Home

Cisco Catalyst Switch Module 3110X

1. CHAPTER 1 Product Overview The Cisco Catalyst Switch Module 3110G 3110X and 3012 for IBM BladeCenter referred to as the switch modules are Ethernet switch modules that you install in an IBM BladeCenter enclosure referred to as the blade enclosure You can connect devices to the switch modules for connections to other network devices such as routers servers and other switches The Catalyst Switch Module 3110G and 3110X support stacking through Cisco StackWise Plus technology The Catalyst Switch Module 3012 does not support stacking Unless otherwise noted the term switch module refers to a standalone switch module and to a switch stack Note This product is not intended to be connected directly or indirectly by any means whatsoever to interfaces of public telecommunications networks This chapter provides a functional overview of the switch modules and covers these topics e Switch Modules page 1 1 e Hardware Features page 1 2 e Management Options page 1 9 Switch Modules Table 1 1 describes the switch modules Table 1 1 Catalyst Switch Module 3110G 3110X and 3012 Switch Model Cisco Part Number IBM Part Number Description CatalystSwitch WS CBS3110G S WS CBS3110G S I 4 external 10 100 1000BASE T Module 3110G Ethernet ports 14 internal 1000BASE X Ethernet downlink ports 1 internal 1JOOBASE T Ethernet management port 2 StackWise Plus ports I OL 12192 01 Catalyst Switch Modu
2. Guide OL 12192 01 Chapter1 Product Overview Hardware Features W The Catalyst Switch Module 3012 includes the 10 100 1000 Ethernet ports console port release latch and the switch module LEDs shown in Figure 1 2 and described on the following pages Figure 1 2 Catalyst Switch Module 3012 270430 1 Catalyst Switch Module 3012 4 Switch module LEDs 2 Console port 5 10 100 1000 Ethernet ports 3 Mode button 6 Release latch 10 100 1000 Ethernet Ports The Catalyst Switch Module 3110G and 3012 10 100 1000 Ethernet ports use standard RJ 45 connectors with Ethernet pinouts The maximum cable length is 328 feet 100 meters The 1OOBASE TX and 1000BASE T traffic requires Category 5 Category 5e or Category 6 unshielded twisted pair UTP cable The 1OBASE T traffic can use Category 3 or Category 4 UTP cable For information about the 10 100 1000 Ethernet port connections and specifications see the Connecting Devices to the Ethernet Ports section on page 2 13 and Appendix B Connector and Cable Specifications Catalyst Switch Module 3110G 3110X and 3012 for IBM BladeCenter Hardware Installation Guide oL 12192 01 EEN Chapter1 Product Overview WE Hardware Features 10 Gigabit Ethernet Module Slot The Catalyst Switch Module 3110X 10 Gigabit Ethernet module slot is used for an uplink connection to other switches and routers The module slot operates in full duplex mode
3. by STP and is not forwarding data or port was administratively shut down Alternating Link fault green amber Catalyst Switch Module 3110G 3110X and 3012 for IBM BladeCenter Hardware Installation Guide OL 12192 01 Chapter1 Product Overview Management Options W When stack mode is selected on a Catalyst Switch Module 3110X the two port status LEDs show the status for Stack Wise Plus ports 1 and 2 respectively Table 1 11 lists the LED colors and their meanings Table 1 11 Catalyst Switch Module 3110X Port Status LEDs with Stack Mode Selected Color Port Status LED Description Off No link Green Switch stack link is active StackWise Plus Ports A The switch module ships with a 1 meter Stack Wise Plus cable that you can use to connect the Stack Wise Plus ports only Catalyst Switch Module 3110G and 3110X Caution Console Port Use only approved cables and connect only to Catalyst Switch Module 3110G and 3110X Equipment might be damaged if connected to nonapproved Cisco cables or equipment You can order these StackWise Plus cables from your supplier e CAB STK E 0 5M 0 5 meter cable e CAB STK E 1M l meter cable e CAB STK E 3M 3 meter cable You can connect the switch module to a host such as a PC workstation or a terminal server through the console port shown in Figure 1 1 Use the supplied USB to DB 9 cable to connect the switch module to a host For more informat
4. BM Intel processor based servers desktop computers workstations and mobile computers on a variety of platforms See the IBM documentation for more information Device manager You can use the device manager which is in the switch module memory to manage standalone switch modules and switch stacks This web interface offers quick configuration and monitoring You can access the device manager from anywhere in your network through a web browser For more information see the getting started guide and the device manager online help Cisco Network Assistant Cisco Network Assistant is a PC based network management GUI application optimized for LANs of small and medium sized businesses Cisco Network Assistant offers centralized management of Cisco switches ranging from the Catalyst Express 500 through the Cisco Catalyst 4506 Through a GUI users can configure and manage standalone switch modules and switch stacks Cisco Network Assistant is available at no cost and can be downloaded from this URL http www cisco com go cna_doc For information on starting the Network Assistant application see the Getting Started with Cisco Network Assistant guide on Cisco com SNMP network management You can manage switch modules from a SNMP compatible management station The switch module supports a comprehensive set of Management Information Base MIB extensions and four Remote Monitoring RMON groups See the switch module software configuration gu
