KRAM 84100 car kit
Contents
1. 1 If there is supply on the red constant 12v wire but not on the blue ignition wire the car may require an alternative ignition source See installation step 4 2 Check that the bullets on the supply wires are properly connected The supply wires are the red blue and black wires 3 Check for a blown fuse on the Audio2Car harness or in the cars fuse box The carkit does not turn off when the key is removed from the ignition barrel Your carkit needs a real ignition source Please check the following 1 Is there an ignition supply on the blue wire There should be no voltage on the blue wire when there is no key in the ignition See installation step 4 Not all speakers are muted Try to disconnect the Mute box Relays and the Carkit adaptor C or additional Drive and Talk mute box from the Audio2Car harness then turn on the radio and check the following 1 All front door speakers keep playing This is the wrong Audio2Car harness for this car sound system 2 A few speakers keep playing This is the wrong Audio2Car harness for this car sound system 3 All speakers are now muted e Carkits with 1 speaker mute Some carkits can only mute 1 speaker channel with their build in mute box This is normally stated on the label on the carkit adaptor for these carkits else please check the carkit manual If a full mute is desired with these carkits then this can be achieved by either connecting the mute wire or adding an additional mute box f2. Audio ZCar Audio ZCar The professional mute The professional mute Audio2Car harness Product Description The Audio2Car range allows OEM car speakers to be used for aftermarket Audio equipment Audio2Car allow the car speakers to be used for audio playback from aftermarket Audio equipment For a com plete installation two or more item numbers are required See description at the last page For a complete installation normally a minimum of two item numbers are re quired Audio equipment with build in mute function If the Audio equipment is equipped with a build in mute function two item numbers are required The 1st item number is the Audio2Car harness The 2nd item is a Audio2Car carkit adaptor Audio equipment without build in mute function If the Audio equipment is not equipped with speaker relays a Mute box from Kram Drive amp Talk range can be added together with a Drive amp Talk carkit adaptor Speaker function This is achieved by connecting Audio equipment with build in speaker relay function or by using a Mute box from the Kram range This way the radio sound is muted and the sound from the aftermarket Audio equipment is sent through the car speakers You will achieve a perfect sound without interference from the car radio Mute wire function The mute wire is connected from the 24 pin connector to the most used mute position for the car model This enables the use of the radios built in mute function If the radio does n
3. E87 E88 amp 3 series E90 E91 E92 E93 The amplifier is located in the left side of the boot rear of the wheel arc and below CD changer and floor An Audio2Car extension cable item no AE5 is also re quired 5 series E63 E64 amp 6 series E60 E61 The amplifier is located in the left side of the boot rear of the wheel arc An Audio2Car extension cable item no AE5 is also required 7 series F01 F02 The amplifier is located in the left Pictures of amplifier in 3 series E90 side of the boot rear of the wheel arc An Audio2Car extension cable item no AE5 is also required X1 series E84 The amplifier is located in the left side of the boot An Audio2Car extension cable item no AE5 is also required X3 series The amplifier is located in the boot behind the left side cover above the rear left wheel arch An Audio2Car extension cable item no AE5 is also required X5 series E70 amp X6 series E71 The amplifier is located in the left side off boot behind the side cover An Audio2Car extension cable item no AE5 is also required Other models The amplifier can normally be found in the left side of the boot An Audio2Car extension cable Audio ZCar The professional mute item no AE5 is also required 3rd Connect the car specific cable Disconnect the connector on the amplifier unit and insert the Audio2Car harness between the connector and amplifier unit Warning Be careful not to kink or break any of the orang
4. e optical wires located in separate connector They are fragile Ath Check ignition source When the cable set is delivered the blue ignition wire is connected to the red constant 12V wire with a bullet connector If a real ignition source is needed for the chosen carkit an IGNIBOX item no I can be inserted to create an artificial ignition source or the blue ignition wire can be disconnected from the red constant 12v and manually connected to an ignition source found elsewhere 5th Check fuse size The fuse on the Audio2Car cable should not be bigger than the ones used on the wiring loom supplied with the carkit The fuses on the Audio2Car cable should be replaced with a size similar to the ones supplied with the carkit Note Never exceed the Maximum Fuse size for the Audio2Car cable See first page 6th Extend the cable set to the preferred location of the carkit Use the extension cable B or additional Drive amp Talk Mute box with extension cable to extend the cable set to the preferred location of the carkit Behind the glove box is recommended 7th Connect the carkit adaptor Connect the carkit adaptor to the extension cable Connect the carkit adaptor to the carkit Troubleshooting Guide Carkit does not start up Check if there is 12V between the black and the red wire and also between the black and blue wire in the 24 pin connector when the car is started If there is not 12v on both wires please check the follow ing
