Nortel Ethernet Switch 470-24T-PWR
Contents
1. 7 32kg 16 14lb e Height 4 37cm 1 73in e Width 43 82cm 17 25in e Depth ES 470 35 31cm 13 9in ES 470 PWR 38 20cm 15 05in Safety agency approvals e International IEC 60950 e Europe EN 60950 e US UL60950 e Australia New Zealand AS NZS 60950 e Canada CSA22 2 60950 e Mexico NOM Environmental specifications e Operating temperature 0 to 40 C 32 to 104 F e Storage temperature ES 470 25 to 55 C 13 to 131 F ES 470 PWR 25 to 70 C 13 to 158 F e Operating humidity 85 maximum relative humidity non condensing e Storage humidity 95 maximum relative humidity non condensing e Operating altitude Up to 3 024 m 10 000 ft above sea level e Storage altitude Up to 12 096 m 40 000 ft above sea level Electromagnetic Emissions and Immunity Meets the following standards e US FCC CFR47 Part 15 Subpart B Class A e Canada ICES 003 Class A CISPR 22 Class A CISPR 24 e Europe EN55022 Class A EN55024 1998 e Australia New Zealand AS NZS 3548 Class A e Japan VCCI V 3 02 04 Class A e Korea MIC No 2001 116 e Taiwan CNS 13438 Class A Ordering information Chassis Order No Description AL2012 52 E5 Ethernet Switch 470 48T PWR with 48 10 100 IEEE 802 3af Power over Ethernet ports and 2 built in GBIC slots plus built in stacking ports and RPSU connector 45cm 18in stacking cable included Ethernet Switch 470 24T PWR w2. for order numbers The Ethernet Switch 470 also requires a DC to DC converter New Ethernet Switch software features The Ethernet Switch Software Release 3 6 2 for Ethernet Switch 470 supports these new features VLACP Messages This feature generates a system log and SNMP trap messages when Virtual Link Aggregation Control Protocol VLACP enables or disables a link This enables administrators to determine the status of links configured with VLACP for health checking STP BPDU Filtering This release supports the BPDU Filtering feature for Spanning Tree Protocol Based on the BPDU information exchange selection of a root bridge occurs Typically when a new bridge joins the spanning tree or an existing bridge leaves the spanning tree the root selection process is repeated and a new root is selected if appropriate The BPDU Filtering feature allows the network administrator to block an unwanted root selection process when an edge device is added to the network This prevents unknown devices from influencing an existing spanning tree topology When a port has BPDU Filtering enabled and it receives an STP BPDU the port is immediately put in the operational disabled state A trap message is generated and a message is written to the switch log The port stays in the operational disabled state until the port timer expires this timer is configurable by the switch administrator Web based Management for RS
3. Ethernet Switch 460 The single image software simplifies network operations and provides the flexibility of stacking different switches in the same stack Loading the image to different switches is also considerably simplified The image is loaded only to the base unit of the stack which automatically loads it to other switches in the stack Advanced Management The Enterprise Switch Manager ESM performs configuration functions such as VLAN assignments MLT and Multicast across multiple Nortel Ethernet switches Business level policies are enforced auto matically across the network using the Enterprise Policy Manager EPM soft ware his software provides centralized control of advanced packet classification and the ability to priority mark police meter or block traffic With the Enterprise Network Management System ENMS the network manager has quick access to the information required to manage and isolate all network events on the 470 switches BootP and TFTP support allows centralized switch IP address assign ment software upgrades and SNMP agent updates over the network The RADIUS based security feature uses the RADIUS Remote Authentication Dial In User Services protocol to authenti cate local console and TELNET logins Command Line Interface CLI The CLI is used to automate general management and configuration of the Ethernet Switch 470 The CLI may be used through a Telnet Secure Shell session or
