Intel Celeron M 380
Contents
1. APIC related erratum This item is either new or modified from the previous version of the document Each Specification Update item is prefixed with a capital letter to distinguish the product The key below details the letters that are used in Intel s microprocessor Specification Updates A Intel 8 Pentium II processor B Mobile Intel 8 Pentium 8 II processor C Intel 8 Celeron processor E Intel 8 Pentium 8 III processor F Intel Pentium processor Extreme Edition and Intel Pentium D processor G Intel 8 Pentium III Xeon processor H Mobile Intel 8 Celeron 8 processor at 466 433 400 366 333 300 and 266 MHz J 64 bit Intel Xeon processor MP with 1MB L2 Cache K Mobile Intel 8 Pentium III processor Specification Update L Intel Celeron 8 D processor M Mobile Intel 8 Celeron 8 processor N Intel 8 Pentium 4 processor O Intel 8 Xeon processor MP P Intel Xeon processor Q Mobile Intel Pentium 4 processor supporting Hyper Threading Technology on 90 nm process technology R Intel Pentium 4 processor on 90 nm process S 64 bit Intel Xeon processor with 800 MHz system bus 1 MB and 2 MB L2 cache versions T Mobile Intel Pentium 4 processor M V Mobile Intel Celeron processor on 13 Micron Process in Micro FCPGA Package W Intel Celeron M processor X Intel Pentium M processor on 90nm process with 2 MB L2 Cache Y Intel Pentium2. Memory Type of the Load Lock Different from its Corresponding Store V40 X X X NoFix Unlock A 16 bit Address Wrap Resulting from a Near Branch Jump or Call V41 X X X NoFix May Cause an Incorrect Address to Be Reported to the GP Exception Handler Incorrect Debug Exception DB May Occur When a Data Breakpoint v42 X Xx X NoFix is seton an FP Instruction V43 X X X NoFix xAPIC May Not Report Some Illegal Vector Errors Memory Aliasing of Pages as Uncacheable Memory Type and Write a X x X Nomix Back WB May Hang the System A Timing Maginality in the Arithmetic Logic Unit ALU May Cause uae A PANEI Indeterminate Behavior With TF Trap Flag Asserted FP Instruction That Triggers an V46 X X X No Fix Unmasked FP Exception May Take Single Step Trap Before Retirement of Instruction BTS Branch Trace Store and PEBS Precise Event Based Sampling a x x A No Fix May Update Memory outside the BTS PEBS Buffer Memory Ordering Failure May Occur with Snoop Filtering Third Party V48 X X X No Fix Agents after Issuing and Completing a BWIL Bus Write Invalidate Line or BLW Bus Locked Write Transaction Control Register 2 CR2 Can be Updated during a REP MOVS STOS V49 X X X No Fix Instruction with Fast Strings Enabled A Writing the Local Vector Table LVT when an Interrupt is Pending May V50 X x X No Fix Cause an Unexpected Interrupt Number SPECIFICATION CHANGE V1 Cont
3. The Mobile Intel Celeron processor may contain design defects or errors known as errata which may cause the product to deviate from published specifications Current characterized errata are available on reguest tHyper Threading Technology requires a computer system with a Mobile Intel Pentium 4 Processor a chipset and BIOS that utilize this technology and an operating system that includes optimizations for this technology Performance will vary depending on the specific hardware and software you use See http www intel com info hyperthreading for information Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order Intel Pentium Celeron Intel Xeon Intel SpeedStep Intel NetBurst and the Intel logo are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries Other names and brands may be claimed as the property of others Copyright Intel Corporation 2002 2005 All rights reserved 2 Specification Update intel Contents Revision AISTORY iicaiieo dk aa kalaliik vaada a a aaas aad aaa ke kalk tahta a 4 Ne ienaa fess VS E cava taala lad 1M Aa paali a jadana taa UU Ataka ATi 6 Summary Of CHANGES isere aii vahad k va teda mm havai and vad TaN 8 Identification INTOrMAatiOn AA AMMAS 12 Erata sinikas TT 15 Specification Clarifications wnenrnnnaeananneenneenann
4. The time stamp counter as implemented in the P6 family Pentium Pentium M Pentium 4 and Intel Xeon processors is a 64 bit counter that is set to 0 following a RESET of the processor Following a Specification Update Note RESET the counter will increment even when the processor is halted by the HLT instruction or the external STPCLK pin Note that the assertion of the external DPSLP pin may cause the time stamp counter to stop Members of the processor families increment the time stamp counter differently e For Pentium M processors family 06H models 09H ODH for Pentium 4 processors Intel Xeon processors family OFH models 00H 01H or 02H and for P6 family processors the time stamp counter increments with every internal processor clock cycle The internal processor clock cycle is determined by the current core clock to bus clock ratio Intel SpeedStep technology transitions may also impact the processor clock e For Pentium 4 processors Intel Xeon processors family OFH models 03H and higher the time stamp counter increments at a constant rate That rate may be set by the maximum core clock to bus clock ratio of the processor or may be set by the frequency at which the processor is booted The specific processor configuration determines the behavior Constant TSC behavior ensures that the duration of each clock tick is uniform and supports the use of the TSC as a wall clock timer even if the processor co
5. V31 Problem Implication Workaround Status 26 intel Erroneous BIST Result Found in EAX Register after Reset The processor may show an erroneous BIST built in self test result in the EAX register bit 0 after reset When this erratum occurs an erroneous BIST failure will be reported in the EAX register bit 0 however this failure can be ignored since it is not accurate It is possible for BIOS to workaround this issue by masking off bit 0 in the EAX register where BIST results are written For the steppings affected see the Summary Tables of Changes Processor Does Not Flag GP on Non Zero Write to Certain MSRs When a non zero write occurs to the upper 32 bits of I432 CR SYSENTER EIP or IA32 CR SYSENTER ESP the processor should indicate a general protection fault by flagging GP Due to this erratum the processor does not flag GP The processor unexpectedly does not flag GP on a non zero write to the upper 32 bits of IA32_CR_SYSENTER_EIP or IA32_CR_SYSENTER_ESP No known commercially available operating system has been identified to be affected by this erratum None identified For the steppings affected see the Summary Tables of Changes Simultaneous Assertion of A20M and INIT May Result in Incorrect Data Fetch If A20Mf and INIT are simultaneously asserted by software followed by a data access to the OxFFFFFXXX memory region with A20M still asserted incorrect data will be accessed With AZOM
6. intel Table 1 Mobile Intel Celeron Processor Identification Information L2 S Spec Kased oy Si ka Core Freguency ari cy Voltage Package Notes bytes SL6FM_ BO 256 K OF 24h 1 4 GHz 400 MHz 1 3V Micro FCPGA SL6FN BO 256 K OF 24h 1 5 GHz 400 MHz 1 3 V Micro FCPGA SL6M4 C1 256 K OF27h 1 4 GHz 400 MHz 1 3V Micro FCPGA SL6M5 C1 256 K OF27h 1 5 GHz 400 MHz 1 3V Micro FCPGA SL6J2 C1 256 K OF27h 1 6 GHz 400 MHz 1 3V Micro FCPGA SL6J3 C1 256 K OF27h 1 7 GHz 400 MHz 1 3V Micro FCPGA SL6J4 C1 256 K OF27h 1 8 GHz 400 MHz 1 3V Micro FCPGA SL6QH C1 256 K OF27h 2 0 GHz 400 MHz 1 3 V Micro FCPGA SL6ZW C1 256 K OF27h 2 2 GHz 400 MHz 1 3V Micro FCPGA SL7MG D1 256K OF29h 1 2 GHz 400 MHz 1 3V Micro FCPGA SL6VG D1 256 K OF29h 1 70 GHz 400 MHz 1 3V Micro FCPGA SL6VH D1 256 K OF29h 1 80 GHz 400 MHz 1 3V Micro FCPGA SL6VJ D1 256 K OF29h 2 00 GHz 400 MHz 1 3V Micro FCPGA SL73Y D1 256 K OF29h 2 20 GHz 400 MHz 1 3V Micro FCPGA SL75J D1 256 K OF29h 2 40 GHz 400 MHz 1 3V Micro FCPGA NOTES 1 Based on BO Shrink process 2 Supported by the Embedded Intel Architecture Division Specification Update 13 Component Marking Information Figure 1 Mobile Intel Celeron Processor on 13 Micron Process Micro FCPGA Markings FFFFFFFF S N PRODUCT DETAIL maa S SPEC COO S INTEL mc 01 14 Specification Update intel Errata V1 Problem Implication W
7. M processor Z Mobile Intel Pentium 4 processor with 533 MHz system bus AC Intel Celeron Processor in 478 Pin Package The Specification Updates for the Pentium processor Pentium Pro processor and other Intel products do not use this convention Steppings NO Plans ERRATA BO C1 D1 Vi x x x NoFix UO restart in SMM may fail after simultaneous machine check exception MCE A MCA registers may contain invalid information if RESET occurs and v2 a x A Noki PWRGOOD is not held asserted V3 X X X NoFix Transaction is not retried after BINIT V4 X X X NoFix Invalid opcode OFFFh requires a ModRM byte v5 x x x NoFix FSW may not be completely restored after page fault on FRSTOR or FLDENV instructions The Processor Signals Page Fault Exception PF Instead of V6 X X X NoFix Alignment Check Exception AC on an Unlocked CMPXCHG8B Instruction V7 x x x NoFix When in no fill mode the memory type of large pages are incorrectly forced to uncacheable vS x x xX NoFix Processor may hang due to speculative page walks to non existent system memory va x x x NoFix The IA32_MC1_STATUS register may contain incorrect information for correctable errors V10 X X X NoFix Debug mechanisms may not function as expected V11 x x x NoFix Machine check architecture error reporting and recovery may not work as expected V12 X x x NoFix Cascading of performance counters does not work correctly when forced over
