HP dc7700
Contents
1. 1 Remove disengage any security devices that prohibit opening the computer 2 Remove all removable media such as diskettes or compact discs from the computer 3 Turn off the computer properly through the operating system then turn off any external devices 4 Disconnect the power cord from the power outlet and disconnect any external devices A CAUTION Regardless of the power on state voltage is always present on the system board as long as the system is plugged into an active AC outlet You must disconnect the power cord to avoid damage to the internal components of the computer 10 Chapter 2 Hardware Upgrades ENWW 5 Use the Smart Cover FailSafe Key to remove the two tamper proof screws that secure the Smart Cover Lock to the chassis Figure 2 1 Removing the Smart Cover Lock Screws 6 Remove the access panel To reattach the Smart Cover Lock secure the lock in place with the tamper proof screws ENWW Unlocking the Smart Cover Lock 11 Removing the Computer Access Panel 1 2 a 4 Remove disengage any security devices that prohibit opening the computer Remove all removable media such as diskettes or compact discs from the computer Turn off the computer properly through the operating system then turn off any external devices Disconnect the power cord from the power outlet and disconnect any external devices CAUTION Regardless of the power on state voltage is always present on the system board as long a2. ENWW F FailSafe Key 10 front bezel removing 14 removing blanks 16 replacing 15 front panel components 2 G guide screws 29 H hard drive installing 33 removing 27 restoring software 35 headphone connector 2 l installation guidelines 9 installing battery 43 diskette drive 30 drive cables 29 expansion card 21 guide screws 29 hard drive 33 media card reader 30 memory 17 optical drive 30 restore software 35 security locks 47 K keyboard components 5 connector 4 L line in connector 4 line out connector 4 locks cable lock 47 padlock 48 Smart Cover Lock 10 M media card reader features 3 installing 30 removing 27 memory installing 17 populating sockets 18 specifications 17 microphone connector 2 4 minitower conversion 38 monitor connector 4 mouse connector 4 special functions 7 N network connector 4 O optical drive cleaning 52 defined 2 installing 30 precautions 52 removing 27 P parallel connector 4 PCI card 21 23 PCI Express card 21 24 power supply 41 product ID location 7 Index 53 R rear panel components 4 removing battery 43 bezel blanks 16 computer access panel 12 drives from drive bay 27 expansion card 21 expansion slot cover 23 front bezel 14 media card reader 27 PClcard 23 PCI Express card 24 Smart Cover Lock 10 S security cable lock 47 padlock 48 Smart Cover Lock 10 serial connector 4 serial number location 7 shipping preparation 52
3. EX NOTE The hard drive locks automatically when the system power is turned off 2 Remove and store all removable media 3 Inserta blank diskette into the diskette drive to protect the drive while in transit Do not use a diskette on which you have stored or plan to store data 4 Turn off the computer and external devices 5 Disconnect the power cord from the electrical outlet then from the computer 6 Disconnect the system components and external devices from their power sources then from the computer EX NOTE Ensure that all boards are seated properly and secured in the board slots before shipping the computer 7 Pack the system components and external devices in their original packing boxes or similar packaging with sufficient packing material to protect them 52 Appendix E Computer Operating Guidelines Routine Care and Shipping Preparation ENWW Index A access panel locking and unlocking 10 47 removing 12 replacing 13 audio connectors 2 4 B backup and recovery 35 battery replacement 43 03 changing computer configuration 36 38 computer operating guidelines 51 connecting drive cables 29 D desktop conversion 36 DIMMs See memory diskette drive installing 30 removing 27 drives connecting cables 29 installing 29 locations 26 removing 27 E electrostatic discharge preventing damage 49 expansion card installing 21 removing 21 slot locations 21 expansion slot cover removing 23 replacing 24
4. MagicGate Memory Duo Memory Stick Select Memory Stick Duo MS Duo Memory Stick PRO MS PRO Memory Stick PRO Duo MS PRO Duo Media Card Reader Components 3 Rear Panel Components 4 ADS AN AR i Table 1 3 Rear Panel Components 1 Power Cord Connector 7 amp Parallel Connector 2 PS 2 Mouse Connector green 8 Monitor Connector 3 PS 2 Keyboard Connector purple 9 J Line Out Connector for powered audio devices green 4 eS Universal Serial Bus USB 10 J Line In Audio Connector blue 5 lOlOl Serial Connector 11 amp Microphone Connector pink 6 RJ 45 Network Connector EX NOTE Arrangement and number of connectors may vary by model The monitor connector on the system board is inactive when a PCI Express graphics card is installed in the computer Ifa PCI graphics card is installed the connectors on the card and the system board may be used at the same time Some settings may need to be changed in Computer Setup to use both connectors For information about Boot Order refer to the Computer Setup F10 Utility Guide on the Documentation and Diagnostics CD Chapter 1 Product Features ENWW Keyboard ENWW G A20 Bees 0998 Oro PIP TE PTE TESTS ley eye 000 60049000000 en Table 1 4 Keyboard Components 1 Function Keys Perform special functions depending on the software application being used ee Te U Keys available in select geog
5. a 3 5 inch SATA Hard Drive into an Internal Drive Bay EX NOTE Before you remove the old hard drive be sure to back up the data from the old hard drive so that you can transfer the data to the new hard drive Also if you are replacing the primary hard drive make sure you have the Restore Plus CD set that you created when you initially set up the computer to restore the operating system software drivers and any software applications that were preinstalled on the computer If you do not have this CD set create it now Refer to the HP Backup and Recovery Manager User Guide in the Windows Start menu for more information You may wish to print this guide for easy reference The system does not support Parallel ATA PATA hard drives To install a hard drive in a 3 5 inch internal drive bay 1 Remove disengage any security devices that prohibit opening the computer 2 Remove all removable media such as diskettes or compact discs from the computer 3 Turn off the computer properly through the operating system then turn off any external devices 4 Disconnect the power cord from the power outlet and disconnect any external devices CAUTION Regardless of the power on state voltage is always present on the system board as long as the system is plugged into an active AC outlet You must disconnect the power cord to avoid damage to the internal components of the computer 5 Remove the computer access panel CAUTION After remov
6. always present on the system board as long as the system is plugged into an active AC outlet You must disconnect the power cord to avoid damage to the internal components of the computer Remove the computer access panel CAUTION After removing the access panel look for the LED on the system board to the right of the DIMM sockets If the LED is illuminated the system still has power Turn off the computer and remove the power cord before proceeding Remove the front bezel Gently pull the subpanel with the bezel blanks secured in it away from the front bezel then remove the desired bezel blank ZN CAUTION Hold the subpanel straight when you pull it away from the front bezel Pulling the subpanel away at an angle could damage the pins that align it within the front bezel Figure 2 6 Removing Bezel Blanks from the Subpanel Desktop Shown ES NOTE When replacing the subpanel ensure that the aligning pins and any remaining bezel blanks are in their proper orientation The logo on the subpanel should be located at the bottom of the subpanel when properly oriented 16 Chapter 2 Hardware Upgrades ENWW Installing Additional Memory The computer comes with double data rate 2 synchronous dynamic random access memory DDR2 SDRAM dual inline memory modules DIMMs DIMMs The memory sockets on the system board can be populated with up to four industry standard DIMMs These memory sockets are populated with at lea
