Home

Philips Plasma TV 42" Digital Crystal Clear

1. Warning concerning stationary images on the TV screen A characteristic of Plasma Display Panels is that displaying the same image for a long time can cause a permanent after image to remain the screen This is called phosphor burn in Normal use of the TV should involve the showing of pictures that contain constantly moving and changing images that fill the screen Examples of stationary images this is not an all inclusive list you may encounter others in your viewing TV and DVD menus listings of DVD disk content Black bars when black bars appear at the left and right side of the screen it is recommended to change to a picture format so that the picture fills the entire screen TV channel logo present a problem if they are bright and stationary Moving or low contrast graphics are less likely to cause uneven aging of the screen Stock market stickers presented at the bottom of the TV screen Shopping channel logos and pricing displays bright and shown constantly or repeatedly in the same location on the TV screen Examples of still pictures also include logos computer images time display teletext and images displayed in 4 3 mode static images or characters etc Notes reduce contrast and brightness when viewing once burn in occurs it will never disappear completely 25 f SA M 4 M PHILIPS 2 9 lt gt Cinema
2. Press on the remote control to switch off the internal loudspeakers of the TV The headphone impedance must be between 8 and 4000 Ohm The headphone socket has a 3 5 mm jack In the Sound menu select Headphone volume to adjust the headphone volume Multi channel Surround receiver Connect the audio cable to the multi channel Surround receiver and to AUDIO OUT L and R at the bottom of your TV 1 CENTRE IN If you want the loudspeakers of your TV to act as centre a speaker also connect an audiocable to the multi channel 99x c Surround receiver and to the CENTRE at the bottom of 3 your TV 2 Select Centre Input On in the Source menu See p 10 The loudspeakers of the TV will now only produce centre sound the loudspeakers connected to the audio receiver will produce Surround Sound The volume has to be controlled via the multi channel Surround receiver Note No sound will be heard when a TV channel or external source is blocked via the Child lock menu see p 13 Connect extra subwoofer To enhance the sound reproduction of your TV you can connect an externally powered subwoofer between 20 and 250 Hz Connect the audio cable of the external subwoofer to the SUBWOOFER socket at the rear of your TV Select Subwoofer in the Setup General menu p 9 Adjust the frequency of the external subwoofer to 100 120 Hz according to your personal preference if p
3. Previously selected teletext page Only possible in case there is no list of favourite teletext pages available See 18 Press the key Select the index teletext page Press the grey colour key gt to display the main index usually p 100 Only for T O P teletext broadcasts Press i A T O P overview of the teletext subjects available is displayed Select with the cursor up down left right the desired subject and press the OK key Not all TV channels broadcast T O P teletext Select subpages When a selected teletext page consists of different subpages a list of available subpages appears on the screen Press the cursor left or right to select the next or previous subpage Picture Teletext Press the key Press the B key to show Teletext on the right of the screen Use the cursor keys to select a TV channel Press the GB key to switch off dual screen Enlarge a Teletext page Press repeatedly to display the upper teletext part the lower teletext part and then to return to the normal teletext page size When the teletext page is enlarged you can scroll the text line by line using the cursor up down Hypertext With hypertext you can quickly jump to a pagenumber or search for a specific word shown on the current teletext page Press the OK key to highlight the first word or a number on the page Use the cursor up down left right to select any other word or number yo
4. Frekvence pou van n kter mi televizn mi spole nostmi mohou li it od daj uveden ch v tomto seznamu Informujte se bl e u p slu n spole nosti nebo v prodejn kde jste televizor koupili SK Frekvencie pou van niektor mi spolo nos ami telev zneho prenosu sa m u li i od dajov uveden ch v tomto zozname Informujte sa bli ie u pr slu nej spolo nosti alebo v predajni kde ste telev zor k pili EUROPE E EUROPE FREQ MHz CAN FREQ MHz R1 FRANCE CAN FREQ MHz 55 75 60 50 63 75 176 0 184 0 192 0 7002 5 7 ef GBA
5. Shift Special Press the cursor right to enter the keyboard Press the cursor left right up down to select the characters words or functions Press the OK key to confirm each character selected 18 Select Cancel to cancel the word Space to enter a space Delete to delete the last character selected Shift to switch between lowercase or capital characters Special to display special characters on the keyboard and press the OK key Press the cursor left repeatedly to return to the Teletext menu again Searching a word Type in the word on screen or select a word from the history list on the right and press OK Select Accept and press OK again The message Searching appears To cancel the searching or to search for a new word select Keyboard and press OK When a word is not found message appears When the word is found it is highlighted in the teletext page To continue the search press the OK key Cycle subpages if available Makes the subpages cycle automatically Press the cursor right to activate and to de activate again Timed page To display a specific page from a selected TV channel at a certain time Press the cursor right and select Yes or No Enter the time and pagenumber with the cursor keys or the digit keys Notes feletext does not have to remain switched on but you should watch the TV channel you have selected the specific page from It is no