8. asserted an access to OXFFFFFXXX should result in a load from physical address OXFFEFFXXX However in the case of A20M and INIT being asserted together the data load will actually be from the physical address OXFFFFFXXX Code accesses are not affected by this erratum Processor may fetch incorrect data resulting in BIOS failure Deasserting and reasserting A20M prior to the data access will workaround this erratum For the steppings affected see the Summary Tables of Changes Processor Does Not Respond to Break Requests from ITP On power up and low power state transitions the processor s TAP circuitry may remain in the Tap Logic Reset TLR state The ITP is unable to cause a break on reset in the processor which may prevent the loading of processor and chipset registers or affect the ability to debug from cold boot and low power transitions None identified For the steppings affected see the Summary Tables of Changes Specification Update intel Problem Implication Workaround Status V33 Problem Implication Workaround Status V34 Problem Implication Workaround Status CPUID Instruction Returns Incorrect Number of ITLB Entries When CPUID is executed with EAX 2 it should return a value of 51h in EAX 15 8 to indicate that the Instruction Translation Lookaside Buffer ITLB has 128 entries Due to this erratum the processor returns 50h 64 entries Software may incorre
9. under certain bus and memory timing conditions the system may loop in a continual seguence of UC fetch implicit writeback and Reguest For Ownership RFO retries This erratum has not been observed in any commercially available operating system or application The aliasing of memory regions a condition necessary for this erratum to occur is documented as being unsupported in the JA 32 Intel Architecture Software Developer s Manual Volume 3 section 10 12 4 Programming the PAT However if this erratum occurs the system may hang The pages should not be mapped as either UC or WC and WB at the same time For the steppings affected see the Summary Tables of Changes A Timing Marginality in the Arithmetic Logic Unit ALU May Cause Indeterminate Behavior A timing marginality may exist in the clocking of the ALU which leads to a slowdown in the speed of the circuit s operation This could lead to incorrect behavior of the ALU When this erratum occurs unpredictable application behavior and or system hang may occur It is possible for the BIOS to contain a workaround for this erratum For the steppings affected see the Summary Tables of Changes With TF Trap Flag Asserted FP Instruction That Triggers an Unmasked FP Exception May Take Single Step Trap Before Retirement of Instruction an FP instruction generates an unmasked exception with the EFLAGS TF 1 it is possible for external events to occur including a transition to a lo
10. 4Gbyte boundaries Alternately ensure that the page fault handler restarts program execution at the faulting instruction after correcting the paging problem For the steppings affected see the Summary Tables of Changes Specification Update intel V6 Problem Implication Workaround Status V7 Problem Implication Workaround Status V8 Problem Implication Workaround Status The Processor Signals Page Fault Exception PF Instead of Alignment Check Exception AC on an Unlocked CMPXCHG8B Instruction If a Page Fault Exception PF and Alignment Check Exception AC both occur for an unlocked CMPXCHG8B instruction then PF will be flagged Software that depends on the Alignment Check Exception AC before the Page Fault Exception PF will be affected since PF is signaled in this case Remove the software s dependency on AC having precedence over PF Alternately correct the page fault in the page fault handler and then restart the faulting instruction For the steppings affected see the Summary Tables of Changes When in No Fill Mode the Memory Type of Large Pages are Incorrectly Forced to Uncacheable When the processor is operating in No Fill Mode CRO CD 1 the paging hardware incorrectly forces the memory type of large PSE 4M and PAE 2M pages to uncacheable UC memory type regardless of the MTRR settings By forcing the memory type of these pages to UC load operations w
11. Nominal CPI Time stamp counter ticks instructions retired measures the CPI over the duration of a program including those periods when the machine halts while waiting for I O 15 10 9 3 Incrementing the Time Stamp Counter 36 The time stamp counter increments when the clock signal on the system bus is active and when the sleep pin is not asserted The counter value can be read with the RDTSC instruction The time stamp counter and the non sleep clockticks count may not agree in all cases and for all processors See Section 10 8 for more information on counter operation Specification Update IN tal Specification Changes V1 The Specification Changes listed in this section apply to the following documents e Mobile Intel Celeron Processor on 13 Micron Process in Micro FCPGA Package Datasheet Document Number 251308 All Specification Changes will be incorporated into a future version of the appropriate mobile Intel Celeron processor on 0 13 micron process in Micro FCPGA package documentation Context ID Feature Added to the CPUID Instruction Feature Flags IA32_MISC_Enable Registers TA32 MISC ENABLE register bit 24 status has changed from Reserved to the following definition IA32 MISC ENABLE Miscellaneous Enables Register bit 24 MSR Address 01A0h Accessed as a Qword Default Value High Dword XXXX XXXXh Low Dword XXXX XXXX XXXX XXXX XXXX XX00 X0X0 0001b Access Read Write Type Shared IA32 MIS
12. This only impacts JTAG TAP accesses to the processor Other bus accesses are not affected To minimize the effects of this issue reduce noise on the TCK net at the processor relative to ground and position TCK relative to BCLK to minimize the TAP error rate Decreasing rise times to under 800ps reduced the failure rate but does not stop all failures For the steppings affected see the Summary Tables of Changes The State of the Resume Flag RF Flag in a Task State Segment TSS May be Incorrect After executing a JMP instruction to the next or other task through a hardware task switch it is possible for the state of the RF flag in the EFLAGS register image to be incorrect The RF flag is normally used for code breakpoint management during debug of an application It is not typically used during normal program execution Code breakpoints or single step debug behavior in the presence of hardware task switches therefore may be unpredictable as a result of this erratum This erratum has not been observed in commercially available software None For the steppings affected see the Summary Tables of Changes Specification Update intel V38 Problem Implication Workaround Status V39 Problem Implication Workaround Status V40 Problem Implication Workaround Status Changes to CR3 Register do not Fence Pending Instruction Page Walks When software writes to the CR3 register it is
13. are three ways to count processor clock cycles to monitor performance These are e Non halted clockticks Measures clock cycles in which the specified logical processor is not halted and is not in any power saving state When Hyper Threading Technology is enabled this these ticks can be measured on a per logical processor basis e Non sleep clockticks Measures clock cycles in which the specified physical processor is not in a sleep mode or in a power saving state These ticks cannot be measured on a logical processor basis e Time stamp counter Some processor models permit clock cycles to be measured when the physical processor is not in deep sleep by using the time stamp counter and the RDTSC instruction Note that such ticks cannot be measured on a per logical processor basis See Section 10 8 for detail on processor capabilities The first two methods use performance counters and can be set up to cause an interrupt upon overflow for sampling They may also be useful where it is easier for a tool to read a performance counter than to use a time stamp counter the timestamp counter is accessed using the RDTSC instruction For applications with a significant amount of I O there are two ratios of interest e Non halted CPI Non halted clockticks instructions retired measures the CPI for phases where the CPU was being used This ratio can be measured on a logical processor basis when Hyper Threading Technology is enabled e
14. if any further errors occur the MCA overflow bit will not be updated thereby incorrectly indicating only one error has been received If an I O instruction IN INS REP INS OUT OUTS or REP OUTS is being executed and if the data for this instruction becomes corrupted the processor will signal a Machine Check Exception MCE If the instruction is directed at a device that is powered down the processor may also receive an assertion of SMI Since MCEs have higher priority the processor will call the MCE handler and the SMI assertion will remain pending However while attempting to execute the first instruction of the MCE handler the SMI will be recognized and the processor will attempt to execute the SMM handler If the SMM handler is successfully completed it will attempt to restart the I O instruction but will not have the correct machine state due to the call to the MCE handler This can lead to failure of the restart and shutdown of the processor If PWRGOOD is de asserted during a RESET assertion causing internal glitches the MCA registers Specification Update 19 Implication Workaround Status V12 Problem Implication Workaround Status 20 ntel may latch invalid information If RESET is asserted then de asserted and reasserted before the processor has cleared the MCA registers then the information in the MCA registers may not be reliable regardless of the state or state transitions of PW