7. information on backing up the CMOS settings Static electricity can damage the electronic components of the computer or optional equipment Before beginning these procedures ensure that you are discharged of static electricity by briefly touching a grounded metal object NOTE The lifetime of the lithium battery can be extended by plugging the computer into a live AC wall socket The lithium battery is only used when the computer is NOT connected to AC power HP encourages customers to recycle used electronic hardware HP original print cartridges and rechargeable batteries For more information about recycling programs go to http www hp com recycle Remove disengage any security devices that prohibit opening the computer Remove all removable media such as diskettes or compact discs from the computer Turn off the computer properly through the operating system then turn off any external devices Disconnect the power cord from the power outlet and disconnect any external devices CAUTION Regardless of the power on state voltage is always present on the system board as long as the system is plugged into an active AC outlet You must disconnect the power cord to avoid damage to the internal components of the computer 43 5 Remove the computer access panel CAUTION After removing the access panel look for the LED on the system board to the right of the DIMM sockets If the LED is illuminated the system still has power
8. media card reader later on To verify the type and size of the storage devices installed in the computer run Computer Setup Refer to the Computer Setup F10 Utility Guide on the Documentation and Diagnostics CD for more information 26 Chapter 2 Hardware Upgrades ENWW Removing a Drive from a Drive Bay A mM ENWW CAUTION All removable media should be taken out of a drive before removing the drive from the computer Remove disengage any security devices that prohibit opening the computer Remove all removable media such as diskettes or compact discs from the computer Turn off the computer properly through the operating system then turn off any external devices Disconnect the power cord from the power outlet and disconnect any external devices CAUTION Regardless of the power on state voltage is always present on the system board as long as the system is plugged into an active AC outlet You must disconnect the power cord to avoid damage to the internal components of the computer Remove the computer access panel CAUTION After removing the access panel look for the LED on the system board to the right of the DIMM sockets If the LED is illuminated the system still has power Turn off the computer and remove the power cord before proceeding Remove the front bezel Disconnect the power and data cables on the back of the drive CAUTION When removing the cables pull the tab or connector instead of the cabl
9. operate in single channel mode dual channel mode or flex mode depending on how the DIMMs are installed e The system will operate in single channel mode if the DIMM sockets are populated in one channel only e The system will operate in a higher performing dual channel mode if the total memory capacity of the DIMMs in Channel A is equal to the total memory capacity of the DIMMs in Channel B The technology and device width can vary between the channels For example if Channel A is populated with two 256MB DIMMs and Channel B is populated with one 512MB DIMM the system will operate in dual channel mode e The system will operate in flex mode if the total memory capacity of the DIMMs in Channel A is not equal to the total memory capacity of the DIMMs in Channel B In flex mode the channel populated with the least amount of memory describes the total amount of memory assigned to dual channel and the remainder is assigned to single channel For optimal speed the channels should be balanced so that the largest amount of memory is spread between the two channels For example if you are populating the sockets with one 1GB DIMM two 512MB DIMMs and one 256MB DIMM one channel should be populated with the 1GB DIMM and one 256MB DIMM and the other channel 18 Chapter 2 Hardware Upgrades ENWW ENWW should be populated with the two 512MB DIMMs With this configuration 2 GB will run as dual channel and 256 MB will run as single channel In any mo
10. optional feature included on some models only The Smart Cover Lock is a software controllable cover lock controlled by the setup password This lock prevents unauthorized access to the internal components The computer ships with the Smart Cover Lock in the unlocked position For more information about locking the Smart Cover Lock refer to the Desktop Management Guide on the Documentation and Diagnostics CD Smart Cover FailSafe Key If you enable the Smart Cover Lock and cannot enter your password to disable the lock you will need a Smart Cover FailSafe Key to open the computer cover You will need the key to access the internal computer components in any of the following circumstances e Power outage e Startup failure e PC component for example processor or power supply failure e Forgotten password EX NOTE The Smart Cover FailSafe Key is a specialized tool available from HP Be prepared order this key before you need one To obtain a FailSafe Key e Contact an authorized HP reseller or service provider Order PN 166527 001 for the wrench style key or PN 166527 002 for the screwdriver bit key e Refer to the HP Web site http www hp com for ordering information e Call the appropriate number listed in the warranty or in the Support Telephone Numbers guide on the Documentation and Diagnostics CD Using the Smart Cover FailSafe Key to Remove the Smart Cover Lock To open the access panel with the Smart Cover Lock engaged
11. plugged into an active AC outlet You must disconnect the power cord to avoid damage to the internal components of the computer Remove the computer access panel CAUTION After removing the access panel look for the LED on the system board to the right of the DIMM sockets If the LED is illuminated the system still has power Turn off the computer and remove the power cord before proceeding Remove the front bezel Disconnect all power and data cables from the back of the drives in the 5 25 inch drive bays To release the drives from the 5 25 inch drive bay lift the release tab on the green latch drive bracket for the drive While lifting the release tab slide the drive from its drive bay Repeat this step for each 5 25 inch drive Figure 2 24 Releasing the 5 25 inch Drives from the Drive Bays Minitower 36 Chapter 2 Hardware Upgrades ENWW ENWW a 10 11 12 13 14 15 Before you reinstall each drive into the chassis turn the drive so that it is perpendicular to the internal 3 5 inch drive The drive should be parallel to the green latch drive bracket Figure 2 25 Installing a Drive in the Desktop Configuration Gently slide the drive into the uppermost available bay until it snaps into place When the drive is properly inserted the drivelock will secure it Repeat this step for each drive ZN CAUTION The bottom 5 25 inch drive bay has a shorter depth than the upper two bays The bottom bay supp