6. watch locked channels 4 digit code must be entered The Set Change code menu item allows you to create or change a Personal Identification Number PIN Select Set Change code If no code exists yet the menu item is set to Set code If a code has previously been entered the menu item is set to Change code Follow the instructions on screen Important You have forgotten your code 0 0 0 Select Change code the General menu and press Press the cursor right and enter the overriding code 8 8 8 8 Press the cursor again and enter a new personal 4 digit code The previous code is erased and the new code is stored Source Source Setup EXT1 EXT2 EXT3 DVI Side Centre input Centre in volume This menu allows you to indicate the peripheral you connected to one of the external inputs Press the cursor right to enter the list of types of peripherals attached to the selected input Select the peripheral device with the cursor up down Decoder Decoder Setup If a decoder a descrambler is connected see p 19 you can define one or more programme numbers as decoder programme numbers Programme Status TV Setup Demo Auto demo Install Dealer demo Digital options Light sensor 3D Y C Comb filter Once you have selected the source type e g DVD this source will automatically be selected when your remote control is in DVD mode see p 3 and when you press
7. a programme number between 90 and 99 see Manual installation p 6 See the handbook of your recorder CABLE Decoder and Recorder Connect a eurocable 4 to your decoder and to the special euroconnector of your recorder See also the recorder handbook See Decoder p 10 You can also connect your decoder directly to EXT1 2 with a eurocable RECORDER DECODER Other equipment satellite receiver decoder DVD games etc Connect the aerial cables 4 2 and 3 as shown CABLE only if your peripheral has TV aerial in output Connect your equipment with 4 to one of the euroconnectors EXT1 2 or 3 to obtain a better picture quality EXTERNAL ae aw ake selection the Setup Source menu 10 ions Mak Setup 5 10 m MR L1 RECORDER Look for the test signal of your peripheral in the same way as you do for a recorder 19 Side connections Camera Camcorder or Game Connect your camera camcorder or Game as shown Connect to VIDEO 2 and AUDIO L 3 for mono equipment For stereo equipment also connect AUDIO R 3 S VHS quality with an S VHS camcorder is obtained by connecting the S VHS cables with the S VIDEO input 1 and AUDIO inputs 3 Do not connect cable and at the same time This may cause picture distortion Headphone Insert the plug into the headphone socket fj as shown
8. one peripheral should be provided with the Cinema Link functionality to benefit from this feature To take advantage of the highest quality of multi channel Surround sound it is advisable that you have a Cinema Link audio receiver connected The peripherals connected don t need to see the TV remote control in the Cinema Link system The commands given to the TV are automatically passed to the other peripherals This allows you to put the peripherals behind the doors of a cabinet or to place them in another room To enjoy Digital Surround playback the digital device e g DVD should be connected to the digital input of the audio receiver with a separate cinch audio cable 4 In case your TV is provided with a DIGITAL AUDIO OUT connector also connect it to one of the digital input connectors of your audio receiver 5 you connect the digital audio output connector of your TV and or peripheral equipment to a digital input connector of your audio receiver 4 and 5 if present select the appropriate digital input 1 or 2 in your audio receiver The optional wireless speakers of the TV cannot be used Preparation and Operation and Operation Cinema Link is switched on as soon as the audio receiver and the TV are switched on If necessary Cinema Link may be switched off or on again only on the audio receiver See the instructions for use of your audio receiver Important W hen Cinema Link is switched on all audio commands cont
9. resolution and increases the number of lines by 33 You may consider to select Movie Plus in case a halo effect should disturb you Dependent on your own preference select Progressive scan Dynamic contrast Sets the level at which the TV automatically enhances the details in dark middle and light areas of the picture DNR This sets the level at which noise is measured and reduced in the picture Colour enhancement This makes the colours more vivid and improves the resolution of details in bright colours Hue This compensates for the colour variations in NTSC encoded transmissions Picture format This will adjust the size of the picture dependent on the broadcast format and your preferred setting See also Use of the remote control Picture format p 4 11 Active Control The TV continuously measures and corrects all incoming signals in order to provide the best picture possible Press the key the remote control Note Switch off all menus on screen The Active Control menu appears Press the cursor up down to select the Active Control values Off Minimum Medium or Maximum The picture settings are being optimised continuously and automatically which is displayed by bars Those menu items can not be selected Q Press the cursor right to select Smart Picture Press the cursor up down to select one of the predefined picture settings Sound Sound Smart sound Equaliz
