Technoline Temperature Station
Contents
1. Indoor sign NoooR Minimum INDOOR Maximum 57 By pressing the MIN MAX key the current indoor temperature will alternate between the minimum maximum and current temperature recordings also changes for outdoor temperature Once a new indoor temperature high or low is reached it will automatically set into the Temperature Station s memory OUTDOOR TEMPERATURE READING The outdoor temperature reading is on the bottom line of the LCD under the indoor temperature The Temperature Station receives the outdoor temperature via 433 MHz frequency when the batteries are inserted into the transmitter within the 2 1 2 minutes of the setting up time See Setting up above 58 Note Should the outdoor temperature not be received within 2 1 2 minutes after inserting the batteries into a transmitter then see Checking 433 MHz reception below 59 MINIMUM AND MAXIMUM OUTDOOR TEMPERATURE READING OUTDOOR icon m lt 5 60 By pressing the MIN MAX key the current indoor and outdoor temperature will alternate between the minimum maximum and current temperature recordings The time when the minimum and maximum outdoor temperature records were received will be also shown on the LCD blinking recorded time is for outdoor temperature only Once a new outdoor temperature high or is low reached it will automatically be set into2. SET CH key once more to enter the Celsius or Fahrenheit degree setting mode 53 CELSIUS OR FAHRENHEIT DEGREE SETTING Following from the 12 or 24 hour setting mode 1 or F will appear the LCD If C is displayed then the current temperature reading is set to Celsius If F is displayed then the current temperature reading is set to Fahrenheit 2 alternate between the two temperature reading modes simply press the MIN MAX key 3 Press SET CH key to confirm and enter the time setting mode TIME SETTING Following from the Celsius or Fahrenheit degree mode 54 The Hour digit in the time section starts flashing Using the MIN MAX key enter the hours of the current time and then followed by pressing the SET CH key to advance to the minute mode Again using the MIN MAX key enter the minutes of the current time by holding the key down the digits are incremented in steps of five and then finally followed by pressing the SET CH key to exit the setting mode Your Temperature Station is now fully operational 55 USING THE TEMPERATURE STATION INDOOR TEMPERATURE The indoor temperature is displayed on the second line of the LCD under the time The Temperature Station s built in sensor automatically measures the temperature once the batteries are inserted 56 MINIMUM AND MAXIMUM INDOOR TEMPERATURE RECORDINGS 4 lt 1
3. surface is in the immediate proximity garage doors double glazing etc Before 69 securing in place please ensure that the Temperature Station can receive the 433 MHz signal from the Outdoor Transmitter at the positions that you wish to situate them CARE AND MAINTENANCE e Avoid placing the units in areas prone to vibration and shock as these may cause damage e Avoid areas where the units can be exposed to sudden changes temperature i e direct sunlight extreme cold and wet moist conditions as these will lead to rapid changes in temperature which reduces the accuracy of readings 70 When cleaning the LCD and casing use a soft damp cloth only Do not use solvents or scouring agents Do not submerge the units into water Immediately remove all low powered batteries to avoid leakage and damage Replace only with new batteries of the recommended size Do not make any repairs to the units Please return them to the original point of purchase for repair by a qualified engineer Opening and tampering with the units may invalidate its guarantee 71 SPECIFICATIONS Temperature measuring range Indoor 0 C to 60 with 0 1 resolution 32 F to 140 F with 0 2 F resolution displayed if outside this range Outdoor 29 9 to 69 9 with 0 1 resolution 21 8 to 157 2 F with 0 2 F resolution displayed if outside this range 72 Temperature checking intervals Indoor tempe
4. 433 MHZ TEMPERATURE STATION Instruction Manual INTRODUCTION Congratulations on purchasing this innovative 433MHz Temperature Station which displays the time with up to the minute indoor and up to three outdoor temperature readings To enjoy the full benefits of this innovative product please read this operating manual 42 TEMPERATURE STATION Hanging hole Battery compartment SET CH key mia key Detachable 43 stand TEMPERATURE TRANSMITTER Holder 44 FEATURES LCD clock in 12 or 24 hour time display Indoor and outdoor temperature reading in degrees Celsius or Fahrenheit Can receive up to three Outdoor transmitters Indoor and outdoor temperature with Minimum and Maximum records and time received for outdoor only Table standing or wall mountable detachable table stand 45 BATTERIES REPLACEMENT amp MAINTENANCE For best performance batteries to all units should be replaced at least once a year to maintain optimum running accuracy Ensure that the batteries used are new of the correct size Please help in the preservation of the environment and return used batteries to an authorized depot 46 SETTING UP Please follow these steps to ensure that your new Temperature Station works correctly with the temperature transmitter s an BF Battery compartment Battery 59 4 compartment Battery cover Battery cover 47 Flip open the
