IBM Brocade Enterprise SAN Switch Module
Contents
1. 45W0505 e Fabric Watch 45W0504 e Adaptive Networking 45W0510 Note Server Application Optimization is not available for the 10 port and 20 port modules Supported BladeCenter chassis and expansion cards Brocade 8Gb SAN Switch Modules are supported in the IBM BladeCenter chassis as listed in Table 3 im 7 a i a m I O module Part number Brocade Enterprise 20 port 8Gb SAN Switch Module 42C 1828 Brocade 20 port 8Gb SAN Switch Module 44X1920 Brocade 10 port 8Gb SAN Switch Module 44X1921 t BladeCenter T can be supported on a case by case basis after testing the specific configuration Contact your IBM representative When the I O module is installed in a BladeCenter HT unit the internal ports operate up to 2 Gbps and the external ports operate at speeds up to 8 Gbps Table 3 IBM BladeCenter chassis that support the Brocade 8 Gb SAN Switch Modules T un E BladeCenter HT Ta k im k a OW o 9 a a Ez L L co cS The Brocade 8Gb SAN Switch Modules support the expansion cards listed in Table 4 Table 4 also lists the chassis bays in which the switch module must be installed when used with each expansion card The BladeCenter chassis have the following bays e BladeCenter S E and T have four standard I O bays 1 2 3 and 4 e BladeCenter H has four standard I O bays 1 2 3 and 4 two bridge bays 5 and 6 and four high speed bays 7 8 9 and2. The furnishing of this document does not give you any license to these patents You can send license inquiries in writing to IBM Director of Licensing IBM Corporation North Castle Drive Armonk NY 10504 1785 U S A The following paragraph does not apply to the United Kingdom or any other country where such provisions are inconsistent with local law INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS PUBLICATION AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF NON INFRINGEMENT MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE Some states do not allow disclaimer of express or implied warranties in certain transactions therefore this statement may not apply to you This information could include technical inaccuracies or typographical errors Changes are periodically made to the information herein these changes will be incorporated in new editions of the publication IBM may make improvements and or changes in the product s and or the program s described in this publication at any time without notice Any references in this information to non IBM Web sites are provided for convenience only and do not in any manner serve as an endorsement of those Web sites The materials at those Web sites are not part of the materials for this IBM product and use of those Web sites is at your own risk IBM may use or distribute any of the information you supply in any way it beli
3. ul ye Redbooks web Doc Brocade Enterprise 20 port 20 port and 10 port 8Gb SAN Switch Modules IBM BladeCenter at a glance guide The Brocade Enterprise 20 port 20 port and 10 port 8 Gb SAN Switch Modules for IBM BladeCenter deliver embedded Fibre Channel switching with the industry s fastest Fibre Channel throughput performance 8 Gbps The 20 port and 10 port switches provide basic FC switch functionality while the Enterprise 20 Port model is a fully enabled switch with a complete set of advanced SAN fabric service licensed features Figure 1 shows the Brocade 8Gb SAN Switch Module Figure 1 Brocade 8Gb SAN Switch Module for IBM BladeCenter Did you know Brocade 8Gb SAN switches operate in full fabric switch mode for native interoperability with IBM System Storage b type SAN switches and Brocade Access Gateway mode for industry standard interoperability with any fabric that supports N_ Port ID Virtualization NPIV technology Brocade Enterprise 20 port 20 port and 10 port 8Gb SAN Switch Modules 1 Part number information Table 1 shows the part numbers to order these modules Table 1 Part numbers and feature codes for ordering Description Feature code Brocade Enterprise 20 port 8Gb SAN Switch Module for IBM BladeCenter 42C 1828 5764 Brocade 20 port 8Gb SAN Switch Module for IBM BladeCenter 44X1920 5481 Brocade 10 port 8Gb SAN Switch Module for IBM BladeCenter 44X1921 5483 Brocade 10 port Upgrade f