4. a connected device is operating at 10 Mbps or 100 Mbps and automat ically adjust to the optimal speed Figure 4 Nortel Ethernet Routing Switch 470 PWR Network diagram Secure Router Internet Frame Relay DSL or Cable Modem IPv4 IPv6 MPLS ZZ ZE AE AE A AE A SR E T1 E1 Digital Trunk or Analog Trunks Converged LAN f sanning E 7 am ER Network BCM 200 Si Manager RE Zei ES 470 PWR ER e s no ress ere r Py l Ss Lu f ES 470 PWR fe e xX e qa G Ke ch 28 Se i J Stacking Edge 10 100 PoE 1 Gig E Fiber Stacking Edge Custom Autonegotiation Advertisements CANA This feature enables the network manager to tune the capabilities that a particular Ethernet port can advertise via autonegotiation The capabilities include half duplex and full duplex modes with speeds of 10 or 100 Mbps Autonegotiated Ethernet ports establish a connection based upon the highest common capabilities This feature saves the network manager from having to go to each workstation and switch to configure a fixed speed Auto MDI MDIX The Ethernet Switch 470 can be connected to other switches or devices using either a straight through or a crossover cable When a cable is connected to one of the 10 100 ports on the switch the switch port automatically can detect the energy on the cable and configures itself accordingly This feature makes co
5. Ethernet Switch 470 family Converged edge gt Desktop connectivity gt Power over Ethernet gt IP Telephony gt Wireless LAN Key features gt High speed desktop switching gt Power over Ethernet gt Resilient Stacking gt Distributed Multi Link Trunking gt Quality of Service gt Security features gt Advanced management Se i sessaaaa seeaaans SESESESE i SEESEEE SSES ssssssss t y e eem Se Sesgesggeg SESSEEES EEN En WEE E EL la a saseasess see RE wg EE Sr semsse VUVETTET es Ethernet Switch 470 stack The Nortel Ethernet Switch 470 product family is a stackable solution that provides resiliency security and conver gence readiness required by today s application and competition driven enterprise networks The Ethernet Switch 470 family delivers Layer 2 switching with Power over Ethernet models for simplified network deploy ments to help drive lower Total Cost of Ownership The Ethernet Switch 470 is available in four models the Ethernet Switch 470 24T with 24 10 100 ports plus two Gigabit Interface Converters GBICs ports the Ethernet Switch 470 48T Ethernet Switch 470 24T PWR Ethernet Switch 470 48T PWR with 48 10 100 ports and two GBICs the Ethernet Switch 470 24T PWR with 24 10 100 ports supporting Power over Ethernet plus two GBICs and the Ethernet Switch 470 48T with 48 10 100 ports supporting Power over Ethernet and two GBIC
6. FTP REC 791 IP e RFC 792 ICMP RFC 793 TCP e RFC 826 ARP e RFC 854 Telnet RFC 894 IP over Ethernet RFC 951 BootP RFC 1112 IGMPv1 RFC 1157 SNMP RFC 1213 MIB II RFC 1271 RMON RFC 1493 Bridge MIB RFC 1573 IF MIB RFC 1757 RMON RFC 1945 HTTP v1 0 RFC 2030 Simple NTP RFC 2138 RADIUS RFC 2236 IGMPv2 RFC 2570 SNMPv3 RFC 2571 SNMP Frameworks RFC 2572 SNMP Message Processing RFC 2573 SNMPv3 Applications RFC 2574 SNMPv3 USM RFC 2575 SNMPv3 VACM RFC 2576 SNMPv3 RFC 2665 Ethernet MIB RFC 2674 Q MIB RFC 2737 Entity MIBv2 REC 2748 COPS RFC 2819 RMON MIB RFC 2863 Interfaces Group MIB RFC 2940 COPS Clients RFC 3084 COPS Provisioning 470 Power over Ethernet specifications e 802 3af compliant with Power classifica tion support e Signal pair power delivery e Maximum 15 4w per port e Maximum DTE Power AC only 370w e Maximum DTE Power AC RPSU 740w LED indicators e Per port status LEDs 10 or 100 Mbps port speed Power over Ethernet detection link status e System status LEDs Power system RPSU stack mode base mode Electrical specifications e Power supply AC 100 240V 50 60Hz e Input current at 110v 0 37A 470 5 45A 470 PWR e Input current at 220v 0 18A 470 2 73A 470 PWR e Max power consumption 90W 470 600w 470 PWR Physical specifications e Weight ES 470 24 T 4 8kg 10 56lb 48 T 5 0kg 11 0lb ES 470 PWR no PC 24 T 7 14kg 15 74lb 48 T
7. TP MSTP and LACP This release provides Web based manage ment support for Rapid Spanning Tree Protocol IEEE 802 1w Multiple Spanning Tree Protocol IEEE 802 1s and Link Aggregation Control Protocol LACP IEEE 802 3ad MLT Shutdown Ports on Disable The MLT shutdown ports on disable feature is used to prevent broadcast storms when an MLT is disabled and some or all of its ports are still connected to another device The feature enabled all ports that are members of the MLT to be automati cally shut down when the MLT is disabled and then generates a trap message When enabling an MLT group then any disabled ports are enabled automatically when this feature is enabled This feature is user config urable and is disabled by default so that the default behavior remains the same as previous releases Lifetime warranty All Ethernet Switch 470 models offer a lifetime warranty Enterprises demand quality products and companies that stand behind them A Nortel product hardware warranty is supported for as long as the original end user continues to own or use the product including fan and power supply In the event of a discontinuance of product manufacture the Nortel warranty support is limited to five 5 years from the announcement of discontinuance Summary With more than 100 years in telecom munications Nortel is uniquely posi tioned to help your business reduce cost on a vendor that only understands part o
