Chief PAC720 flat panel floorstand
Contents
1. 5 16 18 x 3 4 720 Installation Instructions ASSEMBLY AND INSTALLATION WARNING EXCEEDING MAXIMUM WEIGHT CAPACITY MAY LEAD TO SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT It is the installer s responsibility to ensure the total amount of weight placed on the cart stand does not exceed 200 Ibs 90 72 kg for the PFC 200 Ibs 90 72 kg for the PF1 400 Ibs 181 44 kg for the PF2 200 lbs 90 72 kg per faceplate Installing Display s to Cart Stand 1 Install display s to cart or stand following the installation instructions included with the cart stand Assembling Faceplate to Bracket 1 Attach faceplate A to bracket B using two 3 8 16 Nylock lock nuts E See Figure 1 Figure 1 2 Secure faceplate with bracket around postto clamp bracket C using four 5 16 18 x 3 4 buttonhead cap screws D NOTE The faceplate assembly must be attached to the clamp bracket below the knob on the lower part of the cart stand post PAC720 must be installed BELOW the knob located on the post back Figure 2 Assembly for Dual Display WARNING TIPPING HAZARD Place PAC720 only on FRONT of PFC and PF1 PAC720 may be placed on both FRONT and BACK of PF2 1 Attach first faceplate A to bracket B using two 3 8 16 Nylock lock nuts E See Figure 1 2 Attach second faceplate A to bracket B using two 3 8 16 Nylock lock2. align four mounting buttons on display or interface bracket with four mounting holes in faceplate See Figures 5 and 6 A padlock or bolt may be placed through latch holes Figure 6 3 To adjust location of display on cart stand support display s and carefully loosen four 5 16 18 x 3 4 buttonhead cap screws D on each faceplate assembly 720 must be 4 Slide display s up on post to desired position and tighten installed BELOW four 5 16 18 x 3 4 buttonhead cap screws D for each the knob located faceplate assembly See Figures 2 and 4 7 on the post back 5 Refer to the installation instructions provided with the cart stand for further information on Tilting Display Removing Display Cable Management and Cart Stand Maintenance WARNING EACH DISPLAY MAY WEIGH IN EXCESS OF 720 Installation Instructions CHIEF 8832 000231 2007 Chief Manufacturing www chiefmfg com 07 07 USA International Europe Asia Pacific T Uu 8401 Eagle Creek Parkway Savage MN 55378 800 582 6480 952 894 6280 877 894 6918 952 894 6918 Fellenoord 130 5611 ZB EINDHOVEN The Netherlands 31 40 2668620 31 0 40 2668615 Room 301 Block Lily YinDu International Building LuoGang BuJi Town Shenzhen CHINA Post Code 518112 RAI 45 E 27 KAS 6 ESL E AB DFO 86 755 8996 9226 8996 9
3. nuts E See Figure 3 Figure 3 3 Secure faceplate assemblies with bracket to clamp brackets C onto cart stand post using four 5 16 18 x 3 4 buttonhead cap screws D on EACH assembly See Figure 4 Installation Instructions PAC720 NOTE The faceplate assembly must be attached to the clamp 40 LBS Always use two people and proper lifting techniques bracket below the knob on the lower part of the cart when installing or positioning display on stand stand post 2 Lower display into place listening for audible click to ensure recessed area of mounting buttons are properly seated in lower area of mounting holes See Figures 5 and 6 WARNING IMPROPER INSTALLATION CAN LEAD TO CART STAND OR DISPLAY FALLING CAUSING SERIOUS D x4 PERSONAL INJURY OR DAMAGE TO EQUIPMENT Ensure mounting buttons are completely engaged in mounting holes PAC720 must be installed BELOW the knob located on the post back NOTE Holes are provided in the faceplate for use with a padlock or similar locking device if desired In addition the pin and nut may be removed from the upper holes and moved to the lower holes for use as a more permanent locking device See Figure 6 E Remove pin 2 and nut and move to lower holes PF2 shown Figure 4 Attaching Display 1 While supporting both sides of display
4. 236 8996 9220 86 755 8996 9217
5. INSTALLATION INSTRUCTIONS Cart and Stand Clamp Head Accessory CHIEF PAC720 720 Installation Instructions DISCLAIMER CSAV Inc and its affiliated corporations and subsidiaries collectively CSAV intend to make this manual accurate and complete However CSAV makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind CSAV makes no representation of warranty expressed or implied regarding the information contained herein CSAV assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document A IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations WARNING Failure to read thoroughly understand and follow all instru
6. ctions can result in serious personal injury damage to equipment or voiding of factory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components on the cart stand does not exceed 200 lbs 90 72 kg for the PFC 200 Ibs 90 72 kg for the PF1 400 Ibs 181 44 kg for the PF2 200 Ibs 90 72 kg per faceplate Hex Head Wrench Llave de cabeza hexagonal Sechskantschlissel Chave de cabe a sextavada Chiave esagonale Zeskantsleutel Cl a t te hexagonale Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis a pointe cruciforme Installation Instructions PAC720 TOOLS REQUIRED FOR INSTALLATION AND PARTS J 3 16 Provided D 4
Download Pdf Manuals
Related Search