4. 10 e BladeCenter HT has four standard I O bays 1 2 3 and 4 and four high speed bays 7 8 9 and 10 The Brocade 8Gb SAN Switch Modules fit in a standard I O bay bays 1 6 and with the addition of the Multi Switch Interconnect Module MSIM in the BladeCenter H can also fit in a high speed I O bay bays 7 10 The Brocade 8Gb SAN Switch Modules are not supported with MSIM HT in high speed bays of the BladeCenter HT chassis Brocade Enterprise 20 port 20 port and 10 port 8Gb SAN Switch Modules 5 Table 4 Expansion card support and Chassis I O bay support Part T p oo a a os os a 8Gb expansioncars SS EEREN N N Standard a Standard a Standard mi Standard Bay 5 Bridge Y N i a oS oa gt m m oo QLogic Ethernet and 8 Gb Fibre Channel er N Expansion Card CFFh QLogic 8Gb Fibre Channel Expansion Card CIOv QLogic 8Gb Fibre Channel Expansion Card CIOv Fibre Channel Expansion Card ClOv 44X1945 aa a N N N N N Emulex 8Gb Fibre Channel Expansion Card ClOv 46M6140 seen R REIRO 1Gb expansion car es QLogic 4 Gb SFF FC Expansion Card zeros00 N N el N NINI NINN QLogic 4 Gb Fibre Channel Expansion Card CFFv 41Y8527 Emulex 4 Gb Fibre Channel Exp Gard GFFv 4306855 OO ECCI QLogic 4 Gb Fibre Channel Expansion Card ClOv 46M6065 N QLogic Ethernet and 4 Gb Fibre Channel sei Expansion Card CFFh Note When the I O module is ins
5. 884 e Supplemental Instructions Installing a Brocade 8Gb SAN Switch Module for IBM BladeCenter with a multi switch interconnect module MSIM http www ibm com support docview wss uid psg 1MIGR 5081558 e IBM US Announcement Letter http ibm com common ssi cgi bin ssialias infotype dd amp subtype ca amp amp htmlfid 89 7 ENUS 109 592 e BM BladeCenter Interoperability Guide http www ibm com support docview wss uid psg 1MIGR 5073016 e IBM Redbooks publication BM BladeCenter Products and Technology SG24 7 523 http www redbooks ibm com abstracts sg24 523 html Brocade Enterprise 20 port 20 port and 10 port 8Gb SAN Switch Modules 10 Notices This information was developed for products and services offered in the U S A IBM may not offer the products services or features discussed in this document in other countries Consult your local IBM representative for information on the products and services currently available in your area Any reference to an IBM product program or service is not intended to state or imply that only that IBM product program or service may be used Any functionally equivalent product program or service that does not infringe any IBM intellectual property right may be used instead However it is the user s responsibility to evaluate and verify the operation of any non IBM product program or service IBM may have patents or pending patent applications covering subject matter described in this document
6. Switch Modules for IBM BladeCenter support entry level to enterprise SAN I O requirements for next generation data centers The Brocade switch modules include the following hardware features Six external auto sensing Fibre Channel ports 2 Gbps 4 Gbps or 8 Gbps for 8Gb SFP transceivers that operate at a maximum speed of 8 Gbps e 14 internal Fibre Channel ports that operate as F_ports fabric ports at 2 Gbps 4 Gbps or 8 Gbps depending on FC expansion cards installed into blades e 10 port model includes 10 Dynamic Ports On Demand DPODs that can be activated in any combination of internal and external ports e High availability features including hot pluggable design non disruptive software upgrades automatic path failover and power on self test diagnostics and status reporting e Aggregate Fibre Channel I O bandwidth 48 Gbps 6 external ports at 8 Gbps line rate e External ports that can operate as F_ports fabric ports FL_ports fabric loop ports or E_ports expansion ports when in full FC switch mode When in Brocade Access Gateway mode the external ports operate as NPIV enabled N_ Ports e Fabric latency of 0 74 usec ensures the fastest response and access time to data for critical applications and servers e Supports full 8 Gbps operations at distances up to 129 km and up to 1036 km at 1 Gbps Brocade Enterprise 20 port 20 port and 10 port 8Gb SAN Switch Modules 3 Brocade switch modules include the following s
