Omnitron 6500-FK network switch
Contents
1. Left Position Right Position 4 Port Switch Module DIP Switch Backplane Port A Enable Disable BP A EN DIP Switch This DIP Switch must be in the LEFT position factory default for the module to operate correctly The switch provides backplane connectivity with the other switch module Backplane Port A Enable Disable BP B EN DIP Switch This DIP Switch must be in the LEFT position factory default for the module to operate correctly The switch provides backplane connectivity with the other switch module UTP Auto Negotiate Manual AN MAN DIP Switch Port 1 or Port 2 When this DIP Switch is in the UTP Auto Negotiate AN position factory default the UTP port automatically determines the speed and duplex mode of the connecting UTP device If the connecting UTP device cannot provide the proper signal to indicate its own mode of operation this DIP Switch should be set to the UTP Manual mode Man position Manual mode requires manually configuring the UTP port to match the speed and the duplex mode of the connecting UTP device using the 10 100 and UTP FDX HDX DIP Switches When a UTP port is configured for Auto Negotiation the automatic crossover detection is enabled for that particular UTP port Automatic crossover detection Page 5 is disabled when the UTP port is configured for manual negotiation UTP 10 100Mbps 10 100 DIP Switch Port 1 or Port 2 When the UTP AN MAN DIP2. or inadeguate use and or maintenance of the eguipment by Buyer Buyer supplied eguipment Buyer supplied interfacing unauthorized modifications or tampering with eguipment including removal of eguipment cover by personnel not specifically authorized and certified by Omnitron or misuse or operating outside the environmental specification of the product including but not limited to voltage ambient temperature radiation unusual dust etc or improper site preparation or maintenance No other warranty is expressed or implied Omnitron specifically disclaims the implied warranties of merchantability and fitness for any particular purpose Exclusive Remedies The remedies provided herein are the Buyer s sole and exclusive remedies Omnitron shall not be liable for any direct indirect special incidental or consequential damages whether based on contract tort or any legal theory TECHNICAL SUPPORT If you encounter problems with this product contact Omnitron Technical Support Phone 800 675 8410 949 250 6510 Fax 949 250 6514 Address Omnitron Systems Technology Inc 140 Technology Dr 500 Irvine CA 92618 Email support omnitron systems com URL http www omnitron systems com Form 040 06500 FK1 A 02 07 Page 9
3. OST Omnitron Systems Technology Inc FlexSwitch 8U Model 6500 FK Replacement Kit User Manual 140 Technology 500 Irvine CA 92618 Phone 949 250 6510 Fax 949 250 6514 Table of Contents 1 0 INTRODUCTION 3 ci ssssstasiain i iansa Si vanne ini 1 1 General Description suosan nn antama maana naan annenn 2 0 NSTALLATI O N oisin oss masa oceanic Sienassa lyn 2 1 Chassis Installation oouonnn nm a aan an annean 2 2 Module Installation oooooaan annon aa naamaan annan 2 4 UTP installation senaian kean a mannaa ahnas man dT a Sak T maa andaa raid 3 0 CONFIGURATION i asisaissasmavsasaasana saamasta kia vantk nat ksen A Tea KmsRASTA 3 1 AC Site Preparation ooonnnuommn anna an maana ennnen 3 2 AC Powered Chassis Mounting ccsseeeeesesereeeseeeeees 3 3 Configuring the DIP SWitches ccseccssseeeeseseeeeeseeeees 3 3 1 Switch Module oss cots cc eeesc ols ada cts tect iansincaa ee eeetes 4 0 EEDINDICATORSssisstnvunata takk aavietyat m T sas eae ee 4 1 Switch Module iiianoe eee eis 5 0 SPECIFICATIONS lt eiin aeiia anaa imel isa aaa aeea naiara aaeain Page 2 1 0 INTRODUCTION 1 1 General Description The 6500 FK is the direct replacement for the discontinued FlexSwitch Model 600XC 8U The 6500 FK replacement kit consists of two iConverter 4Tx Switch Modules installed in a iConverter 2 Module chassis The 6500 FK provides eight auto negotiatin
4. Switch described above is in the manual MAN position the 10 100 DIP Switch determines the speed of operation for the designated UTP port Setting the 10 100 DIP Switch to 100 position factory default forces the UTP port to operate at 100Mbps Setting this DIP Switch to 10 position forces the UTP port to operate at 10Mbps Adjust the 10 100 DIP Switch to match the speed of the connecting UTP device UTP Full Half Duplex HD FD DIP Switch Port 1 or Port 2 When the UTP AN MAN DIP Switch described above is in the manual MAN position the HD FD DIP Switch determines the duplex operation mode for the UTP port Setting the HD FD DIP Switch to UTP Full Duplex FD factory default position forces the UTP port to operate in Full Duplex Setting this DIP Switch to HD forces the UTP port to operate in Half Duplex Adjust the UTP Half Full Duplex DIP Switch to match duplex mode the connecting UTP device When the UTP AN MAN DIP Switch is in the Auto Negotiate AN position and the UTP Full Half Duplex DIP Switch is in the Full Duplex FD position the UTP port Auto Negotiates to Full or Half Duplex When in the Half Duplex HDX position the UTP port functions only in Half Duplex Page 6 4 0 LED INDICATORS 4 1 Switch Module Each 4 Port Switch Module has LED indicators to provide connection information 4 Port Switch Module LED Function Off Stat
