British Telecom 036261 telephone
Contents
1. User Guide aw eng ty bh K priimti p S hr T amf WR yp uv i f LL O ueil Apert L fi TE Mt uit d Me Welcome to your BT Converse 1200 Corded Telephone Ten one touch buttons for easy dialling of stored numbers Five buttons are pre set to useful BT Calling Features which you can change Headset facility lets you make and receive calls privately while keeping your hands free Handsfree lets you make and receive calls using the built in loudspeaker Secrecy lets you talk to someone else close by without your caller hearing Adjust the volume of your caller s voice Last number redial Providing you are connected to a compatible switchboard or are a 1571 user the voice mail indicator lets you know if you have messages on your network s answering service Data port lets you connect a modem or similar products Hearing aid friendly WW The BT Converse 1200 is fitted with an inductive coupler so it is compatible with hearing aids Location You need to place your BT Converse 1200 within 3 metres of a telephone socket so that the cable will reach Your BT Converse 1200 can be wall mounted see Wall mounting your phone on page 13 WARNING Do not place your BT Converse 1200 in the bathroom or other humid areas Setting up Insert 3 x AA batteries Turn the phone over and remove the battery compartment cover Insert the batteries and replace the cover The batteries are r2. the 1571 one touch button to connect to your answering service Message waiting switch Your Converse 1100 is preset to work with BT1571 on normal exchange lines If your telephone is connected to a switchboard you may need to change the switch hn setting on the base of the phone Try it on setting 1571 vw but if it doesn t work try the other settings R Typically position MW1 is for an ISDX type switch but if the light stays on permanently use MW2 Typically position MW3 is for an SX 2000 type switch Adjusting the ringer volume Ringer Volume Set the Ringer Volume switch on the underside of the phone to O Off 1 or 2 Using the phone Adjusting the ringer tone Ringer Set the Ringer switch on the underside of the phone to 1 Low 2 Medium or 3 High Recall The Ee button is used to access a range of switchboard services for example to transfer calls and with some BT Calling Features One touch memory buttons You can store your 10 most frequently used numbers in the memory and dial them by pressing a single button Each number can be up to 28 digits long The number can include a Pause see below or The bottom 5 one touch memory buttons have been pre set to dial BT Calling Features see following page If required you can over write these simply by storing your preferred phone numbers on these buttons To re instate the pre set numbers see page 10 Store a one tou
3. 0 is connected to a switchboard you can simply use it as a normal extension If you are not connected to the BT network some of these services may not be available Please contact your Network Provider 118500 118707 Calls BT s residential or business directory enguiry service BT Answer 1571 Calls your network s answering service for example BT Answer 1571 to access any voicemail messages you may have Details on using the service are provided when you subscribe Call Divert You can divert all incoming calls to another number of your choice Please note Call Diversion services may allow other divert options Check with your network provider for details Switch Call Diversion on Lift the handset press the Call Diversion On one touch memory button button 9 10 Using BT Calling Features Enter the number you want calls diverted to then press and listen for confirmation of your instructions Replace the handset Switch Call Diversion off Lift the handset press the Call Diversion Off one touch memory button button 10 Replace the handset For further information see the BT Calling Features User Guide supplied when you subscribe to the services of your choice Re instate the pre set BT Calling Features numbers If you overwrite the pre set numbers stored on the one touch buttons you can re instate the original numbers at any time Lift the handset or press a or B Press the
4. 1 Press Q You will hear the dial tone 2 Dial the number you want When your call is answered speak as normal Press ag to end the call e Transferring the call to the handset or a headset During a conversation if you want to keep it private you can transfer the call from handsfree to the handset by lifting the handset or to the headset by pressing dD Receive a call handsfree 1 When the phone rings press ee and speak Using the phone Change the volume of the caller s voice During a call whether using the handset a headset or using handsfree you can adjust the volume of your caller s voice During a call press eg or to adjust the volume Redialling the last number The redial number can up to 32 digits long Lift the handset or press Gy or a then press Secrecy During a call you can talk to someone nearby without your caller hearing you Press ee The red secrecy light comes on and your caller cannot hear you Press R again to return to your caller Message waiting If you subscribe to your network s answering service for example BT 1571 and you have new voicemail messages the message waiting indicator will flash IMPORTANT You will need to fit batteries see page 3 to use the message waiting feature if your BT Converse 1200 is connected to a switchboard message waiting will only work with compatible models Lift handset or press ag or Pp and dial 1571 or press