7. al Controller 7 1727 Optional IBM System Storage EXP3000 Single or Dual ESM 39R6536 DS3000 Partition Expansion License Partition DS3000 Partition Expansion License License This configuration also requires cabling between the chassis and the storage server and between the storage server and expansion units The cable part numbers are not listed in the table Brocade Enterprise 20 port 20 port and 10 port 8Gb SAN Switch Modules 7 Installation in BladeCenter H high speed switch bays Figure 3 shows the Brocade 8Gb SAN Switch Modules installed in MSIMs in the BladeCenter H chassis The chassis is connected to the IBM System Storage DS3400 The servers in the chassis each have compatible CFFh Fibre Channel expansion cards The RAID functionality is provided by the external storage system sad mw E o a ae IBM System Storage IBM BladeCenter server IBM BladeCenter H chassis Figure 3 IBM BladeCenter H connected to an external IBM System Storage DS3400 storage solution Table 6 lists the parts that are used in this configuration Table 6 Components used as shown in Figure 3 Diagram Part number Description Quantity reference machine type IBM BladeCenter HS22 HS21 or other supported server Varies Supported CFFh expansion card see Table 4 1 per server 8852 IBM BladeCenter H chassis 39Y9314 Multi switch Interconnect Module 44X1920 Brocade 20 port 8Gb SAN Switch Module for IBM BladeCenter Not shown 44X1962 B
8. em Status This amber LED is at the top right of the I O module on the front panel This LED indicates that the I O module I O module has a fault If the I O module fails the POST this fault LED is lit External port There are six green external port activity TX RX LEDs When one of these LEDs flashes it status indicates that data is being received or transmitted that is activity is occurring on that port The TX RX flash frequency is proportional to the amount of traffic on that port External port There are six amber external port fault LEDs When an external port fault LED is lit it indicates diagnostics that the external port has failed the internal external or online port diagnostics tests Operating environment The environment has the following temperature and altitude requirements e Operating e 10 52 C 50 125 F at an altitude of 0 to 914 m 0 to 3 000 ft e 10 49 C 50 20 F at an altitude of 0 to 3 000 m 0 to 10 000 ft e Non operating e 40 65 C 40 149 F at an altitude of 0 to 12 000 m 0 to 39 370 ft The environment has the following humidity level requirements e Operating 8 to 80 noncondensing e Non operating 5 to 80 noncondensing Related publications For more information see the following links e Brocade 20 port and 10 port 8Gb SAN Switch Module for IBM BladeCenter Installation and User Guide http www ibm com support docview wss uid psg 1 MIGR 5082
9. eves appropriate without incurring any obligation to you Information concerning non IBM products was obtained from the suppliers of those products their published announcements or other publicly available sources IBM has not tested those products and cannot confirm the accuracy of performance compatibility or any other claims related to non IBM products Questions on the capabilities of non IBM products should be addressed to the suppliers of those products This information contains examples of data and reports used in daily business operations To illustrate them as completely as possible the examples include the names of individuals companies brands and products All of these names are fictitious and any similarity to the names and addresses used by an actual business enterprise is entirely coincidental Any performance data contained herein was determined in a controlled environment Therefore the results obtained in other operating environments may vary significantly Some measurements may have been made on development level systems and there is no guarantee that these measurements will be the same on generally available systems Furthermore some measurement may have been estimated through extrapolation Actual results may vary Users of this document should verify the applicable data for their specific environment COPYRIGHT LICENSE This information contains sample application programs in source language which illustrate programming techn
