese ee ee ee ee ee ee ee ee ee 16 Figure 16 Install CPU metal clips one set per DroceSSOF ee ee ee ee ee ee ee ee 16 Figure 17 GPU Air Duct Folding ert dst sect Res AK ea aa Ge DE GEEN abet eben Ee 17 Figure 18 Attach CPU Air Duct to Rear system Fan 18 Figure 19 Install Rear system Fan assembly to System Chassis 19 Figure 20 Installing Front spacers for the Fixed Hard Drive Bay 20 Figure 21 Reinstalling Fan with Front spacers to the Fixed Hard Drive Bay 20 Figure 22 Securing Fan with Front spacers to the Fixed Hard Drive Day 21 Figure 23 Drive Bay Locations for Server Chassis SCS250 E esse ees Re ee ee 22 Figure 24 Hot swap Drive Bay Front Isometric View 26 Figure 25 Hot swap Drive Bay Rear Isometric View 26 Figure 26 Drive Carrier with Air Baffle Installed see ee EE ee EA AE SR Re Ke ee ee Ek ee 27 Figure 27 Server Chassis SC5250 E SCSI Backolane ie ee RR ee ee ee 28 Figure 28 Server Chassis SC5250 E SAF TE Board esse ees ees se ee ee ee ee ee ee Re ee ee 29 Figure 29 Hot swap Drive Bay Front Isometric View 34 Revision 1 02 vi Intel order number C32881 001 List of Figures Intel Entry Server Chassis SC5250 E Figure 30 Figure 31 Figure 32 Figure 33 Figu
12. ee ee ee ee ee ee ee ee ee ee ee entente 59 EI TR AE EE RE EE RE EE ER 61 Relerence Doeamerts ek EA elke Ke WO De CE EE RANA E we le Aas EN ee 63 VM Revision 1 02 Intel order number C32881 001 Intel amp Entry Server Chassis SC5250 E List of Figures List of Figures Figure 1 ATX 2 03 l O AB SMUG oneri teo edat eia be ee Ee bo Ee eate Ge Lote t s 3 Figure 2 Front Closed View of Server Chassis GCDZD0DE 4 Figure 3 Rear Closed View of Server Chassis GCHhZbOE 5 Figure 4 Front Internal View for Server Chassis SC5250 E eie ee ee ee ee ee ee ee ee ee ee 6 Figure 5 Rear Internal View for Server Chassis SC5250 E ee ee ee ee ee ee ee ee ee ee 6 Figure 6 450 W EPS 2 0 Power SUD EE 8 Figure 7 Cooling Fan ConfIgUreatiori x acier eee doe tete debel ieu e EEN 10 Figure 8 Processor Wind Tunnel Illustration with Intel Xeon Processor with 400MHz System Een WEE 11 Figure 9 Processor Wind Tunnel Illustration with Intel Xeon Processor with 533MHz System Bus Speed EE 12 Figure 10 Remove wind Tunnel for your Intel Server Board SE7505VB2 esse esse ees ee 13 Figure 11 Remove the Retention Mechanism if present on your Intel Server Board SE TOOSVB2 ER Ed m 14 Figure 12 Remove Retention Mechanism when present on your Intel Server Board SE7505VB214 Figure 13 Remove the old contaminated thermal grease letter A in the following figure from the top of the Processor srera ee ee ee ee ee ee ee nennen nnn nsn a
13. es E a UE CAR E UR Ea nu CRX VA FA ENS UN EVE Da VY a RA 39 X NES No id eu mL N EE OE EE EN 39 8 2 Chassis Internal Cables ie AA RR AR EA RR EA ER ER ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee ee 39 8 2 1 EBront Panel cable paces wit ete pergo de dep ate Raines 39 822 USB CAD 6 si tM Le 39 8 2 3 Fan Connectors dd er e ede ties D ERR RE Rr E cR e etie a ee ites 39 8 3 Server Board Internal Cables sss eee 39 E EE 40 8 4 1 ICMB Interface Card Cable EE Ge ee ee ee emen enne 40 8 4 2 External SCSI Cable RR ER ER ER ER EE ee nennen nennen nnne nn ee nennen nnn 40 8 5 VO Panel Connectors ie se RR ER ER ER ER EE ee ee ee ee ee ee ee ee ee ee ee nnns 40 9 Compatible Intel Server Boards EEN ee Re ee ee Re tans 41 9 1 Intel Server Board SE7501BR2 Feature Get 41 9 2 Intel Server Board SE7500CW2 Feature Get 43 9 3 Intel Server Board SE7501CW2 Feature Get 44 9 4 Intel Server Board SE7505VB2 Feature Set 45 9 5 Intel Server Board S845WD1 E Feature Set ee RR RR RR EA RR RR ek ee RR ee ee Re ee 46 9 6 Intel Entry Server Board S875WP1 E Feature Get 47 Revision 1 02 v Intel order number C32881 001 Table of Contents Intel amp Entry Server Chassis SC5250 E 9 7 Intel Entry Server Board SE7210TP1 E Feature Get 48 10 Product Regulatory Compliance sees see RR RE RE EE RE RR RR RE EER nennen KERE Rea 50 10 1 Product Safety lol El Le 50 10 2 Product EMC Compliance es
14. infringement of any patent copyright or other intellectual property right Intel products are not intended for use in medical life saving or life sustaining applications Intel may make changes to specifications and product descriptions at any time without notice Designers must not rely on the absence or characteristics of any features or instructions marked reserved or undefined Intel reserves these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them The Intel amp Entry Server Chassis SC5250 E may contain design defects or errors known as errata which may cause the product to deviate from published specifications Current characterized errata are available on request Intel Pentium Itanium and Xeon are trademarks or registered trademarks of Intel Corporation Other brands and names may be claimed as the property of others Copyright Intel Corporation 2003 Revision 1 02 iii Intel order number C32881 001 Table of Contents Intel amp Entry Server Chassis SC5250 E Table of Contents 2 3 4 5 MILII IPM RR N N 2 2 1 EE Ee 2 2 2 Front RE 2 249 SSeCUIIUy oid e cuc eb OU aide c te M ue ii uia Heute 2 2A ME Qe 3 29 CHASSIS VIC em 4 Chassis Power Subsystem ses es bee dee de de we dee ee Ek GN ke ey Ro Re ed ee ee ke ke sd ee 7 3 1 450 Watt EPS 2 0 Power SupplY ie
15. memory with two 184 pin DDR SDRAM Dual Inline Memory Module DIMM sockets DDR400 to run DDR400 memory at full speed requires an Intel Pentium 4 processor with 800 MHz front side bus FSB frequency DDR333 to run DDR333 memory at full speed requires an Intel Pentium 4 processor with 533 MHz FSB frequency DDR333 memory will run at 320 MHz frequency when using an Intel Pentium 4 processor with 800 MHz FSB frequency DDR266 DDR266 memory may only be used with an Intel Pentium 4 processor with 400 MHz or 533 MHz FSB frequency only One AGP bus with AGP connector One AGP connector supporting 1 5 V 8X AGP cards One independent PCI bus 32 bit 33 MHz 5 V with three PCI connectors and three embedded devices 2D 3D graphics controller ATI Rage XL Video Controller with 8 MB of SDRAM Accelerated Graphics Port AGP connector providing AGP 8x support Optional SATA controller on S875WP1LX Promise Technology PDC20319 LPC Low Pin Count bus segment with one embedded device SMSC LPC47M102 LPC Bus I O controller controller chip providing all PC compatible I O floppy serial keyboard mouse X Bus segment with one embedded device Flash ROM device for system BIOS Intel 32 megabit 28F320C3 Flash ROM Four external USB ports on the back panel with an additional internal header which provides support for an optional two USB ports for front panel support total possible six USB ports One serial port and one ser
16. not supported 4 The BIOS is responsible for setting the mode PCI or PCI X and bus speed for the two segments provided by the P64H2 The actual bus mode speed will be determined by the least capable card installed on that bus The BIOS will program the bus at 133MHz with one slot populated and 100MHz when two slots are populated 5 PCI slot 1 is designed to support a 2 slot PCI riser card Segment C will run at a maximum of 100 MHz if a riser card is used 8 Serial B is the designated Server Management serial port 42 Revision 1 02 Intel order number C32881 001 Intel amp Entry Server Chassis SC5250 E Compatible Intel amp Server Boards 9 2 Intel Server Board SE7500CW2 Feature Set The server board SE7500CW2 support the following feature set Dual Intel Xeon processors using the 603 pin INT mPGA package 400 MHz Front Side Bus Intel amp E7500 server chipset MCH memory controller P64H2 64 bit VO Hub ICH3 S I O controller FWH Firmware Hub Support for up to four DDR200 or DDR266 compliant ECC DDR DIMMs providing up to 4GB of memory support Three separate and independent PCI buses Segment A 32 bit 33 MHz 5 V P32 A with four embedded devices 2D 3D graphics controller ATI Rage XL with 8 MB of SDRAM Two Intel 10 100 82550PM Fast Ethernet Controllers ATA 100 RAID controller Promise Technology PDC20267 Two PCI slots capable of supporting full length PCI add in cards Segment B PCI X 64 bit 66MHz
17. removes the drive from service and sends a spin down SCSI command to the drive This decreases the likelihood that the drive will be damaged during removal from the hot swap drive bay When a new drive is inserted the power control waits a small amount of time for the drive to be fully seated and then applies power with a controlled power ramp e If the system power is on the LVD SE SCSI backplane immediately powers off a drive slot when it detects that a drive has been removed This prevents possible damage to the drive when it is partially removed and re inserted while full power is available and disruption of the entire SCSI array from possible sags in supply voltage and resultant current spikes 5 6 FET Short Protection The Field Effect Transistor FET short protection circuit is useful to protect both 12 volt and 5 volt power control FETs located on LVD SE SCSI backplane 5 7 Device SCSI ID Each device on a SCSI bus must have a unique SCSI ID The 5 x 1 0 LVD SE SCSI backplane device SCSI ID is dependent on whether it is configured as a primary or a secondary backplane This configuration is defined by the logic of pin 1 on the PC connector J2A1 Note The server chassis SC5250 E will only support a single backplane therefore it will always be identified as primary on the DC bus Table 3 SCSI ID Assignments D yice SCSI ID as Primary Backplane SCSI ID as Secondary Backplane VC connector J2A1 pin1 1 IC connector J2A1 pi