15. of Changes Memory Ordering Failure May Occur with Snoop Filtering Third Party Agents after Issuing and Completing a BWIL Bus Write Invalidate Line or BLW Bus Locked Write Transaction Under limited circumstances the processors may after issuing and completing a BWIL or BLW transaction retain data from the addressed cache line in shared state even though the specification requires complete invalidation This data retention may also occur when a BWIL transaction s self snooping yields HITM snoop results A system may suffer memory ordering failures if its central agent incorporates coherence sequencing which depends on full self invalidation of the cache line associated with 1 BWIL and BLW transactions or 2 all HITM snoop results without regard to the transaction type and snoop results source 1 The central agent can issue a bus cycle that causes a cache line to be invalidated Bus Read Invalidate Line BRIL or BWIL transaction in response to a processor generated BWIL or BLW transaction to insure complete invalidation of the associated cache line If there are no intervening processor originated transactions to that cache line the central agent s invalidating snoop will get a clean snoop result Or 2 Snoop filtering central agents can a Not use processor originated BWIL or BLW transactions to update their snoop filter information or b Update the associated cache line state information to shared state on the o
16. stale data Ignore any information in the T432 MCU ADDR and I432 MC0 MISC registers after a data address or response parity error For the steppings affected see the Summary Tables of Changes CR2 May Be Incorrect or an Incorrect Page Fault Error Code May Be Pushed onto Stack After Execution of an LSS Instruction Under certain timing conditions the internal load of the selector portion of the LSS instruction may complete with potentially incorrect speculative data before the load of the offset portion of the address completes The incorrect data is corrected before the completion of the LSS instruction but the value of CR2 and the error code pushed on the stack are reflective of the speculative state Intel has not observed this erratum with commercially available software When this erratum occurs the contents of CR2 may be off by two or an incorrect page fault error code may be pushed onto the stack It is possible for the BIOS to contain a workaround for this erratum For the steppings affected see the Summary Tables of Changes Specification Update 23 V23 Problem Implication Workaround Status V24 Problem Implication Workaround Status V25 Problem Implication Workaround Status 24 intel BPM 5 3 and GHI VIL Does Not Meet Specification The Vy for BPM 5 3 and GHI is specified as 0 9 GTLREF V Due to this erratum the Vy for these signals is 0 9 GTLREF
17. 075 V The processor requires a lower input voltage than specified to recognize a low voltage on the BPM 5 3 and GHI signals When intending to drive the BPM 5 3 or GHI signals low ensure that the system provides a voltage lower than 0 9 GTLREF 075 V For the steppings affected see the Summary Tables of Changes Processor May Hang Under Certain Frequencies and 12 5 STPCLK Duty Cycle If a system de asserts STPCLK at a 12 5 duty cycle the processor is running below 2 GHz and the processor thermal control circuit TCC on demand clock modulation is active the processor may hang This erratum does not occur under the automatic mode of the TCC When this erratum occurs the processor will hang If use of the on demand mode of the processor s TCC is desired in conjunction with STPCLK modulation then assure that STPCLK is not asserted at a 12 5 duty cycle For the steppings affected see the Summary Tables of Changes System May Hang If a Fatal Cache Error Causes Bus Write Line BWL Transaction to Occur to the Same Cache Line Address as an Outstanding Bus Read Line BRL or Bus Read Invalidate Line BRIL A processor internal cache fatal data ECC error may cause the processor to issue a BWL transaction to the same cache line address as an outstanding BRL or BRIL As it is not typical behavior for a single processor to have a BWL and a BRL BRIL concurrently outstanding to the same address this may represent an une
18. 1 cache parity error occurs the cache controller logic should write the physical address of the data memory location that produced that error into the 432 MC1 ADDR REGISTER MC1 ADDR In some instances of a parity error on a load operation that hits the L1 cache the cache controller logic may write the physical address from a subseguent load or store operation into the IA32 MC1 ADDR register When an error exists in the tag field of a cache line such that a request for ownership RFO issued by the processor hits multiple tag fields in the L2 cache the correct tag and the tag with the error and the accessed data also has a correctable error the processor will correctly log the multiple tag match error but will hang when attempting to execute the machine check exception handler Ifa memory access receives a machine check error on both 64 byte halves of a 128 byte L2 cache sector the 1432 MCU STATUS register records this event as multiple errors i e the valid error bit and the overflow error bit are both set indicating that a machine check error occurred while the results of a previous error were in the error reporting bank The 1432 MC1 STATUS register should also record this event as multiple errors but instead records this event as only one correctable error The overflow bit should be set to indicate when more than one error has occurred The overflow bit being set indicates that more than one error has occurred Because of this erratum
19. C ENABLE is a 64 bit register accessed only when referenced as a Oword through a RDMSR or WRMSR instruction Bit 24 of the I432 MISC ENABLE status has changed from Reserved to the following Descriptions L1 Data Cache Context Mode R W When set to a 1 this bit places the L1 Data Cache into shared mode When set to a 0 default this bit places the L1 Data Cache into adaptive mode When this bit is set to a 0 adaptive mode the Page Directory Base Register contained in CR3 must be identical across all logical processors Note If the Context ID feature flag ECX 10 is not set to a 1 after executing the CPUID instruction with EAX 1 then this feature is not supported and BIOS must not alter the contents of this bit location In the CPUID instruction function feature information bit 10 of ECX register ECX 10 has been assigned flag to identify Context ID feature The status has changed from Reserved to the following ECX Bits Descriptions of Feature Flag Value Context ID A value of 1 indicates the L1 data cache mode can be set to either adaptive mode or shared mode A value of 0 indicates this feature is not supported See definition of the 432 MISC ENABLE MSR Bit 24 L1 Data Cache Context Mode for more details Specification Update 37 V2 38 intel The BRO maximum hold time has changed to 2 BCLKs This change will be shown in the System Bus AC Specifications Reset Condition
20. If the processor detects a page fault which is corrected before the operating system page fault handler can be called e g DMA activity modifies the page tables and the corrected page tables are left in a non accessed or not dirty state the processor may livelock Intel has not been able to reproduce this erratum with commercial software Should this erratum be encountered the processor will livelock resulting in a system hang or operating system failure It is possible for the BIOS to contain a workaround for this erratum For the steppings affected see the Summary Tables of Changes Incorrect Data May be Returned When Page Tables Are in Write Combining Memory WC Space If page directories and or page tables are located in Write Combining WC memory speculative loads to cacheable memory may complete with incorrect data Cacheable loads to memory mapped using page tables located in write combining memory may return incorrect data Intel has not been able to reproduce this erratum with commercially available software Do not place page directories and or page tables in WC memory For the steppings affected see the Summary Tables of Changes Processor Issues Inconsistent Transaction Size Attributes for Locked Operation When the processor is in the Page Address Extension PAE mode and detects the need to set the Access and or Dirty bits in the page directory or page table entries the processor sends an 8 byte load lock onto the sys
21. RGOOD If MCERR is asserted by one processor and observed by another processor the observing processor does not log the assertion of MCERR The Machine Check Exception MCE handler called upon assertion of MCERR will not have any way to determine the cause of the MCE The Overflow Error bit bit 62 in the 432 MCU STATUS register indicates when set that a machine check error occurred while the results of a previous error were still in the error reporting bank i e The Valid bit was set when the new error occurred If an uncorrectable error is logged in the error reporting bank and another error occurs the overflow bit will not be set The MCA Error Code field of the IA32_MCO_STATUS register gets written by a different mechanism than the rest of the register For uncorrectable errors the other fields in the 1432 MCU STATUS register are only updated by the first error Any further errors that are detected will update the MCA Error Code field without updating the rest of the register thereby leaving the 1432 MCO_STATUS register with stale information When a speculative load operation hits the L2 cache and receives a correctable error the TA32 MCI Status Register may be updated with incorrect information The 432 MC1 Status Register should not be updated for speculative loads The processor should only log the address for L1 parity errors in the 432 MC1 Status register if a valid address is available If a valid address is not a