10. iques on various operating platforms You may copy modify and distribute these sample programs in any form without payment to IBM for the purposes of developing using marketing or distributing application programs conforming to the application programming interface for the operating platform for which the sample programs are written These examples have not been thoroughly tested under all conditions IBM therefore cannot guarantee or imply reliability serviceability or function of these programs Copyright International Business Machines Corporation 2009 All rights reserved Note to U S Government Users Restricted Rights Use duplication or disclosure restricted by GSA ADP Schedule Contract with IBM Corp Brocade Enterprise 20 port 20 port and 10 port 8Gb SAN Switch Modules 11 This document was created or updated on October 26 2010 Send us your comments in one of the following ways e Use the online Contact us review form found at ibm com redbooks e Send your comments in an e mail to redbook us ibm com e Mail your comments to IBM Corporation International Technical Support Organization Dept HYTD Mail Station P099 2455 South Road Poughkeepsie NY 12601 5400 U S A This document is available online at http www ibm com redbooks abstracts tips0747 html Trademarks IBM the IBM logo and ibm com are trademarks or registered trademarks of International Business Machines Corporation in the United States other c
11. model 42C 1828 is a fully enabled switch with a complete set of licensed features that maximizes performance ensures availability and simplifies management for the most demanding applications and expanding virtualization environments The factory installed licenses include e ISL Trunking Consolidates ISLs into fault tolerant and load balanced trunks with bandwidth of up to 48 Gbps for greater performance and simplified management e Adaptive Networking Ensures high priority connections obtain the bandwidth necessary for optimum performance e Advanced Performance Monitoring Provides end to end visibility into fabric performance to maximize performance tuning and the utilization of fabric resources e Fabric Watch Monitors and creates alerts based on the health of switch and fabric elements e Extended Fabrics Extends Fibre Channel SANs beyond traditional distance limitations for replication and backup e Server Application Optimization Allows Virtual Machine Quality of Service QoS authentication and monitoring from adapter through SAN Brocade Enterprise 20 port 20 port and 10 port 8Gb SAN Switch Modules 4 The following optional software features are available for the 10 port and 20 port modules These features are factory installed on the Enterprise 20 port module 42C 1828 e 10 Port Port on Demand upgrade for 10 port model 32R1822 e ISL Trunking 26K5607 e Advanced Performance Monitoring 45W0508 e Extended Fabrics
12. oftware features e Brocade Full Fabric mode Enables high performance 8Gb fabric switching e Brocade Access Gateway mode Leverages NPIV to connect to any fabric without adding switch domains to reduce management complexity e Dynamic Path Selection Enables exchange based load balancing across multiple Inter Switch Links ISLs for superior performance e Brocade Advanced Zoning Segments a SAN into virtual private SANs to increase security and availability e Brocade Enhanced Group Management Enables centralized and simplified management of Brocade fabrics through IBM System Storage Data Center Fabric Manager DCFM Brocade switch modules support the following fabric management all management connections go through the management module e IBM System Storage DCFM Centralizes and simplifies management of enterprise level SAN fabrics consisting of IBM System Storage b type using FOS and Brocade fabrics m type using M EOS SAN products e IBM System Storage DCFM Professional Plus For customers managing single fabrics up to 1000 ports running Brocade Fabric OS FOS products e Brocade Web Tools Provides Web based management interface designed to help simplify monitoring and configuration management e Command line interface CLI through the Telnet program e Switch SNMP agent which enables receipt of configuration values traffic information and FC failure data through SNMP and the Ethernet interface The Enterprise 20 port