12. power connectors ENWW Installing Additional Drives 31 9 10 11 12 13 14 15 Connect the power cable 1 and data cable 2 to the rear of the optical drive or diskette drive Figure 2 20 Connecting the Drive Cables Optical Drive shown If you are installing a new drive connect the opposite end of the data cable to the appropriate system board connector EX NOTE If you are installing a SATA optical drive connect the first optical drive to the white SATA connector on the system board labeled SATA1 Connect a second optical drive to the orange SATA connector labeled SATA3 If you are installing a diskette drive connect it to the connector on the system board labeled FLOPPY P10 If your are installing a media card reader install the PCI card included with the media card reader and connect the USB cable from the media card reader to the USB connector on the PCI card Remove the appropriate bezel blank from the subpanel inside the front bezel See the Removing Bezel Blanks section for more information Replace the front bezel and computer access panel Reconnect the power cord and turn on the computer Lock any security devices that were disengaged when the computer access panel was removed Reconfigure the computer if necessary Refer to the Computer Setup F10 Utility Guide on the Documentation and Diagnostics CD for instructions about using Computer Setup 32 Chapter 2 Hardware Upgrades ENWW Installing
13. until they arrive at static free workstations Place parts on a grounded surface before removing them from their containers Avoid touching pins leads or circuitry Always be properly grounded when touching a static sensitive component or assembly Grounding Methods There are several methods for grounding Use one or more of the following methods when handling or installing electrostatic sensitive parts ENWW Use a wrist strap connected by a ground cord to a grounded workstation or computer chassis Wrist straps are flexible straps with a minimum of 1 megohm 10 percent resistance in the ground cords To provide proper ground wear the strap snug against the skin Use heelstraps toestraps or bootstraps at standing workstations Wear the straps on both feet when standing on conductive floors or dissipating floor mats Use conductive field service tools Use a portable field service kit with a folding static dissipating work mat If you do not have any of the suggested equipment for proper grounding contact an HP authorized dealer reseller or service provider NOTE For more information on static electricity contact an HP authorized dealer reseller or service provider Preventing Electrostatic Damage 49 50 Appendix D Electrostatic Discharge ENWW E Computer Operating Guidelines Routine Care and Shipping Preparation Computer Operating Guidelines and Routine Care Follow these guidelines to properly set up and
14. 0 60 Hz 50 60 Hz Power Output 365 W 365 W Rated Input Current maximum 6A 100 VAC 3A 200 VAC o nn 22 ee This system utilizes an active power factor corrected power supply This allows the system to pass the CE mark requirements for use in the countries of the European Union The active power factor corrected power supply also has the added benefit of not requiring an input voltage range select switch 42 Appendix A Specifications ENWW B Battery Replacement ENWW The battery that comes with the computer provides power to the real time clock When replacing the battery use a battery equivalent to the battery originally installed in the computer The computer comes with a 3 volt lithium coin cell battery A WARNING The computer contains an internal lithium manganese dioxide battery There is a ES gt em risk of fire and burns if the battery is not handled properly To reduce the risk of personal injury Do not attempt to recharge the battery Do not expose to temperatures higher than 60 C 140 F Do not disassemble crush puncture short external contacts or dispose of in fire or water Replace the battery only with the HP spare designated for this product CAUTION Before replacing the battery it is important to back up the computer CMOS settings When the battery is removed or replaced the CMOS settings will be cleared Refer to the Computer Setup F10 Utility Guide on the Documentation and Diagnostics CD for
15. Hardware Reference Guide dc7700 Series Convertible Minitower HP Compaq Business PC invent Copyright 2006 Hewlett Packard Development Company L P The information contained herein is subject to change without notice Microsoft and Windows are trademarks of Microsoft Corporation in the U S and other countries The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services Nothing herein should be construed as constituting an additional warranty HP shall not be liable for technical or editorial errors or omissions contained herein This document contains proprietary information that is protected by copyright No part of this document may be photocopied reproduced or translated to another language without the prior written consent of Hewlett Packard Company Hardware Reference Guide HP Compaq Business PC dc7700 Series Convertible Minitower First Edition August 2006 Document part number 418620 001 ENWW About This Book This guide provides basic information for upgrading this computer model A WARNING Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life A CAUTION Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information ES NOTE Text set off in this manner provides important supplemental
16. Smart Cover Lock 10 specifications computer 41 memory 17 U unlocking access panel 10 47 USB ports front panel 2 rear panel 4 Vv ventilation guidelines 51 Ww Windows Logo key 6 54 Index ENWW
17. TA1 connectors before the light blue SATA2 and orange SATA3 connectors Connect a second SATA optical drive to the orange SATA3 connector Connect additional SATA hard drives to the next available unpopulated SATA connector on the system board in the following order SATAO SATA1 SATA3 SATA2 Connect a diskette drive to the connector labeled FLOPPY P10 The system does not support Parallel ATA PATA optical drives or PATA hard drives You may install either a third height or a half height drive into a half height bay You must install guide screws to ensure the drive will line up correctly in the drive cage and lock in place HP has provided extra guide screws installed on the chassis The hard drive uses 6 32 standard screws four of which are installed on the hard drive bracket under the access panel All other drives use M3 metric screws eight of which are installed on the diskette drive bracket under the access panel The HP supplied metric screws are black The HP supplied standard screws are silver AR CAUTION To prevent loss of work and damage to the computer or drive ENWW If you are inserting or removing a drive shut down the operating system properly turn off the computer and unplug the power cord Do not remove a drive while the computer is on or in standby mode Before handling a drive ensure that you are discharged of static electricity While handling a drive avoid touching the connector For more information abo
18. TION After removing the access panel look for the LED on the system board to the right of the DIMM sockets If the LED is illuminated the system still has power Turn off the computer and remove the power cord before proceeding 6 Remove the front bezel Chapter 2 Hardware Upgrades ENWW 7 Install two guide screws in the lower holes on each side of the drive 1 E NOTE Optical drives diskette drives and media card readers use M3 metric guide screws Eight extra metric guide screws are provided on the diskette drive bracket under the access panel The HP supplied metric screws are black Figure 2 19 Installing a 5 25 Inch Drive in a Minitower top and Desktop bottom 8 Install the drive in the desired drive bay by sliding it all the way into the front of the drive cage until itlocks 2 The drivelock automatically secures the drive in the bay ZN CAUTION The bottom 5 25 inch drive bay has a shorter depth than the upper two bays The bottom bay supports a drive that is no more than 17 cm 6 7 inches in depth including the cables that attach to the back of the drive Do not try to force a larger drive such as an optical drive into the bottom bay This could cause damage to the drive and the system board The use of unnecessary force when installing any drive into the drive bay may result in damage to the drive ES NOTE If you are installing a third optional drive you may need to remove the strap that bundles the extra