18. the old contaminated thermal grease letter A in the following figure from the top of the processor 14 Revision 1 02 Intel order number C32881 001 Intel amp Entry Server Chassis SC5250 E System Cooling 4 6 Installing the Intel APTWKTCOOLKIT for SE7505VB2 Intel Server Board The Workstation Cooling Kit was designed to work with the Intel Server Board SE7505VB2 and Intel Server Chassis SC5250 E to dramatically reduce system level acoustics making it an effective solution when acoustics is a concern Intel Part Number APTWKTCOOLKIT Intel MM 858795 Please refer to Intel WorkStation Cooling Kit User s Guide for complete installation instructions Order Number C55113 001 Rev 2 Do not install the Intel amp Workstation Acoustic Kit in systems with only one processor This kit is designed for two processor systems If you only have one processor installed the large opening left by the second processor and heat sink will reduce the airflow through the single processor s heat sink and may cause the system to overheat The following items are included in the kit e Two heat sinks e A flexible air duct e Four plastic retention mechanisms two per heat sink e Eight coarse thread screws two per retention mechanism e Four metal retention clips two per heat sink for 400 Mhz FSB processors e Four metal retention clips two per heat sink for 533 Mhz FSB processors e Four nylon rivets for air duct attachment to rear system fan e
19. 3 3 V P64 B with the following configuration Two PCI slots capable of supporting full length PCI add in cards Segment C PCI X 64 bit 133 MHz 3 3 V P64 C with the following device One PCI slot capable of supporting full length PCI add in cards LPC Low Pin Count bus segment with two embedded devices Super I O controller chip providing all PC compatible I O floppy serial keyboard mouse as well as integrated hardware monitoring Flash ROM device for system BIOS Intel 8Mbit N82802AC Flash ROM Three external Universal Serial Bus USB ports with an additional internal header providing one optional USB ports for front panel support Two IDE connectors supporting up to four ATA 100 compatible devices Support for up to four system fans and two processor fans SSI compliant connectors for SSI interface support front panel and power connectors Revision 1 02 43 Intel order number C32881 001 Compatible Intel amp Server Boards Intel Entry Server Chassis SC5250 E 9 3 Intel amp Server Board SE7501CW2 Feature Set The server board SE7501CW2 support the following feature set Dual Intel Xeon processors using the 603 pin INT mPGA package and 604 pin FCPGA package 533 MHz front side bus Intel E7501 server chipset MCH memory controller P64H2 64 bit VO hub ICH3 S I O controller FWH firmware hub Support for up to four DDR200 or DDR266 compliant ECC DDR DIMMs providing up to 8GB of memory support Three separate
20. 33 MHz memory at full speed requires an Intel Pentium 4 processor with 533 MHz system bus frequency Note PC2700 333 MHZ memory will run at 320 MHz frequency when using an Intel Pentium 4 processor with 800 MHz system bus frequency e PC2100 266 MHZ PC2100 266 MHZ memory may only be used with an Intel Pentium 4 processor with 400 MHz or 533 MHz system bus frequency only o Intel 82547GI Platform LAN Connect PLC device for 10 100 1000 Mbits sec Ethernet LAN connectivity o Intel 82551QM device for 10 100 Mbits sec Ethernet LAN connectivity 48 Revision 1 02 Intel order number C32881 001 Intel amp Entry Server Chassis SC5250 E Compatible Intel amp Server Boards O O 0 0 O Two independent PCI buses one 32 bit 33 MHz 5 V one 64 bit 66 MHz 3 3V with four PCI connectors and two embedded devices e Three PCI X 64 bit PCI slots e One 32 bit PCI slot e Integrated 2D 3D graphics controller ATI Rage XL Video Controller with 8 MB of SDRAM e Optional single channel Ultra 320 SCSI controller on SE7210TP1S CSI Adaptec 7901 LPC Low Pin Count bus segment with one embedded device Winbond W83627HF AW LPC Bus I O controller chip providing all PC compatible I O floppy serial keyboard and mouse Three external USB 2 0 ports on the back panel with an additional internal header which provides support for one additional USB port for front panel support four total possible USB 2 0 ports One serial port and one serial por
21. 34 Revision 1 02 Intel order number C32881 001 Intel amp Entry Server Chassis SC5250 E System Peripheral Bays Figure 31 Drive Carrier with Air Baffle Installed 7 6 Hot Swap Drive Bay Electronics The hot swap SATA backplane board set supports the following features e Hot swapping of SATA drives which allows connection of SATA devices while the system is powered on e Management and monitoring functions conforming to the SATA 1 0 Specification 7 6 1 SATA Board Layout The following figure shows the layout of components and connectors on the hot swap SATA backplane printed circuit board set Note that many of the sites are not populated and do not affect the functionality of the SATA backplane Revision 1 02 35 Intel order number C32881 001 System Peripheral Bays 36 Intel Entry Server Chassis SC5250 E Figure 32 Intel amp Server Chassis SC5200 and SC5250 E SATA Backplane Table 9 Connector References Description Power Connector 2 Host Side Drive 0 Host Side Drive 1 Host Side Drive 2 J4A2 J4A2 J4A1 This connector is shared for both Drive 0 and Drive 1 Drive 0 is the one furthest from the peripheral connector board PCB This connector is shared for both Drive 0 and Drive 1 Drive 1 is the one closest to the PCB This connector is shared for both Drive 2 and Drive 3 Drive 2 is the one furthest from the PCB Intel order number C32881 001 Revision 1 02 Intel amp En
22. 4 1 ICMB Interface Card Cable One 5 pin ICMB cable connects the server board to the ICMB interface card mounted on the chassis rear panel or add in card slot Included in the ICMB Interface Card Kit AXX2ICMBKIT 8 4 2 External SCSI Cable One 68 pin SCSI cable connects the server board or add in SCSI card to the panel that mounts to the back of the chassis see Figure AXXEXTSCSICBL 8 5 VO Panel Connectors The server chassis SC5250 E chassis provides an ATX 2 03 and SSI E bay 3 0 compliant VO aperture for the backside VO The specific panel used will be provided in the boxed server board kit The following are typical panel connections e PS 2 keyboard connector e PS 2 mouse connector e 9 pin serial port s e 25 pin parallel port e USB port s e 15 pin video port e Ethernet RJ 45 connector s 40 Revision 1 02 Intel order number C32881 001 Intel amp Entry Server Chassis SC5250 E Compatible Intel amp Server Boards 9 Compatible Intel Server Boards The Intel Server Chassis SC5250 E supports the following Intel amp server boards Intel amp Server Board SE7501BR2 Intel amp Server Board SE7500CW2 Intel amp Server Board SE7501CW2 Intel amp Server Boards SE7505VB2 Intel Server Board S845WD1 E Intel Server Board S875WP1 E Intel Server Board SE7210TP 1 E The features of these boards are provided in the sections below Future server boards may also be targeted for the server chassis SC5250 E f
23. 7505VB2 Feature Set Major features of the SE7505VB2 server board include the following e Dual Intel Xeon processor support e Embedded VRM e Intel E7505 chipset e Support for four DDR266 registered ECC SDRAM DIMMs e AGP 8x Pro 50 connector e 32 bit 33 MHz 5V keyed PCI segment with two expansion connectors and three embedded devices One PCI NIC Intel amp 82550PM Fast Ethernet Controller 3D 2D graphics accelerator ATI Rage XL 8 MB SDRAM Video Controller Silicon Image Sil3112A dual port Serial ATA controller e 64 bit 66 MHz 3 3V PCI segment with one expansion connector and one embedded device One PCI network interface controller Intel 82540EM Gbit Ethernet Controller e LPC bus segment with two embedded devices Super UO controller chip providing all PC compatible VO floppy parallel serial keyboard mouse and hardware monitoring 1MB Firmware Hub for system BIOS e Four Universal Serial Bus USB ports e Two IDE connectors supporting two ATA 33 66 100 compatible devices e Support SMBus e Server board SE7505VB2 has following connectors and switches Serial x 2 Parallel USB x 4 keyboard mouse video IPMB x 1 Floppy IDE x 2 SATA x 2 LAN x 2 one 100 10Base T one 1Gbit x 1 Dump NMI switch DC on off switch Sleep switch Reset switch and ID switch rack See the Intel Server Board SE7505VB2 TPS on the support intel com website for more detail Revision 1 02 45 Intel order num
24. 901 wide Ultra 320 SCSI Controller3 o Zero Channel RAID ZCR support Also known as modular M ROMB Slot4 Segment C 64 bit 133 MHz 3 3 V Full length PCI P64 C supporting the following configuration o Two slots 64 bit 100MHz PCI X4 Slots PCI X Slot 15 and Slot 2 e LPC Low Pin Count bus segment with two embedded devices Baseboard Management Controller BMC providing monitoring alerting and logging of critical system information obtained from embedded sensors on server board Super HO controller chip providing all PC compatible I O floppy serial parallel keyboard mouse X Bus segment with one embedded device o Flash ROM device for system BIOS Intel 32 megabit 28F320C3 Flash ROM e Three external Universal Serial Bus USB ports on the rear of the board with an additional internal header that provides two optional USB ports for front panel support e Two serial ports One external serial port Serial A on the back edge of the board and one internal header providing an optional Serial B port e Two IDE connectors supporting up to four ATA 100 compatible devices e Six two for redundancy multi speed system fans and two single speed CPU fans e Multiple server management headers providing on board interconnects to the board s server management features e SSI EEB3 0 compliant board form factor the board size is 12 inch by 13 inch 2 NIC1 is the designated Server Management NIC 3 Single Ended Mode