5. ch memory number Please note that the D button is located underneath the memory label Press then the one touch button you want to use Enter the telephone number you want to store and press again The number is now stored Dial a one touch memory number Lift the handset or press eg or a then press the one touch button you want The stored number is dialled Change a one touch memory number To change a one touch number simply overwrite the current number by storing a new one Storing a pause in a number A pause is normally inserted in a stored telephone number after a switchboard access code e g 9 to allow the switchboard time to get an outside line before the number is dialled For example 9 Pause 08702405522 To enter a pause press in the appropriate place when storing the number Your BT Converse 1200 gives you easy access to a range of BT Calling Features The bottom 5 one touch memory buttons have been preset with the following services One touch button Service Number 6 Directory Eng s residential 118500 7 Directory Eng s business 118707 8 BT Answer 1571 1571 9 Call Divert On 21 10 Call Divert Off 21 Please note You can overwrite any pre set numbers with your own numbers by following the instructions on page 10 Compatibility and availability of services A switchboard can provide a similar range of functions to BT Calling Features If your BT Converse 120
6. cts please call 0870 240 5522 or visit www withandwithoutwires com WithoutWires com Technical information How many telephones can you have e All items of telephone equipment have a Ringer Equivalence Number REN which is used to calculate the number of items which may be connected to any one telephone line Your BT Converse 1200 has a REN of 1 A total REN of 4 is allowed If the total REN of 4 is exceeded the telephone may not ring e With different telephone types there is not guarantee of ringing even when the REN is less than 4 13 General information Switchboard compatibility This product is intended for use within the UK for connection to public telephone network and compatible switchboards which support tone dialling and timed break recall If in doubt please consult your service provider R amp TTE Directive Hereby TMX declares that this BT Converse 1200 is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC A copy of the Declaration of Conformance for the BT Converse 1200 is available from TMX Alpha Business Park 28 White House Road Ipswich IP1 5LT Wall mounting your phone e WARNING Before you wall mount your BT Converse 1200 check that you are not drilling into any hidden wiring or pipes 1 Unclip the stand from the base of the phone and remove it Re route the telephone line cord towards the bottom of the phone 2 Drill two holes i
7. e sequence flash flash off repeatedly Message waiting indicator Flashes when you have voice mail page 7 Store under memory label Use to store one touch memory numbers page 8 One touch memory buttons Press a one touch button to dial the stored number page 8 Buttons 6 10 are pre set to dial BT Calling Features page 9 Secrecy button amp indicator During a call press to stop your caller hearing you so you can talk privately to someone else close by page 7 Headset button amp indicator Lets you make and receive calls with a headset page 6 Redial Redials the last number called page 7 Also used to enter a pause in a stored number page 8 Making and ending calls Lift the handset and dial the number you want Replace the handset to end the call Using a headset Headsets are not supplied with your BT Converse 1200 However you can purchase headsets with RJ11 jack by calling 0870 240 5522 or by visiting www withandwithoutwires com Make a headset call Plug the headset not supplied into the socket marked HEADSET on the underside of the base Press D and dial the number When the headset is in use the headset indicator on the D button will be lit Press B to end the call Receive a headset call When the phone rings and the headset is plugged in press p to answer Handsfree Make and receive calls without lifting the handset Make a handsfree call