19. Turn off the computer and remove the power cord before proceeding 6 Locate the battery and battery holder on the system board EX NOTE On some computer models it may be necessary to remove an internal component to gain access to the battery 7 Depending on the type of battery holder on the system board complete the following instructions to replace the battery Type 1 a Liftthe battery out of its holder Figure B 1 Removing a Coin Cell Battery Type 1 b Slide the replacement battery into position positive side up The battery holder automatically secures the battery in the proper position Type 2 a To release the battery from its holder squeeze the metal clamp that extends above one edge of the battery When the battery pops up lift it out 1 44 Appendix B Battery Replacement ENWW b To insert the new battery slide one edge of the replacement battery under the holder s lip with the positive side up Push the other edge down until the clamp snaps over the other edge of the battery 2 Figure B 2 Removing and Replacing a Coin Cell Battery Type 2 Type 3 a Pull back on the clip 1 that is holding the battery in place and remove the battery 2 b Insert the new battery and position the clip back into place Figure B 3 Removing a Coin Cell Battery Type 3 Ez NOTE After the battery has been replaced use the following steps to complete this procedure 8 Replace the computer access pa
20. a such as diskettes or compact discs from the computer 3 Turn off the computer properly through the operating system then turn off any external devices 4 Disconnect the power cord from the power outlet and disconnect any external devices Removing or Installing an Expansion Card 21 CAUTION Regardless of the power on state voltage is always present on the system board as long as the system is plugged into an active AC outlet You must disconnect the power cord to avoid damage to the internal components of the computer 5 Remove the computer access panel CAUTION After removing the access panel look for the LED on the system board to the right of the DIMM sockets If the LED is illuminated the system still has power Turn off the computer and remove the power cord before proceeding 6 Locate the correct vacant expansion socket on the system board and the corresponding expansion slot on the back of the computer chassis 7 Push down and out on the two green thumb tabs inside the chassis and rotate the expansion card retention latch up I m g 4 ee Figure 2 10 Opening the Expansion Slot Retainer 8 Before installing an expansion card remove the expansion slot cover or the existing expansion card 22 Chapter 2 Hardware Upgrades ENWW EX NOTE Before removing an installed expansion card disconnect any cables that may be attached to the expansion card a Ifyou are installing an expa
21. anel was removed 40 Chapter 2 Hardware Upgrades ENWW A Specifications E E_ oo_u_ ur gt Tg Ve oe m gt ss tr t x t zw sw s m m majaebuuuuu Desktop Dimensions Height 6 6 in 16 7 cm Width 17 65 in 44 8 cm Depth depth will increase if the computer is equipped witha 17 8 in 45 2 cm port security bracket Tower Dimensions Height 17 65 in 44 8 cm Width 6 6 in 16 7 cm Depth depth will increase if the computer is equipped witha 17 8 in 45 2 cm port security bracket Approximate Weight 35 Ib 15 9 kg Weight Supported maximum distributed load for Desktop 100 Ib 45 5 kg configuration only Temperature Range Operating 50 to 95 F 10 to 35 C Nonoperating 22 to 140 F 30 to 60 C Relative Humidity noncondensing Operating 10 90 10 90 Nonoperating 38 7 C max wet bulb 5 95 5 95 Maximum Altitude unpressurized Operating 10 000 ft 3048 m Nonoperating 30 000 ft 9144 m Ez NOTE Operating temperature is derated 1 0 C per 300 m 1000 ft to 3000 m 10 000 ft above sea level no direct sustained sunlight Maximum rate of change is 10 C Hr The upper limit may be limited by the type and number of options installed Heat Dissipation Maximum 1 916 BTU hr 483 kg cal hr Typical idle 375 BTU hr 95 kg cal hr Power Supply 115V 230V ENWW 41 Operating Voltage Range 90 264 VAC 90 264 VAC Rated Voltage Range 100 240 VAC 100 240 VAC Rated Line Frequency 5
22. ating DIMM Sockets for more information 8 Push the module down into the socket ensuring that the module is fully inserted and properly seated Make sure the latches are in the closed position 3 9 Repeat steps 7 and 8 to install any additional modules 10 Replace the computer access panel 11 Reconnect the power cord and turn on the computer 12 Lock any security devices that were disengaged when the computer access panel was removed The computer should automatically recognize the additional memory the next time you turn on the computer 20 Chapter 2 Hardware Upgrades ENWW Removing or Installing an Expansion Card ENWW The computer has two standard full height PCI expansion slots that can accommodate an expansion card up to 34 cm 13 4 inches in length The computer also has one PCI Express x1 expansion slot and one PCI Express x16 expansion slot Figure 2 9 Expansion Slot Locations Item Description 1 PCI expansion slot 2 PCI expansion slot 3 PCI Express x1 expansion slot 4 PCI Express x16 expansion slot ES NOTE Some models include an optional PCI extender that adds two PCI expansion slots to the board for a total of four PCI expansion slots You can install a PCI Express x1 x4 x8 or x16 expansion card in the PCI Express x16 expansion slot To remove replace or add an expansion card 1 Remove disengage any security devices that prohibit opening the computer 2 Remove all removable medi
23. care for the computer and monitor ENWW Keep the computer away from excessive moisture direct sunlight and extremes of heat and cold Operate the computer on a sturdy level surface Leave a 10 2 cm 4 inch clearance on all vented sides of the computer and above the monitor to permit the required airflow Never restrict the airflow into the computer by blocking any vents or air intakes Do not place the keyboard with the keyboard feet down directly against the front of the desktop unit as this also restricts airflow Never operate the computer with the cover or side panel removed Do not stack computers on top of each other or place computers so near each other that they are subject to each other s re circulated or preheated air If the computer is to be operated within a separate enclosure intake and exhaust ventilation must be provided on the enclosure and the same operating guidelines listed above will still apply Keep liquids away from the computer and keyboard Never cover the ventilation slots on the monitor with any type of material Install or enable power management functions of the operating system or other software including sleep states Turn off the computer before you do either of the following e Wipe the exterior of the computer with a soft damp cloth as needed Using cleaning products may discolor or damage the finish e Occasionally clean the air vents on all vented sides of the computer Lint dust an