25. AD T ee m e om eoo ege ge Jego Vele Yolo Jele TP00572 Figure 22 Securing Fan with Front spacers to the Fixed Hard Drive Bay Revision 1 02 21 Intel order number C32881 001 System Peripheral Bays Intel Entry Server Chassis SC5250 E 5 System Peripheral Bays 5 1 3 5 Peripheral Drive Bay The Intel Server Chassis SC5250 E provides for the installation of a 3 5 inch peripheral such as a floppy drive below the 5 25 inch peripheral bays The bezel must be removed prior to floppy drive installation When a floppy drive is not installed a snap in EMI shield must be in place to ensure regulatory compliance Cosmetic plastic filler is provided to snap into the bezel The 3 5 bay is designed so that screws are only required on the left side of the chassis as indicated in the figure below On the right side of the chassis two protrusions in the sheet metal hold the drive in place TPID Figure 23 Drive Bay Locations for Server Chassis SC5250 E 22 Revision 1 02 Intel order number C32881 001 Intel amp Entry Server Chassis SC5250 E System Peripheral Bays 5 2 5 25 Peripheral Drive Bays The SC5250 E chassis supports two half height or one full height 5 25 inch removable media peripheral device such as a magnetic optical disk CD ROM or tape drive These peripherals can be up to 9 inches 228 6mm deep As a guideline the maximum recommended power per device is 18W Thermal performance of specific device
26. Four plastic spacers e Eight fine thread screws two per spacer Install the Retention Brackets two per heat sink that came with your Intel amp Workstation Acoustic Kit Use the screws that came with the kit Note that all the Retention Brackets are identical om 7 TP00498 Figure 14 Install Retention Brackets Revision 1 02 15 Intel order number C32881 001 System Cooling Intel amp Entry Server Chassis SC5250 E RENE SR M AUER Lu 1 TPOO499 TPOO499 Figure 15 Install CPU Heatsink units one per processor Position the metal clips that came with your Intel Workstation Acoustic Kit as shown in the following figure 16 Make sure that the center tab letter B in the following figure engages the slot in the heat sink base number 1in the figure Repeat Steps 4 6 for second retention clip TP00575 Figure 16 Install CPU metal clips one set per processor 16 Revision 1 02 Intel order number C32881 001 Intel amp Entry Server Chassis SC5250 E System Cooling 4 7 Configuring CPU Duct Fan Assembly the Intel amp APTWKTCOOLKIT for SE7505VB2 Intel amp Server Board Fold the Air Duct that came with your Intel Workstation Acoustic Kit as illustrated in figure 17 Make sure that the black marker lines are positioned towards the inside of the Air Duct Begin with fold 1 and proceed through fold 7 Completed Air Duct should look like left and right views see 8 and 9 in the following fi
27. Intel Entry Server Chassis C5250 E Technical Product Specification Intel order number C32881 001 Revision 1 02 February 2004 Enterprise Platforms and Services Marketing Revision History Intel Entry Server Chassis SC5250 E Revision History Revision Modifications Number 10 07 02 01 Initial review copy 0 1 11 25 02 Initial feedback incorporated 12 10 02 Engineering and Technical Marketing changes incorporated to document 2 3 02 Reviewed for grammar replaced edited drawings 3 112 03 Added MTBF information and part numbers 5 30 03 1 01 Added SATA Upgrade Kit Information and support for Intel Server Board SE7500CW2 Intel Server Board SE7501CW2 Intel Server Board S845WD1 E and Intel Server Board S875WP1 2 15 04 1 02 Added APTWKTCOOLKIT information for SE7505VB2 and SE7210TP1E information ii Revision 1 02 Intel order number C32881 001 Intel amp Entry Server Chassis SC5250 E Disclaimers Disclaimers Information in this document is provided in connection with Intel products No license express or implied by estoppel or otherwise to any intellectual property rights is granted by this document Except as provided in Intel s Terms and Conditions of Sale for such products Intel assumes no liability whatsoever and Intel disclaims any express or implied warranty relating to sale and or use of Intel products including liability or warranties relating to fitness for a particular purpose merchantability or
28. Intel Server Chassis SC5100 and SC5200 The backplane is an LVD SE SCSI design which provides support for SCSI devices using Low Voltage Differential Signaling as well as support for older SE SCSI devices Ultra 160 and older The backplane has a connector to accommodate a SAF TE controller on an add in card The backplane supports five 1 inch hot swap SCA 2 drives when mounted in the docking drive carrier 54 SCSI Multi Mode Termination The multi mode terminators provide SCSI 4 compliant termination for the backplane These terminators provide termination in both SE modes and LVD mode Installing a single SE drive forces all installed drives to run in the SE termination mode on the SCSI bus Revision 1 02 23 Intel order number C32881 001 System Peripheral Bays Intel Entry Server Chassis SC5250 E 5 5 SCSI Interface The SCSI interface on the server chassis SC5250 E LVD SE SCSI backplane provides the link between the SCSI bus and the microcontroller containing the intelligence for the server chassis SC5250 E LVD SE SCSI backplane This interface allows the microcontroller to respond as a SCSI target to implement the SAF TE protocol Power control on the server chassis SC5250 E LVD SE SCSI backplane supports e Spin down of a drive when failure is detected and reported using enclosure services messages via the SCSI bus An application or RAID controller detects a drive related problem that indicates a data risk In response it
29. al compliance to Safety or EMC requirements Refer to the system product guide for details on regulatory information Revision 1 02 53 Intel order number C32881 001 Environmental Limits Intel amp Entry Server Chassis SC5250 E 11 Environmental Limits 11 1 System Office Environment Table 11 System Office Environment Summary Operating Temperature 50C to 350C with the maximum rate of change not to exceed 100C per hour Non Operating Temperature 400C to 700C Non Operating Humidity 95 non condensing 300C 50 dBA in a typical office ambient temperature 18 25C Operating Shock No errors with a half sine wave shock of 2G with 11 millisecond duration Package Shock Operational after a free fall 18 24 inch depending on the weight 15kV per Intel Environmental Test Specification 11 2 System Environmental Testing The system will be tested per the Environmental Standards Handbook Intel Doc 662394 05 These tests shall include e Temperature Operating and Non Operating e Humidity Non Operating e Packaged Shock e Packaged and Unpackaged Vibration e AC Voltage Frequency and Source Interrupt e AC Surge e Acoustics e Electrostatic Discharge ESD e EMC Radiated Investigation 54 Revision 1 02 Intel order number C32881 001 Intel amp Entry Server Chassis SC5250 E Reliability Serviceability and Availability 12 Reliability Serviceability and Availability 12 1 MTBF Calculated Mean Time Between Fai
30. amily 9 1 Intel amp Server Board SE7501BR2 Feature Set The server board SE7501BR2 supports the following feature set Dual Intel Xeon processors with 512KB L2 Cache in a FC mPGA2P or INT3 mPGA package 533 MHz Front Side Bus backwards compatible to 400MHz 64 bit 100 MHz 3 3V PCI X segment with two expansion connector Four Universal Serial Bus USB ports Two IDE connectors supporting two ATA 33 66 100 compatible devices Intel amp chipset Intel E7501 memory controller hub MCH Intel 82870P2 PCI PCI X 64 bit Hub2 P64H2 PCI PCI X controller hub Intel 82801CA VO Controller Hub3 ICH3 S VO controller hub Support for four DDR266 compliant registered ECC DDR DIMMs providing up to 8 GB of memory Three separate and independent PCI buses Segment A 32 bit 33 MHz 5 V Full length PCI P32 A with three embedded devices o Two slots 32 bit 33MHz PCI Slots PCI Slot 5 and Slot 6 o 2D 3D graphics controller ATI Rage XL Video Controller with 8 MB of SDRAM o Intel 82540EM 10 100 1000 Gigabit Ethernet Controller NIC2 Revision 1 02 41 Intel order number C32881 001 Compatible Intel amp Server Boards Intel Entry Server Chassis SC5250 E o Intel 82550PM 10 100 Fast Ethernet Controller NIC12 Segment B 64 bit 133 MHz 3 3 V full length PCI P64 B supporting the following configuration o Two slots 64 bit 100MHz PCI X Slots PCI X Slot 3 and Slot 4 o Single channel Adaptec AIC 7
