Profoon PDX 240
Contents
1. 1 2 3 4 Press 0K key Press A or V key to select SETUP BS and press 0K key Press A or V key to select CHANGE PIN and press 0K key the LCD will show ENTER PIN Press number key to input the old PIN code and press 0K key the LCD will show NEW PIN prompt you to input a new PIN code Note Wrong PIN will be shown if the old PIN code you input is wrong and then return to step 4 5 6 Input the desired new PIN code and press 6 OK key the LCD will show REPEAT PIN prompt you to input the new PIN code again Input the new PIN code again and press OK key to confirm the setting Note 1 The PIN code must be 4 digits 2 If the new PIN code that you input two times is different the change will fail the display will return to step 5 26 Ring Melody You may select one of the 5 available base ringer tones for your incoming calls alert tone Press OK key 1 Press A or V key to select SETUP BS and press 6 0K key 2 Press A or V key to select RING MELODY and press 0K key 3 Press A or key to select the desired ring melody the selected melody will be sounded 4 Press OK key to confirm the setting Ring Volume You may select one of the 5 available volumes for your incoming calls alert tone The default setting is volume 5 Ringer can be disable by pressing C key for 1 5 seconds in idle mode 1 Press 6 0K key 2 P2. VOL key voL Caller ID Down Decrease v volume key 9 0K Menu OK key C 6 l Z Mute Cancel Ring off key R Flash key ag Phone book key C Talk Off key INT Asterisk INT key Hon Hash Keypad lock key Pause Pause Key Paging LCD Display of lt oc PNY A A ait 1 a 5 Description Aerial icon Phone icon Speaker phone in use icon Key lock icon No ring icon BRIJA Microphone mute icon z Intercom call indicator Battery level indicator Phonebook icon Menu icon Voice mail waiting indicator VMWI icon Caller ID icon PR BE Alarm icon Basic Operation Make a Call 1 2 Press the C key wait for a dial tone then dial the desired number After finishing the conversation press C key or place the cordless handset into the charger The talk timer will be shown for about 2 seconds before return to idle mode Pre dialling 1 2 4 When the handset is in idle mode input the desired number Press C key to cancel the wrong digit input the correct one again If a pause is needed during dialing press and hold Pause key for a while and character P will be shown A 3 seconds pause will be added while dialing Press the C key the number will be automatically dialled out After finishing the conversation press C key or place the cordless handset
3. To delete a digit before the cursor press C key After editing take telephone line with the handset the number will be automatically dialed out Save Call Record Py 3 When the handset is in idle mode press rgi key Press A or V key to select the desired record Press 0K key to enter menu Press A or V key to select SAVE NUMBER press 0K key the selected number will be shown press 0K key ENTER NAME will be shown and input the desired name You must input the name otherwise the record can t be saved Press OK key to save Delete a Single Call Record 1 When the handset is in idle mode press ree key 2 Press A or V key to select the desired record 3 Press OK key to enter menu 4 Press A or V key to select DELETE press 0K key CONFIRM will be shown 5 Press 0K key to confirm Delete All Call Record 1 When the handset is in idle mode press rg key 2 Press A or V key to select the desired ae 3 Press OK key to enter menu press A or V key to select DELETE ALL press 0K key CONFIRM will be shown 4 Press 0K key to confirm 18 Phone Book The telephone can store up to 25 entries in the phone book with name and call number When the function is supported by the telephone provider service and the caller the handset displays the name of the caller when stored in the phone book Store Entries 1 Press AA key to a
4. as this can cause static discharge Periodically clean the charge contacts on the handset base and charger with a soft cloth Troubleshooting Guide PROBLEMS CAUSES SOLUTIONS Registration The battery is not Charge the battery for not work sufficiently 14 hours see Battery charged Charging Handset and base Unplug and then plug station were not in the power adapter prepare for registration No display The battery has not Charge the battery or been charged replace them see Battery Charging No reactions The keypad is to keystroke locked Press on key longer than 2 seconds No radio connection to The handset is Move closer to the the base outside the base base station 342 station T blinking station range The handset is not registered The base station does not work Register the handset see Registering Handset Unplug and then plug the power adapter to the power outlet 220 230V AC 50 Hz and the other end into the power jack on base bottom 35
5. default setting is Off 1 2 3 Press 0K key Press A or W key to select SETUP HS and press 0K key Press A or V key to select TONES and press 0K key Press A or V key to select NO COVERAGE and press 0K key Press A or V key to select ON or OFF Press 0K key to confirm the setting 2 Key Tone You may set the key tone to On or Off when you press the keypad The default setting is On 1 Press 0K key 2 Press A or V key to select SETUP HS and press 0K key 3 Press A or V key to select TONES and press 0K key 4 Press A or V key to select KEY TONE and press 0K key 5 Press A or V key to select ON or OFF 6 Press O0K key to confirm the setting Auto Talk This option allows user to pick up the cordless handset from charger to answer the call directly when a call is coming and no need press C key The default setting is On 1 2 3 Press 0K key Press A or V key to select SETUP HS and press 0K key Press A or V key to select AUTO TALK and press 0K key Press A or V key to select ON or OFF Press 0K key to confirm the setting 23 Alarm Press 0K key Press A or V key to select SETUP HS and press 0K key Press A or V key to select ALARM and press 0K key Press A or Y key to select ON or OFF Enter