24. d other foreign matter can block the vents and limit the airflow Computer Operating Guidelines and Routine Care 51 Optical Drive Precautions Be sure to observe the following guidelines while operating or cleaning the optical drive Operation e Do not move the drive during operation This may cause it to malfunction during reading e Avoid exposing the drive to sudden changes in temperature as condensation may form inside the unit If the temperature suddenly changes while the drive is on wait at least one hour before you turn off the power If you operate the unit immediately it may malfunction while reading e Avoid placing the drive in a location that is subject to high humidity extreme temperatures mechanical vibration or direct sunlight Cleaning e Clean the panel and controls with a soft dry cloth or a soft cloth lightly moistened with a mild detergent solution Never spray cleaning fluids directly on the unit e Avoid using any type of solvent such as alcohol or benzene which may damage the finish Safety If any object or liquid falls into the drive immediately unplug the computer and have it checked by an authorized HP service provider Shipping Preparation Follow these suggestions when preparing to ship the computer 1 Back up the hard drive files on PD discs tape cartridges CDs or diskettes Be sure that the backup media is not exposed to electrical or magnetic impulses while stored or in transit
25. de the maximum operational speed is determined by the slowest DIMM in the system Installing DIMMs A CAUTION You must disconnect the power cord before adding or removing memory modules gt p N Regardless of the power on state voltage is always supplied to the memory modules as long as the computer is plugged into an active AC outlet Adding or removing memory modules while voltage is present may cause irreparable damage to the memory modules or system board After removing the access panel look for the LED on the system board to the right of the DIMM sockets If the LED is illuminated the system still has power Turn off the computer and remove the power cord before proceeding The memory module sockets have gold plated metal contacts When upgrading the memory it is important to use memory modules with gold plated metal contacts to prevent corrosion and or oxidation resulting from having incompatible metals in contact with each other Static electricity can damage the electronic components of the computer or optional cards Before beginning these procedures ensure that you are discharged of static electricity by briefly touching a grounded metal object For more information refer to Appendix D Electrostatic Discharge When handling a memory module be careful not to touch any of the contacts Doing so may damage the module Remove disengage any security devices that prohibit opening the computer Remove all removable media s
26. e When the drive is properly inserted the drivelock will secure it Repeat this step for each drive ZN CAUTION The bottom 5 25 inch drive bay has a shorter depth than the upper two bays The bottom bay supports a drive that is no more than 17 cm 6 7 inches in depth including the cables that attach to the back of the drive Do not try to force a larger drive such as an optical drive into the bottom bay This could cause damage to the drive and the system board The use of unnecessary force when installing any drive into the drive bay may result in damage to the drive 11 Reconnect all power and data cables to the drives in the 5 25 inch drive bays 12 Remove the bezel subpanel as described in the Removing Bezel Blanks section CAUTION Hold the subpanel straight when you pull it away from the front bezel Pulling the subpanel away at an angle could damage the pins that align it within the front bezel 13 Reposition the bezel blanks within the subpanel in the proper orientation for the minitower configuration ENWW Changing from a Desktop to a MinitowerConfiguration 39 14 Reposition the subpanel rotate it 90 with the logo at the bottom then snap it back into the bezel Figure 2 29 Changing from a Desktop to a Minitower Configuration 15 Replace the front bezel and computer access panel 16 Reconnect the power cord and turn on the computer 17 Lock any security devices that were disengaged when the computer access p
27. e computer Turn off the computer properly through the operating system then turn off any external devices Disconnect the power cord from the power outlet and disconnect any external devices CAUTION Regardless of the power on state voltage is always present on the system board as long as the system is plugged into an active AC outlet You must disconnect the power cord to avoid damage to the internal components of the computer Remove the computer access panel CAUTION After removing the access panel look for the LED on the system board to the right of the DIMM sockets If the LED is illuminated the system still has power Turn off the computer and remove the power cord before proceeding Remove the front bezel Disconnect all power and data cables from the back of the drives in the 5 25 inch drive bays To release the drives from the 5 25 inch drive bay press down on the short yellow drivelock as shown While pressing the drivelock pull the drives out of the drive bay Figure 2 27 Releasing the 5 25 inch Drives from the Drive Bays Desktop 38 Chapter 2 Hardware Upgrades ENWW 9 Before you reinstall each drive into the chassis turn it so that it is in the same orientation as the internal 3 5 inch drive The bottom of the drive should be parallel to the yellow drivelock Figure 2 28 Installing a Drive in the Minitower Configuration 10 Gently slide the drive into the uppermost available bay until it snaps into plac
28. e itself to avoid damaging the cable Remove the drive from the drive bay as follows e To remove a 5 25 inch drive in the desktop configuration press down on the yellow drivelock mechanism 1 and slide the drive from the drive bay 2 Figure 2 16 Removing a 5 25 inch Drive in the Desktop Configuration Optical Drive shown Removing a Drive from a Drive Bay 27 e To remove a 3 5 inch drive or a 5 25 inch drive in the minitower configuration pull up on the green drivelock mechanism 1 for that specific drive and slide the drive from the drive bay 2 Figure 2 17 Removing a 3 5 inch Drive or a 5 25 inch Drive in the Minitower Configuration Optical Drive shown e Toremove a hard drive from and internal 3 5 inch drive bay pull up on the green hard drive drivelock mechanism 1 for that drive and slide the drive from the drive bay 2 Figure 2 18 Removing a Hard Drive 9 Store the removed drive in anti static packaging 28 Chapter 2 Hardware Upgrades ENWW Installing Additional Drives The computer supports up to five drives that may be installed in various configurations When installing additional drives follow these guidelines The primary Serial ATA SATA hard drive must be connected to the dark blue SATA connector on the system board labeled SATAO Connect the first SATA optical drive to the white SATA connector on the system board labeled SATA1 Always populate the dark blue SATAO and white SA
29. e the risk of personal injury from electrical shock hot surfaces or fire Disconnect the power cord from the wall outlet and allow the internal system components to cool before touching Do not plug telecommunications or telephone connectors into the network interface controller NIC receptacles Do not disable the power cord grounding plug The grounding plug is an important safety feature Plug the power cord in a grounded earthed outlet that is easily accessible at all times To reduce the risk of serious injury read the Safety amp Comfort Guide It describes proper workstation setup posture and health and work habits for computer users and provides important electrical and mechanical safety information This guide is located on the Web at http www hp com ergo and on the Documentation and Diagnostics CD CAUTION Static electricity can damage the electrical components of the computer or optional equipment Before beginning these procedures ensure that you are discharged of static electricity by briefly touching a grounded metal object See Appendix D Electrostatic Discharge for more information When the computer is plugged into an AC power source voltage is always applied to the system board You must disconnect the power cord from the power source before opening the computer to prevent damage to internal components Serviceability Features 9 Unlocking the Smart Cover Lock EX NOTE The Smart Cover Lock is an