31. ard drives must be verified to ensure compliance to the drive manufacturer s specifications A compatibility list of supported Intel amp server boards for the Server Chassis SC5200 and Server Chassis SC5250 E is available on support intel com URL http support intel com An optional hot swap upgrade drive bay assembly ASATAHSDB is available for the Server Chassis SC5200 and Server Chassis SC5250 E It should be mounted in place of the middle three 5 25 inch drive trays of the base non redundant chassis models For the redundant power models the upgrade accessory should be installed in the lower three 5 25 inch drive trays to bring the total number of available hot swap SATA drives to eight Refer to the Inte Server Chassis SC5200 and SC5250 E Hot swap Bay Upgrade Kit for installation instructions 7 2 SATA Interface The SATA interface for the SATA backplane provides the link between the SATA bus and the microcontroller T 3 Device SATA ID Each device on a SATA bus must have a unique ID The 4 x 1 0 backplane device ID is dependent on the connection to the controller The recommended configuration for the RAID Controller SRCS14L is listed in the following table It is important that the user follow this recommendation to ensure that the drive activity and fault LEDs correspond to the correct drive It is not critical to follow a specific connection scheme if a different SATA controller is used as other controllers do not provide ac
32. assis Management Bus LVDS Low voltage differential SCSI MTBF Mean Time Between Failures MTTR Mean Time to Repair LT C B C l S G D T U H T C C E M N D C 2 D O IS LA E P L L Revision 1 02 61 Intel order number C32881 001 Glossary Intel Entry Server Chassis SC5250 E OEM Original Equipment Manufacturer Server System Infrastructure Organization which defines and promotes specifications for the server market Wake on LAN 62 Revision 1 02 Intel order number C32881 001 Intel amp Entry Server Chassis SC5250 E Reference Documents Reference Documents Refer to the following documents for additional information Intel Server Board SE7505VB2 Technical Product Specification Intel Server Board SE7501BR2 Technical Product Specification Intel Server Board SE7500CW2 Technical Product Specification Intel Server Board SE7501CW2 Technical Product Specification Intel Server Board S845WD1 E Technical Product Specification Intel Entry Server Board S875WP1 E Technical Product Specification Intel Entry Server Board SE7210TP1 E Technical Product Specification C5100 Low Voltage Differential Single Ended SCSI Backplane EPS Server Chassis SC5100 and SC5200 and Server Platform SRSH4 and SPSH4 Hot Swap Controller EPS 450 W EPS 1 0 Power Supply Module Specification Intel Server Chassis SC5250 E Subassembly Product Guide Intel Server Chassis SC5250 E Hot Swap Bay Upgrade Kit
33. atus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the interference causing equipment standard entitled Digital Apparatus ICES 003 of the Canadian Department of Communications 10 4 4 Europe CE Declaration of Conformity This product has been tested in accordance too and complies with the Low Voltage Directive 73 23 EEC and EMC Directive 89 336 EEC The product has been marked with the CE Mark to illustrate its compliance 52 Revision 1 02 Intel order number C32881 001 Intel Entry Server Chassis SC5250 E Product Regulatory Compliance 10 4 5 Japan EMC Compatibility Electromagnetic Compatibility Notices International COMB FRUBRESERESAERNBRS VCCI ORE CESI DVSRAPHERHEE CT OBBETXRURSCC ERT S CBR HESVNSROTCEMHBVOET COMSICIAPAAD ROEM RES SKIBRANATEMHBVET English translation of the notice above This is a Class A product based on the standard of the Voluntary Control Council for Interference VCCI from Information Technology Equipment If this is used near a radio or television receiver in a domestic environment it may cause radio interference Install and use the equipment according to the instruction manual 10 4 6 BSMI Taiwan The BSMI Certification number and the following warning are located on the product safety label which is located on the bottom side of the chassis Installation of the Intel Workstation Acoustic Kit does not effect origin
34. ber C32881 001 Compatible Intel amp Server Boards Intel Entry Server Chassis SC5250 E 9 5 Intel amp Server Board S845WD1 E Feature Set The server board S845WD1 E provides an embedded ATA 100 Valu Raid interface and supports the following feature set Support for an Intel Celeron processor in a uPGA478 socket Support for an Intel Pentium 4 processor in a uPGA478 socket 400 533 MHz System Bus Intel 845E chipset Intel 82845E Memory Controller Hub MCH Intel 82801BA VO Controller Hub ICH2 Intel 82802AB 4 Megabit Firmware Hub FWH Support for single sided or double sided DIMMs DDR 200 and DDR 266 providing up to 2 GB system memory with two 184 pin DDR SDRAM Dual Inline Memory Module DIMM sockets One AGP bus with AGP connector One AGP connector supporting 1 5 V 4X AGP cards One independent PCI bus 32 bit 33 MHz 5 V with three PCI connectors and four embedded devices 2D 3D graphics controller ATI Rage XL Video Controller with 2 MB of SDRAM Two Intel10 100 82550PM Fast Ethernet Controllers ATA 100 controller Promise Technology PDC20267 LP Low Pin Count bus segment with one embedded device SMSC LPC47M102 LPC Bus I O controller controller chip providing all PC compatible UO floppy serial keyboard mouse X Bus segment with one embedded device Flash ROM device for system BIOS Intel 32 megabit 28F320C3 Flash ROM Two external Universal Serial Bus USB ports with a
35. e chassis monitoring and management as specified in the SCS Accessed Fault Tolerant Enclosures Specification SAF TE Revision 1 0 The SAF TE specified features supported by the hot swap SCSI backplane include but are not limited to monitoring the SCSI bus for enclosure services messages and acting on them appropriately Examples of such messages include activate a drive fault indicator power down a drive that has failed and report backplane temperature The SAF TE intelligent agent acts as a proxy for dumb DC devices during intra chassis communications These devices have no bus mastering capability 5 12 Serial ATA SATA Hardware Overview Up to two SATA backplanes supporting up to eight drives can be mounted in a Server Chassis SC5200 if a SATA controller is installed One SATA backplane can be mounted in the Server Chassis SC5250 E Each SATA backplane supports the connection of up to four SATA drives When two SATA backplanes are mounted one is designated the Primary SATA Backplane and the second is designated the Secondary SATA Backplane These terms are used to be consistent with other backplanes in other server system products 30 Revision 1 02 Intel order number C32881 001 Intel amp Entry Server Chassis SC5250 E Functional Specifications 6 Functional Specifications The hot swap backplane is responsible for the following system functions 6 1 Drive Fault Light Control SATA Specification revisio
36. e ee ese sesse se ee ee ee ee ee ee ee Re ee ee ee de ee ee ee ee ee ee 54 Table 12 MTBF Calculations esses nennen nennen nne ee ee ee ee nnne 55 Table 13 Maximum Maintenance Procedure Times se ee Ee RR ER ER ee Re ee Re Re ee Re ee ee 95 Revision 1 02 ix Intel order number C32881 001 Intel amp Entry Server Chassis SC5250 E Introduction 1 Introduction This specification details the feature set of the Intel Server Chassis SC5250 E an entry level server chassis designed for Intel server board products The server chassis SC5250 E is low cost and allows utilization of multiple platforms and configurations The server chassis SC5250 E KPTBASE450 is designed to address the value server market It includes a single 450W power factor correction PFC power supply and supports four non hot swap hard drives One tachometer fan that is mounted in front of the fixed drive cage and one that is mounted at the rear of the chassis provide Main chassis cooling This chassis is currently compatible with Intel amp Server Board SE7501BR2 Intel amp Server Board SE7500CW2 Intel amp Server Board SE7501CW2 Intel amp Server Boards SE7505VB2 Intel amp Server Board S845WD1 E Intel Server Board S875WP1 E and Intel Server Board SE7210TP1 E Two 5 25 inch half height drive bays are available for peripherals such as CD ROM and tape drives and a removable access cover provides entry to the interior of the chassis The rea
37. e figure below demonstrates removing the fan from the standard drive bay and placing it onto the hot swap drive bay Figure 34 Replacing System Fan from IDE Drive Carrier to the SCSI Drive Carrier 56 Revision 1 02 Intel order number C32881 001 Intel amp Entry Server Chassis SC5250 E Upgradeability 13 2 External SCSI Adapter Cable Product Code AXXEXTSCSICBL This 68 pin LVD SCSI cable allows an internal SCSI connection from the motherboard to be routed to the ICMB SCSI knockout at the rear of the chassis Figure 35 External SCSI Adapter Cable Detail Revision 1 02 57 Intel order number C32881 001 Upgradeability Intel amp Entry Server Chassis SC5250 E 13 3 SATA Hot swap Drive Bay Upgrade Product Code ASATAHSDB The kit includes a SATA hot swap drive bay with mounting hardware Four SATA cables SATA connection ID Label and a User s Configuration Guide The figure below demonstrates removing the fan from the standard drive bay and placing it onto the hot swap drive bay Pi THR TPID Figure 36 Replacing System Fan from IDE Drive Carrier to the SATA Drive Carrier 58 Revision 1 02 Intel order number C32881 001 Intel amp Entry Server Chassis SC5250 E Appendix A Chassis Spares and Accessories Appendix A Chassis Spares and Accessories Upgrade and Accessory Parts ProdutCode mma UPC aw Bescipion AXX2HSDRVUG 835948 7 35858 146302 1 Hot Swap SCSI Drive Upgrade Kit Upgrade Base Chassi
