Transcend 8GB FlashDisk IDE 1" MLC
Contents
1. Form Factor 1 inch HDD Storage Capacities 2 GB to 8 GB Length 30 0 0 0 20 Dimensions mm Width 40 00 0 30 Height 3 50 0 50 Weight 6g Environmental Specifications Operating Temperature 0 c to 70 c Storage Temperature 40 c to 85 c Reliability Write Erase Endurance gt 2 000 000 cycles Read Endurance Unlimited Data Reliability Built in 4 symbol correction ECC per 512 bytes Sector Connector Durability 10 000 times Note Base on SLC Flash Interface Specification Jumper Settings No Jumper Setting Default Master mode Drivers No Device Driver Required ATA Compatibility ATA ATAPI 5 PIO Modes 0 6 Ultra DMA Modes 0 4 Note There is no IOCS16 signal support and all Data Transfer is 16 bits in width Compliance and Warranty Compliance CE FCC and BSMI Warranty 2 years Transcend Information Inc Rev 1 0 TS2GIFD10 TS4GIFD10 TS8GIFD10 TS2GIFD10M TS4GIFD10M TS8GIFD10M 1 IDE FLASH DISK Pin Assignments GND DD10 DD9 DD2 DD8 DD1 PDIAG CBLID DDO DASP DAO DMACK DA1 DMARQ DA2 IORDY DDMARDY DSTROBE RESET CSEL VCC VCC INTRQ DIOW STOP DIOR HDMARDY HSTROBE CS1 CS0 DD15 DD7 DD14 DD6 DD13 DD5 DD12 DD4 DD11 DD3 GND Transcend Information Inc 3 Rev 1 0 TS2GIFD10 TS4GIFD10 TS8GIFD10 TS2G2. Transcend Information Inc Rev 1 0
3. 1 When this pin is grounded this device is configured as Default Not support Device 0 When this pin is High this device is configured as Device 1 INTRQ Interrupt When this device is selected this signal is the active high Interrupt Request to the host VCC Power supply GND Ground T An input from the host system to the device O An output from the device to the host system 1 0 An input output bi direction common P Power supply Transcend Information Inc 5 Rev 1 0 TS2GIFD10 TS4GIFD10 TS8GIFD10 TS2GIFD10M TS4GIFD10M TS8GIFD10M 1 IDE FLASH DISK Block Diagram D00 D07 CEO Others CE1 Flash Disk Controller D10 D17 CE1 CE3 Data bus Control Signal IDE Co a V Z m U O Q 2 2 D Q Q Flash Memory WE RE Flash Memory DO D7 CEO CE1 WE RE DC Characteristics Symbol Description Min Max Units lot Driver sink current 4 mA loLDASP Driver sink current for DASP 12 mA lou Driver source current 400 uA loHDMARQ Driver source current for DMARQ 500 uA Iz Device pull up current on DD 15 0 and 10 200 uA STROBE when released Vin Voltage input high 2 0 5 5 V Vi Voltage input low 0 8 V Von Voltage output high at lon min 2 4 V VoL Voltage output low at lo min 0 5 V AC Characteristics Symbol Description Min Max Units Sr
4. Address Mode supported Y Set up Not set up C The register contains command specific data Transcend Information Inc 7 Rev 1 0 TS2GIFD10 TS4GIFD10 TS8GIFD10 TS2GIFD10M TS4GIFD10M TS8GIFD10M 1 IDE FLASH DISK Ordering Information TS XG IFD 10 M Duc Form Factor 1021 18 1 8 25 2 5 Capacity IDE Flash Disk 2 GB up to 8 GB Transcend Product The above technical information is based on industry standard data and has been tested to be reliable However Transcend makes no warranty either expressed or implied as to its accuracy and assumes no liability in connection with the use of this product Transcend reserves the right to make changes to the specifications at any time without prior notice USA Los Angeles E mail sales transcendusa com Maryland E mail sales_md transcendusa com www transcendusa com Exceeding Your Expectations CHINA E mail sales transcendchina com www transcendchina com TAI WAN GERMANY No 70 XingZhong Rd NeiHu Dist Taipei Taiwan R O C E mail vertrieb transcend de TEL 886 2 2792 8000 Fax 886 2 2793 2222 E mail sales transcend com tw www transcend com tw www transcend de HONG KONG E mail sales transcend com hk www transcendchina com JAPAN E mail sales transcend co jp www transcend jp THE NETHERLANDS E mail sales transcend nl www transcend nl United Kingdom E mail sales transcend uk com www transcend uk com
5. IFD10M TS4GIFD10M TS8GIFD10M 1 IDE FLASH DISK Pin Description CSO CS1 Chip select Description These signals are used to select the Command Block and Control Block registers When DMACK is asserted CS0 and CS1 shall be negated and transfers shall be 16 bits wide 10 12 14 DAO DA2 Device Address DASP Device active This is the 3 bit binary coded Address Bus The device asserts this signal when active The device will not be Device 1 During the reset protocol the device will not assert this signal DDO DD15 Device Data These signals are 16 bits bi direction Data Bus between the host and the device The DD 7 0 are used for 8 bit register transfers and ECC access DIOR I O Read This is the strobe signal used by the host to read device registers or the Data port HDMARDY UDMA ready This is a flow control signal for Ultra DMA data in bursts This signal is asserted by the host to indicate that the host is ready to receive Ultra DMA data in bursts The host may negate HDMARDY to pause an Ultra DMA data in burst HSTROBE UDMA Strobe This is the data out strobe signal from the host for an Ultra DMA data out burst Both the rising and falling edge of HSTROBE latch the data from DD 15 0 into the device The host may stop generating HSTROBE edges to pause an Ultra DMA data out burst DIOW Device I O Write This is the strobe signal asserted by t