30. eeceeseseneenceeteseaeeeceseeqedeedsenegedanesdeneaedeneeeetecereceenes 49 Grounding MethOdS casccsasessacieannsedaerdesnantenctenaued an dee erde beten did he see 49 Appendix E Computer Operating Guidelines Routine Care and Shipping Preparation Computer Operating Guidelines and Routine Care 424444444440snnnennnnnnnnennnnnennnnnenennnnnennnn 51 Optical Drive Pr amp cautions uuseieii ae een a aa ci 52 OO ira a dadas 52 CVG EAM Mutis tdi ek heine ii 52 DY tica ia di 52 SHIPPING PreparatiON seccional nenn nn aa ana aaa nd Ran nennen 52 NRO ii o PEEREREUEUUNERLESUEEERSSUETUERE TE 53 vi ENWW 1 Product Features Standard Configuration Features The HP Compaq Convertible Minitower features may vary depending on the model For a complete listing of the hardware and software installed in the computer run the diagnostic utility included on some computer models only Instructions for using the utility are provided in the Troubleshooting Guide on the Documentation and Diagnostics CD EX NOTE The HP Compaq Convertible Minitower computer can be easily converted to a desktop For more information see the Changing from a Minitower to a Desktop Configuration section in this guide Figure 1 1 Convertible Minitower Configuration ENWW Standard Configuration Features 1 Front Panel Components 2 Drive configuration may vary by model Table 1 1 Front Panel Components 1 5 25 inch Optica
31. et on the system board Figure 2 14 Installing an Expansion Card ES NOTE When installing an expansion card press firmly on the card so that the whole connector seats properly in the expansion card slot 12 Close the expansion card retention latch making sure that it snaps firmly into place 13 Connect external cables to the installed card if needed Connect internal cables to the system board if needed 14 Replace the computer access panel 15 Reconnect the power cord and turn on the computer 16 Lock any security devices that were disengaged when the computer access panel was removed 17 Reconfigure the computer if necessary Refer to the Computer Setup F10 Utility Guide on the Documentation and Diagnostics CD for instructions about using Computer Setup ENWW Removing or Installing an Expansion Card 25 Drive Positions Figure 2 15 Desktop and Minitower Drive Positions 1 Three 5 25 inch external drive bays for optional drives optical drives and media card reader shown 2 One 3 5 inch external drive bay for optional drives diskette drive shown 3 Two 3 5 inch internal hard drive bays AE EP PAE E a ee 1 An optional hard drive mounting bracket for these drive bays is available from HP 2 Depending on the computer configuration you may have a bezel blank in this position If you do not have a drive in this slot you may choose to install a 3 5 inch drive such as a diskette drive hard drive or
32. hes My Computer Windows Logo Key f Launches Find Document Windows Logo Key Ctrl f Windows Logo Key F1 Windows Logo Key Windows Logo Key r Launches Find Computer Launches Windows Help Locks the computer if you are connected to a network domain or allows you to switch users if you are not connected to a network domain Launches the Run dialog box Windows Logo Key u Launches the Utility Manager Windows Logo Key Tab Activates the next Taskbar button Chapter 1 Product Features ENWW Special Mouse Functions Most software applications support the use of a mouse The functions assigned to each mouse button depend on the software applications you are using Serial Number Location Each computer has a unique serial number and a product ID number that are located on the top cover ofthe computer Keep these numbers available for use when contacting customer service for assistance Figure 1 2 Serial Number and Product ID Location ENWW Special Mouse Functions 7 8 Chapter 1 Product Features ENWW 2 Hardware Upgrades Serviceability Features The computer includes features that make it easy to upgrade and service No tools are needed for most of the installation procedures described in this chapter Warnings and Cautions ENWW Before performing upgrades be sure to carefully read all ofthe applicable instructions cautions and warnings in this guide A WARNING To reduc
33. information iv About This Book ENWW Table of contents 1 Product Features standard Configuration Features u en na ahnen 1 Front Panel Components 444444444444nsnennnnnnnnnnnnnnnnnnnennnennnnnnnnnn nn nennannennnnnnnnnnnnn nennen 2 Media Card Reader Components 4444444444404400nnnnnnnnnnnnnnnnnnnannannnnnnnennnennnnnnnnannnnnnnnnnn nenn 3 Rear Panel Components 444444444s4Hsnsnnennnnnennnennnnnnennnnnnnnnannnnnnnnnnnnnnennnennennnnnnansnnnnnrnnrrnnnnnen nn 4 A E E E T E 5 Using the Windows LOGO Key uer ussu nenne EEEE AAEE ANA 6 Special Mouse Functions itsessaan eia ai aAA aaia aa aE Ea aa aAa aa 7 Serial Number Location nee ren ae ern 7 2 Hardware Upgrades Serviceability Features 4404snnnnnennnnennnnnnnnnennnnnnnnnnnnnnnnnnnnnnnnnnnnsnnnnnnnnnnnnennnennnsnnnnnnnnnnnnne rn 9 VVarnings and GAutllOns 2r 02 E EEEE E 9 Unl cking the Smart Cover Lock ea nennen 10 Smart Cover Fail Safe Key ccoo nase net 10 Using the Smart Cover FailSafe Key to Remove the Smart Cover Lock n 10 Removing the Computer Access Panel ncccccnnnnccccnnnnacccccnonconccncnnnnn coca nana n cnn nn cn rana nc 12 Replacing the Computer Access Panel ooooccccccccccccocccnccnnncnnccncnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnannninnnanas 13 Removing the Front Bezel uusserssnnennensnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnennnnnnnnennnnnnnnnennnnnnnsnnennnnnnsnnn
34. ing the access panel look for the LED on the system board to the right of the DIMM sockets If the LED is illuminated the system still has power Turn off the computer and remove the power cord before proceeding 6 Install four 6 32 standard guide screws two on each side of the drive Figure 2 21 Installing the Hard Drive Guide Screws ES NOTE The hard drive uses 6 32 standard guide screws Four extra guide screws are installed on the hard drive bracket under the access panel The HP supplied standard screws are silver ENWW Installing Additional Drives 33 7 Slide the hard drive down into the drive cage until it locks The drivelock automatically secures the drive in the bay Figure 2 22 Installing a Hard Drive into the Hard Drive Bay A CAUTION Make sure the guide screws line up with the guide slots in the drive cage The use of unnecessary force when installing any drive into the drive bay may result in damage to the drive 8 Connect the power cable 1 and data cable 2 to the rear of the hard drive Figure 2 23 Connecting the Power Cable and Data Cable to a SATA Hard Drive 9 Connect the opposite end of the data cable to the appropriate system board connector Ez NOTE If your system has only one SATA hard drive you must connect the hard drive data cable to the dark blue connector labeled SATAO to avoid any hard drive performance problems If you are adding a second hard drive connect the data cable to the nex
35. l Drives 8 5 25 inch Media Card Reader optional 2 Optical Drive Activity Lights 9 Dual State Power Button 3 3 5 inch Diskette Drive optional 10 Power On Light 4 Diskette Drive Activity Light optional 11 USB Universal Serial Bus Ports 5 Diskette Eject Button optional 12 Headphone Connector 6 Hard Drive Activity Light 13 Microphone Connector 7 Optical Drive Eject Buttons Ez NOTE An optical drive is a CD ROM DVD R RW or CD RW DVD Combo drive e 1 Some models are configured with a media card reader in the external 3 5 inch drive bay Other models have a bezel blank covering this bay Chapter 1 Product Features ENWW Media Card Reader Components ENWW The media card reader is an optional device available on some models only Refer to the following illustration and table to identify the media card reader components Table 1 2 Media Card Reader Components 1 SmartMedia xD 3 3V SmartMedia Card SM D Picture Card xD USB Universal Serial Bus Port 2 Media Card Reader Activity Light CompactFlash I II e CompactFlash Card Type 1 e CompactFlash Card Type 2 e MicroDrive 3 SD MMC miniSD MS PRO MS PRO DUO Secure Digital Card SD MiniSD MultiMediaCard MMC Reduced Size MultiMediaCard RS MMC MultiMediaCard 4 0 Mobile Plus Reduced Size MultiMediaCard 4 0 MMC Mobile MMC Micro adapter required MicroSD T Flash adapter required Memory Stick MS MagicGate Memory Stick MG