6. to one base 1 Press 6 OK key 2 Press A or V key to select REGISTRATION and press OK key 3 Press A or V key to select REGISTER and press 0K key Press A or V key to select a base and press 0K key the LCD will display ENTER PIN 4 Input the correct PIN code and press 0K key to begin to register the cordless handset the LCD will display SEARCHING 5 Press and hold the page key The base will beep twice and the red light will flash for one minute Note 1 SUCCESSFUL will be shown on handset LCD display if the handset is registered to the base Cordless handset number will be shown after it returns to idle mode 2 NO BASE will be shown on handset LCD display if the cordless handset is not registered to the base within 1 minute register the handset again 3 WRONG PIN will be shown on handset LCD display if the PIN code you input is wrong The register fails 31 Select Base This option allows user to select a base 1 Press 0K key 2 Press A or V key to select REGISTRATION and press 0K key 3 Press A or V key to select SEL BASE and press 0K key Press A or V key to select a specific base or Auto 4 press OK key to comfirm the setting Remove Handset This option allows user to remove the registered cordless handset from the base 5 Press 0K key 6 Press A or V key to select REGISTRATION and press 0K key 7 Pr
7. HH MM in 24 hour format Press 0K key to confirm Note When Alarm time is reached ALARM ON will blinking and alarm sound will stop after around 1 minute Handset Name You can set the cordless handset name that you like The default setting is Handset 1 Press 0K key 2 Press A or V key to select SETUP HS and press 0K key 3 Press A or V key to select NAME and press 0K key 4 Edit the desired name using number key Press 0K key to confirm the setting Nn 24 Language Sixteen different languages are available for selection for each handset 1 Press 0K key 2 Press A or V key to select SETUP HS and press 0K key 3 Press A or V key to select LANGUAGE and press 0K key 4 Press A or V key to select Language 5 Press 0K key to confirm the setting Reset Handset This option allows user to restore the cordless handset to the default setting 1 2 S Press 0K key Press A or V key to select SETUP HS and press 0K key Press A or V key to select RESET and press 0K key the LCD will display RESET Press 0K key to confirm the setting 25 Base Setting Change PIN PIN is your base s identification number the function is to avoid the setting is changed by others The default setting is 0000 You may change the PIN Please take down the change so as to operate the unit normally
8. User Manual PDX 200 Please observe the following to ensure reliable operation of the telephone Read this manual thoroughly and observe the operating instructions and information provided Place the base station on a non slip surface and lay the connection cables so they cannot be the source of an accident Do not expose the equipment to extreme temperatures or high relative humidity and protect it from direct sunlight and dusty conditions Clean the equipment with a soft damp cloth Do not use any solvents or aggressive cleaning agents Only connect approved accessories Only use the power plug supplied Never open the unit Opening the unit annuls claims under the terms of guarantee and exposes the person to the risk of an electric shock Repairs to defective units should only be carried out by service centers recommended by the sales outlet We recommend removing the batteries if the equipment is not to be used for longer periods Only replace the batteries with types recommended by us Dispose of defective batteries according to the applicable local laws not in household waste We assume no liability for damage caused by using the equipment for unintended purposes Exemption from Liability We cannot guarantee the information which relates to the technical properties or that contained in this document is correct The product and its accessories described in this document are subject to constant improvement and f
9. ccess phone book memory 2 Press 0K key to access phone book menu 3 Press A or V key to select ADD NEW and press 0K key 4 Enter number max 24 digits and press 0K key when finished 5 Enter name max 12 characters and press 0K key when finished Note 1 When the capacity is full MEMORY FULL will display 2 Any incorrect input can be deleted by pressing C key Edit Entries Press Aa key to access phone book memory 1 Press A or V key to scroll 2 Press 0K key to select a desired entry and then press A or to select the submenu EDIT 3 Press OK to start Number edition and press 0K key again to start Name edition 4 Press 0K key to confirm Note Press C key to delete any incorrect input 19 Delete Entries Press An key to access phone book memory 1 Press A or key to scroll 2 Press OK key to select a desired entry and then press A or Y to select the submenu DELETE 3 Press OK key to delete the entry 4 Press OK key again to confirm Delete All Entries Press aa key to access phone book memory 1 Press A or V key to scroll 2 Press 0K key to select a desired entry and then press A or Y to select the submenu DELETE ALL 3 Press 0K key to delete the entry 4 Press OK key again to confirm 20 Menu Operation Handset Setting Ring Melody You may select one of the 10 available ringer tones for your incoming calls alert tone T