8. atts of power This solution will provide 15 4 W per port from the Ethernet Switch 470 48T PWR Additionally the addition of an RPS15 chassis and power supply can be used to provide dual power feeds to the switch ensuring higher availability where customers require their switches connected to more than one power feed A DC connector cable is required to connect Table 1 Key differences between Nortel Ethernet Switch 470 470 PWR and 460 PWR Feature 10 100 ports Power over Ethernet Built in stacking GBIC uplinks 100Base FX uplinks Height RU Rack Unit 470 PWR 24 48 Noe 470 24 48 460 PWR 2 or 4 optional with MDA 1 5 RU from an Ethernet Switch 470 or 470 PWR to the RPS15 RPSU module see Table 2 Ordering information Figure 1 Built in stacking ports e CSN ki TS Ca Resilient Stacking Two Built in Stacking Ports Ethernet Switch 470 models have two built in stacking ports for simpler quicker and more cost effective stacking This unique stacking design frees up both of the uplink ports for dedicated connectivity to the backbone A 46cm 18 stacking cable is included with the product Figure 1 A key differentiation for the Ethernet Switch 470 family is its resilient stacking feature This switch can stack up to eight units with a resilient cascade stacking design assuring continuous uptime even if a switch in the stack should fail Figure 2 Auto Unit Re
9. er bandwidth up to 8 Gbps with active redundant links in one trunk Up to six trunks are supported per switch or stack The resilient trunking features DMLT and MLT of the Ethernet Switch 470 can be combined with the SMLT feature of 8600 8300 5500 or 1600 switches in a cluster configuration providing a self healing network which delivers maximum reliability and avail ability Figure 4 Multiple connections to the network core allow customers to double their network bandwidth with no extra investment as all ports are active in SMUT configuration 802 3ad Link Aggregation IEEE 802 3ad provides an industry standard method for bundling multiple links together to form a single trunk between two networking devices Both Dynamic Link Aggregation Group LAG trunks and MLT trunks are supported Once configured the Link Aggregation Group or trunk group is managed by the Link Aggregation Control Protocol LACP When one of the active links goes down the standby link becomes active Virtual Link Aggregation Control Protocol VLACP VLACP is a Nortel extension of the Link Aggregation Control Protocol to provide a Layer 2 handshaking protocol which can detect end to end failure between two physical Ethernet inter faces It allows the switch to detect uni directional or bi directional link failures irrespective of intermediary devices and enables significant improvements in network fail over times Spanning Tree Protoco
10. er multiple vendors devices The switch can supply power up to 15 4 Watts per port which meets the IEEE 802 3af standard Dynamic power management Each port on the Ethernet Switch 470 PWR can be configured to limit the power delivered to a device Each port can also be configured for power priority level low high and critical On the switch total available power is monitored In the case where all avail able power is fully utilized the switch may turn off lower priority ports and turn on higher priority ports The Ethernet Switch 470 PWR can automatically disable a port if there is a short All other ports on the switch will remain active and will not be affected by the disabled port Plug n play IP Telephony switching Automatic Discovery and Automatic Configuration ADAC capability enables the switch to detect Nortel IP Phones and automatically configure the port and QoS parameters The Ethernet Switch 470 PWR provides simplified Java Device Manager and Web based configurations on data and power prop erties These graphical user interfaces make it simple to set up data and power configurations Load sharing and redundant power for 470 PWR Ethernet Switch 470 24T PWR or 470 48T PWR provides up to 370 watts of DTE power for Power over Ethernet devices With the addition of a Redun dant Power Supply RPS15 chassis and the 600 watt RPS15 power module the Ethernet Switch 470 48T PWR can support up to 740 w