10. settings press the key 13 NEXT ViEeW Teletext guide NEXTVIEW NEXTVIEW is an electronic guide that allows you to look up programmes as you would in a newspaper or a TV magazine You can sort the programmes by subject films sport obtain detailed information and programme your recorder if it comes with the NEXTVIEWLink function As the NEXTVIEW service is only available on certain programmes and in certain countries the NEXT ViEW service has been set default to OFF in the factory The Teletext Programme Guide appears in its place This is based on teletext programme information if available and offers most functions of If you want to make use of the NEXTVIEW service you may decide to switch ON the NEXTVIEW option Press simultaneously and continuously for at least 4 seconds the MENU key at the right side of your TV and the digit key 1 on your remote control The TV turns to standby Switch your TV on again Additional consequences The NEXT VIEW provider menu item and the option Themes in the Smart surf menu appear the General Setup menu See p 8 Note broadcaster is responsible for the content of the information To switch OFF the NEXTVIEW option again Press simultaneously and continuously for at least 4 seconds the MENU key at the right side of your TV and the digit key 0 on your remote control Q The TV turns to standby Switch your TV on again
11. the cursor in the up down direction to select the TV activate Setup Demo or Install menu return or switch Use the cursor left right to select Picture Sound or main menu on off Features Note Sometimes not all the menu items are visible on the screen z indicated by a cluster of blue balls Use the cursor down or right to reveal all items Press the key to get Use the cursor in the left right direction to select the menu information about the selected item menu item Use the cursor up down again to select the control you want to select or to adjust Note Items temporary not available or not relevant are displayed in a light grey colour and cannot be selected Installation The installation menu contains the following items Language Country Automatic Manual Give name Reshuffle Favourite install install programmes Install EasyLink If your recorder has an EasyLink function during installation the language country and available channels are automatically transmitted to the recorder Select the menu language and country Language Install Press the MENU key on the remote control English Use the cursor down to select Install Deutsch Use the cursor right to select Language Francais Follow the instructions on screen Use the cursor up down to select your preferred language and press the OK key to confirm your selection Country Use the cursor right to select Country Instal
12. to summon the main menu Note Dependent on the input signal one or more menu items may not be selectable Press the key on the remote control to get information about the selected menu item Picture menu Sound Features Picture TV Smart picture Contrast Brightness Colour Sharpness Tint Digital options Dynamic contrast DNR Colour enhancement Hue Picture format Press the cursor right to select Picture Select the menu items in the Picture menu with the cursor up down Adjust the settings with the cursor left right or enter the list of submenu items with the cursor right Select a submenu item with the cursor up down Note remove the menu background before ddjusting the picture settings see Select TV setup General p 8 Smart picture Select Smart picture to display a list of predefined picture settings each corresponding with specific factory settings Personal refers to the personal preference settings of picture in the picture menu Note This Philips Flat TV has been set at the factory to look best in bright store environments which use fluorescent lighting As your home will likely not be well lit as a store we recommend you that you cycle through the various Smart picture modes to find the one that best suits your own viewing conditions Most consumers will find that Natural is the correct choice Digital options Pixel Plus is the most ideal setting doubles the horizontal
13. FLATIV SEE EVERY THING EXPERIENCE EVERY THING Hi 1 Information for users the UK Not applicable outside the UK Positioning the TV For the best results choose a position where light does not fall directly on the screen and at some distance away from radiators or other sources of heat Leave a space of at least 5 cm all around the TV for ventilation making sure that curtains cupboards etc cannot obstruct the air flow through the ventilation apertures The TV is intended for use a domestic environment only and should never be operated or stored in excessively hot or humid atmospheres General Points Please take note of the section Tips at the end of this booklet Interference The Department of Trade and Industry operates a Radio Interference Investigation Service to help TV license holders improve reception of BBC and IBA programmes where they are being spoilt by interference If your dealer cannot help ask at a main Post ffice for the booklet How to improve Television and Radio Reception Mains connection Before connecting the TV to the mains check that the mains supply voltage corresponds to the voltage printed on the type plate on the rear panel of the TV If the mains voltage is different con sult your dealer Important This apparatus is fitted with an approved moulded 13 Amp plug To change a fuse in this type of plug proceed as follows 1 Remove fuse cover and fuse 2 Fit new fuse w