13. or IBM BladeCenter 32R1822 Not available Brocade 8Gb SFP SW Optical Transceiver 44X1962 5084 The switch module part numbers include the following items e Brocade Enterprise 20 port 20 port or 10 port 8Gb SAN Switch Module for IBM BladeCenter e Gasket for installation in a BladeCenter H Multi switch Interconnect Module MSIM e Documentation CD containing e Brocade 20 port and 10 port 8Gb SAN Switch Module for IBM BladeCenter Installation and User Guide e End User License Agreement EULA e Safety Information e Brocade documentation e The 6M Important Notices document The switch does not ship with small form factor pluggable plus SFP modules and they must be ordered separately Table 1 lists the transceiver that is supported Brocade Enterprise 20 port 20 port and 10 port 8Gb SAN Switch Modules 2 Switch comparison Brocade 8Gb SAN Switch Modules for IBM BladeCenter support entry level to enterprise SAN I O requirements for next generation data centers Table 2 provides a feature comparison by model Table 2 Feature comparison by model Feature Enterprise 20 port switch 10 port switch 20 is switch Number Number of active pots active Number of active pots Enhanced Group Management Included Included Included Features Brocade and IBM are delivering innovative and powerful IT infrastructure for virtual data centers based on best in class industry standard computing and networking technology Brocade 8Gb SAN
14. ountries or both These and other IBM trademarked terms may also be registered or common law trademarks in other countries A current list of IBM trademarks is available on the Web at http www ibm com legal copytrade shtml The following terms are trademarks of the International Business Machines Corporation in the United States other countries or both BladeCenter IBM Redbooks Redbooks logo System Storage System x Other company product or service names may be trademarks or service marks of others Brocade Enterprise 20 port 20 port and 10 port 8Gb SAN Switch Modules 12
15. rocade 8Gb SFP SW Optical Transceiver Up to 12 1726 42X IBM System Storage DS3400 Dual Controller 1727 Optional IBM System Storage EXP3000 Single or Dual ESM Not shown 39R6536 DS3000 Partition Expansion License This configuration also requires cabling between the chassis and the storage server and between the storage server and expansion units The cable part numbers are not listed in the table Brocade Enterprise 20 port 20 port and 10 port 8Gb SAN Switch Modules 8 Connectors and LEDs The front panel of the Brocade 8Gb SAN Switch Module contains the following components as shown in Figure 4 e Information LEDs that display the status of the I O module and its network connections e Six external Fibre Channel ports to connect Fibre Channel devices and switches These ports are labeled 0 15 16 17 18 and 19 from top to bottom on the I O module System status LEDs aaa Port 0 LEDs 115 LEDs t 16 LEDS Fort 17 LEDs Port 18 4 eo poo Por 18 LEDs 119 LEDs Y Media access control MAC address label Figure 4 Front panel of the Brocade 8Gb SAN Switch Module Brocade Enterprise 20 port 20 port and 10 port 8Gb SAN Switch Modules Table 7 lists the LEDs on the front panel and their meanings Table 7 LEDs on the front panel LED description System Status This green LED is at the top left of the I O module on the front panel and indicates that the module OK is working properly Syst
16. talled in a BladeCenter HT unit the internal ports operate up to 2 Gbps and the external ports operate at speeds up to 8 Gbps A E oa Brocade Enterprise 20 port 20 port and 10 port 8Gb SAN Switch Modules 6 Popular configurations The Brocade 8Gb SAN Switch Modules can be used in various configurations Installation in standard switch bays Figure 2 shows the Brocade 8Gb SAN Switch Modules that are installed in standard I O bays in the BladeCenter chassis The chassis is connected to the IBM System Storage DS3400 The servers in the chassis each have compatible CFFv or ClOv Fibre Channel expansion cards The Redundant Array of Independent Disks RAID functionality is provided by the external storage system IBM BladeCenter server m ox IBM BladeCenter piisas M EIL A El IBM System Storage Figure 2 IBM BladeCenter connected to an external IBM System Storage DS3400 storage solution Table 5 lists the parts that are used in this configuration Table 5 Components used as shown in Figure 2 Diagram Part number Description Quantity reference Machine type IBM BladeCenter HS22 HS21 or other supported server 2 Varies Supported ClOv or CFFv expansion card see Table 4 1 per server 44X1920 Brocade 20 port 8Gb SAN Switch Module for IBM BladeCenter 44X1962 Brocade Brocade 8Gb SFP SW Optical Transceiver SFP SW Brocade 8Gb SFP SW Optical Transceiver Transceiver Upto12 to Upto12 o 1726 42X IBM System Storage DS3400 Du
Download Pdf Manuals
Related Search