11. f the equation Let us show you how the Ethernet Switch 470 family along with other Nortel products can increase your profitability streamline your busi ness operations increase productivity and help you gain the competitive edge Technical specifications Interfaces ES 470 e 24 48 port 10 100 Base T e 2 port 1000 Base GBIC ES 470 PWR e 24 48 port 10 100 Base T with 802 3af Power over Ethernet e 2 port 1000 Base GBIC Performance specifications e Switch fabric bandwidth 2 56 Gbps e Frame length 64 to 1518 bytes IEEE 802 1Q Untagged 64 to 1522 bytes IEEE 802 1Q Tagged e Multi Link Trunks Up to 6 trunks with 4 links per group e VLANs Up to 256 per switch e Multiple spanning tree groups Up to 16 STGs e Distributed Multi Link Trunking Network protocol and standards compatibility IEEE 802 1D Spanning Tree Protocol IEEE 802 1p Prioritizing IEEE 802 1Q VLAN tagging IEEE 802 1s Multiple Spanning Tree Groups IEEE 802 1w Rapid Spanning Tree IEEE 802 1x Ethernet Authentication Protocol IEEE 802 3 10Base T ISO IEC 8802 3 Clause 14 IEEE 802 3 Auto negotiation IEEE 802 3ad Static dynamic LACP IEEE 802 3af Power over Ethernet 470 PWR only IEEE 802 3u 100Base TX ISO IEC 8802 3 Clause 25 IEEE 802 3u Autosensing ISO IEC 8802 3 Clause 28 IEEE 802 3x Flow control on the Gigabit uplink port IEEE 802 3z Gigabit Ethernet IETF DiffServ RFC support e RFC 768 UDP e RFC 783 T
12. human experience ignite and power global commerce and secure and protect the world s most critical information Our next generation technologies for both service providers and enterprises span access and core networks support multimedia and business critical applications and help eliminate today s barriers to efficiency speed and performance by simplifying networks and connecting people with infor mation Nortel does business in more than 150 countries For more information visit Nortel on the Web at www nortel com For more information contact your Nortel representative or call 1 800 4 NORTEL or 1 800 466 7835 from anywhere in North America Nortel the Nortel logo Nortel Business Made Simple and the Globemark are trade marks of Nortel Networks All other trademarks are the property of their owners Copyright 2006 Nortel Networks All rights reserved Information in this docu ment is subject to change without notice Nortel assumes no responsibility for any errors that may appear in this document LUT AT AEE AAA A HIRTT NN100100 111306 NORTEL gt BUSINESS MADE SIMPLE
13. istributed Access List Security feature network access is granted or denied on a per port basis The Ethernet Switch 470 also provides RADIUS authentication for switch security management EAPOL Security Enhancements EAP Extensible Authentication Protocol now supports two modes for authentication e Single Host with Single Authentication SHSA and Guest VLANs e Multiple Host MAC with Multiple Authentication MHMA EAP Clients only SHSA allows only one device user on that port to complete EAP Authentication With MHMA multiple devices each with a different MAC address are allowed on a port Each device must complete EAP Authentication for the port to allow traffic with the correspon ding MAC address This feature saves ports on the Power over Ethernet switch For example a laptop can be connected to an IP phone which in turn is connected to the switch and draws power from it Figure 4 MAC Addresses The Ethernet Switch 470 supports up to 16 000 MAC addresses per switch or stack for deployment of large scale enterprise networks with many attached devices and workgroups allowing for scalability and cost effectiveness VLAN support Up to 256 port based VLANs can be configured per individual switch or per stack to extend the broadcast domain and segment network traffic The 256 VLANs can be spread among port based and MAC source address based VLANs Protocol based VLANs allow switch ports to be as
14. ith 24 10 100 IEEE 802 3af Power over Ethernet ports and 2 built in GBIC slots plus built in stacking ports and RPSU connector 45cm 18in stacking cable included Ethernet Switch 470 48T with 48 10 100BaseTX ports and 2 GBIC slots plus built in stacking ports 45cm 18in stacking cable included and RPSU slot Ethernet Switch 470 24T with 24 10 100BaseTX ports and 2 GBIC slots plus built in stacking ports 45cm 18in stacking cable included and RPSU slot AL2012 53 E5 AL2012 34 E5 AL2012 37 E5 Cables and GBICs Order No Description AL2018001 E6 Ethernet Switch 400 SRC Cascade Return Cable 1 meter AL2018002 E6 Ethernet Switch 400 SSC Spare Cascade Cable 18 inch AL2018004 E6 Ethernet Switch 400 SRC Cascade Return Cable 3 meter AL2011013 E6 Console cable for use with Ethernet Switches and Ethernet Routing Switches AA1419001 E5 1 port 1OOOBase SX Gigabit Interface Connector GBIC 275M 500M MM 1 port 1OOOBase LX Gigabit Interface Connector GBIC 500M MM 5KM SM 1 port 1000Base XD Gigabit Interface Connector GBIC 50km SM 1 port 1OOOBase ZX Gigabit Interface Connector GBIC 70km SM 1 port 1000Base T GBIC 8 pin modular connector for ES products only 1 port IOOOBaseWDM GBIC with Avalanche Photo Diode Receiver 1470nm Wavelength 1 port 1OOOBaseWDM GBIC with Avalanche Photo Diode Receiver 1490nm Wavelength 1 port IOOOBaseWDM GBIC with Avalanche Photo Diode Receiver 1510nm Waveleng