5. and uses the hot swappable Cisco X2 transceiver modules The X2 transceiver modules have a dual SC PC connector SR LX4 or an Infiniband 4x connector CX4 for connections to multimode fiber MMF single mode fiber SMF or 4x Infiniband cable These are the supported Cisco X2 transceiver modules e X2 10GB SR e X2 10GB CX4 e X2 10GB LX4 For information about installing a transceiver module see the Installing Devices in the 10 Gigabit Ethernet Slot section on page 2 11 For cable specifications see Appendix B Connector and Cable Specifications Port Numbering Table 1 2 describes the switch module port numbering Table 1 2 Switch Module Port Numbering Port Description Ports 1 to 14 Internal Gigabit Ethernet 1000BASE X downlink ports that connect to the blade enclosure Ports 15 to 18 Catalyst Switch External 10 100 1000BASE T copper Gigabit Ethernet uplink ports Module 3110G and 3012 Port X2 Catalyst Switch External 10 Gigabit Ethernet module slot Module 3110X 1 The number of internal ports is determined by the blade enclosure model See the blade enclosure documentation for more information about internal port numbering Internal 100BASE T Ethernet Management Port The internal Ethernet management port Fa0 is used only for switch module management traffic not for data traffic It is connected to the IBM advanced Management Module aMM through the blade enclosure backplane c
6. h Module 3110G and 3110X To select or change a mode use a small pointed object to press the Mode button until the desired mode is selected System Power LED The system power LED shows whether the system is receiving power and is functioning properly Table 1 3 lists the LED colors and their meanings Table 1 3 System LED Color System Status Off Switch module is not powered on Green Switch module is operating normally Amber Switch module is receiving power but is not functioning properly Blinking green Switch module is running the power on self test POST Stack Master LED The stack master LED shows the stack master status Table 1 4 lists the LED colors and their meanings only Catalyst Switch Module 3110G and 3110X Table 1 4 Stack Master LED Color Description Off Switch module is not the stack master Green Switch module is the stack master or a standalone switch Amber An error occurred during stack master election or another type of stack error occurred Catalyst Switch Module 3110G 3110X and 3012 for IBM BladeCenter Hardware Installation Guide OL 12192 01 Chapter1 Product Overview Hardware Features W Fault Stack Mode LED The fault stack mode LED shows either a fault condition or the switch stack status depending on the Mode button selection When the switch module is not stacked and there is no fault the LED is off If the switch module is stacked and the stack mode LED is selected
7. ide on Cisco com and the documentation that came with your SNMP application for more information CiscoWorks application The CiscoWorks device management application displays the switch module image that you can use to set configuration parameters and to view switch module status and performance information The CiscoView application which you purchase separately can be a standalone application or part of a Simple Network Management Protocol SNMP platform See the CiscoView documentation for more information Network Configurations See the switch module software configuration guide on Cisco com for network configuration concepts and examples of using the switch module to create dedicated network segments and interconnecting the segments through Gigabit Ethernet connections Catalyst Switch Module 3110G 3110X and 3012 for IBM BladeCenter Hardware Installation Guide OL 12192 01
8. ion about the console port see the switch module getting started guide the software configuration guide and the command reference on Cisco com Management Options The switch module offers several management options e Cisco IOS CLI The switch module command line interface CLI is based on Cisco IOS software and is enhanced to support desktop switching features You can fully configure and monitor the switch module and switch stack members from the CLI You can access the CLI by connecting your management station directly to the switch module console port or by using Telnet from a remote management station See the switch module getting started guide the software configuration guide and the command reference on Cisco com for more information e BladeCenter Advanced Management Module For standalone switch modules you can use the aMM to configure the switch module See the JBM BladeCenter Advanced Management Module User s Guide for more information For stacked switches use the CLI to configure and manage the switch stack I OL 12192 01 Catalyst Switch Module 3110G 3110X and 3012 for IBM BladeCenter Hardware Installation Guide Chapter1 Product Overview W Management Options IBM Director For standalone switch modules you can use the IBM Director to view the hardware configuration of remote systems monitor the usage and performance of critical components centrally manage individual or large groups of IBM and non I