8. equired as a back up power source in case the phone is disconnected from the phone line and are also needed for the message waiting feature to work If this happens and you have not installed back up batteries any numbers you have stored in the memory will be saved for only 5 minutes The pre stored one touch numbers will not be affected Battery low indicator When the batteries are low the light will flash with the seguence flash flash off repeatedly Check the dial mode setting The Mode switch on the underside of your BT Converse 1200 should be set to TB for tone dialling If your phone does not work try setting the dialling mode to P or T Your BT Converse 1200 has a data port so you can connect another product such as a modem If required connect the device to the DATA port on the side of the phone Data cable Your BT Converse 1200 is now ready for use Handset park If the phone is wall mounted you can hang the handset here if you need to leave the phone For use with a switchboard and some BT Calling Features page 9 Handsfree button amp indicator Make and receive calls handsfree via the built in loudspeaker page 6 Volume O S OO oy DOGOS cUm Volume Adjust the volume of your caller s voice page 7 Call Battery low indicator Flashes when you have an incoming call When the batteries are low the light will flash with th
9. n the one touch button you want to re set Press and replace the handset or press GF or B Safety Clean the phone with a damp not wet cloth or an anti static wipe Never use household polish as this will damage the product Never use a dry cloth as this may cause a static shock Do not open the handset or base This could expose you to high voltages or other risks Do not submerge any part of your product in water and do not use it in damp conditions such as bathrooms Do not expose your product to fire explosive or other hazardous conditions Never dispose of batteries in a fire There is a serious risk of explosion and or the release of highly toxic chemicals Do not expose to direct sunlight Do not stand your product on carpets or other surfaces which generate fibres or place it in locations preventing the free flow of air over its surfaces Guarantee For your records Date of purchase Place of purchase Serial number For guarantee purposes proof of purchase is reguired so please keep your receipt Your BT Converse 1200 is guaranteed for a period of 12 months from the date of purchase Subject to the terms listed below the guarantee will provide for the repair of or at BT s or its agent s discretion the option to replace the BT Converse 1200 or any component thereof which is identified as faulty or below standard or as a result of inferior workmanship of materials Products over 28 days old f
10. n the wall 75 80mm vertically apart using an 8mm drill bit 3 Insert the wall plugs if necessary then insert the screws leaving about 5mm protruding from the wall on which to hang the phone 4 Rotate the handset hook 180 so that it sticks upwards This holds the handset in place when wall mounted a gt go ra 7 Slot the holes on the back of the base over the screw heads and gently pull the phone down to fix it securely in place e Using the handset park when the phone is wall mounted If you need to leave the phone whilst on a call Mr hang the handset on the handset park at the sp top left hand side of the base a BT Conver Visit us at www bt com Offices worldwide The telecommunications services described in this publication are subject to availability and may be modified from time to time Services and eguipment are provided subject to British Telecommunications plc s respective standard conditions of contract Nothing in this publication forms any part of any contract 9 British Telecommunications plc 2004 Registered Office 81 Newgate Street London EC1A 7AJ Registered in England No 1800000 BT Converse 1200 07 04 6 Designed and produced by The Art amp Design Partnership Ltd C Printed in China
11. rom the date of purchase may be replaced with a refurbished or repaired product The conditions of this guarantee are The guarantee shall only apply to defects that occur within the 12 month guarantee period Proof of purchase is reguired The eguipment is returned to BT or its agent as instructed This guarantee does not cover any faults or defects caused by accidents misuse fair wear and tear neglect tampering with 12 General information the equipment or any attempt at adjustment or repair other than through approved agents e This guarantee does not affect your statutory rights Within the 12 month guarantee period e Inthe unlikely event of a defect occurring please return the product with the receipt to the place of purchase Outside of the 12 month guarantee period If your product needs repair after the guarantee period has ended the repair must meet the approval requirements for connection to the telephone network We recommend that you contact BT s approved repair agent TecLogic on 08702 405029 or a local qualified repairer Returning your phone Where possible pack the product in its original packaging Please remember to include all parts including the line cords Please note that we cannot take responsibility for goods damaged in transit Please obtain and keep proof of posting from the carrier Accessories and replacement items For a full range of accessories and replacement items for BT produ
Download Pdf Manuals
Related Search