15. l Built in support for Spanning Tree Protocol IEEE 802 1D detects and eliminates logical loops in the network When multiple paths exist the switch will automatically place some ports on standby to form a network with the most efficient traffic pathways avoiding the continual looping of frames load balancing and failover protection Figure 3 Distributed Multi Link Trunking across stack for higher bandwidth and fault tolerance Ethernet Switch 470 48T Stack WEE EEHEEHE for uninterrupted access to local servers and the network center Multi Link Trunking to Ethernet Switch at the network center Ethernet Routing 8600 Switch Multiple Spanning Tree protocol groups The Ethernet Switch 470 supports Nortel s multiple spanning tree groups STGs They support a maximum of eight STGs either all in one standalone switch or across a stack Multiple STGs provide multiple data paths which can be used for load balancing and redundancy Rapid Spanning Tree Protocol Built in support for Rapid Spanning Tree Protocol IEEE 802 1w and Multiple Spanning Tree Groups IEEE 802 1s provides standards based solu tions for eliminating logical loops in the network Full Auto sensing on Every Port Every UTP port on the Ethernet Switch 470 is equipped with autosensing technology to automatically detect and support the speed and mode of a connected device The ports determine whether
16. nfiguration easier eliminating the need for a dedicated MDI MDIX port and saves the confusion of selecting the right type of patch cable Quality of Service QoS The QoS features allow you to not just utilize bandwidth more efficiently opti mizing existing network resources and capabilities but also provide packet clas sification and marking at the edge of the network simplifying the QoS deploy ment at the aggregation and core of the network By classifying prioritizing policing and marking LAN traffic networks can offer reliable connectivity and required bandwidth for mission critical applications like IP Telephony and mission critical data applications to specific groups and users and to indi vidual devices For each of these applications advanced QoS features support Internet Engi neering Task Force IETF standard DiffServ QoS architecture a packet classification based on the content of packet header fields voice video data traffic policing and remote sniffing Queuing function The Ethernet Switch 470 provides network availability for mission critical applications devices and users This is done by classifying prioritizing and marking LAN IP traffic using up to eight hardware based IP service class queues on the Gigabit uplink ports based on the following parameters e ToS DSCP marking e IP source address destination address or subnets e TCP UDP source destination port por
17. placement The Auto Unit Replacement AUR feature provides the user with the ability to retain the configuration CFG image of a unit in a stack during a unit replace ment The retained configuration image from the old unit can be restored to the new unit This feature saves time and effort required to replace a failed unit Unit Replacement Feature In the unlikely event that a switch fails in a stack the affected switch can easily be replaced without disrupting the stack This feature provides the capa bility of upgrading a new unit with the configuration of the affected unit off line before adding the new unit to the stack The configuration of the affected switch may be copied from the Trivial File Transfer Protocol TFTP server to the new switch The new switch can then be inserted into the stack without requiring a reboot of the entire stack Figure 2 In the unlikely event of a switch failure the stack integrity is maintained cascade signals loop back at point of failure Distributed Multi Link Trunking Multi Link Trunking MLT enables grouping of links between the Ethernet Switch 470 and another switch or server to provide greater bandwidth with active redundant links With Nortel s Distrib uted Multi Link Trunking DMLT feature trunked ports can span multiple units of the stack for fail safe connec tivity to mission critical servers and the network center Figure 3 This can provide great