38. ee ee ee ee ee mmm emere 50 10 3 Product Regulatory Compliance Markings iese ees ee Re ee ee ee ee ee ee ee 51 10 4 Electromagnetic Compatibility Notices AAA 51 1AN USA ME e RA EE OOR OE ET IE 51 10 4 2 FCC Verification Statement ER REEDE Re DEE Ie Gee ER De ee ee N Eg cack 52 04 8 IGES DUS Canada EE Sk Ob o dee oot m aei Eg etis 52 10 4 4 Europe CE Declaration of Conformity see ee ee ee ee ee ee ee ee ee ee RR Re ee ee ee ee 52 10 4 5 Japan EMC Compatibility ee ee 53 10 46 BSMI TaiWa EE 53 11 Environmental Bn E 54 11 1 System Office Environment icon nies sers te dor aa pr eg edi deem deut ie Ge EY Pee d nd dae n 54 11 2 System Environmental Testlfig cte tne ebd an ede opere Rg Ged dele 54 12 Reliability Serviceability and Availability ceu 55 12 1 Reed eiut RE N HON AE AT AL EE RUIN 55 12 2 Sermviceability iios trigo se ee se RO en ak Re N ee es PAS 55 14 Upgradeability sa oe ie RE Ee SA eN AE SR EE RE ek ee Bl ee ee Ke dee ee ke dee 56 13 1 SCSI Hot swap Drive Bay Upgrade rti GE BE GE EE ee ek ees 56 13 2 External SCSI Adapter Cable ie ee AR AR Ee Re RR Ee RE Ee RR ee RE ee ee ee ee ee ee ee ee Re 57 13 3 SATA Hot swap Drive Bay Upgrade sisie see Es ss DEEG ER se et AE ER Rees 58 Appendix A Chassis Spares and Accessories ss EER seen 59 Upgrade and Accessory Pale eoe ci e b aieo Seda nas Macs atu oleae tierna 59 Replacement and Spare Parts for SC5250 E
39. eferred to in this section are defined in the respective server board Technical Product Specification TPS 8 2 Chassis Internal Cables The following cables are provided as part of the chassis kit 8 2 1 Front Panel cable A 34 conductor ribbon cable with 34 pin IDC connectors links the front panel and SSI EEB Revision 3 0 compliant server board 8 2 2 USB cable A 4 conductor USB cable with 10 pin connector for the server board and 4 pin external USB connector is used for connecting the front mounted USB connector to the server board 8 2 3 Fan Connectors The installed system fans provide 3 pin connectors designed to mate with SSI ATX compatible fan headers 8 3 Server Board Internal Cables Depending on the specific server board support of these features some or all of the following cables may not be included as part of the boxed board kit e IDE Cable One or two 40 pin 80 conductor DMA33 66 100 IDE cable e SCSI Cable One 68 pin 68 conductor twisted pair wide SCSI cable with terminator Cable supports connection of up to four SCSI drives to the server board e Floppy Cable One 34 conductor cable featuring two 34 pin IDC connectors 2x17 floppy cable e Serial Cable One 8 conductor cable terminated in a 2x5 header at one end and a 9 pin panel mount Dsub connector on the other Revision 1 02 39 Intel order number C32881 001 System Interconnection Intel Entry Server Chassis SC5250 E 8 4 Accessory Cables 8
40. erence that may cause undesired operation For questions related to the EMC performance of this product contact Intel Corporation 5200 N E Elam Young Parkway Hillsboro OR 97124 1 800 628 8686 This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and the receiver e Connect the equipment to an outlet on a circuit other than the one to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Revision 1 02 51 Intel order number C32881 001 Product Regulatory Compliance Intel Entry Server Chassis SC5250 E Any changes or modifications not expressly approved by the grantee of this
41. erver baseboard has a BMC based management System e Monitors the speed of the fans if present and reports a warning or critical error if outside programmed limits if the server baseboard has a BMC based management system 28 Revision 1 02 Intel order number C32881 001 Intel amp Entry Server Chassis SC5250 E System Peripheral Bays The server chassis SC5250 E hot swap SCSI backplane board set is made up of the following functional blocks e SCSI Bus with SCA drive connectors and active LVDS terminators e Microcontroller with program flash and RAM e SCSI interface that allows the microcontroller to respond as a SCSI target e FC interface to server board e SCSI drive power control e Fault indicator support availability dependent on server baseboard management sub system e Support for two cooling fans fan tachometer inputs and power control e Temperature sensor availability dependent on server baseboard management sub system The hot swap SCSI backplane board set resides in the hot swap drive bay enclosure that is available as an upgrade to the server chassis SC5250 E 5 10 3 SAF TE Board Layout Figure 28 Server Chassis SC5250 E SAF TE Board Revision 1 02 29 Intel order number C32881 001 System Peripheral Bays Intel Entry Server Chassis SC5250 E 5 11 SAF TE Specifications The server chassis SC5250 E hot swap SCSI backplane board set performs the tasks associated with hot swappable SCSI drives enclosur
42. gure View from View from left corner 8 9 right corner TP00493 Figure 17 CPU Air Duct Folding Attach Air Duct to Rear System Fan Locate the air direction arrow on the side of the Rear System Fan and position fan as shown in the following figure The label on the Rear System Fan should face towards the back of the system chassis and the finger guard should face towards the server board Ensure that the Fan Power Cable letter B in the figure exits at lower right hand corner Revision 1 02 17 Intel order number C32881 001 System Cooling Intel amp Entry Server Chassis SC5250 E TP00494 Figure 18 Attach CPU Air Duct to Rear system Fan 1 Place Finger Guard letter C in the figure against matching holes in Rear System Fan 2 Place folded Air Duct letter D in figure against matching holes in Finger Guard and Rear System Fan 3 Fasten Rear System Fan Finger Guard and Air Duct together by inserting a nylon rivet at each of the four mounting holes Use the new nylon rivets that came with your Intel amp Workstation Acoustic Kit Do not re use the old nylon rivets Note that the nylon rivets insert from the inside of the fan see letter E in figure 18 Revision 1 02 Intel order number C32881 001 Intel amp Entry Server Chassis SC5250 E System Cooling TP00501 Figure 19 Install Rear system Fan assembly to System Chassis Revision 1 02 19 Intel order number C32881
43. ial port header One parallel port Two IDE interfaces with UDMA 33 ATA 66 100 support Support for up to four system fans and one processor fan Server System Infrastructure SSI compliant connectors for SSI interface support front panel power connector Revision 1 02 47 Intel order number C32881 001 Compatible Intel amp Server Boards Intel Entry Server Chassis SC5250 E e Hardware Monitor Subsystem Voltage sense to detect out of range power supply voltages Thermal sense to detect out of range thermal values Four fan sense inputs used to monitor fan activity See the Intel Server Board S875WP1 E TPS on the support intel com website for more detail 9 7 Intel Entry Server Board SE7210TP1 E Feature Set The Intel Server Board SE7210TP1 E provides the following feature set o Support for an Intel Celeron processor or an Intel Pentium 4 processor with hyper threading technology in a uPGA478 socket 400 533 800 MHz Front Side Bus FSB Intel E7210 chipset e Intel 827210 Memory Controller Hub MCH e Intel 6300ESB VO Controller Hub ICH5 R e Intel 82802AC 8 Megabit Firmware Hub FWH o Support for single sided or double sided dual inline memory module DIMM double data rate DDR memory providing up to 4 GB of system memory with four 184 pin DIMM sockets e PC3200 400 MHz to run 400 MHz memory at full speed requires an Intel Pentium 4 processor with 800 MHz system bus frequency e PC2700 333 MHz to run 3
44. ils on these waveforms can be obtained in ANSI IEEE STD C62 45 1992 Revision 1 02 9 Intel order number C32881 001 System Cooling Intel amp Entry Server Chassis SC5250 E 4 System Cooling 4 4 Fan Configuration The cooling sub system in the Intel Server Chassis SC5250 E consists of two system fans and one power supply fan A 92mm x 25mm fan located in the front of the fixed hard drive cage draws fresh air into the chassis from the front and provides cooling for the hard drive bay A 120mm x 38mm fan provides cooling at the rear of the chassis exhausting warm air out of the system The power supply fan assists in drawing air through the peripheral bay area through the power supply and exhausting it out the rear of the chassis In addition to these pre installed fans locations for three additional fans are provided for customized configurations Intel does not provide order part numbers for these customizable fan options A 120mm fan can be mounted to the rear of the PCI card guide and provide additional cooling to the PCI card area and two 80mm fans can be mounted at the front of the chassis to the right of the hard drive bay opening to provide more cooling 4 2 Fan Control The fans provided in the server chassis SC5250 E contain a tachometer signal that can be adjusted by the Server Management subsystem for the Intel Server Board SE7501BR2 See the specific baseboard Technical Product Specification for details on how this feature works