22. V33 Added identification info for D 1 step 2 4 GHz June 2003 Updated summary table code Z Added Erratum V37 July 2003 Added V2 Specification Change Added Errata V38 August 2003 Added Errata V39 and V40 September 2003 Added Errata V41 October 2003 Updated Errata V41 November 2003 Updated Errata V42 March 2004 Updated Errata V6 April 2004 Updated Errata V11 Added Errata V43 May 2004 Added Errata V44 Updated Processor Identification Information June 2004 Added Errata V45 September 2004 Added Errata V46 47 October 2004 Added errata V48 November 2004 Added errata V49 December 2004 Added Specification Clarification V2 May 2005 4 Specification Update Updated Related Documents table July 2005 EN Added errata V50 and updated Processor Identification Table October 2005 Specification Update 5 Preface This document is an update to the specifications contained in the document listed in the following Affected Related Documents table It is a compilation of device and document errata and specification clarifications and changes and is intended for hardware system manufacturers and for software developers of applications operating system and tools Information types defined in the Nomenclature section of this document are consolidated into this update document and are no longer published in other documents This document may also contain information that has not been previously published Affected Documents Document Titl
23. When this erratum occurs the processor will hang The system BIOS should prevent the processor from going to the Deep Sleep state For the steppings affected see the Summary Tables of Changes When the Processor Is in the System Management Mode SMM Debug Registers May Be Fully Writeable When in System Management Mode SMM the processor executes code and stores data in the SMRAM space When the processor is in this mode and writes are made to DR6 and DR7 the processor should block writes to the reserved bit locations Due to this erratum the processor may not block these writes This may result in invalid data in the reserved bit locations Reserved bit locations within DR6 and DR7 may become invalid Software may perform a read modify write when writing to DR6 and DR7 to ensure that the values in the reserved bits are maintained For the steppings affected see the Summary Tables of Changes Specification Update intel V20 Problem Implication Workaround Status V21 Problem Implication Workaround Status V22 Problem Implication Workaround Status Associated Counting Logic Must Be Configured When Using Event Selection Control ESCR MSR ESCR MSRs allow software to select specific events to be counted with each ESCR usually associated with a pair of performance counters ESCRs may also be used to gualify the detection of at retirement events that support precise event based sa
24. ctly report the number of ITLB entries Operation of the processor is not affected None identified For the steppings affected see the Summary Tables of Changes A Write to APIC Registers Sometimes May Appear to Have Not Occurred In respect to the retirement of instructions stores to the uncacheable memory based APIC register space are handled in a non synchronized way For example if an instruction that masks the interrupt flag e g CLI is executed soon after an uncacheable write to the Task Priority Register TPR that lowers the APIC priority the interrupt masking operation may take effect before the actual priority has been lowered This may cause interrupts whose priority is lower than the initial TPR but higher than the final TPR to not be serviced until the interrupt flag is finally cleared 1 e by STI instruction Interrupts will remain pending and are not lost In this example the processor may allow interrupts to be accepted but may delay their service This non synchronization can be avoided by issuing an APIC register read after the APIC register write This will force the store to the APIC register before any subsequent instructions are executed No commercial operating system is known to be impacted by this erratum For the steppings affected see the Summary Tables of Changes Store to Load Data Forwarding may Result in Switched Data Bytes If in a short window after an instruction that updates a segment register has exe
25. cuted but not yet retired there is a load occurring to an address matches a recent previous store operation but the data size is smaller than the store the resulting data forwarded from the store to the load may have some of the lower bytes switched If this erratum occurs the processor may execute with incorrect data It is possible for the BIOS to contain a workaround for this erratum For the steppings affected see the Summary Tables of Changes Specification Update 27 V35 Problem Implication Workaround Status V36 Problem Implication Workaround Status V37 Problem Implication Workaround Status 28 intel Parity Error in the L1 Cache may Cause the Processor to Hang If a locked operation accesses a line in the L1 cache that has a parity error it is possible that the processor may hang while trying to evict the line If this erratum occurs it may result in a system hang Intel has not observed this erratum with any commercially available software None For the steppings affected see the Summary Tables of Changes The TCK Input in the Test Access Port TAP is Sensitive to Low Clock Edge Rates and Prone to Noise Coupling Onto TCK s Rising or Falling Edges TCK is susceptible to double clocking when low amplitude noise is riding on TCK edge while it is crossing the receiver s transition region TAP failures tend to increase with increases in background system noise
26. e Document Number Mobile InteP Celeron Processor on 13 Micron Process in Micro 251308 FCPGA Package Datasheet Related Documents Document Title Document Number 14 32 InteP Architecture Software Developer s Manual Volume 1 253665 Basic Architecture IA 32 Intel Architecture Software Developer s Manual Volume 253666 2A Instruction Set Reference A M IA 32 InteP Architecture Software Developer s Manual Volume 253667 2B Instruction Set Reference N Z 14 32 InteP Architecture Software Developer s Manual Volume 3 253668 System Programming Guide 6 Specification Update Nomenclature S Spec Number is a five digit code used to identify products Products are differentiated by their unigue characteristics e g core speed L2 cache size package type etc as described in the processor identification information table Care should be taken to read all notes associated with each S Spec number Errata are design defects or errors Errata may cause the mobile Intel Pentium 4 processor m s behavior to deviate from published specifications Hardware and software designed to be used with any given processor must assume that all errata documented for that processor are present on all devices unless otherwise noted Documentation Changes include typos errors or omissions from the current published specifications These changes will be incorporated in the next release of the specifications Specification Clarifications describe a
27. e microcode routine will trigger the data breakpoint resulting in a Debug Exception An incorrect Debug Exception DB may occur if data breakpoint is placed on an FP instruction Intel has not observed this erratum with any commercially available software or system None identified For the steppings affected see the Summary Tables of Changes xAPIC May Not Report Some Illegal Vector Errors The local xAPIC has an Error Status Register which records all errors The bit 6 the Receive Illegal Vector bit of this register is set when the local xAPIC detects an illegal vector in a received message When an illegal vector error is received on the same internal clock that the error status register is being written due to a previous error bit 6 does not get set and illegal vector errors are not flagged The xAPIC may not report some Illegal Vector errors when they occur at approximately the same time as other xAPIC errors The other xAPIC errors will continue to be reported None identified For the steppings affected see the Summary Tables of Changes Specification Update intel V44 Problem Implication Workaround Status V45 Problem Implication Workaround Status V46 Problem If Implication Workaround Status Memory Aliasing of Pages as Uncacheable Memory Type and Write Back WB May Hang the System When a page is being accessed as either Uncacheable UC or Write Combining WC and WB
28. e than half of the data bits within a 16 bit group would have been asserted electrically low the bus agent may invert the data bus signals for that particular sub phase for that 16 bit group Specification Clarification with Respect to Time stamp Counter In the Debugging and Performance Monitoring section Sections 15 8 15 10 9 and 15 10 9 3 of the IA 32 Intel Architecture Software Developer s Manual Volume 3 System Programming Guide the Time stamp Counter definition has been updated to include support for the future processors This change will be incorporated in the next revision of the IA 32 Intel Architecture Software Developer s Manual 15 8 Time Stamp Counter 34 The IA 32 architecture beginning with the Pentium processor defines a time stamp counter mechanism that can be used to monitor and identify the relative time occurrence of processor events The counter s architecture includes the following components e TSC flag A feature bit that indicates the availability of the time stamp counter The counter is available in an IA 32 processor implementation if the function CPUID 1 EDX TSC bit 4 1 e JA32_TIME_STAMP_COUNTER MSR called TSC MSR in P6 family and Pentium processors The MSR used as the counter e RDTSC instruction An instruction used to read the time stamp counter e TSD flag A control register flag is used to enable or disable the time stamp counter enabled if CR4 TSD bit 2 1
