Home
        KRAM Audio2Car Premium
         Contents
1.    Radio   Radio Spk Spk Spk Spk  Out L    Out R    RR  RF  LF  LR  LR  LF  RF  RR     Connector seen from cable entry side    EN104 V01          Audio ZCar    The professional mute    Installation description   for 84604 Audio2Car harness used for  Mercedes cars with D2B bus and sound  system upgrade     Bullet Connectors     gt     A  Audio2Car Harness    Needed items   Item number 84xxx    A  Audio2Car harness including Mute box  amp  Mute loop   B  Audio2Car extension cable  bought separately     C  Audio2Car carkit adaptor  bought separately     D  Carkit  bought separately      24 pin Connectors    B  Audio2Car Extension    Note  B  amp  C can be replaced by an additional Mute box and   Cable Item number AEx    extension cable from our Drive  amp  Talk range   24 pin Connectors  gt     Identification of sound system  ute loop  This cable will only fit cars equipped with sound system    upgrade often referred to as option code 810  It will not fit        Audio2Car Adaptor     gt   the standard sound system  Please see our complete cable   Item number AAxxx   list for further information about choosing the right cable  for your sound system  The list can be downloaded at  www kram dk    D  Carkit    Installation   When delivered this Audio2Car cable set is always fitted  with a Mute box and a Mute loop connector     1st  Remove the key from the ignition barrel  This is  done to avoid error messages on the cars electrical system   Such error can only be reset by an authori
2.  Audio2Car cable should not be bigger than the ones used on the wiring loom  supplied with the carkit  The fuses on the Audio2Car cable should be replaced with a size similar to the ones supplied  with the carkit    Note  Never exceed the Maximum Fuse size for the Audio2Car cable  See first page     6th  Extend the cable set to the preferred location of the carkit  Use the extension cable B  or additional Drive  amp   Talk Mute box with extension cable  to extend the cable set to the preferred location of the carkit  Behind the glove   box is recommended     7th  Connect the carkit adaptor  Connect the carkit adaptor to the extension cable  Connect the carkit adaptor to the  carkit     Troubleshooting Guide    Carkit does not start up  Check if there is 12V between the black and the red wire and also between the black and  blue wire  in the 24 pin connector  when the car is started  If there is not 12v on both wires please check the follow     ing     1  If there is supply on the red constant 12v wire but not on the blue ignition wire the car may require an  alternative ignition source  See installation step 4    2  Check that the bullets on the supply wires are properly connected  The supply wires are the red  blue and  black wires    3 Check for a blown fuse on the Audio2Car harness or in the cars fuse box     The carkit does not turn off when the key is removed from the ignition barrel  Your carkit needs a real ignition   source  Please check the following    1  Is there a
3. Audio ZCar    The professional mute    Audio2Car harness    For a complete installation normally a minimum of two item numbers are re   quired    Audio equipment with build in mute function    If the Audio equipment is equipped with a build in mute function two item numbers  are required  The 1st item number is the Audio2Car harness  The 2nd item is a  Audio2Car carkit adaptor    Audio equipment without build in mute function    If the Audio equipment is not equipped with speaker relays  a Mute box from Kram  Drive  amp  Talk range can be added together with a Drive  amp  Talk carkit adaptor     Audio2Car Carkit Adaptors    Several different carkit adaptors  are available for Carkits that  have a build in mute function  for 1 or 4 Speakers    Please see the complete range  of Audio2Car carkit adaptors   at our website    www kram dk    Examples of  carkit adaptors    Drive  amp  talk Mute box  range    SS Several different   P types of mute boxes  are available  Adding   one of the boxes will  turn your Audio2Car  cable into a Kram  Drive  amp  Talk solution   Therefore you will  also need a Drive  amp   Talk carkit adaptor   Please see the Com   plete Drive  amp  Talk  range at our website   www kram dk    This ISO adaptor AA010 is a     This IGNIBOX ITEM no     1     universal adaptor for all creates an artificial ignition  carkits with ISO connectors      source  Use this adaptor if  Adding this adaptor turns your Audio2Car cable does  your Audio2Car cable into a     not i
4. n ignition supply on the blue wire  There should be no voltage on the blue wire when there is no  key in the ignition  See installation step 4    Not all speakers are muted  Try to disconnect the Mute box and the Carkit adaptor C  or additional Drive and Talk   mute box  from the Audio2Car harness then turn on the radio and check the following      1  All front door speakers keep playing  This is the wrong Audio2Car harness for this car   sound system   2  A few speakers keep playing  This is the wrong Audio2Car harness for this car   sound system   3  All speakers are now muted    e Carkits with 1 speaker mute  Some carkits can only mute 1 speaker channel with their build in    mute box  This is normally stated on the label on the carkit adaptor for these carkits  else please  check the carkit manual  If a full mute is desired with these carkits  then this can be achieved by  either connecting the mute wire or adding an additional mute box from our Drive  amp  Talk range     e Carkits with 4 speaker channel mute   or when additional Drive  amp  Talk mute box is used   Please  check that the    Mute Loop    is attached to Mute box delivered with the cable set  Else please try  another carkit    Carkit sound is in the wrong speakers or there is no carkit sound     1  The two 24 pin connectors in the cable set may be switched  The carkit should be connected to the 24 pin  connector with the Green  White  Gray and Purple wires    2  The carkit may be defective  Please try anothe
