CRU DE100, Carrier Only, 68-pin, U160
Contents
1. of the ID select cable to the 1 25mm connector J3B provided on the signal distribution board located inside the carrier Refer to the manufactur er s documentation to disable termination on the drive Typical Drive 16 Bit Wide Single Ended ID Select Pins Signal Pins vary on each drive model See Drive _ Distribution Manufacturer s Manual a L Board Se N Signal Row Data Express ID f Select Interface Inside Carrer Bro ack 9 a abe ow v A anga V W ted Cot J 16 Bit Wide LBD pong ID Select Cable GND Row ID Select Cable 2mm from Data Express ID Select Connector Drive Carrier Figure 4 Typical SCSI ID Select Connections 2mm Drive Pins gt 1 800 260 9800 Rugged Reliable Mobile Secure Selecting the Unit ID Number Use the alignment tool provided to select the ID number of the disk drive Unit ID Number Display a JA Lock and IDSeled DC power SJ J Front of Unit Drive Carrier uide Receiving rame Drive Carrier Removed Figure 5 Unit ID Select Switch Location NOTE The lock on the Data Express receiving frame functions as a lock and a DC power switch for the carrier unit The lock MUST be engaged turned coun terclockwise in order to supply power to the carrier and installed drive unit Limited Product Warranty CRU DataPort CRU warrants the Data Express DE100 to be free of significant de fects in mater2. Rugged Reliable Mobile Secure DE100 Ultra 160 68 pin Install Guide Removable SCSI Wide Ultra160 Drive Enclosure Cable Cover a Provided Disk Drive Not Included Power Cable _ I O Cable W2 Jumper Factory Installed Do Not Remove ID Select Cable 68 Pin 1 O Connector J2 DC Power Connector J3 Option Pin Connector 6 32 Phillips W1 Flat Hd Screw 6 Total Receiving Frame J4 Jumpers Factory Installed on Pins 7 amp 8 and Pins 9 amp 10 Remote iat r 1e Pod Figure 1 Drive Installation Assembly a ps 5 P ee FARI O OBN O nanto Receiving Frame Motherboard a a0 Factory Installed Jumpers J4 There are two 2 jumpers factory in stalled on J4 One jumper is located on Pins 7 amp 8 the other on Pins 9 amp 10 sing 4190 Reserved NOTE Do not remove jumpers Remove only if attaching the 6103 1020 0000 Isolator Board Ground Row Option Pin Connector W1 a Remote Unit ID Selection Pins 1 8 are provided for remote unit ID selec Figure 2 Drive Installation Assembly tion for the computer system or expansion chassis Remote ID selection requires that the unit ID select switch located inside the receiving frame be set to 0 Note he DE100 Ultra 160 may be shipped with an Isolator repeater board factory installed If this is the case your DE100 Ultra 160 will Remote Activity LED Pi
3. ial and workmanship for a period of five years from the original date of purchase CRU s warranty is nontransferable and is limited to the original purchaser Limitation of Liability The warranties set forth in this agreement replace all other warranties CRU expressly disclaims all other warranties including but not limited to the implied warranties of merchantability and fitness for a particular purpose and non infringement of third party rights with respect to the documentation and hardware No CRU dealer agent or em ployee is authorized to make any modification extension or addition to this warranty In no event will CRU or its suppliers be liable for any costs of procurement of substitute products or services lost profits loss of information or data computer malfunction or any other special indirect consequential or incidental damages arising in any way out of the sale of use of or inability to use any CRU product or service even if CRU has been advised of the possibility of such damages In no case shall CRU s liability exceed the actual money paid for the products at issue CRU reserves the right to make modi fications and additions to this product without notice or taking on additional liability Certification EMI Standard FCC Part 15 Class B CE EMC Standard EN55022 EN55024 FCC Certification This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC r
4. ns 9 amp 10 provide power for a remote LED device look slightly different from figure above Please refer to figure below activity indicator for receiving frame with isolator repeater board attached rear view Enable Termination Power Connector W2 A jumper is installed at the The DE100 Ultra 160 Isolator Repeater Board is an upgrade attach factory and enables termination power to from the SCSI bus ment for the DE100 Ultra 160 receiving frame This attachment pro vides both an enhanced bus isolating hot swap and repeater function NOTE Do not remove this jumper gt 1 800 260 9800 gt www CRU DataPort com 6103 1020 0000 Isolator Board Detail Mounting Hole Mounting Hole DX1 200 SW160 RH Isolator Board DE100 or DE200 Ultra160 Only Receiving Frame Motherboard Figure 3 Receiving Frame Motherboard rear view Typical 2MM Drive ID Pin Configuration Figure below illustrates a typical SCSI ID select connection to a drive with 2mm ID select pins The wires on the wire harness connect to the positive pin or signal pins on the disk drive In some cases the drive manufacturer will label the signal pins as Pin 1 3 5 7 instead of 0 1 2 3 as shown in figure below Also in some cases the even numbered Pins 2 4 6 are used for Ground Attach the ID select cable to the drive using the 2mm connectors Align the IDO pin with the black wire Attach the 1 25mm connector on the other end
5. ules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Register your product at www CRU DataPort com A7 100 0008 Rev 1 1 gt www CRU DataPort com
Download Pdf Manuals
Related Search