18. s All models include built in stacking ports redun dant power support and are available in compact one Rack Unit RU high design High density desktop switching Up to eight Ethernet Switch 470 24T 470 48T 470 24T PWR or 470 48T PWR may be combined in a single stack to support up to 384 10 100 ports and managed as a single entity The Ethernet Switch 470 48T and 470 48T PWR offer additional flexibility for uplink connection as ports 47 and 48 can be configured as either 10 100Base T or GBIC The Ethernet Switch 470 24T and 470 24T PWR may utilize all 26 ports simulta neously The 2 56 Gbps cascading bandwidth on these switches offers dedi cated bandwidth between the switches without sacrificing any uplink ports The Ethernet Switch 460 24T PWR can also be stacked with Ethernet Switch 470 or 470 PWR The uplink ports can be used for connections to backbone switches such as the Ethernet Routing Switch 8600 8300 1600 or 5500 Power over Ethernet 470 PWR IEEE 802 3af compliant The Ethernet Switch 470 PWR provides IEEE 802 3af standards compliant Power over Ethernet PoE and is designed to power devices such as IP phones wireless access points network cameras security and lighting devices and access control devices badge readers The benefit of being interoperable with standards based equipment means that customers are not forced to tie them selves to any one vendor as the switch has the flexibility to pow
19. signed to a VLAN based on the protocol information within the packet These VLANs localize broadcast traffic and assure that the specified protocol type packets are sent only to the protocol based VLAN ports Shared VLAN SVL and Independent VLAN Learning IVL are supported With SVL support all VLANs in the switch share the same forwarding data base IVL allows individual VLANs to have separate forwarding databases within the switch and it allows the switch to handle duplicate MAC addresses if the addresses are in different VLANs IGMP Snooping The Ethernet Switch 470 features IP Multicast support by examining snooping all Internet Group Multicast Protocol IGMP traffic in hardware at line rate and pruning unwanted data streams from affecting network or end station performance Port Mirroring The port mirroring feature sometimes referred to as conversation steering allows the network administrator to designate a single switch port as a traffic monitor for a specified port Port mirroring copies packets flowing into a specified port and sends the replicated data to the mirrored port for in depth analysis of switched traffic patterns to troubleshoot problems and optimize network configurations Additionally an external probe device can be attached to the designated monitor port Simplified Network Operations The Ethernet Switch Software supports all four Ethernet Switch 470 models as well as the
20. t range e IEEE 802 1p priority bits e Ingress physical source port e IP Protocol ID eg TCP UDP IGMP e Ether Type eg IP IPX e IEEE 802 1Q VLAN ID User Based Policies This feature enables network services i e QoS to follow the user regardless of the PC logged into or the port connected to The switch requires a user to be authenticated using EAP and sends username password information to the RADIUS server The RADIUS server provides the user s role group attributes to the switch that allows user access to the port with the default configuration The switch then passes role group port information to the Enterprise Policy Manager that config ures the user port based on the specific policy information Security features The Ethernet Switch 470 offers the highest level of security with features including Secure Shell SSH IEEE 802 1x based security also known as Extensible Authentication Protocol EAP Simple Network Management Protocol SNMPv3 IP Manager s list MAC address based security and RADIUS authentication SSHv2 supports strong authentication and encrypted communications It allows a user to log into the switch from an SSH client and perform a secure Telnet session using CLI commands This feature is ideal for security conscious customers such as federal governments For added security the Ethernet Switch 470 supports the IEEE 802 1x based security feature EAP Based on the IEEE 802 1x s
21. tandard EAP limits access to the network based on user credentials A user is required to login to the network using a username pass word the user database is maintained on the authentication server not the switch EAP prevents network connec tivity without password authorization for added security and control in physi cally non secure areas It is used where the network is not 100 percent physi cally secure or where physical security needs enhancement for example banks trading rooms or classroom training facilities EAP supports client access to the network and interoperates with Microsoft Windows XP and other standards based clients SNMPv3 provides user authentication and data encryption for higher security It also offers secure configuration and monitoring IP Manager List limits access to the management features of Ethernet Switch 470 by a defined list of IP addresses providing greater network security and manageability The Ethernet Switch 470 features MAC address based security which allows authentication of all access not only to the switches for management and configurations but also access to the infrastructure through these switches This software feature limits access to only network authorized and trusted personnel including full tracking of network connections Network access is granted or denied via proper MAC address up to a maximum of 448 identification In addition with the D