5. battery cover at the back of the Temperature Station as indicated above Checking the correct polarization insert 2 x AAA IEC LR3 1 5V batteries into the battery compartment and replace the cover all the segments of the LCD screen will light up momentarily Now slide the battery cover open on the transmitter as indicated above Checking the correct polarization insert 2 x AA IEC LR6 1 5V batteries into the battery compartment and replace the cover If you have purchased additional outdoor transmitter s wait until the outdoor temperature has been received from the one 48 transmitter before activating the next transmitter by repeating steps 3and4 However ensure that you leave 10 seconds in between the reception of the last transmitter and the set up of the following transmitter The Temperature Station will number the transmitters in the order of set up i e the first transmitter will have the temperature displayed with the number 1 against it and so on When the outdoor temperature s is received the Temperature Station and transmitter s should be positioned in the desired places see Positioning amp securing below 49 Note Should the total time of inserting the batteries into the transmitters take longer than 2 1 2 minutes from the time of inserting the batteries into the Temperature Station then temperature reception problems may occur If the temperature is not be received then see Checking for 433 MHz reception bef
6. chable stand that gives the option of table standing or wall mounting To wall mount 1 Fix screw into the desired wall leaving the head extended out the by about 5mm 2 Using the Temperature Station s hanging gt hole carefully hang it onto the screw 2 Note Always that the unit locks onto the screw head before releasing 2 67 OUTDOOR TRANSMITTER The Outdoor Transmitter is supplied with a holder that may be attached to a wall with the three screws or double sided tape supplied To attach to the wall using screws please follow the steps below 1 Mark the using through the holes 2 2 in the holder to obtain the exact drilling 2 position 2 Drill holes in the wall at the points marked Screw holder onto wall 68 The Outdoor Transmitter simply clicks in or out of the holder When inserting or removing the Outdoor Transmitter to or from the wall holder please hold both units securely to avoid tearing the holder from the wall There is also double sided tape included with the wall holder On smooth surfaces this can be used instead of drilling holes The mounting surface can however affect the transmission range If for example the unit is attached to a piece of metal it may then either reduce or increase the transmitting range For this reason we recommend not placing the unit on any metal surfaces or in any position where a large metal or highly polished
7. doors window frames or structures Using other electrical products such as headphones and speakers that operate on the same signal 433 MHz can prevent the transmission pick up Neighbours using electrical products operating on the 433 MHz signal can also cause interference In most severe cases the 64 reception is only possible once all other electrical products using the 433 MHz are switched off Within thick concrete rooms such as basements and tower blocks the 433 MHz signal can be weakened avoid placing near metal frames and structures Transmission can be affected by exposure to extreme temperature conditions For example if the weather has been extremely cold under 25 C for an extended period of time then the transmission signal may be weakened Please bears this in mind when positioning the transmitter 65 Note Should after checking the above list and the outdoor temperature is still not received then reset the units see Resetting the Temperature Station below RESETTING THE TEMPERATURE STATION 1 Remove the batteries from the Temperature Station and the transmitter s 2 Wait at least 30 seconds and repeat the procedures specified in Setting up above Note Remember when resetting all units have to be reset and to always insert the batteries into the Remote Thremo first and then followed by the transmitter s 66 POSITIONING TEMPERATURE STATION The Temperature Station comes complete with a deta