5. nstallation description for 84100 Audio2Car harness used for BMW with Hifi Professional sound system Bullet Connectors gt A Audio2Car Harness Needed items Item number 84xxx A Audio2Car harness including Mute box Relays amp Mute loop B Audio2Car extension cable bought separately C Audio2Car carkit adaptor bought separately D Carkit bought separately 24 pin Connectors B Audio2Car Extension cable Item number AEx Note B amp C can be replaced by an additional Mute box and extension cable from our Drive amp Talk range 24 pin Connectors gt C Audio2Car Adaptor Identification of sound system Item number AAxxx This cable will only fit cars equipped with the Hifi Professional sound system If you do not have an amplifier in the specified location or the amplifier connector is a 42 pin type you properly have the smaller Hifi speaker system instead Please see our complete cable list for further information about choosing the right cable for your sound system The list can be downloaded at www kram dk Installation When delivered this Audio2Car cable set is always fitted with a Mute box and a Mute loop connected 1st Remove the key from the ignition barrel This is done to avoid error messages on the cars electrical system Such error can only be reset by an authorised BMW Repair shop 2nd Locate amp uncover the amplifier unit Amplifier locations 1 series
6. ot have such function or the mute exists in a different connector than the ones used on the Audio2Car harness the mute wire can be found in a yellow fly wire fitted with a bullet connector Audio2Car Carkit Adaptors Power supply All Audio2Car cables have an integrated power supply for the Audio equipment in the 24 pin vs connector The constant 12v and the ground supply are normally sourced from the radio supply This way power supply of most Audio Equipment can be achieved without cutting the cars wiring loom The constant 12V wires Several different carkit adaptors j are red and the ground wires are black are available for Carkits that have a build in mute function for 1 or 4 Speakers Please see the complete range of Audio2Car carkit adaptors at our website www kram dk Ignition supply If an ignition source is available in the radio connector then it will normally also be available in the 24 pin connector If an ignition source is not available a constant 12V source is connected to the Ignition pin via bullet connectors If a real ignition is required for the chosen Audio Equipment an IGNIBOX item no I can be connected to create an artificial ignition Or an ignition source found elsewhere can be connected to the bullet with the blue wire The 12V ignition wires in the Audio2Car cable are blue Aux integration The 4 pin connector on the Audio2Car harness allow a Kram Aux solution to be connected This will allow the Exam
7. ples of ee use of the car sound system amplifier for Music playback and thereby achieving higher sound quality carkit adaptors Technical Specifications Description L shaped with bullet connections for Ground Constant 12v and Ignition Drive amp talk Mute box Normal Wire dimensions AWG 18 for power wires AWG 20 for all other wires range Standard Fuse sizes 2 Amp for constant supply 1 Amp for Ignition supply Maximum Fuse size 7 5 Amp for constant supply 7 5 Amp for Ignition supply Maximum output pr speaker 100 Watt RMS 200 Watt music power 4 Ohm Size 400 x 400 mm i vee Configuration chart for 24 pin connector Several different types of mute boxes are on ae ee ea res ea oe a a lt i ue Const IGN OutL OutR RR RF LF LR LR LF RF RR is a os aad ae a la a Pi turn your Audio2Car cable into a Kram saa z i j i 2 u t t t d a 7 hin a 7 A ee i oe ey 2 lt Drive amp Talk solution Therefore you will Mute Line Line Radio Radio Radio Radio Spk Spk Spk Spk ee also need a Drive amp Talk carkit adaptor Out L Out R RR RF LF PLR LR LF RF RR Adding this adaptor turns your Audio2Car cable does P Please see the Complete Drive amp Talk your Audio2Car cable into a not include an ignition source range at our website Connector seen from cable entry side Kram ISO2CAR solution This adaptor is plug and play vwa kimik with your Audio2Car cable EN098 V01 Audio ZCar The professional mute I
8. rom our Drive amp Talk range e Carkits with 4 speaker channel mute or when additional Drive amp Talk mute box is used Please check that the Mute Loop is attached to Mute box delivered with the cable set Else please try another carkit Carkit sound is in the wrong speakers or there is no carkit sound 1 The two 24 pin connectors in the cable set may be switched The carkit should be connected to the 24 pin connector with the Green White Gray and Purple wires 2 The carkit may be defective Please try another carkit Radio will not turn on or not working properly after installation 1 Please check for a blown fuse at the radio or in the car fuse box 2 Remove the Audio2Car harness and connect the radio to the original car connector If the radio is now work ing replace the Audio2car harness See our complete Radio Mute program on our website www kram dk
Download Pdf Manuals
Related Search