45. its the system power to be activated from a variety of sources allowing the implementation of Wake on LAN WOL or other remote management features The 450 Watt entry power supply EPS features and entry SSI Rev 3 0 compliant server board connectors It is positioned as the entry power supply solution for the Intel server boards SE7505VB2 SE7501BR2 SE7500CW2 SE7501CW2 S845WD1 E and S875WP1 E Refer to the 450 W EPS 1 0 Power Supply Specification for details Table 2 System Power Summary SC5250 E 450 Watt EPS Intel Part Number A85459 005 3 3 VDC Output 24 Amp Max 5 VDC Output 20 Amp Max 12 VDC Output 30 Amp Sustained 36 Amp 12 second peak current AC Line Voltage Auto ranging for either 100 127 VAC or 200 240 VAC AC Line Frequency 50 60 Hz System AC Rating 2 5 Amp at 220 VAC Intended server board Intel amp Server Board SE7505VB2 Intel amp Server Board SE7501BR2 Intel amp Server Board SE7500CW2 Intel amp Server Board SE7501CW2 Intel Server Board S845WD1 E Intel Server Board S875WP1 E Intel Server Board SE7210TP1 E Revision 1 02 7 Intel order number C32881 001 Chassis Power Subsystem Intel Entry Server Chassis SC5250 E 3 1 450 Watt EPS 2 0 Power Supply 3 1 1 450 W Power Supply Mechanical Outline The mechanical outline and dimensions for the 450 W supply are an extended PS 2 form factor The approximate dimensions are 86 mm 3 3 inches high by 150 mm 5 90 inches wide by EIE NNS
46. l input output I O connectors are accessible on the rear of the chassis The SSI E bay 3 0 compliant chassis provides an ATX 2 03 compatible cutout for VO shield installation Boxed Intel server boards provide the required VO shield for installation in the cutout The I O cutout dimensions are shown in Figure 1 below for reference R 0 039 MAX TYP 0 100 Min keepout around opening 1 750 0 008 VO Aperture Baseboard Datum 0 0 4 0 150 6 250 0 008 5 196 0 010 0 650 Figure 1 ATX 2 03 I O Aperture Revision 1 02 3 Intel order number C32881 001 Chassis Intel Entry Server Chassis SC5250 E 2 5 Chassis Views F TP00053B A Front panel controls and indicators See Section 7 7 Figure 22 for details Two 5 25 inch removable media drive bays 3 5 inch removable media drive bay Internal hard drive bay cage behind door Security lock USB port mmo ot Figure 2 Front Closed View of Server Chassis SC5250 E Revision 1 02 Intel order number C32881 001 Chassis Intel amp Entry Server Chassis SC5250 E TP00054B Ds E 290000000000000 e Es duo ff CCCOCOCOCOOCOCOOQONOSCOU 7 D 4 CICIGCIGISIEJSICICIOCICIOCU d Saa js OES e N AJOGOOGOOgOOOgOoguts D SI CHHATH sesse ss 9399999999999395 E 2
47. lures MTBF at maximum configuration has been calculated at 74000 hours for KDK at 35 C Table 12 MTBF Calculations Subassembly Standard Standard Configuration with Optional Server at 35 degrees C ambient air Configuration Backplane MTBF hours MTBF hours 450W Power Supply 100 000 100 000 Cooling fans 2 non redundant 300 000 300 000 H Q 12 2 Serviceability The system is designed to be serviced only by qualified technical personnel The desired Mean Time To Repair MTTR of the system is 30 minutes including diagnosis of the system problem To meet this goal the system enclosure and hardware have been designed to minimize the MTTR The following are the maximum times that a trained field service technician should take to perform the listed system maintenance procedures after diagnosis of the system Table 13 Maximum Maintenance Procedure Times Revision 1 02 55 Intel order number C32881 001 Upgradeability Intel amp Entry Server Chassis SC5250 E 13 Upgradeability Listed below are accessory kits available for the server chassis SC5250 E Illustrations are provided to indicate some of the kit contents Not all parts for each kit are shown and the actual part may differ in appearance 13 1 SCSI Hot swap Drive Bay Upgrade Product Code AXX2HSDRVUG The kit includes a SCSI hot swap drive bay with mounting hardware 68 pin LVD SCSI cable for data transfer and 4 pin IC cable for baseboard communication Th
48. n 1 0 does not support fault detection However when the Intel RAID Controller SRCS14L with 2x5 LED cable is installed fault detection is supported Turning off the green LED does this when a fault occurs Note that this is different from previous generations where an amber LED would signify a fault condition If a different type of SATA controller is used fault light control is not supported The RAID Controller SRCS14L provides a 2x5 LED header which is connected between the backplane and drive fault lights Currently no other SATA controllers on the market provide this 2x5 LED header Drive Presence Detection Detects drive presence and makes this information available by turning on the green LED Note that this is also different from previous generation backplanes This functionality works regardless of which SATA controller is being used Drive Power Control Unlike previous generation backplanes power is always applied to slots hot swap functionality is provided via a mating drive connector This is accomplished by using different length pins on both the drive side and the backplane A resistor on the pre charge pins for both the 12V and 5V rails limits the in rush current Hot Swappable Controller HSC Hardware Configurations There are two possible configurations Primary and Secondary available for the SATA backplane on the Server Chassis SC5200 There is no differentiation between backplanes however and from a
49. n additional internal header providing two optional USB ports for front panel support One serial port and one serial port header One parallel port Two IDE interfaces with UDMA 33 ATA 66 100 support Support for up to three system fans and one processor fan Server System Infrastructure SSI compliant connectors for SSI interface support front panel power connector Hardware Monitor Subsystem Voltage sense to detect out of range power supply voltages Thermal sense to detect out of range thermal values Four fan sense inputs used to monitor fan activity See the Intel Server Board S845WD1 E TPS on the support intel com website for more detail 46 Revision 1 02 Intel order number C32881 001 Intel amp Entry Server Chassis SC5250 E Compatible Intel amp Server Boards 9 6 Intel Entry Server Board S875WP1 E Feature Set The server board S875WP1 E server board provides an embedded ATA 100 Valu Raid interface and supports the following feature set Support for an Intel Pentium 4 processor with hyper threading technology in a uPGA478 socket with 512KB L2 cache Does not support Pentium 4 processors with 400KB L2 cache 400 533 800 MHz System Bus Intel 875P chipset Intel 82875P Memory Controller Hub MCH Intel 82801EB VO Controller Hub ICH5 R Intel 82802AC 8 Megabit Firmware Hub FWH Support for single sided or double sided DIMMs DDR 266 DDR 333 and DDR 400 providing up to 4 GB system
50. n1 0 1 The SCSI backplane board set used for the server chassis SC5250 E chassis is the same as that which is used used in the server chassis SC5100 SC5200 chassis 24 Revision 1 02 Intel order number C32881 001 Intel amp Entry Server Chassis SC5250 E System Peripheral Bays 5 8 Hard Drive Activity LED Each SCSI drive turns on a green LED when it is accessed The LEDs are 4 terminal dual color yellow and green physically located on the backplane Table 4 Hard Drive Activity LED HSBP LED Activated LED Designator LED Color DS5C1 Green DS5D1 Green 5 9 Hard Drive Fault LED The hot swap controller HSC is responsible for turning the drive fault LEDs on or off according to the states specified via commands received from SAF TE and the IMB The drive fault LEDs are yellow and indicate failure status for each drive The LEDs are physically located on the LVD SE SCSI backplane The LEDs are 4 terminal dual color yellow and green physically located on the backplane Table 5 Hard Drive Fault LED HSBP LED Activated LED Designator LED Color Revision 1 02 25 Intel order number C32881 001 System Peripheral Bays Intel Entry Server Chassis SC5250 E F TPO Figure 25 Hot swap Drive Bay Rear Isometric View 26 Revision 1 02 Intel order number C32881 001 Intel amp Entry Server Chassis SC5250 E System Peripheral Bays Figure 26 Drive Carrier with Air
51. ntel order number C32881 001 Appendix A Chassis Spares and Accessories Intel amp Entry Server Chassis SC5250 E AXX2HSDRVUG 835948 7 35858 14630 2 1 Hot swap SCSI Drive Upgrade Kit Upgrade Base KDK SKU to five hot swap SCSI Drives FHD3PS450 844924 7 35858 15351 5 Non Redundant 450W Power Supply for SC5250 E Base Chassis 85327 007358 581 16062 9 Spare serial ATA Backplane Board 8 60 Revision 1 02 Intel order number C32881 001 Intel amp Entry Server Chassis SC5250 E Glossary Glossary This appendix contains important terms used in the preceding chapters For ease of use numeric entries are listed first e g 82460GX with alpha entries following e g AGP 4x Acronyms are then entered in their respective place with non acronyms following Term Alternating Current AC ACPI Advanced Configuration and Power Interface ATX Advanced technology extended motherboard type BKM Best Known Method a document created by an Intel organization that details the proper or customary steps used to perform a specific task e g operating system installation Baseboard Management Controller Provides monitoring alerting and logging of critical system information obtained from embedded sensors on the baseboard DC Direct Current Double Data Rate Og O S E R W D EC EE EM EM EP EP E F F F HC HS Hz Hertz 1 cycle second Inter integrated circuit bus ICMB Intelligent Ch