8. or any incorrect readings and any consequences that occur should an inaccurate reading take place This product is designed for use in the home only as indication of the temperature This product is not to be used for medical purposes or for public information 76 The specifications of this product may change without prior notice This product is not a toy Keep out of the reach of children No part of this manual may be reproduced without written authorization of the manufacturer 77 R amp TTE Directive 1999 5 EC Summary of the Declaration of Conformity We hereby declare that this wireless transmission device does comply with the essential requirements of R amp TTE Directive 1999 5 EC 78
9. ore resetting the units see Resetting the Temperature Station below In the event of changing batteries in any of the units all units need to be reset by following the setting up procedures This is because a random security code is assigned by the transmitter at start up and this code must 50 be received and stored by the Temperature Station in the first 2 1 2 minutes of power being supplied to it LCD SCREEN The Temperature Station s LCD is comprised of three lines and once the batteries are inserted all the segments will light up momentarily before displaying 1 Time 2 Indoor and outdoor temperature in degree Celsius C or Fahrenheit F 51 Time Indoor Temperature in C or F Outdoor Temperature in C or F Transmitter identification number TIME 110 INDOOR OUTDOOR Im 52 Outdoor Transmission signal 12 or 24 hour setting After the batteries are inserted set the time display as follow 1 2 Press hold the key about 3 seconds to enter the set mode Either a 12h or 24h will appear on the LCD If 12h is displayed then the current time display is set to 12 hour time If 24h is displayed then the current time is set to 24 hour time To alternate between the two times display mode simply press the MIN MAX key When the desired time display is selected press the
10. rature every 10 seconds Temperature Station Outdoor Temperature reception twice 10 minutes Transmitter minute Transmitting frequency 433 92 MHz Temperature transmitting range up to 25 meters Open space and free from interference Power source Temperature Station a 2 x AAA IEC LR3 1 5V batteries Transmitter 2 x AA IEC LR6 1 5V batteries 73 Battery life for both units Dimensions L x W x H Temperature Station Transmitter Approximately 12 months Alkaline batteries recommended 58 x 23 x 125 mm 39 x 21 x 128 mm 74 LIABILITY DISCLAIMER The electrical and electronic wastes contain hazardous substances Disposal of electronic waste in wild country and or in unauthorized grounds strongly damages the environment Please contact your local or and regional authorities to retrieve the addresses of legal dumping grounds with selective collection All electronic instruments must from now on be recycled User shall take an active part in the reuse recycling and recovery of the electrical and electronic waste The unrestricted disposal of electronic waste may do harm on public health and the quality of environment 75 As stated on the gift box and labeled on the product reading the User manual is highly recommended for the benefit of the user This product must however not be thrown in general rubbish collection points The manufacturer and supplier cannot accept any responsibility f
11. the Temperature Station s memory 61 RESETTING THE MINIMUM AND MAXIMUM TEMPERATURE RECORDING By pressing and holding down the MIN MAX key for about 3 seconds both the indoor and outdoor minimum and maximum temperature recordings will be reset to the current indoor and outdoor temperatures Only the outdoor temperature channel being displayed on the LCD will be reset To reset another outdoor temperature channel user shall first move to the desired transmitter No OUTDOOR TEMPERATURE 1 2 AND 3 If the more than one transmitter is being used to alternate between the 62 temperature readings of transmitter 1 2 and 3 simply press the SET CH key If the reading is from transmitter 1 then the identification numbers 1 will be displayed in the outdoor temperature section of the LCD The same will apply to the next transmitter and so on However if only one transmitter is used no identification number will be displayed on the LCD CHECKING FOR 433 MHz RECEPTION In normal surroundings for example away from interfering sources such as TV sets the outdoor temperature can usually be easily received within 2 1 2 minutes If the outdoor temperature is not displayed on the LCD after 2 1 2 minutes then check the following 63 The distance of the units should be at least 1 5 2 0 meters away from interfering sources such as computer monitors or TV sets Avoid placing the units onto or in the immediate proximity of metal
Download Pdf Manuals
Related Search