22. th 1 port IOOOBaseWDM GBIC with Avalanche Photo Diode Receiver 1530nm Wavelength 1 port IOOOBaseWDM GBIC with Avalanche Photo Diode Receiver 1550nm Wavelength 1 port 1OOOBaseWDM GBIC with Avalanche Photo Diode Receiver 1570nm Wavelength 1 port IOOOBaseWDM GBIC with Avalanche Photo Diode Receiver 1590nm Wavelength 1 port IOOOBaseWDM GBIC with Avalanche Photo Diode Receiver 1610nm Wavelength AA1419002 E5 AA1419003 E5 AA1419004 E5 AA1419042 E5 AAI419017 E5 AA1419018 E5 AA1419019 E5 AA1419020 E5 AA1419021 E5 AA1419022 E5 AA1419023 E5 AA1419024 E5 Redundant Power Supply Order No Description AA0005017 E5 Ethernet Routing Switch RPS 15 Chassis up to three RPS 15 modules can be installed in the chassis Ethernet Routing Switch RPS 15 600 watt RPS module 1 DC cable per RPS module required AA0005 19 E5 AA0005018 E6 Redundant Power Supply 15 Connecting Cable 6ft 1 8m for a Single 470 PWR 48 V DC to DC converter for use with RPS 15 For use with 470 24T or 48T Redundant Power Supply 15 Long Connecting Cable 7 6m 25ft for up to 4 x ES 470 Redundant Power Supply 15 Short Connecting Cable 3m 10ft for up to 4 x ES 470 AL1904005 E5 AA0005020 E6 AA0005021 E6 Maintenance services Order No Description GE5300xxx Technical Support Service GL5300xxx Return amp Replace Service GF5300xxx Managed Spares Services Pack Next Business Day GG5300xxx Managed Spares Second B
23. through the serial port on the console ASCII Configuration File The Ethernet Switch 470 can download a user editable ASCII configuration file from a Trivial File Transfer Protocol TFTP server The ASCII configuration file can be loaded automatically at boot time or on demand using the manage ment systems console menus or CLI Once downloaded the configuration file automatically configures the switch or stack according to the CLI commands in the file This feature allows the flexi bility of creating command configuration files that can be used on several switches or stacks with minor modifications ASCII Configuration Generator The ASCII Configuration Generator allows the configuration settings of the switch to be displayed or saved to an external ASCII configuration file made up of a series of CLI commands This editable ASCII configuration file can then be uploaded to a switch from an external file server Power Redundancy Redundant power support With connectivity to the RPS15 the Ethernet Switch 470 delivers redundant power supply support crucial in mission critical environments Nortel s RPS15 Power Supply Unit is capable of having up to three 600 watt power supply modules Each power module can provide redundant power supply support to one 470 PWR or up to four 470 switches A DC cable connector cable is required to connect from an Ethernet Switch 470 to an RPS15 module see ordering information section
24. usiness Day GH5300xxx Managed Spares Services Pack 4 Hour 7x24 GJ5300xxx Managed On Site with Spares Services Pack Next Business Day GK5300xxx Managed Onsite with Spares SBD Svc Pack GN5300xxx Managed On Site with Spares Services Pack 4 Hour 7x24 Note Replace XXX with 543 for 470 24T or 470 24T PWR Replace XXX with 376 for 470 48T or 470 48T PWR The seventh character of the switch order number must be replaced with the proper code to indicate desired product nationalization A No power cord included BI Includes European Schuko power cord common in Austria Belgium Finland France Germany The Netherlands Norway and Sweden C Includes power cord commonly used in the United Kingdom and Ireland D Includes power cord commonly used in Japan ET Includes North American power cord EI Includes Australian power cord also commonly used in New Zealand and the People s Republic of China In the United States In Europe Nortel Nortel 35 Davis Drive Maidenhead Office Park Westacott Way Research Triangle Park NC 27709 USA Maidenhead Berkshire SL6 3QH UK In Canada In Asia Nortel Nortel 195 The West Mall United Square Toronto Ontario M9C 5K1 Canada 101 Thomson Road Singapore 307591 In Caribbean and Latin America Phone 65 6287 2877 Nortel 1500 Concorde Terrace Sunrise FL 33323 USA Nortel is a recognized leader in delivering communications capabilities that enhance the
Download Pdf Manuals
Related Search