10. ess A or V key to select REMOVE HANDSET and press 0K key the LCD will display ENTER PIN 8 Input the correct PIN code and press 0K key 9 Press A or V key to select the cordless handset you want to remove and press 0K key the LCD will display REMOVE HANDSET 10 Press 0K key to confirm the setting Note 1 The removed handset LCD will show NOT REG You must register it again before using it 2 If the PIN code you input is wrong WRONG PIN will be shown on cordless handset LCD 33 Technical Specifications Handset Operating Approx 10 hours talk time Time average Approx 100 hours standby values AC DC Adapter VD060025D For Base Unit Input 230V AC 50 Hz Output 6VDC 250mA VD060015D For Charger Input 230V AC 50 Hz Output 6 VDC 150 mA Single phase AC excluding IT installations defined by the EN 60950 standard Caution the network voltage is classified as a hazard by the criteria of this standard Telephone connection Appliance designed for connection to an analogue telephone line class TNV3 telecommunications network voltage as defined by the EN 60950 standard Rechargeable Battery GP45AAAHC 1 2V 450mAh Ni MH AAA x 2 or equivalent For guidance only depends on initial battery charge 33 General Product Care Simply wipe the base station with a damp cloth or an antistatic wipe Never use a dry cloth
11. et is in idle mode press and hold INT key INT Number will be shown input the called handset number The called handset will ring and the LCD will show the calling handset s name and number Press C key in the called handset to answer Call Transfer The function allows you to transfer an external call from a handset to another handset 1 With the caller on line press and hold INT key on the calling unit and input the called unit number The line will put on hold and the caller will hear hold music After the called unit answers the call the intercom will begin between the calling unit and called unit If you want to transfer the call to the called unit only need to end the call at the calling unit The call will be automatically transferred to the called unit During intercom mode if you want to return to talk to the caller press OK key on the handset to enter menu then press A or V key to select Switching press 0K key on the handset to confirm The intercom call will be put on hold If you want to restore the intercom call please repeat step 4 Note 1 If the called unit doesn t answer the intercom call within 1 40 the calling unit will return to the talk 2 mode with the caller 2 Only the calling unit can operate the SWITCHING function 3 You can only make an intercom call during call timer is displayed 4 After power is failure you answered a call the intercom f
12. handset is in idle mode press Por key Press A or key to select the desired redial number Press 0K key to enter menu press A or V key to select DELETE ALL press 0K key CONFIRM will be shown lt fse 4 Press 0K key to confirm Note During redial function operating If you want to return to the upper layer menu press C key Ifyou want to return to idle mode directly press C key on the handset Caller ID Service The caller s information will be displayed and recorded if you have subscribed to Caller ID service from your local telephone company When the telephone rings the caller s information will be displayed on the handset LCD display This information includes the phone number and name if supported The handset can store up 20 calls for later review up to 20 digits and 12 characters for each record When the memory is full a new call automatically replaces the oldest call in the memory Note If the caller s information includes Date Time the Date Time will be stored with the record The Date Time displayed on the LCD display will be updated after receiving a call If the caller number is same as one of phonebook memory the matched name stored in the phonebook memory will be displayed If the incoming call is registered as PRIVATE NUMBER and its caller ID information is withheld the LCD will show WITHHELD If the incoming call does not have Caller ID service or its
13. he default setting is Melody 1 1 2 3 4 5 Press 0K key Press A or V key to select SETUP HS and press 0K key Press A or V key to select RING MELODY and press 0K key Press A or V key to select the desired ring melody the selected melody will be sounded Press 0K key to confirm the setting Ring Volume You may select one of the 5 available volumes for your incoming calls alert tone The default setting is volume 5 Ringer can be disable by pressing C key for 1 5 seconds in idle mode 1 2 3 Press 0K_key Press A or V key to select SETUP HS and press 0K key Press A or V key to select RING VOLUME and press 0K key Press A or key to select the desired ring volume the selected volume will be sounded Press 0K key to confirm the setting 2 i TONES Low Battery You may set the warning beep to On when your cordless handset battery is low so as to alert you to charge the battery The default setting is On 1 2 3 Press 0K key Press A or V key to select SETUP HS and press 0K key Press A or V key to select TONES and press 0K key Press A or V key to select LOW BATTERY and press 0OK key Press A or V key to select ON or OFF Press OK key to confirm the setting No Coverage You may set the warning beep to On or Off when the cordless handset is out of range The