5. nclude an ignition source   Kram ISO2CAR solution  This adaptor is plug and play  with your Audio2Car cable     Audio ZCar    The professional mute    Product Description    The Audio2Car range allows OEM car speakers to be used for aftermarket Audio equipment     Audio2Car allow the car speakers to be used for audio playback from aftermarket Audio equipment  For a com   plete installation two or more item numbers are required  See description at the last page     Speaker function  This is achieved by connecting Audio equipment with build in speaker relay function or by  using a Mute box from the Kram range  This way the radio sound is muted and the sound from the aftermarket  Audio equipment is sent through the car speakers  You will achieve a perfect sound without interference from  the car radio    Mute wire function  The mute wire is connected from the 24 pin connector to the most used mute position for  the car model  This enables the use of the radios built in mute function  If the radio does not have such function  or the mute exists in a different connector than the ones used on the Audio2Car harness  the mute wire can be  found in a yellow fly wire fitted with a bullet connector    Power supply  All Audio2Car cables have an integrated power supply for the Audio equipment in the 24 pin  connector  The constant 12v and the ground supply are normally sourced from the radio supply  This way power  supply of most Audio Equipment can be achieved without cutting the cars wi
6. r carkit    Radio will not turn on or not working properly after installation    1  Please check for a blown fuse at the radio or in the car fuse box    2  Remove the Audio2Car harness and connect the radio to the original car connector  If the radio is now work     ing replace the Audio2car harness     See our complete Radio Mute program on our website www kram dk       
7. ring loom  The constant 12V wires  are red and the ground wires are black    Ignition supply  If an ignition source is available in the radio connector then it will normally also be available in  the 24 pin connector  If an ignition source is not available a constant 12V source is connected to the Ignition pin  via bullet connectors  If a real ignition is required for the chosen Audio Equipment  an IGNIBOX item no     I    can    be connected to create an artificial ignition  Or an ignition source found elsewhere can be connected to the  bullet with the blue wire  The 12V ignition wires in the Audio2Car cable are blue     Aux integration  The 4 pin connector on the Audio2Car harness allow a Kram Aux solution to be connected  This will allow the    use of the car sound system amplifier for Music playback and thereby achieving higher sound quality     Technical Specifications    Description  L shaped with bullet connections for Ground  Constant 12v and Ignition   Normal Wire dimensions   AWG 18 for power wires  AWG 20 for all other wires   Standard Fuse sizes  2 Amp for constant supply  1 Amp for Ignition supply   Maximum Fuse size  7 5 Amp for constant supply  7 5 Amp for Ignition supply   Maximum output pr  speaker  100 Watt RMS   200 Watt music power   4 Ohm   Size  400 x 400 mm    Configuration chart for 24 pin connector   12V 12V Line Line Radio   Radio Radio Radio Spk Spk Spk Spk  Const    IGN Out L    Out R    RR  RF  LF  LR  LR  LF  RF  RR   Mute Line Line Radio   Radio
8. sed Mercedes  Repair shop     2nd  Locate  amp  uncover the amplifier unit  Amplifier  locations     e CL Class C215  M Class W163  S Class W220  install on amplifier in the left side of the boot  An  Audio2Car extension cable item no  AE5 is also  required     e C Class W203  CLK Class W209 install on ampli   fier in the right side of the boot just behind right  wheel arc  An Audio2Car extension cable item no   AES is also required     e M Class W163 install on amplifier inside driver  side dashboard towards the door  An Audio2Car  extension cable item no  AE3 may also be re   quired depending on the chosen position of the  carkit  See picture on the right     o SL Class R230 install on amplifier below left rear  passenger seat  See picture on the right     3rd  Connect the car specific cable  Disconnect the con   nector on the amplifier unit and insert the Audio2Car har   ness between the connector and amplifier unit     Ath  Check ignition source  When the cable set is deliv   ered the blue ignition wire is connected to the red constant  12V wire with a bullet connector  If a real ignition source is    needed for the chosen carkit an IGNIBOX item no     I    can Ampiner iocalion IN Metee aceon aes R230       Audio ZCar    The professional mute       be inserted to create an artificial ignition source or the blue ignition wire can be disconnected from the red constant  12v and manually connected to an ignition source found elsewhere     5th  Check fuse size  The fuse on the
    
Download Pdf Manuals
 
 
    
Related Search
    
Related Contents
Installer une plaque de cuisson mixte  OWNER`S MANUAL  Tuberías de PVC: Manual técnico  ES7000 User Manual    E:\维修手册\W97055A3\97055 Service Manual  MANUAL DE INSTRUCCIONES PICADORA 1-2-3  「1/2400スケール 東京スカイツリー」2011年6月11日(土)  Manual - morganti  Video User's Guide    Copyright © All rights reserved. 
   Failed to retrieve file