Antec TRUE430PGB UK version of True430 AC 430W ATX
Contents
1. with European standard regulation code EN61000 3 2 By altering the input current wave shape PFC improves the power factor of the power supply and results in increased energy efficiency reduced heat loss prolonged life for power distribution and consumption equipment and improved output voltage stability Installation Note not applicable to models designed for the European Union Check the red power supply voltage switch setting before installation It should be the same as your local power voltage 115V for North America Japan etc and 230V for Europe and many other countries Change the voltage setting if necessary Failure to take this precaution could result in damage to your equipment and could void your warranty 1 Disconnect the power cord from your old power supply 2 Follow your computer case manual and open the case 3 Disconnect all the power Connectors from the motherboard and from the peripheral devices such as case fans hard drives floppy drives etc 4 Remove the existing power supply from your computer case and replace it with the Antec power supply 5 Connect the Power Connectors to your motherboard and peripheral devices 6 Connect the case fans to the dedicated fan connectors Note Do not connect other devices except fans to these connectors You may connect case fans to the regular 4 pin Peripheral connectors if you choose not to utilize TruePower Circuitry on your case fans 7 Connect the 3 pin fan2. Fail Delay Time 1ms min T5 Power Good Hold Up time 20ms min 115V 230V FULL LOAD 1ms minimum SENSE LEVEL OVER VOLTAGE 5V 6 5V max 12V 15 6V max 3 3V 4 1V max 4 5 AC V AC ON AC OFF PS ON HIGH LOW T1 T2 T3 T5 T4 TURN ON POWER GOOD ON RING OFF RING POWER FAIL HIGH HOLD UP P G WAVE FORM VB 4 75V 5V Wave Form 4 1 REMOTE ON OFF CONTROL The power supply is turned on or off by TTL signal Remote On Off Signal Characteristics 4 2 AUXILIARY 5VSB This power supply is specifically equipped with an independent stand by 5V output current 2 0A max This output will always provide 5V except when the AC line is cut off 4 3 AUTO RESTART If the output of the power supply drops out of the regulation caused by AC line Voltage the power supply will automatically resumes normal operation only after the AC line voltage returns to the specified operating range 5 0 ENVIRONMENT Ambient operation temperature 10 C to 50 C Ambient operation relative humidity 20 to 85 Ambient storage temperature 40 C to 70 C Ambient storage relative humidity 10 to 95 Figure 1 Active low Power supply turn on Active high Power supply turn off PS ON MIN MAX Vil input low voltage 0 8V Vil input low current Vin 0 4V 1 6mA Vih input High voltage lin 200uA 2 0V Vih open circuit lin 0 5 25 6 0 CE REQUIREMENTS 6 1 EMI 1 MEET FCC CLASS B 2 MEET EN55022 CLA
3. NECTOR FAN ONLY CONNECTOR Pin Signal 24AWG Wire 1 SENSOR Blue 2 NONE 3 COM Black Pin Signal 16AWG Wire 1 COM Black 2 COM Black 3 COM Black 4 3 3VDC Orange 5 3 3VDC Orange 6 5VDC Red Pin Signal 20AWG Wire 1 COM Black 2 COM Black 3 12VDC Yellow 4 12VDC Yellow Pin Signal 18AWG Wire 1 12VDC Yellow 2 COM Black 3 NO PIN 4 NO PIN
4. Power Connector you can still use this power supply The TruePower power supply is also equipped with a 3 pin fan signal connector Connect it to one of the fan connectors on your motherboard You may monitor the speed of the rear power supply fan through your motherboard BIOS or through the monitoring software that comes with your motherboard Note The speed of the fan may be as low as 1500 RPM when temperatures are low At these speeds some motherboards may not be able to properly detect the fan speed and may generate false warnings of fan failure Please refer to your motherboard manual for proper fan monitoring set up Power Switch This power supply comes with a main power switch Make sure you turn the switch to the ON I position before you boot up your computer for the first time In normal operation there is no need to turn the switch to the OFF O position since the power supply is equipped with a soft on off feature which turns your computer on and off through the soft switch on your computer case You may need to turn the switch to the OFF position occasionally should your computer crash and you cannot shut it down through use of the soft switch Antec TruePower User s Manual Antec TruePower ATX12V power supply Models TRUE330 TRUE380 TRUE430 TRUE480 TRUE550 1 Applicable only to models designed for sale in the European Union TruePower models designed for the EU include Power Factor Correction PFC circuitry in accord