14. into the charger The talk timer will be shown for about 2 seconds before return to idle mode Adjust the Receiver Volume While the phone is in talk mode press A or V key on the handset to adjust the receiver volume of the handset There are 5 possible volume selections for handset receiver The display will show the current volume level during adjusting 10 Answer a Call When the phone rings the icon C will flash and the LCD on the handset will show Call If you have subscribed to Caller ID service from your local telephone company the incoming call information will be shown 1 Press the C key to answer a call 2 After finishing the conversation press C key or place the cordless handset into the charger Auto Answer If you set on the Auto talk just need to pick up the cordless handset from the charger to answer the call directly needn t press C key Dialing from the Phone Book Press nA button when in standby mode the first entry in the phone book appears Note If there is no record in phone book PB EMPTY information will display 1 Press A or V key to select the required record from the phone book 2 Press C key to dial the number 3 After finishing the conversation press C key or place the cordless handset into the charger to terminate the call Intercom You can make an intercom any two handsets if you have more than one handset 1 3 When the hands
15. ompromised Warning The handset does not work and damaged if the wrong batteries are inserted If batteries are empty handset LCD will not has any display and the handset will not response to any key Handset is then required to put back on Base Station Charger cradle to charge Handset cannot be used until handset name and aerial icon appear If handset does not charged full before use handset may emit battery low alert tone and battery level indicator shows empty 4 Feature List Comfortable digital cordless phone with DECT Standards 25Name and number phone book Caller ID and Caller ID with Call Waiting Incoming 20 name number call log Multi language menu 10 Ringtone melodies Ringer on off 10 Last number redial 5 level ring volume Real time clock display Handset naming Automatic call answering Key input tone on off Keypad lock Teleconference Internal free communication between handsets Battery status inc low battery warning Up to 100 hours standby Up to 10 hours continuous talk time Out of range warning Recall Pause Hold Tone and pulse dialling More than one handset require Subscription may be required Please contact your network provider DECT Digitally Enhanced Cordless Telephone Standard for Cordless telephones Handset and Base Layouts A Redial Up Increase volume
16. onfirm the setting Reset Base This option allows user to restore the base and Date Time to the default setting 1 2 3 Press 0K key Press A or V key to select SETUP BS and press 0K key Press A or V key to select RESET and press 0K key the LCD will display ENTER PIN Input the correct PIN code using number key press 0K key to confirm and the LCD will display RESET Press 0K key to confirm the setting 29 DATE TIME You can set the Date Time displayed in idle mode The default setting is 2008 01 01 12 01 1 2 3 a 6 Press 0K key Press A or V key to select DATE TIME and press 0K key the LCD will display YEAR 2008 Input the correct last two digits of year range 00 99 using number key press OK key to confirm the setting and enter month and date setting Input the correct month and date the format is month date month range 01 12 date range 01 30 31 using number key press 0K key to confirm the setting and enter time setting Input the correct time the format is hour minute hour range 00 23 minute range 00 59 using number key Press 0K key to confirm the setting Note If the value you input is over the range during setting you can t enter next setting by pressing OK key please enter the correct setting again 30 Registration Up to 4 cordless handsets can be registered
17. op the page call Short press any key on the handset or press page key briefly on the base Switching the Key Lock On Off Press and hold Ho key to activate or deactivate the key lock The OFF icon turns on or off Redial Function The last 10 numbers you dialed out will be separately stored in handset redial memory Review and Dial Redial Record 1 When the handset is in idle mode press VoL key to display the last redial record If the redial record is empty EMPTY will be shown 14 2 3 Press A or key to select the desired redial number Press C key the telephone number is automatically dialed out Save Redial Number 4 When the handset is in idle mode press YoL key Press A or key to select the desired redial number Press 0K key to enter menu press A or V key to select SAVE NUMBER press 0K key on the handset the selected number will be shown press OK key ENTER NAME will be shown and input the desired name You must input the name otherwise the record can t be saved Press OK key to save Delete a Single Redial Record 1 2 3 4 When the cordless handset is in idle mode press Pkt key Press A or key to select the desired redial number Press 0K key to enter menu press A or V key to select DELETE press 0K key CONFIRM will be shown Press OK key to confirm Delete All Redial Records When the