14. Link is a new Philips feature in which the TV the audio C receiver and other video peripherals communicate with each other Note The Cinema Link on condition they all are equipped with the Cinema Link functionality is only available functionality and are connected via a eurocable T hey auto matically with devices of the Cinema Link offer the highest quality combination of picture and multi channel P50 3 generation surround sound to create your own Home Cinema W ith one key on the remote control with which you can control all Cinema Link products your total Cinema Link system will be started and the DVD or video recorder will start to play and the audio receiver will provide the sound on the condition Cinema link is Recommended enabled on behalf of the TV TheTV or monitor can function as the centre speaker of your Do not use the AC outlet at system making a separate centre speaker unnecessary only in case the back of the audio receiver your TV or receiver box is equipped with a Centre IN connector to power the DVD or the By pressing the standby key on the remote control for at video recorder in a Home least 3 seconds the complete Cinema Link system will be Cinema configuration switched to standby Configuration of the Cinema Link peripherals The connection diagram in the inside cover shows you how to connect the Cinema Link peripherals with each other N otes Besides the TV or receiver box at least
15. The provider menu item and the option Themes the Smart surf menu in the General Setup menu are no longer available Call NEXTViEw Teletext guide Press the key the remote control to call the NEXTViEWw Teletext guide menu appears with the message One moment please After a while you obtain NEXT VIEW page if the selected channel broadcasts this service the NEXTVIEW logo is displayed teletext page if the selected channel does not broadcast NEXT VIEW No information available is displayed if neither NEXTVIEW nor teletext are transmitted In this case select another channel Display of a NEXTVIEW page The information is set by the channel that transmits the NEXTVIEW service See also Setup menu General NEXTVIEW provider p 8 Programme name and broadcast time puck NEXTVIEW guides 05 Mon 05 Feb 18 00 e Time Channel Theme 05 e Menu 18 00 eChannel eTheme Mon 03 04 News Wed 0 Simpsons Fri 07 FR2 18 00 On a tout essay SexTV IEW 2 Review 9 Record 9 Remind Watch Lock Provider menu Record 6 Remind Watch 8 Lock This logo is only displayed during a NEXT VIEW transmission or when one of the externals is selected No logo indicates a teletext programme guide 14 function keys NEXT ViEW guides Use the cursor key left right to select Time Channel Theme the Date guide The Time gu
16. V lights up and the screen comes on If the TV is in standby mode press the P keys or the 1 key on the remote control Keys on the right side of the TV om 4 Cum ED Picture Sound Features Setup Demo Install Exit Should your remote be lost or broken you can still change some of the basic settings with the keys on the right side of your TV Press the 21 key to adjust the volume the P CH key to select the TV channels sources Press the MENU key to summon the main menu without the remote control Use the 1 key and the P CH key to select menu items in the directions as shown the MENU key to confirm your selection Note When activated via the MENU key on the right side of the TV only Exit lets you remove the menu Navigate to Exit and press the MENU key Use of the remote control 1 Note For most keys pressing a key once will activate the function Pressing a second time will de activate it When key enables multiple options a small list will be shown Press repeatedly to select the next item in the list The list will be removed automatically after 6 seconds or press OK to remove immediately Remark in mode only some keys are valid ON VCR DVD SAT AMP CD See Audio and Video equipment keys p 23 amp Select your peripherals See p 22 N P N 6 44 5 gt gt Audio and Video equipment keys see p 23 I
17. channels is done channel by channel You must go through every step of the Manual Manual install Installation menu Install Select Manual install in the Install menu Selection mode Press the cursor down System Follow the instructions on screen Programme Search Note Search or direct selection of a TV channel Fi If you know the frequency the C or S channel number enter the Ine tune es 3 or 2 digits of the frequency or the channel number directly with the digit keys 0 to 9 eg 048 Repeat to search for another TV channel after you have stored the selected TV channel Give name Give name Install Select Give Name in the Install menu and apis press the cursor down lt a gt ABCDEFG 123 Select the programme number BBC2 HIJKLMN 456 Note keep the cursor up down pressed to scroll CNN OPQRSTU 789 through the programme list quickly TVE VWXYZ 0 Press the cursor right ds A keyboard appears on the screen Shift Special Press the cursor right to enter the keyboard Press the cursor up down left right to select the first character and press OK Repeat for every character you want to enter Select Space to enter a space Delete to erase the highlighted character in the name entered Shift to display upper or lowercase characters on the keyboard Special to display special characters on the keyboard Press OK to confirm It is possible to change the name