36. nel 9 Plug in the computer and turn on power to the computer 10 Reset the date and time your passwords and any special system setups using Computer Setup Refer to the Computer Setup F10 Utility Guide on the Documentation and Diagnostics CD 11 Lock any security devices that were disengaged when the computer access panel was removed ENWW 45 46 Appendix B Battery Replacement ENWW C External Security Devices ES NOTE For information on data security features refer to the Computer Setup F10 Utility Guide and the Desktop Management Guide on the Documentation and Diagnostics CD and the HP ProtectTools Security Manager Guide some models at http www hp com Installing a Security Lock The security locks displayed below and on the following page can be used to secure the computer Cable Lock Figure C 1 Installing a Cable Lock ENWW Installing a Security Lock 47 Padlock Figure C 2 Installing a Padlock 48 Appendix C External Security Devices ENWW D Electrostatic Discharge A discharge of static electricity from a finger or other conductor may damage system boards or other static sensitive devices This type of damage may reduce the life expectancy of the device Preventing Electrostatic Damage To prevent electrostatic damage observe the following precautions Avoid hand contact by transporting and storing products in static safe containers Keep electrostatic sensitive parts in their containers
37. nnnnnnnnnnn 14 Replacing the Front BeZel u ae ea ae ab ee 15 Removing Bezel Blanks 444444444440nnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnsnnnnnnnnnnnnnnnnnnnnnnnnnn ran 16 Installing Additional Mem rty 2 222er 17 BJ DRS TO 17 DDR2 SDRAM DIMMS u 4 2 2er ahnen 17 Populating DIMM Sockets sensos na Bea len 18 Installlng DIMMS 4 a ae ee 19 Removing or Installing an Expansion Card u 4444444eseennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 21 Drive POSIti ns 2 A ind abad 26 Removing a Drive from a Drive Bay 4ussssnsnnnennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnennnnnnnsnnnnnnnnensnnnnnnnnnnnnnnnn 27 Installing Additional Drives 000 oi een 29 Installing a 5 25 inch or 3 5 inch Drive into an External Drive Bay nenn 30 Installing a 3 5 inch SATA Hard Drive into an Internal Drive Bay uue een 33 Changing from a Minitower to a Desktop Configuration ooconnonnnnncnnncoccccccnnnonnnnncnanan cnn rc narrar nana 36 Changing from a Desktop to a MinitowerConfiguration 2224444404nsssnnnnnnnennnnnnennen nennen 38 Appendix A Specifications Appendix B Battery Replacement ENWW Appendix C External Security Devices Installingia Security LOCK 47 A A nenne EAA EAA 47 Paddock iii oia dhebeedsteebheadeliaaardine 48 Appendix D Electrostatic Discharge Preventing Electrostatic Damage 222 c ccceencceetecee
38. nsion card in a vacant socket remove the appropriate expansion slot cover on the back of the chassis Lift the expansion slot cover from the expansion slot Figure 2 11 Removing an Expansion Slot Cover b If you are removing a standard PCI card hold the card at each end and carefully rock it back and forth until the connectors pull free from the socket Lift the card straight up to remove it Be sure not to scrape the card against other components Figure 2 12 Removing a Standard PCI Expansion Card ENWW Removing or Installing an Expansion Card 23 c Ifyou are removing a PCI Express x16 card pull the retention arm on the back of the expansion socket away from the card and carefully rock the card back and forth until the connectors pull free from the socket Lift the card straight up to remove it Be sure not to scrape the card against other components Figure 2 13 Removing a PCI Express x16 Expansion Card 9 Store the removed card in anti static packaging 10 If you are not installing a new expansion card install an expansion slot cover to close the open slot A CAUTION After removing an expansion card you must replace it with a new card or expansion slot cover for proper cooling of internal components during operation 24 Chapter 2 Hardware Upgrades ENWW 11 To install a new expansion card slide the bracket on the end of the card down into the slot on the back of the chassis and press the card down firmly into the sock
39. on state voltage is always present on the system board as long as the system is plugged into an active AC outlet You must disconnect the power cord to avoid damage to the internal components of the computer 5 Remove the computer access panel CAUTION After removing the access panel look for the LED on the system board to the right of the DIMM sockets If the LED is illuminated the system still has power Turn off the computer and remove the power cord before proceeding 6 Push up on the two release tabs 1 then rotate the front bezel away from the chassis to release it 2 Figure 2 4 Removing the Front Bezel 14 Chapter 2 Hardware Upgrades ENWW Replacing the Front Bezel 1 Place the bottom hinge points on the front bezel in their corresponding slots in the chassis 1 Rotate the front bezel onto the chassis 2 2 3 Snap the catches at the top of the bezel into place 3 4 Snap the release tabs into place 4 Figure 2 5 Replacing the Front Bezel ENWW Replacing the Front Bezel 15 Removing Bezel Blanks 1 2 a 4 Remove disengage any security devices that prohibit opening the computer Remove all removable media such as diskettes or compact discs from the computer Turn off the computer properly through the operating system then turn off any external devices Disconnect the power cord from the power outlet and disconnect any external devices CAUTION Regardless of the power on state voltage is
40. orts a drive that is no more than 17 cm 6 7 inches in depth including the cables that attach to the back of the drive Do not try to force a larger drive such as an optical drive into the bottom bay This could cause damage to the drive and the system board The use of unnecessary force when installing any drive into the drive bay may result in damage to the drive Reconnect all power and data cables to the drives in the 5 25 inch drive bays Remove the bezel subpanel as described in the Removing Bezel Blanks section CAUTION Hold the subpanel straight when you pull it away from the front bezel Pulling the subpanel away at an angle could damage the pins that align it within the front bezel Reposition the bezel blanks within the subpanel in the proper orientation for the desktop configuration Reposition the subpanel rotate it 90 with the logo at the bottom then snap it back into the bezel Figure 2 26 Changing from a Minitower to a Desktop Configuration Replace the front bezel and computer access panel Changing from a Minitower to a Desktop Configuration 37 16 Reconnect the power cord and turn on the computer 17 Lock any security devices that were disengaged when the computer access panel was removed Changing from a Desktop to a MinitowerConfiguration 1 2 3 Remove disengage any security devices that prohibit opening the computer Remove all removable media such as diskettes or compact discs from th