52. ocessor cool kit APTWKTCOOLKIT is available for the Intel Server Chassis SC5250 E and SE7505VB2 only It should be mounted in place of the boxed board processor active heatsinks and fan solutions The APTWKTCOOLKIT requires BIOS 1 08 or newer releases for SE7505VB2 Refer to the Intel Server Chassis SC5200 SC5250 E Hot swap SCSI Bay Upgrade Kit for complete installation instructions This specification details the key features of the product Reference documents listed at the back of this document provide additional product specification details for the server boards backplanes and power supplies validated for use with this chassis Check the compatibility section on the support website for more details http support intel com support motherboards server chassis SC5250 E Revision 1 02 1 Intel order number C32881 001 Chassis Intel Entry Server Chassis SC5250 E 2 Chassis Table 1 Chassis Dimensions approximate Configuration Pedestal Height 17 8 inches 452mm 17 6 inches 447mm if feet are removed Width 9 256 inches 235mm Depth 26 inches 66 04mm Clearance Front 17 83 inches 452mm pue 19 1 inches with bezel 485mm 2 1 System Color The Intel Server Chassis SC5250 E is offered in two color options e Dusty beige GE BR7026 Order code KPTBASE450 e Black GE701 Order code KPTBASE4SOBLK 2 2 Front Bezel Features The standard front bezel is molded plastic and attaches to the front of the chassis wi
53. r VO panel conforms to Advanced Technology Extended ATX Specification Revision 2 03 The chassis supports seven full length expansion cards The chassis is provided with a front panel board designed for Server Standards Infrastructure SSI Entry E Bay EEB 3 0 compliant server boards An optional hot swap drive bay kit product code AXX2HSDRVUG provides an upgrade path to allow the server chassis SC5250 E to support five hot swap drives This optional hot swap SCSI hard disk drive bay supports up to five 1 inch single connector attachment SCA low voltage differential SCSI LVD hard drives to enhance serviceability availability and upgradeability of the system When the hot swap drive bay is installed it replaces the fixed hard drive bay An optional hot swap upgrade drive bay assembly ASATAHSDB is available for the Server Chassis SC5200 and Server Chassis SC5250 E It should be mounted in place of the middle three 5 25 inch drive trays of the base non redundant chassis models For the redundant power models the upgrade accessory should be installed in the lower three 5 25 inch drive trays to bring the total number of available hot swap SATA drives to eight Refer to the nte Server Chassis SC5200 SC5250 E Hot swap Bay Upgrade Kit for complete installation instructions Note Part of the replacement process requires removing the fan from the fixed hard drive bay attaching it to the rear of the hot swap drive bay An optional passive pr
54. re 34 Figure 35 Figure 36 viii Hot swap Drive Bay Rear Isometric View 34 Drive Carrier with Air Baffle Installed ee ee AR ER ER RE ee ee RE ee ee RR ee ee ee ee 35 Intel Server Chassis SC5200 and SC5250 E SATA Backplane 36 Front Panel Controls and Indicators eese 38 Replacing System Fan from IDE Drive Carrier to the SCSI Drive Carrier 56 External SCSI Adapter Cable Deia 57 Replacing System Fan from IDE Drive Carrier to the SATA Drive Carrier 58 Revision 1 02 Intel order number C32881 001 Intel amp Entry Server Chassis SC5250 E List of Tables List of Tables Table 1 Chassis Dimensions approximate see Ee EE KA Re Eed Ge eene nennt enne ined 2 Table 2 System Power SUMMAaFY re vee repente ke ttr ete pi o exp Se Eh LS RYE ENEE EUH FR E RR en 7 Table RR Ee ale E CEET 24 Table 4 Hard Drive Activity LED es ese e er ata credet Ge ee eebe 25 Table 5 Hard Drive Fault LEID 25 Table 6 SATA Bus ID Assignments EE eiie Pe ER Ee Ge EE Re DE EE 32 Table 7 Hard Drive Activity LED with Intel RAID Controller SRCS14L Installed 33 Table 8 Hard Drive Fault LED with Intel RAID Controller SRCS14L Installed 33 Table 9 Connector Reierences eea ae i eene nnnm nnne nenne nnne nnne 36 Table 10 Front Panel LED Funchons Ee RR AAR ee Rede ee ee Re ee RR Ee RR ee ee 38 Table 11 System Office Environment Summary sess
55. s must be verified to ensure compliance to the manufacturer s specifications The 5 25 inch peripherals are removable from the front of the chassis after taking off the access cover and removing the front bezel EMI shield panels are installed and should be retained in unused 5 25 inch bays to ensure proper cooling and EMI conformance Note Caution when approaching the maximum level of integration for the 5 25 inch drive bays Power consumption of the devices integrated needs to be carefully considered to ensure that the power supply maximum power levels are not exceeded Typical configurations can supply enough power for a floppy drive a tape drive a CD ROM and four fixed hard drives 5 3 Hard Drive Bay The server chassis SC5250 E comes with a removable hard drive bay that can accept up to six cabled 3 5 x 1 hard drives Power requirements for each individual hard drive may limit the maximum number of drives that can be integrated to a server chassis SC5250 E This bay has a 92mm 6 2 inches x 25mm fan mounted to the front to provide airflow to the hard drives mounted in it The drive bay secures with two screws in the front of it and two screws on the side Note The hard drive bay must be slid forward or removed to install the baseboard The server chassis SC5250 E server chassis is capable of accepting a single SCSI hot swap backplane hard drive enclosure in place of the fixed drive bay This is the same enclosure that is used in the
56. s to five drives AXXEXTSCSICBL 830656 7 35858 13953 3 1 External SCSI Cable Accessory For use with SCSI Knock out on rear of chassis ASATAHSDB 853276 7 35858 16062 9 1 Hot Swap Upgrade Kit Upgrade Base Chassis for four drives 1 APTWKTCOOLKI 858795 7 35858 16597 6 1 Workstation cooling kit for Intel Server Board T SE7505VB2 only and Intel Server Chassis SC5250 E Improves system cooling and acoustics Includes 2 Heatsinks retention mechanisms fan spacers cooling duct screws and documentation Replacement and Spare Parts for SC5250 E 1 FPTCOSMKIT 852424 735858159739 Cosmetic Kit e One black bezel e One dusty beige bezel e Four chassis feet e Two side cover latches FPTPMKIT 852425 735858159722 1 Preventive Maintenance Kit One Front Panel Board One Front Panel cable One USB cable One Intrusion Switch cable One 92MM fan One 120MM fan with fan guard attached One box of hardware which consist of Two left side peripheral rails Two right side peripheral rails One lock plate Fifteen standoffs for server board mounting Nine screws to mount RM 38 screws to mount server board etc common screw Eleven countersunk screws to mount CDROM floppy drive etc Four screws to mount fan to a HS bay Four tie wraps for cable management One cable clamp for cable management One cable tie to cable management with HS bay One rubber bumper for server board mounting Two mounting brackets for HS bay Revision 1 02 59 I
57. se sesse ee sees ese ede ee RR Ee RR ee RR ee RR Ee RR ee RR ee nnne nnne 8 3 1 1 450 W Power Supply Mechanical Outline iss sse 8 3 1 2 450 W Power Supply Fan Reourements sss 8 3 1 3 AG Power Eine ore D NE nuu dieat 9 System Cooling a cite Aon caer ca EE EA fere Salen au nation Oe p Rin Por Ra ee es aee 10 4 1 Fan GonflguratlOn EE WE eaten 10 4 2 Fan Control sa o eere pe et DE cO ie P p RERO TR EY IR te tes 10 4 3 Cooling SOMO RS DS AE Re ee eie p trie Rd etn eda ened es oe 10 4 4 Intel APTWKTCOOLKIT for SE7505VB2 Intel Server Board Configuration 12 4 5 Remove the Wind Tunnel Assembly iii ie ee Eb EE ER EE Ee EE ee Ge kenne nnn eed 13 4 6 Installing the Intel APTWKTCOOLKIT for SE7505VB2 Intel Server Board 15 4 7 Configuring CPU Duct Fan Assembly the Intel APTWKTCOOLKIT for SE7505VB2 Intel Server er EE 17 4 8 Install the Front Fan Spacers for the Fixed Hard Drive Bay 20 System Peripheral BayS ss RE NE SE ER EE AE ie ge ee De Ai Wes do GEEN EE N ONE EN ed eed ee ae ae ie 22 9 1 4 6 Peripheral Drive Bay EDE setti fedus i DR EE nc EE EE EG Ge ES Eg EES 22 5 2 m29 Perptieral Drive Bays ce RE EER eed DE SEE ESEG Ua utet AR ee MI Re iu e 23 GE Hard Drive Bay audae insisted ates ee ge nivea tha ED ae ag ge hd ate d een Ced 23 5 4 SCSI Multi Mode TerminatiOn user ee Se ERK KA EE Gee Ge Re bee nennen nnne 23 SNAKE MIC TTE 24 26 EETSIOrProGGUGE EE 24 5 7 Device ede
58. t header Two Serial ATA SATA ports provide interface for SATA hard drives and ATAPI devices Two IDE interfaces with Ultra 33 66 and 100 DMA mode Support for up to six system fans and one processor fan Server System Infrastructure SSI compliant connectors for SSI interface support front panel power connector Intel Server Management 5 8 support via the National Semiconductor PC87431 integrated management controller See the Inte Server Board SE7210TP1 E TPS on the support intel com website for more detail Revision 1 02 49 Intel order number C32881 001 Product Regulatory Compliance Intel Entry Server Chassis SC5250 E 10 Product Regulatory Compliance The server chassis SC5250 E chassis is designed and tested to meet the standards and regulation listed below when configured with the Intel server boards specified 10 1 Product Safety Compliance The SC5250 E complies with the following safety requirements e UL 1950 CSA 950 US Canada e EN 60 950 European Uni n e IEC 60 950 International e CE Low Voltage Directive 73 23 EEC European Limits e EMKO TSE 74 SEC 207 94 Nordics 10 2 Product EMC Compliance The system has been tested and verified to comply with the following EMC regulations when configured with the Intel server boards specified For information on compatible server boards refer to Intel s Server Builder website http www intel com go serverbuilder or contact your local Intel represen