29. emory corruption None identified For the steppings affected see the Summary Tables of Changes Specification Update 29 V41 Problem Implication Workaround Status V42 Problem Implication Workaround Status V43 Problem Implication Workaround Status 30 intel A 16 bit Address Wrap Resulting from a Near Branch Jump or Call May Cause an Incorrect Address to Be Reported to the GP Exception Handler If a 16 bit application executes a branch instruction that causes an address wrap to a target address outside of the code segment the address of the branch instruction should be provided to the general protection exception handler It is possible that as a result of this erratum that the general protection handler may be called with the address of the branch target The 16 bit software environment which is affected by this erratum will see that the address reported by the exception handler points to the target of the branch rather than the address of the branch instruction None identified For the steppings affected see the Summary Tables of Changes FOPCODE Routine signals Debug Exception DB if a Data Breakpoint Is Set on an FP Instruction The default Microcode Floating Point Event Handler routine executes a series of loads to obtain data about the FP instruction that is causing the FP event If a data breakpoint is set on the instruction causing the FP event the load in th
30. ennanaanannnneanaanaanaanaanaaanana nan 34 Specification Change 14155414 24 vv isi nini naa Aled de dadada daa vaata J ee 37 Documentation Changes siirsin nanaii iania aiina 40 Specification Update 3 Revision History Revision Description Number Initial Release June 2002 Updated Identification Information table August 2002 003 Updated Documentation Change summary by removing old items that September 2002 have been incorporated into the Software Developer s Manual Added errata V30 V32 Added Documentation Changes V3 V24 004 Updated Summary of Changes Added prefix letter W Removed October 2002 previous errata V32 as not applicable added new errata V32 Added Documentation Changes V25 V32 005 Added errata V33 Added Spec Clarification V1 Added Spec Change V1 November 2002 Removed Documentation Changes that have been incorporated into the Software Developer s Manual Added a note in Documentation Changes No new Errata Documentation Change Spec Clarification or Spec December 2002 Change Updated note concerning the Software Developer s Manual Added Erratum V34 Updated summary tables to include C1 step January 2003 Added Erratum V35 February 2003 EI Updated Erratum V34 added new Erratum V36 March 2003 010 Updated codes used in summary tables Updated errata summary table April 2003 entry for V27 V28 V34 8 V36 Updated tables for D1 step Added info for C 1 step 1 6 GHz to 2 2 GHz to Table 1 May 2003 012 Updated Erratum
31. expected that all previous outstanding code data accesses and page walks are completed using the previous value in CR3 register Due to this erratum it is possible that a pending instruction page walk is still in progress resulting in an access to the PDE portion of the page table that may be directed to an incorrect memory address The results of the access to the PDE will not be consumed by the processor so the return of incorrect data is benign However the system may hang if the access to the PDE does not complete with data e g infinite number of retries It is possible for the BIOS to have a workaround for this erratum For the steppings affected see the Summary Tables of Changes System Bus Interrupt Messages without Data that Receive a HardFailure Response May Hang the Processor When a system bus agent processor or chipset issues an interrupt transaction without data onto the system bus and the transaction receives a HardFailure response a potential processor hang can occur The processor which generates an inter processor interrupt IPI that receives the HardFailure response will still log the MCA error event cause as HardFailure even if the APIC causes a hang Other processors which are true targets of the IPI will also hang on hardfail without data but will not record an MCA HardFailure event as the cause If a HardFailure response occurs on a system bus interrupt message with data the APIC will complete the operation
32. ext ID feature added to CPUID Feature IA32_MISC_Enable Registers V2 BRO Maximum Hold Time Specification Change Number SPECIFICATION CLARIFICATIONS Clarifying DBI Definition for all Processors with Intel NetBurst Microarchitecture Specification Clarification with respect to Time stamp Counter Number DOCUMENTATION CHANGES D There are no Documentation Changes in this Specification Update revision Specification Update 11 Identification Information 12 The mobile Intel Celeron processor on 13 micron process in Micro FCPGA package can be identified by the following values 1111 0010 00001000 1111 0010 00001111 NOTES 1 The Family corresponds to bits 11 8 of the EDX register after Reset bits 11 8 of the EAX register after the CPUID instruction is executed with a 1 in the EAX register and the generation field of the Device ID register accessible through Boundary Scan 2 The Model corresponds to bits 7 4 of the EDX register after Reset bits 7 4 of the EAX register after the CPUID instruction is executed with a 1 in the EAX register and the model field of the Device ID register accessible through Boundary Scan 3 The Brand ID corresponds to bits 7 0 of the EBX register after the CPUID instruction is executed with a 1 in the EAX register 4 This brand id MUST be used in conjunction with CPUID OF 24h 5 This brand id MUST be used in conjunction with CPUID OF27h Specification Update
33. flow is enabled V13 X X X NoFix EMON event counting of x87 loads may not work as expected V14 X X X NoFix Speculative page fault may cause livelock Specification Update 9 Steppings NO Plans ERRATA BO C1 D1 V15 x Fixed Incorrect data may be returned when page tables are in Write Combining WC memory space V16 x X X NoFix Processor issues inconsistent transaction size attributes for locked operation A Multiple accesses to the same S state L2 cache line and ECC error V17 X Fixed Aili A combination may result in loss of cache coherency V18 Fixed Processor may hang when resuming from Deep Sleep state v19 x x X NoFix When the processor isinthe System Management Mode SMM debug registers may be fully writeable A Associated counting logic must be configured when using Event v20 x X X Nomix Selection Control ESCR MSR IA32 MCO ADDR and IA32_MC0_MISC Registers Will Contain V21 X X x NoFix Invalid or Stale Data Following a Data Address or Response Parity Error V22 x Fixed CR2 May Be Incorrect or an Incorrect Page Fault Error Code May Be Pushed Onto Stack After Execution of an LSS Instruction V23 X Fixed BPM 5 3 and GHI Vi Do Not Meet Specification X X Processor May Hang Under Certain Frequencies and 12 5 Vea A MEE STPCLK Duty Cycle System May Hang if a Fatal Cache Error Causes Bus Write Line V25 X X X NoFix BWL Transaction t
34. hich should hit valid data in the L1 cache are forced to load the data from system memory Some applications will lose the performance advantage associated with the caching permitted by other memory types This erratum may result in some performance degradation when using no fill mode with large pages None identified For the steppings affected see the Summary Tables of Changes Processor May Hang Due to Speculative Page Walks to Non Existent System Memory A load operation that misses the Data Translation Lookaside Buffer DTLB will result in a page walk If the page walk loads the Page Directory Entry PDE from cacheable memory and that PDE load returns data that points to a valid Page Table Entry PTE in uncacheable memory the processor will access the address referenced by the PTE If the address referenced does not exist the processor will hang with no response from system memory Processor may hang due to speculative page walks to non existent system memory Page directories and page tables in UC memory space that are marked valid must point to physical addresses that will return a data response to the processor For the steppings affected see the Summary Tables of Changes Specification Update 17 v9 Problem Implication Workaround Status V10 Problem Implication Workaround Status 18 intel The IA32_MC1_STATUS Register May Contain Incorrect Information for Correctable Errors When a spec
35. line A is evicted from the WC Buffers to the bus queue which is still almost full 2 A hardware prefetch Read for Ownership RFO to cacheline B hits the S state in the L2 and observes cacheline A in the I state allocates both cachelines 3 An RFO to cacheline A completes before the WC Buffers write modified data back filling the L2 with stale data 4 The writeback from the WC Buffers completes leaving stale data for cacheline A in the Exclusive E state in the L2 cache Stale data may be consumed leading to unpredictable program execution Intel has not been able to reproduce this erratum with commercial software It is possible for BIOS to contain a workaround for this erratum For the steppings affected see the Summary Tables of Changes Re mapping the APIC Base Address to a Value Less Than or Equal to 0xDC001000 May Cause IO and Special Cycle Failure Remapping the APIC base address from its default can cause conflicts with either I O or special cycle bus transactions Either I O or special cycle bus transactions can be redirected to the APIC instead of appearing on the front side bus Use any APIC base addresses above 0xDC001000 as the relocation address For the steppings affected see the Summary Tables of Changes Specification Update 25 V28 Problem Implication Workaround Status V29 Problem Implication Workaround Status V30 Problem Implication Workaround Status
36. mpling PEBS A number of performance metrics that support PEBS reguire a 2nd ESCR to tag uops for the gualification of at retirement events The first ESCR is reguired to program the at retirement event Counting is enabled via counter configuration control registers CCCR while the event count is read from one of the associated counters When counting logic is configured for the subset of at retirement events that require a 2nd ESCR to tag uops at least one of the CCCRs in the same group of the 2nd ESCR must be enabled If no CCCR counter is enabled in a given group the ESCR in that group that is programmed for tagging uops will have no effect Hence a subset of performance metrics that require a 2nd ESCR for tagging uops may result in 0 count Ensure that at least one CCCR counter in the same group as the tagging ESCR is enabled for those performance metrics that require two ESCRs and tagging uops for at retirement counting For the steppings affected see the Summary Tables of Changes IA32 MCO ADDR and IA32 MCO MISC Registers Will Contain Invalid or Stale Data Following a Data Address or Response Parity Error If the processor experiences a data address or response parity error the ADDRV and MISCV bits of the IA32_MCO_STATUS register are set but the 1432 MCU ADDR and IA32_MCO0_MISC registers are not loaded with data regarding the error When this erratum occurs the A32_MCO_ADDR and IA32 MCU MISC registers will contain invalid or