5. e ON State Power Pwr Yellow No Power On Module has Power Port 1 100 Link Green Not Linked at 100Mbps On Port Linked at 100Mbps Blinking Data Activity Port 1 10 Link Green Not Linked at 10Mbps On Port Linked at 10Mbps Blinking Data Activity Port 2 100 Link Green Not Linked at 100Mbps On Port Linked at 100Mbps Blinking Data Activity Port 2 10 Link Green Not Linked at 10Mbps On Port Linked at 10Mbps Blinking Data Activity Port 3 100 Link Green Not Linked at 100Mbps On Port Linked at 100Mbps Blinking Data Activity Port 3 10 Link Green Not Linked at 10Mbps On Port Linked at 10Mbps Blinking Data Activity Port 4 100 Link Green Not Linked at 100Mbps On Port Linked at 100Mbps Blinking Data Activity Port 4 10 Link Green Not Linked at 10Mbps On Port Linked at 10Mbps Blinking Data Activity 4 Port Switch Module LED Indicators Page 7 5 0 SPECIFICATIONS Description Protocols UTP Cable Type UTP Connector Type DIP Switches Power Reguirements Dimensions Weight Compliances Temperature Humidity non condensing Altitude operational with 1536 bytes max frame size Category 5 and higher W 6 7 x D 5 51 x H 1 87 3 0 lbs UL CE FCC CLass A NEBS Level 3 Operating 0 to 50 C Storage 40 to 80 C lt 4000m 13 000 ft Warning The operating description in this Instruction Manual is for use by qualified personnel only To avoid elec
6. g 10 100 UTP ports with auto crossover that enables easy attachment to hubs switches and workstations The 6500 FK provides on board DIP Switches for manual configuration of Port 1 and 2 on each 4 Port Switch Module 2 0 INSTALLATION 2 1 Chassis Installation The 6500 FK is designed to accommodate wall mounting and tabletop installations For wall mounting the 8249 0 Wall Mount kit sold separately is designed to attach the chassis to a wall backboard or other flat surfaces For tabletop installations place the unit on a flat level surface Attach the rubber feet to the bottom of the chassis to prevent the unit from sliding Make sure the unit is placed in a safe dry and secure location For external power installation and configuration see section 3 0 2 2 Module Installation The modules are pre installed in the 2 Module chassis with the backplane enabled on both modules If the modules are removed carefully slide the module into the open slot Align the module with the installation guides and ensure that the module is firmly seated against the backplane Secure the module by fastening the front panel thumbscrew push in and turn clockwise to tighten to the chassis front 2 4 UTP Installation Connect the UTP port via a Category 5 cable to a 10Base T or 100Base Tx Ethernet device 3 0 CONFIGURATION 3 1 AC Site Preparation e Power source should be available within 5 ft of the chassis and installed per the National Elec
7. trical Code ANSI NFPA 70 e This equipment requires a 100 240VAC 0 5Amp 50 60Hz power outlet Appropriate overloading protection should be provided on the AC power source outlets utilized e The operating temperature of this equipment is 0 to 50 degrees C If installed in a closed or multi module rack assembly the operating ambient temperature of the rack must not exceed the maximum rated 50 degrees C e Installation of the equipment should be such that the air flow in the front and back of the chassis is not compromised or restricted e Never use this equipment to carry any weight except its own Never use it as a shelf to support the weight of other equipment 3 2 AC Powered Chassis Mounting Attach the AC power cord to the back of the Power Receptacle and plug into the AC outlet Any installed modules will illuminate the power LED Page 4 3 3 Configuring the DIP Switches The 6500 FK has been pre configured with Auto Negotiation enabled for plug and play easy of use However the iConverter Switch Modules offer additional configuration flexibility 3 3 1 Switch Module Each 4 Port Switch Module has been pre configured for Auto Negotiation On board DIP Switches are available to manually configure Port 1 and 2 of each module The figure indicates the factory default settings BPAEN CE BP B EN CE MAN MM AN s 10 muu 100 9 3 HD muu FD MAN MM AN s 10 MM 100 JR HD muu FD
8. trical shock do not perform any servicing of this unit other than that contained in the operating instructions unless you are qualified and certified to do so by Omnitron Systems Technology Inc Caution All user required operations can be performed without opening the unit Never attempt to open or remove the cover or tamper with the unit There are no user replaceable or serviceable parts in this unit Equipment is not intended to be installed and used in a place home school or public area accessible to the general population Warranty This product is warranted to the original purchaser against defects in material and workmanship for a period of TWO YEARS from the date of shipment A LIFETIME warranty may be obtained by the original purchaser by REGISTERING this product with Omnitron within 90 days from the date of shipment TO REGISTER COMPLETE AND MAIL OR FAX THE ENCLOSED REGISTRATION FORM Or you may register your product on Page 8 the Internet at http www omnitron systems com During the warranty period Omnitron will at its option repair or replace a product which is proven to be defective For warranty service the product must be sent to an Omnitron designated facility at Buyer s expense Omnitron will pay the shipping charge to return the product to Buyer s designated US address using Omnitron s standard shipping method Limitation of Warranty The foregoing warranty shall not apply to defects resulting from improper
Download Pdf Manuals
Related Search