5. SS B 6 2 ESD MEET IEC 801 2 8KV 6 3 EFT BURST MEET IEC 801 4 2KV 6 4 SAFETY REQUIREMENTS 1 MEET UL 1950 2 MEET IEC 60950 7 0 MTBF 80 000 hours at 25 C demonstrated 8 0 DC CONNECTOR AND CASE REQUIREMENTS ATX MAIN CONNECTOR P1 HOUSING P N P20 I42002 or equivalent TERMINAL P N I42002BS 2 or equivalent PERIPHERAL POWER CONNECTOR FLOPPYDRIVE POWER CONNECTOR P2 P4 P6 P7 P8 P9 P10 P3 P5 HOUSING JMT JP1120 4 HOUSING JMT JP11635 4 HOUSING WST P4 A10202 OR EQU HOUSING WST P4 I25001 OR EQU TERMINAL JMT J1120BS 2 TERMINAL JMT J11635BS 2 TERMINAL WST A10209BS 2 TERMINAL WST I25001BS 2 OR EQU 16AWG Wire Signal Pin Pin Signal 16AWG Wire Orange 16AWG 3 3VDC 11 1 3 3VDC Orange Brown 22AwG 3 3V 11 default sense Blue 18AWG 12VDC 12 2 3 3VDC Orange Black COM 13 3 COM Black Green 18AWG PS ON 14 4 5VDC Red Black COM 15 5 COM Black Black COM 16 6 5VDC Red Black COM 17 7 COM Black White 18AWG 5V 18 8 POK Gray 18AWG Red 5VDC 19 9 5VSB Purple 18AWG Red 5VDC 20 10 12VDC Yellow Pin Signal 18AWG Wire 1 12VDC Yellow 2 COM Black 3 COM Black 4 5VDC Red Pin Signal 22AWG Wire 1 5VDC Red 2 COM Black 3 COM Black 4 12VDC Yellow 6 AUXILIARY POWER CONNECTOR PS1 HOUSING WST P N P20 I42002 or equivalent TERMINAL WST P N I42002BS 2 or equivalent 12V CONNECTOR HOUSING MOLEX 39 01 2040 or equivalent TERMINAL MOLEX 39 29 9042 or equivalent FAN SPEED MONITORING CON
6. User s Manual 1 Antec Low Noise Technology The Antec TruePower power supply is equipped with special circuitry to achieve optimum balance between noise reduction and necessary cooling Thanks to an advanced temperature response system the power supply fans run at the lowest speed appropriate to load and conditions The result is a great reduction in overall noise even in comparison to traditional thermally controlled fans Your TruePower power supply can also monitor and control the system case fan speed There are two dedicated fan connectors marked Fan Only from the power supply for system case fans You may connect your case fans to them and have the TruePower circuitry control the speed of the case fans Note Please do not connect more than three external fans to the Fan Only connectors in any combination For maximum cooling you may choose to connect the case fans to the regular 4 pin peripheral connectors but in this fashion noise will not be reduced Connectors The Antec TruePower power supply is an ATX12V form factor power supply An ATX12V power supply has a single 20 pin Main Power Connector a 6 pin AUX Power Connector and a 4 pin 12V Power Connector to the motherboard It also comes with seven 4 pin Peripheral Power Connectors and two 4 pin Floppy Drive Power Connectors to your drives It is backwards compatible to previous ATX form factor power supplys If your motherboard does not support the AUX Power Connector or the 12V
7. ceramic capacitor to simulate system loading to measure it 3 At peak load 12V output regulation 10 2 1 HOLD UP TIME 20ms minimum Test Condition Full load AC input 115V or 230V 60Hz or 50Hz 2 2 LOAD TRANSIENT RESPONSE STEP LOAD Step load changes up to 20 of full load while other loads remains constant within the rating The load waveform shall be a square wave with the slope of the rise and fall at 0 1A usec and the frequency shall be from 10Hz to 1 kHz The DC output voltage will stay within regulation during the step load changes 2 3 OVERSHOOT Overshoot at turn on or turn off shall be less than 10 of the nominal output voltage 3 0 PROTECTION If the power supply latches into shutdown stage when over current over voltage or short circuit protection is working the power supply shall return to normal operation only after the fault has been removed and PS ON is reset for a minimum of 1 Second or remove AC power is removed and re applied 3 1 OVER CURRENT PROTECTION Overload currents applied to each tested output rail will cause output trip before they reach or exceed 110 150 for testing purposes Overload currents should be ramped at a minimum rate of 10 A s starting from full load 3 2 OVER VOLTAGE PROTECTION 3 3 SHORT CIRCUIT PROTECTION All output to GND 4 0 TIME SEQUENCE T1 Turn On Time 500ms max T2 Output Voltage Sequencing 20ms max T3 Power Good Delay Time 100ms lt t3 lt 500ms T4 Power
8. signal connector to one of the fan connectors on your motherboard Note You do not need to connect the 3 pin fan signal connector in order to make the power supply work if you choose not to monitor the speed of the fan 8 Close the computer case 9 Connect the power cord to the Antec power supply 2 3 Specifications 1 0 INPUT 1 1 VOLTAGE 1 2 FREQUENCY 47Hz 63Hz 1 3 CURRENT 1 4 INRUSH CURRENT 115V 50A max 230V 80A max at 25 C cold start 1 5 POWER EFFICIENCY 68 min at full load 115 230Vac 60Hz 50Hz 2 0 OUTPUT Note 1 The continuous maximum total output power RANGE MINIMUM NOMINAL MAXIMUM UNITS 1 90 115 135 VRMS 2 180 230 265 VRMS 115V 230V TRUE330 7A 4A TRUE380 8A 5A TRUE430 9A 5A TRUE480 12A 6A TRUE550 12A 6A VOLTAGE 5V 12V 3 3V 5V 12V 5VSB MAX LOAD TRUE330 30A 17A 28A 0 5A 1 0A 2 0A TRUE380 35A 18A 28A 0 5A 1 0A 2 0A TRUE430 36A 20A 28A 0 5A 1 0A 2 0A TRUE480 38A 22A 30A 1 5A 1 0A 2 0A TRUE550 40A 24A 32A 0 5A 1 0A 2 0A MIN LOAD 0A 0 8A 0A 0A 0A 0A REGULATION 3 3 3 5 5 5 RIPPLE amp NOISE 50 120 50 50 120 50 mV TOTALMAX 5V 12V amp 3 3V OUTPUT MAX OUTPUT TRUE330 330W 310W TRUE380 380W 360W TRUE430 430W 410W TRUE480 480W 460W TRUE550 550W 530W 2 Peak surge current 15 sec max Measurements shall be made with an oscilloscope with 20MHz bandwidth 10uF elec trolytic capacitor parallel 0 1uF
Download Pdf Manuals
Related Search