37. n execution before the RDTSC instruction operation is performed The RDMSR and WRMSR instructions read and write the time stamp counter treating the time stamp counter as an ordinary MSR address 10H In the Pentium 4 Intel Xeon and P6 family processors all 64 bits of the time stamp counter are read using RDMSR just as with RDTSC When WRMSR is used to write the time stamp counter on processors before family OFH models 03H 04H only the low order 32 bits of the time stamp counter can be written the high order 32 bits are cleared to 0 For family OFH models 03H 04H all 64 bits are writeable 15 10 9 Counting Clocks The count of cycles also known as clockticks forms the basis for measuring how long a program takes to execute Clockticks are also used as part of efficiency ratios like cycles per instruction CPI Processor clocks may stop ticking under circumstances like the following e The processor is halted when there is nothing for the CPU to do For example the processor may halt to save power while the computer is servicing an I O request When Hyper Threading Specification Update 35 intel Technology is enabled both logical processors must be halted for performance monitoring counters to be powered down e The processor is asleep as a result of being halted or because of a power management scheme There are different levels of sleep In the some deep sleep levels the time stamp counter stops counting There
38. ng of Performance Counters Does Not Work Correctly When Forced Overflow Is Enabled The performance counters are organized into pairs When the CASCADE bit of the Counter Configuration Control Register CCCR is set a counter that overflows will continue to count in the other counter of the pair The FORCE_OVF bit forces the counters to overflow on every non zero increment When the FORCE_OVF bit is set the counter overflow bit will be set but the counter no longer cascades The performance counters do not cascade when the FORCE_OVF bit is set None identified For the steppings affected see the Summary Tables of Changes Specification Update intel Problem Implication Workaround Status V14 Problem Implication Workaround Status V15 Problem Implication Workaround Status V16 Problem Implication Workaround Status EMON Event Counting of x87 Loads May Not Work As Expected If a performance counter is set to count x87 loads and floating point exceptions are unmasked the FPU Operand Data Pointer FDP may become corrupted When this erratum occurs the FPU Operand Data Pointer FDP may become corrupted This erratum will not occur with floating point exceptions masked If floating point exceptions are unmasked then performance counting of x87 loads should be disabled For the steppings affected see the Summary Tables of Changes Speculative Page Fault May Cause Livelock
39. o Occur to the Same Cache Line Address as an Outstanding Bus Read Line BRL or Bus Read Invalidate Line BRIL V26 X Fixed L2 Cache May Contain Stale Data in the Exclusive State V27 X X Fixed Re mapping the APIC Base Address to a Value Less Than or Equal to 0xDC001000 may Cause IO and Special Cycle Failure V28 X X Fixed Erroneous BIST Result Found in EAX Register After Reset V29 Fixed Processor Does not Flag GP on Non zero Write to Certain MSRs van xX x xX NoFix Simultaneous Assertion of A20M and INIT may Result in Incorrect Data Fetch V31 X X PlanFix Processor Does not Respond to Break Requests From ITP V32 Fixed Processor Signature Returns Incorrect Number of ITLB Entries V33 x x x NoFix A Write to APIC Registers Sometimes May Appear to Have Not Occurred V34 Fixed Store to Load Data Forwarding may Result in Switched Data Bytes V35 X X X NoFix Parity Error in the L1 Cache may Cause the Processor to Hang The TCK Input in the Test Access Port TAP is Sensitive to Low V36 X X Fixed Clock Edge Rates and Prone to Noise Coupling Onto TCK s Rising or Falling Edges V37 x x x NoFix The State of the Resume Flag RF Flag in a Task State Segment TSS May be Incorrect van xX x x NoFix Changes to CR3 Register do not Fence Pending Instruction Page Walks V39 X X X NoFix System Bus Interrupt Messages without Data that Receive a 10 Specification Update Steppings NO Plans ERRATA BO C1 D1 HardFailure Response May Hang the Processor
40. orkaround Status V2 Problem Implication Workaround Status I O Restart in SMM may Fail after Simultaneous Machine Check Exception MCE If an I O instruction IN INS REP INS OUT OUTS or REP OUTS is being executed and if the data for this instruction becomes corrupted the processor will signal a Machine Check Exception MCE If the instruction is directed at a device that is powered down the processor may also receive an assertion of SMI Since MCEs have higher priority the processor will call the MCE handler and the SMI assertion will remain pending However upon attempting to execute the first instruction of the MCE handler the SMI will be recognized and the processor will attempt to execute the SMM handler If the SMM handler is completed successfully it will attempt to restart the I O instruction but will not have the correct machine state due to the call to the MCE handler A simultaneous MCE and SMI assertion may occur for one of the I O instructions above The SMM handler may attempt to restart such an I O instruction but will have an incorrect state due to the MCE handler call leading to failure of the restart and shutdown of the processor If a system implementation must support both SMM and board I O restart the first thing the SMM handler code should do is check for a pending MCE If there is an MCE pending the SMM handler should immediately exit via an RSM instruction and allow the MCE handler
41. re changes frequency This is the architectural behavior moving forward To determine average processor clock frequency Intel recommends the use of Performance Monitoring logic to count processor core clocks over the period of time for which the average is required See Section 15 10 9 and Appendix A in this manual for more information The RDTSC instruction reads the time stamp counter and is guaranteed to return a monotonically increasing unique value whenever executed except for a 64 bit counter wraparound Intel guarantees that the time stamp counter will not wraparound within 10 years after being reset The period for counter wrap is longer for Pentium 4 Intel Xeon P6 family and Pentium processors Normally the RDTSC instruction can be executed by programs and procedures running at any privilege level and in virtual 8086 mode The TSD flag allows use of this instruction to be restricted to programs and procedures running at privilege level 0 A secure operating system would set the TSD flag during system initialization to disable user access to the time stamp counter An operating system that disables user access to the time stamp counter should emulate the instruction through a user accessible programming interface The RDTSC instruction is not serializing or ordered with other instructions It does not necessarily wait until all previous instructions have been executed before reading the counter Similarly subsequent instructions may begi
42. riginating bus rather than invalid state in reaction to a BWIL or BLW For the steppings affected see the Summary Tables of Changes Specification Update intel Problem Implication Workaround Status V50 Problem Implication Workaround Status Control Register 2 CR2 Can be Updated during a REP MOVS STOS Instruction with Fast Strings Enabled Under limited circumstances while executing a REP MOVS STOS string instruction with fast strings enabled it is possible for the value in CR2 to be changed as a result of an interim paging event normally invisible to the user Any higher priority architectural event that arrives and is handled while the interim paging event is occurring may see the modified value of CR2 The value in CR2 is correct at the time that an architectural page fault is signaled Intel has not observed this erratum with any commercially available software None Identified For the steppings affected see the Summary Tables of Changes Writing the Local Vector Table LVT when an Interrupt is Pending May Cause an Unexpected Interrupt If a local interrupt is pending when the LVT entry is written an interrupt may be taken on the new interrupt vector even if the mask bit is set An interrupt may immediately be generated with the new vector when a LVT entry is written even if the new LVT entry has the mask bit set If there is no Interrupt Service Routine ISR set up for that vector the system
43. s table and System Bus Reset and Configuration Timings figure of the Mobile Intel Celeron Processor on 13 Micron Process in Micro FCPGA Package Datasheet This change will be incorporated in the next revision of the datasheet BRO Maximum Hold Time Specification Change Currently it states Table 21 System Bus AC Specifications Reset Conditions T Parameter Min Max Unit Figure Notes T45 Reset Configuration Signals A 31 3 BRO INIT SMI 4 BCLKs 13 1 Setup Time T46 Reset Configuration Signals A 31 3 BHOR INIT SMI Hold Time 2 20 BCLKs 13 2 NOTES 1 Before the deassertion of RESET 2 After clock that deasserts RESET It should state Table 21 System Bus AC Specifications Reset Conditions T Parameter Min Max Unit Figure Notes T45 Reset Configuration Signals A 31 3 BRO INIT SMI Setup Time G 19 1 T46 Reset Configuration Signals A 31 3 INIT SMI 2 20 BCLKs 13 2 Hold Time T47 Reset Configuration Signal BRO Hold Time 2 2 BCLKs 13 2 NOTES 1 Before the deassertion of RESET 2 After clock that deasserts RESET Specification Update imings The following figure will be modified to reflect this change Figure 12 System Bus Reset and Configuration T lt A s 5 Sk ki 252 2 82 8 Tx T46 Reset Configuration Signals A 31 3 SMI and INIT Hold Time Tw 145 Reset Config