59. t swap drive bay is installed a bi color hard drive LED is located on each drive carrier five total to indicate specific drive failure or activity For pedestal systems these LEDs are visible upon opening the front bezel door Revision 1 02 37 Intel order number C32881 001 System Peripheral Bays Intel Entry Server Chassis SC5250 E CEN Power Sleep LED en Power button NMI button Reset Button Sleep Button LAN 1 Activity LED LAN 2 Activity LED Hard Drive Activity LED Status LED rommoouv Figure 33 Front Panel Controls and Indicators Table 10 Front Panel LED Functions Amber EE Sleep S1 Power off or Sleep S4 LAN 1 Link Activity Green oJ Linked LAN activity Disconnected LAN 2 Link Activity Green Linked BLINK LAN activity Disconnected Amber Fault OFF No Activity Status LED Green ON System ready not supported by all server boards BLINK Processor or memory disabled Amber ON Critical temperature or voltage fault CPU Terminator missing IK Power fault Fan fault Non critical temperature or voltage fault ar Fatal error during POST For additional details about front panel functions supported for a specific board refer to the individual server board specifications 38 Revision 1 02 Intel order number C32881 001 Intel amp Entry Server Chassis SC5250 E System Interconnection 8 System Interconnection 8 1 Signal Definitions The pin out on the connectors r
60. tative e FCC Class A Verification Radiated and Conducted Emissions USA e ICES 003 Class A Radiated and Conducted Emissions Canada e CISPR 22 3 Edition Class A Radiated and Conducted Emissions International e EN45022 Class A Radiated and Conducted Emissions European Union e EN45024 Immunity European Union e EN6100 3 2 amp 3 Power Harmonics amp Fluctuation and Flicker e CE EMC Directive 89 33 EEC European Union e VCCI Class A Radiated and Conducted Emissions Japan e RRL Class A Radiated and Conducted Emissions Korea e BSMI Class A Radiated and Conducted Emissions Taiwan 50 Revision 1 02 Intel order number C32881 001 Intel amp Entry Server Chassis SC5250 E Product Regulatory Compliance 10 3 Product Regulatory Compliance Markings This product is provided with the following Product Certification Markings e UL cUL Listing Mark e CE Mark e German GS Mark e Russian GOST Mark e FCC Class A Verification Marking e ICES 003 Canada EMC Compliance Marking e VCCI Class A Mark e Australian C Tick Mark e Taiwan BSMI Certification Number and Class A Warning 10 4 Electromagnetic Compatibility Notices 10 4 1 USA This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interf
61. th a hinge on the right side and two snaps on the left The snaps at the left attach behind the access cover preventing accidental removal of the bezel The bezel can only be removed by first removing the server access cover This provides additional security to the hard drive and peripheral bay area The bezel includes a key locking door that covers the drive cage area The peripheral bays are covered with plastic snap in cosmetic pieces that must be removed to add peripherals to the system Front panel buttons and lights are located along right side the peripheral bays 2 3 Security A variety of chassis security options are provided at the system level as listed below e Aremovable padlock loop at the rear of the system access cover can be used to prevent access to the microprocessors memory and add in cards A variety of lock sizes can be accommodated by the 0 270 inch diameter loop e Atwo position key lock switch will unlock the front bezel e Achassis intrusion switch is provided allowing server management software to detect unauthorized access to the system cover 2 Revision 1 02 Intel order number C32881 001 Intel amp Entry Server Chassis SC5250 E Chassis Note See the technical product specification appropriate to the server board for a description of BIOS and management security features for each specific supported platform The technical product specifications can be found at http support intel com 2 4 VO Panel Al
62. tivity and fault LEDs via a 2x5 LED header Table 6 SATA Bus ID Assignments 32 Revision 1 02 Intel order number C32881 001 Intel amp Entry Server Chassis SC5250 E System Peripheral Bays SATA Drive Intel amp RAID Controller SRCS14L Channel 7 4 Hard Drive Activity LED When a drive is first plugged in the green LED turns on and stays on signifying that the drive has been detected The green LED will then blink if there is activity to the drive and a RAID Controller SRCS14L with 2x5 LED header has been installed The LEDs are 4 terminal dual color yellow and green LEDS that are physically located on the backplane Table 7 Hard Drive Activity LED with Intel amp RAID Controller SRCS14L Installed Hot swap Backplane LED Activated LED Designator LED Color 7 5 Hard Drive Fault LED Hard drive fault indication is not currently supported as per the SATA 1 0 Specification However if a fault occurs on a drive and the backplane is connected to a RAID Controller SRCS14L with the 2x5 LED header installed the green LED will turn off when a fault occurs Table 8 Hard Drive Fault LED with Intel amp RAID Controller SRCS14L Installed Hot swap Backplane LED Activated LED Designator LED Color Revision 1 02 33 Intel order number C32881 001 System Peripheral Bays Intel Entry Server Chassis SC5250 E MEN N EI Figure 30 Hot swap Drive Bay Rear Isometric View
63. try Server Chassis SC5250 E System Peripheral Bays This connector is shared for both Drive 2 Host Side Drive 3 and Drive 3 Drive 3 is the one closest to the PCB This connector is only used with the Intel amp Raid Controller LED Connector SRCS14L and is used to drive the activity LED s 7 6 2 SATA Hot swap Backplane Specifications The Server Chassis SC5200 and SC5250 E hot swap SATA backplane is an embedded application subsystem which during normal operation does the following e Responds to SATA messages transmitted to the backplane via the SATA bus The Server Chassis SC5200 and SC5250 E hot swap SATA backplane board set is made up of the following functional blocks e SATA interface with SATA drive connectors e SATA drive power control e Fault indicator support only supported when a RAID Controller SRCS14L is installed 7 1 Front Panel The front panel control buttons and LED indicators are displayed in Error Reference source not found Not shown in the figure below is a tool activated non maskable Interrupt NMI switch located below the Status LED Server chassis SC5250 E provides a 34 pin cable option with the chassis kit A 34 pin Entry Ebay SSI rev 3 0 front panel header for Intel boards is located on the back of the front panel This allows for a 34 pin ribbon cable connection for use with SSI rev 3 0 compliant server boards The connector cable is compatible with the 24 pin SSI standard When the ho
64. user s perspective all drives are treated in the same manner as if they were connected directly to the controller thereby making the backplane appear transparent Revision 1 02 31 Intel order number C32881 001 System Peripheral Bays Intel Entry Server Chassis SC5250 E 7 System Peripheral Bays 7 1 3 5 inch Hot swap Hard Drive Bays The SATA backplane provides support for SATA devices using Low Voltage Differential Signaling The backplane has a connector to accommodate a SAF TE controller on an add in card The backplane supports four 1 inch hot swap SATA drives when mounted in the docking drive carrier When a RAID Controller SRCS14L is installed two SATA backplanes may be connected for a total of eight SATA drives valid only in 650 W redundant chassis The Server Chassis SC5250 E supports only one SATA hot swap drive bay supporting four 3 5 inch wide SATA hard drives Drives are accessible by opening the front access door Four metal carriers are provided with each hot swap bay to mount the hard drives Each carrier features a plastic handle and bezel with an activity fault indicator When no drive is installed in a carrier the air baffle should remain in place to ensure proper cooling of the hard drives The Intel Server Chassis SC5250 E hot swap drive bay is designed to accept four one inch peripherals that consume a maximum of 18 W of power each This wattage number is intended as a guideline Thermal performance of specific h
65. vides new fan control changes to improve acoustics In addition Intel offers a new upgrade kit for maximum improvement on workstations environments with C15472 701 level boards BIOS releases contain critical errata fixes Therefore Intel recommends updating the BIOS on this board to the most current release BIOS releases available for the server board SE7505VB2 are available at http support intel com support motherboards server se7505vb2 See the release notes available with the BIOS release for installation instructions and corrections available in the release 4 5 Remove the Wind Tunnel Assembly The Intel amp Workstation Acoustic Kit can be used to retrofit either a new or existing Intel amp Server Board SE7505VB2 system in the Intel Server Chassis SC5250 E It replaces the active heatsink solution presented on Section 4 2 Please refer to Intel amp WorkStation Cooling Kit User s Guide for complete instructions for removal of Active heatsink Solution Order Number C55113 001 Rev 2 TP00495 Figure 10 Remove wind Tunnel for your Intel amp Server Board SE7505VB2 Revision 1 02 13 Intel order number C32881 001 System Cooling Intel amp Entry Server Chassis SC5250 E TP00502 Figure 11 Remove the Retention Mechanism if present on your Intel amp Server Board SE7505VB2 TP00496 Figure 12 Remove Retention Mechanism when present on your Intel Server Board SE7505VB2 TP00497 Figure 13 Remove

Intel SC5250-E computer case

Contents

Download Pdf Manuals

Related Search

Related Contents