41. raphic regions 1 2 Editing Keys Includes the following Insert Home Page Up Delete End and Page Down 3 Status Lights Indicate the status of the computer and keyboard settings Num Lock Caps Lock and Scroll Lock 4 Numeric Keys Work like a calculator keypad 5 Arrow Keys Used to navigate through a document or Web site These keys allow you to move left right up and down using the keyboard instead of the mouse 6 Ctrl Keys Used in combination with another key their effect depends on the application software you are using 7 Application Key Used like the right mouse button to open pop up menus in a Microsoft Office application May perform other functions in other software applications 8 Windows Logo Keys Used to open the Start menu in Microsoft Windows Used in combination with other keys to perform other functions 9 Alt Keys Used in combination with another key their effect depends on the application software you are using Keyboard 5 6 Using the Windows Logo Key Use the Windows Logo key in combination with other keys to perform certain functions available in the Windows operating system Refer to the Keyboard section to identify the Windows Logo key Windows Logo Key Displays or hides the Start menu Windows Logo Key d Displays the Desktop Windows Logo Key m Minimizes all open applications Shift Windows Logo Key m Undoes Minimize All Windows Logo Key e Launc
42. s the system is plugged into an active AC outlet You must disconnect the power cord to avoid damage to the internal components of the computer Lay the computer down on its large base for greater stability Lift up on the access panel handle 1 slide the access panel back about 1 25 cm 1 2 inch then lift it up and off the unit 2 RN XL OS IH IH Figure 2 2 Removing the Computer Access Panel CAUTION After removing the access panel look for the LED on the system board to the right of the DIMM sockets If the LED is illuminated the system still has power Turn off the computer and remove the power cord before proceeding 12 Chapter 2 Hardware Upgrades ENWW Replacing the Computer Access Panel 1 Lay the computer down on its large base for greater stability 2 Align the tabs on the access panel with the slots on the chassis and push down on the access panel while sliding it forward until it locks into place Figure 2 3 Replacing the Computer Access Panel ENWW Replacing the Computer Access Panel 13 Removing the Front Bezel 1 Remove disengage any security devices that prohibit opening the computer 2 Remove all removable media such as diskettes or compact discs from the computer 3 Turn off the computer properly through the operating system then turn off any external devices 4 Disconnect the power cord from the power outlet and disconnect any external devices CAUTION Regardless of the power
43. st one preinstalled DIMM To achieve the maximum memory support you can populate the system board with up to 8 GB of memory configured in a high performing dual channel mode DDR2 SDRAM DIMMs For proper system operation the DDR2 SDRAM DIMMs must be e _industry standard 240 pin e unbuffered PC2 4300 533 MHz compliant PC2 5300 667 MHz compliant or PC2 6400 800 MHz compliant e 1 8 volt DDR2 SDRAM DIMMs The DDR2 SDRAM DIMMs must also e support CAS latency 4 DDR2 533 MHz and DDR2 667 MHz and CAS latency 5 DDR2 667 MHz and DDR2 800 MHz e contain the mandatory JEDEC SPD information In addition the computer supports e 256Mbit 512Mbit and 1Gbit non ECC memory technologies e single sided and double sided DIMMs DIMMs constructed with x8 and x16 DDR devices DIMMs constructed with x4 SDRAM are not supported ES NOTE The system will not start if you install unsupported DIMMs ENWW Installing Additional Memory 17 Populating DIMM Sockets There are four DIMM sockets on the system board with two sockets per channel The sockets are labeled XMM1 XMM2 XMM3 and XMM4 Sockets XMM1 and XMM2 operate in memory channel A Sockets XMM3 and XMM4 operate in memory channel B Figure 2 7 DIMM Socket Locations Item Description Socket Color 1 DIMM socket XMM1 Channel A Black 2 DIMM socket XMM2 Channel A White 3 DIMM socket XMM3 Channel B White 4 DIMM socket XMM4 Channel B White The system will automatically
44. t available unpopulated SATA connector on the system board in the following order SATAO SATA1 SATA3 SATA2 34 Chapter 2 Hardware Upgrades ENWW ENWW 10 11 12 13 Replace the computer access panel Reconnect the power cord and turn on the computer Lock any security devices that were disengaged when the computer access panel was removed Reconfigure the computer if necessary Refer to the Computer Setup F10 Utility Guide on the Documentation and Diagnostics CD for instructions about using Computer Setup EX NOTE Ifyou replaced the primary hard drive use the Restore Plus CD set that you created when you initially set up the computer to restore the operating system software drivers and any software applications that were preinstalled on the computer When the restore process has completed reinstall any personal files that you backed up before replacing the hard drive Installing Additional Drives 35 Changing from a Minitower to a Desktop Configuration 1 2 3 Remove disengage any security devices that prohibit opening the computer Remove all removable media such as diskettes or compact discs from the computer Turn off the computer properly through the operating system then turn off any external devices Disconnect the power cord from the power outlet and disconnect any external devices CAUTION Regardless of the power on state voltage is always present on the system board as long as the system is
45. uch as diskettes or compact discs from the computer Turn off the computer properly through the operating system then turn off any external devices Disconnect the power cord from the power outlet and disconnect any external devices CAUTION Regardless of the power on state voltage is always present on the system board as long as the system is plugged into an active AC outlet You must disconnect the power cord to avoid damage to the internal components of the computer Remove the computer access panel CAUTION After removing the access panel look for the LED on the system board to the right of the DIMM sockets If the LED is illuminated the system still has power Turn off the computer and remove the power cord before proceeding Locate the memory module sockets on the system board A WARNING To reduce risk of personal injury from hot surfaces allow the internal system components to cool before touching Installing Additional Memory 19 7 Open both latches of the memory module socket 1 and insert the memory module into the socket 2 amp jo Figure 2 8 Installing a DIMM gt ES NOTE A memory module can be installed in only one way Match the notch on the module with the tab on the memory socket A DIMM must occupy the black XMM1 socket For maximum performance populate the sockets so that the memory capacity is spread as equally as possible between Channel A and Channel B Refer to Popul
46. ut preventing electrostatic damage refer to Appendix D Electrostatic Discharge Handle a drive carefully do not drop it Do not use excessive force when inserting a drive Avoid exposing a hard drive to liquids temperature extremes or products that have magnetic fields such as monitors or speakers If a drive must be mailed place the drive in a bubble pack mailer or other protective packaging and label the package Fragile Handle With Care Installing Additional Drives 29 30 Installing a 5 25 inch or 3 5 inch Drive into an External Drive Bay Ez NOTE A 3 5 inch drive may be a diskette drive or a media card reader A 5 25 inch drive may be an optical drive CD ROM CD R RW DVD ROM DVD R RW or CD RW DVD Combo drive or a media card reader with a 5 25 inch adapter kit attached 1 Remove disengage any security devices that prohibit opening the computer Remove all removable media such as diskettes or compact discs from the computer Turn off the computer properly through the operating system then turn off any external devices e Disconnect the power cord from the power outlet and disconnect any external devices A CAUTION Regardless of the power on state voltage is always present on the system board as long as the system is plugged into an active AC outlet You must disconnect the power cord to avoid damage to the internal components of the computer 5 Remove the computer access panel CAU
Download Pdf Manuals
Related Search