18. ress A or V key to select SETUP BS and press 6 0K key 3 Press A or V key to select RING VOLUME and press OK key 4 Press A or V key to select the desired ring volume the selected volume will be sounded 5 Press 6 0K key to confirm the setting 07 Dial Mode You may set the dial mode to Tone or Pulse according to your needs The default setting is Tone 1 2 3 4 X Press 0K_key Press A or V key to select SETUP BS and press 0K key Press A or V key to select DIAL MODE and press 0K key Press A or V key to select TONE or PULSE Press 0K key to confirm the setting Recall Time You may select flash time from 100ms to 800ms according to your needs The default setting is 100ms 1 2 3 Press 0K key Press A or V key to select SETUP BS and press 0K key Press A or V key to select RECALL TIME and press 0K key Press A or key to select the desired flash time Press 0K key to confirm the setting 28 VMWI If you have subscribed to a voice messaging service the VMWI LED on the base will flash to alert you if you have a messages waiting To turn Visual Message Waiting Indication VMWI off 1 Press OK key 2 Press A or V key to select SETUP BS and press 0K key 3 Press A or V key to select VMWI and press 0K key VMWI OFF will display 4 Press 0K key to c
19. service area is not linked to yours the LCD will show UNAVAILABLE 16 The handset will prompt user if there is unanswered call 9 When the handset is in idle mode R gt will be displayed prior to other display information If you reviewed all the missed calls from handset the display 2 R will be disappeared Note 1 If you reviewed all the missed calls from one handset Fd the display handsets 2 Press key to toggle the display between name and number Review Caller ID Record 1 When the handset is in idle mode press r key to display the information for the last call received 2 Press A or WV key to review all call records 3 When you scroll to the end GO BACK will be shown Note 1 The ag icon will turn on if the call is a missed call 2 EMPTY will be displayed for 2 seconds and return to idle mode if you have not received any call 3 If one handset is in reviewing caller ID mode the others handset can t do the same operation at the same time Impossible will be shown on the LCD Edit and Dial Call Record You can edit the call record so as to dial back 2 m 1 When the handset is in idle mode press vr key 2 Press A or V key to select the desired record 3 Press 0K key to enter menu will be disappeared from other 217 Press A or WV key to select Select press 0K key To insert a digit using the keypad at a desired location
20. unction is disable if power is restored during talking Three way Conversation You may have a 3 way conversation using the intercom and an open line 1 With the caller on line press INT key on the calling unit and input the called unit number The line will put on hold and the caller will hear hold music After the called unit answers the call the intercom will begin between the calling unit and called unit Press OK key on the handset to enter menu then press A or V key to select Conference press 0K key on the handset to confirm The three way conference will begin among the calling unit the called unit and the caller If you want to end the three way conference and return to the intercom press OK key on the handset to enter menu then press A or V key to select Single call press OK key on the handset to confirm If you want to return to the conference mode please repeat step 3 Note Only the calling unit can operate the Conference or Single call function 13 Muting the Ringer volume Press and hold C amp key in idle mode to activate or deactivate the handset Ringer The amp icon turns on or off Muting the Microphone Press C amp key can switch the microphone on or off during a call The B icon turns on or off Paging the Handset If a handset has been misplaced it is possible to call all the handsets Short press Page key on the base to station To st
21. urther development For this reason we reserve the right to modify components accessories technical specifications and related documentation of the product described herein without notification Intended Use This telephone is designed for telephoning within a telephone network Any other use is considered unintended use Unauthorized modifications or reconstruction not described in this manual are not permitted Connecting the Base Station and Power Plug Connecting the plugs to the corresponding sockets in the base station they can not be connected incorrectly because the sockets and plugs are designed prevent reverse poling Lay the cable under the telephone to the rear Plug the telephone line in the telephone connection socket Insert the power plug at the other end in the power outlet The base station is now ready to operate Only use the connection cable supplied AC power outlet Phone jack CAUTION Plug the adapter to the socket outlet that near the equipment and shall be easily accessible Use only the power supply that came with this unit Using other power supplies may damage the unit Getting Started Install and Charge the Batteries Insert two pieces AAA batteries in the compartment ensuring correct polarity and close the compartment Place the handset in the base station to charge for 16 hours prior for first use If you don t properly charge the phone battery performance will be c
Download Pdf Manuals
Related Search