6. TS2GIFD10 TS4GIFD10 TS8GIFD10 TS2GIFD10M TS4GIFD10M TS8GIFD10M 1 IDE FLASH DISK Description The 1 inch IDE Flash Disk is small in size has a huge capacity and low power consumption making it perfect for use as a mobile storage solution in devices such as Mobile Phones PDA and GPS systems This guide is written to provide general installation and handling information please use it in conjunction with the Owner s Manual for your device or system Placement es IIT a 1 RIRRARNARIREARRRRARARRA POWER g E E LIO P ARIRRARNARAREARARRARARRA BARRAGEHARAABARAARARAAAA ARARRARNARAAFARARBARARRA E ee ae TRETEN Features RoHS compliant Fully compatible with 1 0 inch hard drive form factor and interface Non volatile Flash Memory for outstanding data retention Built in ECC Error Correction Code functionality and wear leveling algorithm ensures highly reliable of data transfer Supports up to PIO Mode 6 and Ultra DMA Mode 4 LED indicates usage status Power and Data Access Lower Power Consumption Shock resistance Dimensions Side Millimeters Inches A 40 00 0 30 1 575 0 012 B 30 00 0 20 1 181 0 008 C 3 50 0 50 0 138 0 020 Transcend Information Inc Rev 1 0 TS2GIFD10 TS4GIFD10 TS8GIFD10 TS2GIFD10M TS4GIFD10M TS8GIFD10M 1 IDE FLASH DISK Specifications Physical Specification
7. he host to write to the device register or the Data port STOP Stop UDMA Burst DMACK DMA acknowledge DMARQ DMA Request This signal shall be negated by the host prior to initiation of an Ultra DMA burst Assertion of STOP by the host during an Ultra DMA burst signals the termination of the Ultra DMA burst This signal is used by the host in response to DMARQ to initiate DMA transfer For DMA data transfers Device will assert DMARQ when the device is ready to transfer data to or from the host PDIAG Pass diagnostics Optional signal The device will only be a Device 0 This signal may be asserted by Device 1 to indicate to Device O that Device 1 has completed diagnostics Leave disconnected if not used Transcend Information Inc Hardware reset signal from the host Rev 1 0 TS2GIFD10 TS4GIFD10 TS8GIFD10 TS2GIFD10M TSAGIFD10M TS8GIFD10M 1 IDE FLASH DISK IORDY I O channel ready This signal is used to temporarily stop the host register access read or write when the device is not ready to respond to a data transfer request DDMARDY UDMA ready The device will assert this signal to indicate that the device is ready to receive Ultra DMA data out burst DSTROBE UDMA data When Ultra DMA mode DMA Read is active this signal is the strobe data in strobe generated by the device CSEL Cable select This pin is used to configure this device as Device 0 or Device
8. ise Rising edge slew rate for any signal 1 25 V ns SraLL Falling edge slew rate for any signal 1 25 V ns Chost Host interface signal capacitance at the 25 pf host connector Caevice Device interface signal capacitance at 20 pf the device connector Transcend Information Inc 6 Rev 1 0 TS2GIFD10 TS4GIFD10 TS8GIFD10 TS2GIFD10M TSAGIFD10M TS8GIFD10M 1 IDE FLASH DISK Command Set The following table summarizes the command defined in the ATAPI 5 specification and lists the commands supported by the TS2 4 8GIFD10 No commandset code FR sc sw cy pR HO LBA ER Lupo alee d E ES ed Y Code 9 crATanset Seco demn v lv viv v v 4 CFA Write Multiple wo Erase fcon f y vy y y y y 5_ICFAWrite Sector wo Erase e v v v v v v 6_ Check Power mode JE J v Execute Device Diagnostic o v Identify Device n J v I 9 fiae Exc spy e psu Idie immediate Eth v Initialize Device Parameters 91h NOP 0h Read Buffer Eh Read DMA CB Read Multiple Read Sector s 20h Read Verify Sectors 40h leep S w 27 write Sector ko PV PV Tv Tv ty vy Note 1 FR Feature Register SC Sector Count Register SN Sector Number Register CY Cylinder Low High Register DR Drive bit of Drive Head Register HD Head No bitO bit3 of Drive Head Register LBA Logical Block
Download Pdf Manuals
Related Search