44. s an example during execution of a REP MOVSW instruction the first iteration a load matches DRO and DR2 and sets DR6 as FFFFOFF5h On a subsequent iteration of the instruction a load matches only DRO The DR6 register is expected to still contain FFFFOFF5h but the processor will update DR6 to FFFFOFF 1h e A Data breakpoint that is set on a load to uncacheable memory may be ignored due to an internal segment register access conflict In this case the system will continue to execute instructions bypassing the intended breakpoint Avoiding having instructions that access segment descriptor registers e g LGDT LIDT close to the UC load and avoiding serialized instructions before the UC load will reduce the occurrence of this erratum Certain debug mechanisms do not function as expected on the processor None identified For the steppings affected see the Summary Tables of Changes Specification Update intel V11 Problem Machine Check Architecture Error Reporting and Recovery May Not Work As Expected When the processor detects errors it should attempt to report and or recover from the error In the situations described below the processor does not report and or recover from the error s as intended When a transaction is deferred during the snoop phase and subsequently receives a Hard Failure response the transaction should be removed from the bus queue so that the processor may proceed Instead the transaction is not properl
45. so as not to hang the processor The processor may hang None identified For the steppings affected see the Summary Tables of Changes Memory Type of the Load Lock Different from its Corresponding Store Unlock A use once protocol is employed to ensure that the processor in a multi agent system may access data that is loaded into its cache on a Read for Ownership operation at least once before it is snooped out by another agent This protocol is necessary to avoid a multi agent livelock scenario in which the processor cannot gain ownership of a line and modify it before that data is snooped out by another agent In the case of this erratum split load lock instructions incorrectly trigger the use once protocol A load lock operation accesses data that splits across a page boundary with both pages of WB memory type The use once protocol activates and the memory type for the split halves get forced to UC Since use once does not apply to stores the store unlock instructions go out as WB memory type The full sequence on the bus is locked partial read UC partial read UC partial write WB locked partial write WB The use once protocol should not be applied to load locks When this erratum occurs the memory type of the load lock will be different than the memory type of the store unlock operation This behavior load locks and store unlocks having different memory types does not introduce any functional failures such as system hangs or m
46. specification in greater detail or further highlight a specification s impact to a complex design situation These clarifications will be incorporated in the next release of the specifications Specification Changes are modifications to the current published specifications for the Intel Pentium 4 processor These changes will be incorporated in the next release of the specifications Specification Update 7 intel Summary of Changes The following table indicates the Errata Documentation Changes Specification Clarifications or Specification Changes that apply to Intel Pentium 4 processors Intel intends to fix some of the errata in a future stepping of the component and to account for the other outstanding issues through documentation or specification changes as noted This table uses the following notations Codes Used in Summary Table Stepping Status X No mark or Blank Box apply to listed stepping Doc PlanFix Fixed NoFix PKG AP Shaded Erratum Specification Change or Clarification that applies to this stepping This erratum is fixed in listed stepping or specification change does not Document change or update that will be implemented This erratum may be fixed in a future of the product This erratum has been previously fixed There are no plans to fix this erratum This column refers to errata on the Mobile Intel Celeron Processor on 13 Micron Process in Micro FCPGA Package substrate
47. tel Mobile Intel Celeron Processor on 13 Micron Process in Micro FCPGA Package Specification Update October 2005 Notice The mobile Intel Celeron processor may contain design defects or errors known as errata which may cause the product to deviate from published specifications Current characterized errata are documented in this Specification Update Document Number 251309 028 INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL PRODUCTS NO LICENSE EXPRESS OR IMPLIED BY ESTOPPEL OR OTHERWISE TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT EXCEPT AS PROVIDED IN INTELS TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS INTEL ASSUMES NO LIABILITY WHATSOEVER AND INTEL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO SALE AND OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR PARTICULAR PURPOSE MERCHANTABILITY OR INFRINGEMENT OR ANY PATENT COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT Intel products are not intended for use in medical life saving or life sustaining applications Intel may make changes to specifications and product descriptions at any time without notice Designers must not rely on the absence or characteristics of any features or instructions marked reserved or undefined Intel reserves these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them
48. tem bus A subsequent 8 byte store unlock is expected but instead a 4 byte store unlock occurs Correct data is provided since only the lower bytes change however external logic monitoring the data transfer may be expecting an 8 byte store unlock No known commercially available chipsets are affected by this erratum None identified For the steppings affected see the Summary Tables of Changes Specification Update 21 V17 Problem Implication Workaround Status V18 Problem Implication Workaround Status V19 Problem Implication Workaround Status 22 intel Multiple Accesses to the Same S State L2 Cache Line and ECC Error Combination May Result in Loss of Cache Coherency When a Read for Ownership RFO cycle has a 64 bit address match with an outstanding read hit on a line in the L2 cache which is in the S state AND that line contains an ECC error the processor should recycle the RFO until the ECC error is handled Due to this erratum the processor does not recycle the RFO and attempts to service both the RFO and the read hit at the same time When this erratum occurs cache may become incoherent None identified For the steppings affected see the Summary Tables of Changes Processor May Hang When Resuming from Deep Sleep State When resuming from the Deep Sleep state the address strobe signals ADSTB 1 0 may become out of phase with respect to the system bus clock BCLK
49. tion it will not be retried Transaction Is Not Retried after BINIT When this erratum occurs locked transactions will unexpectedly not be retried None identified For the steppings affected see the Summary Tables of Changes Invalid Opcode OFFFh Requires a ModRM Byte Some invalid opcodes require a ModRM byte or other following bytes while others do not The invalid opcode OFFFh did not require a ModRM byte in previous generation Intel architecture processors but does in the Intel Pentium 4 processor The use of an invalid opcode OFFFh without the ModRM byte may result in a page or limit fault on the Intel Pentium 4 processor Use a ModRM byte with invalid OFFFh opcode For the steppings affected see the Summary Tables of Changes FSW May Not Be Completely Restored after Page Fault on FRSTOR or FLDENV Instructions If the FPU operating environment or FPU state operating environment and register stack being loaded by an FLDENV or FRSTOR instruction wraps around a 64Kbyte or 4Gbyte boundary and a page fault PF or segment limit fault 44GP or SS occurs on the instruction near the wrap boundary the upper byte of the FPU status word FSW might not be restored If the fault handler does not restart program execution at the faulting instruction stale data may exist in the FSW When this erratum occurs stale data will exist in the FSW Ensure that the FPU operating environment and FPU state do not cross 64Kbyte or
50. to execute If there is no MCE pending the SMM handler may proceed with its normal operation For the steppings affected see the Summary Tables of Changes MCA Registers May Contain Invalid Information if RESET Occurs and PWRGOOD Is Not Held Asserted This erratum can occur as a result either of the following events e PWRGOOD is de asserted during a RESET assertion causing internal glitches that may result in the possibility that the MCA registers latch invalid information e Or during a reset sequence if the processor s power remains valid regardless of the state of PWRGOOD and RESET is re asserted before the processor has cleared the MCA registers the processor will begin the reset process again but may not clear these registers When this erratum occurs the information in the MCA registers may not be reliable Ensure that PWRGOOD remains asserted throughout any RESET assertion and that RESET is not re asserted while PWRGOOD is de asserted For the steppings affected see the Summary Tables of Changes Specification Update 15 V3 Problem Implication Workaround Status V4 Problem Implication Workaround Status V5 Problem Implication Workaround Status 16 intel If the first transaction of a locked sequence receives a HITM and DEFER during the snoop phase it should be retried and the locked sequence restarted However if BINIT is also asserted during this transac