9. le 3110G 3110X and 3012 for IBM BladeCenter Hardware Installation Guide jg Chapter1 Product Overview WE Hardware Features Table 1 1 Catalyst Switch Module 3110G 3110X and 3012 continued Switch Model Cisco Part Number IBM Part Number Description Catalyst Switch WS CBS3110X S WS CBS3110X S I 1 external 10 Gigabit Ethernet module Module 3110X slot 14 internal 1000BASE X Ethernet downlink ports 1 internal 100BASE T Ethernet management port 2 StackWise Plus ports Catalyst Switch WS CBS3012 IBM WS CBS3012 IBM I 4 external 10 100 1000BASE T Module 3012 Ethernet ports 14 internal 1000BASE X Ethernet downlink ports 1 internal 100BASE T Ethernet management port Hardware Features The Catalyst Switch Module 3110G and 3110X include the 10 100 1000 Ethernet ports or the 10 Gigabit Ethernet module slot console port Stack Wise Plus ports release latch and the switch module LEDs shown in Figure 1 1 and described on the following pages Figure 1 1 Catalyst Switch Module 3110G and 3110X 201895 Catalyst Switch Module 3110G 10 100 1000 Ethernet ports Catalyst Switch Module 3110X Switch module LEDs 10 Gigabit Ethernet module slot Mode button oo N co Stack Wise Plus ports Console port oa fF OO N Release latch 1 For use with Cisco X2 transceiver modules Catalyst Switch Module 3110G 3110X and 3012 for IBM BladeCenter Hardware Installation
10. onnector Traffic to and from this port is isolated from the switch module ports This port only supports autonegotiation with 100 Mb s and full duplex mode Catalyst Switch Module 3110G 3110X and 3012 for IBM BladeCenter Hardware Installation Guide mia g OL 12192 01 _ Chapter 1 Product Overview Switch Module LEDs Figure 1 3 1 stack 2 ful 4el Hardware Features You can use the switch module LEDs to monitor switch module activity Figure 1 3 shows the switch module LEDs and the Mode button that you use to activate the different modes Switch Module LEDs and Mode Button STACK 2 Stack member LED 8 Stack member LED Catalyst Switch Module 3110G Mode button 9 Mode button Fault stack mode LED 10 Fault stack mode LED Catalyst Switch Module 3110G Fault LED Catalyst Switch Module 3012 System power LED 11 System power LED Stack master LED 12 Stack master LED Catalyst Switch Module 3110G Port link LED 13 X2 port status LEDs Port activity LED I OL 12192 01 Catalyst Switch Module 3110G 3110X and 3012 for IBM BladeCenter Hardware Installation Guide Chapter1 Product Overview WE Hardware Features Mode Button The fault stack or stack member LEDs are selected by using the Mode button If the mode LED for a particular mode is solid green that mode is currently selected and the other mode LEDs are off only Catalyst Switc
11. talyst Switch Module 3110G and 3012 port LEDs show interface activity and link status Table 1 8 lists the LED colors and their meanings Table 1 8 Catalyst Switch Module 3110G and 3012 Port LEDs Activity LED Color Link Status LED Color Description Off Off No link or port was administratively shut down Off Green Link present or the port might be blocked by Spanning Tree Protocol STP and is not forwarding data Blinking green or off Blinking green Activity Port is sending or receiving data When stack mode is selected on a Catalyst Switch Module 3110G port 4 activity and link LEDs show the status for Stack Wise Plus ports 1 and 2 respectively The other port LEDs are off Table 1 9 lists the LED colors and their meanings Table 1 9 Catalyst Switch Module 3110G Port LEDs with Stack Mode Selected Color Activity LED Description Link Status LED Description Off No link No link Green Switch stack link is active Switch stack link is active The Catalyst Switch Module 3110X port status LEDs show interface activity and link status The LEDs combine to display status when an X2 transceiver is inserted Table 1 10 lists the LED colors and their meanings Table 1 10 Catalyst Switch Module 3110X Port LEDs Color LED Description Off No link or port was administratively shut down Green Link present Blinking green Activity Port is sending or receiving data Amber Port is blocked
12. the stack member LED is active Table 1 5 lists the LED colors and their meanings only Catalyst Switch Module 3110G and 3110X Table 1 5 Fault Stack Mode LED Color Fault Mode Description Stack Mode Description Off No switch module faults Stack mode is not selected Green Switch stack mode is selected When this LED is green the stack member LED displays the stack membership number and the port LEDs display link status Amber Switch module fault detected Fault LED The fault LED shows the switch module fault condition Table 1 6 lists the LED colors and their meanings only Catalyst Switch Module 3012 Table 1 6 Fault LED Color Fault Mode Description Off No switch module faults Amber Switch module fault detected Stack Member LED The stack member LED is active when the switch module is stacked and you select by using the Mode button The stack member LED blinks the number of times equal to the switch stack membership number Table 1 7 lists the LED colors and their meanings only Catalyst Switch Module 3110G and 3110X Table 1 7 Fault Stack Mode LED Color Description Off Stack mode is not selected or the switch module is not stacked Blinking green Stack member number Catalyst Switch Module 3110G 3110X and 3012 for IBM BladeCenter Hardware Installation Guide oL 12192 01 EN Chapter1 Product Overview WE Hardware Features Port LEDs The Ca

Cisco Catalyst Switch Module 3110X

Contents

Download Pdf Manuals

Related Search

Related Contents