Datamax O'Neil OPT78-2697-01
Contents
1. O Neil FTP site at ftp datamax oneil com Once you have downloaded and installed the DMXConfig utility 1 Connect the host to the printer with a serial or parallel cable 2 Turn on the printer 3 Launch the DMXConfig utility 4 Query the printer by using the Query Printer toolbar button top left This will connect to the printer and get the current printer settings 5 Next select the Media Settings tab in the Media Type drop down box select Thermal Transfer 6 Send the settings to the printer using the Configure Printer toolbar button Once the previous steps have been successfully completed you may now print using ribbon If you wish to revert to printing without ribbon Direct Thermal you will have to repeat this procedure and select the Direct Thermal setting from the drop down box alli ee ae Fontar Modat 00 1000 USZACOO ar Prete Moda Settinas User Functions Host Connection Syutum Sutinoz Sensor Calbeaton Pant Carol Communications Printer Options Memory Modules viario bole ay bs weed Wore placate ag Senne gg Fa wem De puede 2 ending Commune ad A A A aan aerate Me tot he accropnate parte modes and modiy he corfipaston as necessary hen cortas the prim See HELP kx more dead Paidos Posts a Dama HIN alal D eo w oe a Printew Meinl 171205 5 081 02 03 04 Configure Printer Button Media Settings Usar Fun2. inked side of the ribbon faces the media and NOT the printhead To load ribbon For more information on ribbon load refer to the Operator s Manual O Slide a ribbon completely onto the Supply Hub so that the ribbon s leader will be oriented according to the Supply Hub type CSI or CSO O Depending upon the ribbon type route the ribbon over or under the Guide Shaft as shown below Continue routing the ribbon under the Ribbon Idler then raise the Printhead Mechanism and bring the ribbon over the platen roller O Extend about 12 inches 30 cm of ribbon out the front of the printer and then close the Printhead Mechanism O Bring the ribbon up to the Take Up Hub Tape the leader to the Take Up Hub Wind the hub clockwise several times to remove any slack Ribbon Loading Diagrams Coating Side In Routing Coating Side Out Routing Setup and Configuration non display models DMXConfig is a windows based configuration utility that allows the user to make changes to the existing printer setup via a direct connection to the host computers serial and parallel connection If you wish to use DMXConfig to configure your printer please download the latest version from the Datamax
3. 92 2480 01 Rev C right by our customers datamax oneil Contents of the Thermal Transfer Kit This kit contains the following items Thermal Transfer Assembly Screws 3 Follow the steps listed below to install this option Tools Required To install this option you will need a 2 Phillips head screwdriver Step 1 Preparing the Printer O Turn Off the power switch and unplug the printer Open the cover Remove any installed media from the printer Remove the three Screws that Cover Plate secure the Cover Plate to the printer _ 2 TO Be t oL O Remove the Cover Plate Screws A 5 2 S 2 gt 2 0 Step 2 Installing the Thermal Transfer Assembly Thermal Transfer Assembly Carefully position the Thermal Transfer Assembly into the Centerplate of the printer as ___ e g shown E o Screws L a 2 wr O Secure the Thermal Transfer 2 Assembly using the three 0 Screws supplied in this kit Centerplate This completes the installation process Proceed to Ribbon Loading and Setup and Configuration Ribbon Loading M Notes Directional Arrows near the Ribbon Supply Hub indicate the correct ribbon route Ribbon types are available with the ink coating layer wound in or out These types are interchangeable for use with the printer Ensure the
4. cicas Host Connection Smam Sennor Sensor Colibrarc Print Control Communications Printer Options Mamory Modules Madia Type Sansor Type Com Form Length m 1003 Label Width fn re Setup and Configuration display models In order to use thermal transfer printing the Media Type menu function must be set to Ribbon Transfer Follow the steps below to set the printer to Thermal Transfer 7 Note The DMXConfig Utility can also be used to change the Media Type setting For more information see the previous section Setup and Configuration non display models Configure the printer for the thermal transfer use as follows O Plug the power cord into the AC Receptacle and turn On the Power Switch O Press the MENU Button on the printer s front panel Press the ENTER Key to select MEDIA SETTINGS and press the key again to select MEDIA TYPE O Using the DOWN Button scroll to THERMAL TRANSFER then press the ENTER Key O Press the EXIT Key and then at the SAVE CHANGES prompt press the YES Key Unloading the Thermal Transfer Assembly When the ribbon supply has been emptied simply pull the cardboard core off the Supply Hub To remove the used ribbon grasp the ribbon and pull it from the Take Up Hub
Download Pdf Manuals
Related Search