51. ulative load operation hits the L2 cache and receives a correctable error the IA32_MC1_STATUS register may be updated with incorrect information The 1432 MC1 STATUS register should not be updated for speculative loads When this erratum occurs the 1432 MC1 STATUS register will contain incorrect information for correctable errors None identified For the steppings affected see the Summary Tables of Changes Debug Mechanisms May Not Function As Expected Certain debug mechanisms may not function as expected on the processor The cases are as follows e When the following conditions occur 1 An FLD instruction signals a stack overflow or underflow 2 the FLD instruction splits a page boundary or a 64 byte cache line boundary 3 the instruction matches a Debug Register on the high page or cache line respectively and 4 the FLD has a stack fault and a memory fault on a split access the processor will only signal the stack fault and the debug exception will not be taken e When a data breakpoint is set on the ninth and or tenth byte s of a floating point store using the Extended Real data type and an unmasked floating point exception occurs on the store the break point will not be captured e When any instruction has multiple debug register matches and any one of those debug registers is enabled in DR7 all of the matches should be reported in DR6 when the processor goes to the debug handler This is not true during a REP instruction A
52. uration Signals Setup Time Ty 147 Reset Configuration signal BRO Hold Time Tv T13 RESET Pulse Width 39 Specification Update Documentation Changes 40 Note The Documentation Changes listed in this section apply to the following documents e Mobile Intel Celeron Processor on 13 Micron Process in Micro FCPGA Package Datasheet Document Number 251308 Documentation changes for IA 32 Intel Architecture Software Developer s Manual volumes 1 2 and 3 are posted in a separate document JA 32 Intel Architecture Software Developer s Manual Documentation Changes This document has been posted to http developer intel com All Documentation Changes will be incorporated into a future version of the appropriate mobile Intel Celeron processor on 0 13 micron process in Micro FCPGA package documentation There are no Documentation Changes in this Specification Update revision Specification Update
53. vailable the Address Valid bit in the IA32 MC Status register should not be set In instances where an L1 parity error occurs and the address is not available because the linear to physical address translation is not complete or an internal resource conflict has occurred the Address Valid bit is incorrectly set The processor may hang when an instruction code fetch receives a hard failure response from the system bus This occurs because the bus control logic does not return data to the core leaving the processor empty 1432 MC0 STATUS MSR does indicate that a hard fail response occurred The processor may hang when the following events occur and the machine check exception is enabled CR4 MCE 1 A processor that has it s STPCLK pin asserted will internally enter the Stop Grant State and finally issue a Stop Grant Acknowledge special cycle to the bus If an uncorrectable error is generated during the Stop Grant process it is possible for the Stop Grant special cycle to be issued to the bus before the processor vectors to the machine check handler Once the chipset receives its last Stop Grant special cycle it is allowed to ignore any bus activity from the processors As a result processor accesses to the machine check handler may not be acknowledged resulting in a processor hang The processor is unable to correctly report and or recover from certain errors None identified For the steppings affected see the Summary Tables of Changes Cascadi
54. wer power state When resuming from the lower power state it may be possible to take the single step trap before the execution of the original FP instruction completes A Single Step trap will be taken when not expected None identified For the steppings affected see the Summary Tables of Changes Specification Update 31 V47 intel BTS Branch Trace Store and PEBS Precise Event Based Sampling May Update Memory outside the BTS PEBS Buffer Problem Ifthe BTS PEBS buffer is defined such that Implication Workaround Status V48 Problem Implication Workaround Status 32 The difference between BTS PEBS buffer base and BTS PEBS absolute maximum is not an integer multiple of the corresponding record sizes BTS PEBS absolute maximun is less than a record size from the end of the virtual address space The record that would cross BTS PREBS absolute maximum will also continue past the end of the virtual address space Software that uses BTS PEBS near the 4 G boundary IA 32 or 2464 boundary EMT64T mode and defines the buffer such that it does not hold an integer multiple of records can update memory outside the BTS PEBS buffer Define BTS PEBS buffer such that BTS PEBS absolute maximum minus BTS PEBS buffer base is integer multiple of the corresponding record sizes as recommended in the A 32 Intel Architecture Software Developer s Manual Volume 3 For the steppings affected see the Summary Tables
55. will GP fault If the ISR does not do an End of Interrupt EOD the bit for the vector will be left set in the in service register and mask all interrupts at the same or lower priority Any vector programmed into an LVT entry must have an ISR associated with it even if that vector was programmed as masked This ISR routine must do an EOI to clear any unexpected interrupts that may occur The ISR associated with the spurious vector does not generate an EOI therefore the spurious vector should not be used when writing the LVT For the steppings affected see the Summary Tables of Changes Specification Update 33 Specification Clarifications V1 V2 The Specification Clarifications listed in this section apply to the following documents e Mobile Intel Celeron Processor on 13 Micron Process in Micro FCPGA Package Datasheet Document Number 251308 All Specification Clarifications will be incorporated into a future version of the appropriate mobile Intel Celeron processor on 0 13 micron process in Micro FCPGA Package documentation Clarifying DBI Definition for all Processors with Intel NetBurst Microarchitecture The definition of DBI signals will be clarified for Intel Pentium 4 Processors with Intel NetBurst Micro architecture The new definition will state DBI 3 0 are source synchronous and indicate the polarity of the D 63 0 signals The DBI 3 0 signals are activated when the data on the data bus is inverted If mor
56. xpected scenario to system logic within the chipset The processor may not be able to fully execute the machine check handler in response to the fatal cache error if system logic does not ensure forward progress on the system bus under this scenario System logic should ensure completion of the outstanding transactions Note that during recovery from a fatal data ECC error memory image coherency of the BWL with respect to BRL BRIL transactions is not important Forward progress is the primary requirement For the steppings affected see the Summary Tables of Changes Specification Update intel V26 Problem Implication Workaround Status V27 Problem Implication Workaround Status L2 Cache May Contain Stale Data in the Exclusive State If a cacheline A is in Modified M state in the write combining WC buffers and in the Invalid 1 state in the L2 cache and its adjacent sector B is in the Invalid 1 state and the following scenario occurs 1 A read to B misses in the L2 cache and allocates cacheline B and its associated second sector pre fetch into an almost full bus queue 2 A Bus Read Line BRL to cacheline B completes with HIT and fills data in Shared S state The bus queue full condition causes the prefetch to cacheline A to be cancelled cacheline A will remain M in the WC buffers and I in the L2 while cacheline B will be in the S state Then if the further conditions occur 1 Cache
57. y removed from the bus queue the bus queue is blocked and the processor will hang When a hardware prefetch results in an uncorrectable tag error in the L2 cache MCU STATUS UNCOR and MCO_STATUS PCC are set but no Machine Check Exception MCE is signaled No data loss or corruption occurs because the data being prefetched has not been used If the data location with the uncorrectable tag error is subsequently accessed an MCE will occur However upon this MCE or any other subsequent MCE the information for that error will not be logged because MCU STATUS UNCOR has already been set and the MCA status registers will not contain information about the error which caused the MCE assertion but instead will contain information about the prefetch error event When the reporting of errors is disabled for Machine Check Architecture MCA Bank 2 by setting all MC2_CTL register bits to 0 uncorrectable errors should be logged in the IA32_MC2_STATUS register but no machine check exception should be generated Uncorrectable loads on bank 2 which would normally be logged in the IA32_MC2_STATUS register are not logged When one half of a 64 byte instruction fetch from the L2 cache has an uncorrectable error and the other 32 byte half of the same fetch from the L2 cache has a correctable error the processor will attempt to correct the correctable error but cannot proceed due to the uncorrectable error When this occurs the processor will hang When an L
Download Pdf Manuals
Related Search