18. chh ndler oder Ihre abelfernsehgesellschaft die Ihnen die zutreffenden Frequenzen mitteilt F Les fr quences utilis es par une soci t de t l distribution peuvent tre diff rentes de celles sur la liste des fr quences Consultez votre soci t de t l distribution ou votre revendeur pour des informations plus d tail es NL De frequenties die gebruikt worden door een kabelmaatschappij unnen verschillen van deze op de tabel Raadpleeg uw kabelexploitant of uw handelaar voor meer informatie 1 Le frequenze usate per una societa di teledistribuzione possano essere differenti di quelle nella tabella Consultate la societa di teledistribuzione il vostro rivenditore per informazione specifica E Las frecuencias utilizadas por las empresas de distribuci n de sefial por cable pueden ser diferentes de las que se encuentran en esta tabla Consulte con su de distribuci n de televisi n por cable o con su distribuidor para que le proporcionen una informaci n m s detallada P As frequ ncias utilizadas por uma sociedade de teledistribuic o podem ser diferentes das indicadas na lista de frequ ncias Consultar a sociedade de teledistribuigdo ou o vendedor para informa es mais detalhadas DK Frekvenser benyttet af kabel operat rer kan v re afvigende fra disse kantakt deres kabel operat r eller forhandler for n mere informa tion N Frekvensene som benyttes pa et kabelnett kan avvike fra de som e
19. cies are amplified so that the natural balance is restored 3D effect Night mode 3D effect Audio O nly 3D effect enables you to experience the effect of Dolby Surround Pro Logic without the need of having rear speakers connected or activated Select the level of 3D effect with the cursor left right Night mode only functional with Dolby Digital sound broadcasting input The loud parts of the sound are lowered and the soft passages are raised You can enjoy surround sound without disturbing sleeping children or neighbours Audio only This control enables you to blank the TV picture if the TV or monitor is used as centre speaker in the Cinema Link system and if the audio receiver is reproducing sound unrelated to aTV picture Switch Audio only On to only hear the sound and to switch off the picture The message Audio only appears on screen Surround menu D ependent on the audio receiver speakers configuration you may not be able to select certain menu items Adjustment of the volume level of the loudspeakers Note the test tone function is automatically cancelled by the audio receiver when leaving the Surround menu Select Test Tone On A steady noise tone is switched sequentially through the available loudspeakers except for the subwoofer for 2 seconds each T his enables you to have a reference of the loudness of each Surround Receiver Test Tone Front left volume Front right volume Centre volume Rear volume lou
20. coder programme numbers This menu allows you to change various settings that are presumably adjusted less frequently than most other settings Press the key on the remote control to get information about the selected menu item Menu background Select Yes or No to turn the menu background on or off Smart surf Select Smart surf With the cursor left right select 2 programmes if you want the key to toggle between the current and the previously selected channel 9 programmes if you want the P P key to summon a list of up to 9 channels which can be selected Themes if you want the key to quickly select TV programmes if NEXTVIEW with defined themes is broadcast See p 14 To add remove a channel or source to the 9 programmes list Tune to the channel or source you wish to add or remove Press the key and press the cursor right to add or remove Note If there are already 9 channels sources in the list the one at the bottom of the list will be removed Factory settings This resets the picture and sound settings to their predefined factory values but maintains the channel installation settings NEXT VIEW provider Select a TV broadcaster that provides NEXT VIEW data How to make use of NEXTVIEW see p 14 OSD On Screen Display Select OSD Select Normal to activate the continuous display of the programme number and extended display of TV channel and programme information on screen Min
21. ct Store and press the OK key Repeat steps to to store another radio station Give name Reshuffle ive name Reshuffle Give name Receiver 0 To assign or change a name to a radio station or to change the order of the stored radio stations according to your preference act in the same way as with giving a name or reshuffling the programme list of TV channels See the Instructions for Use of the TV or receiver box f EX M 4 di Table of TV frequencies Tabell ver TV frekvenser Frequenztabelle der Fernsehsender TV taajuustaulukko Liste des fr quences des metteurs Frequentietabel TV Zenders Tabella delle frequenze delle trasmittenti televizi ad llom sok frekvenci inak a list ja Lista de las frecuencias de las emisoras Lista cz stotliwo ci stacji nadawczych Lista das frequ ncias dos emissores Seznam frekven n ch p sem vys la Liste over TV senderne Zoznam frekven n ch p siem vysiela ov Tabell over TV frekvenser ITALY CAN FREQ MHz GB The frequencies used by a cable company may differ from the requencies on the table Consult your cable company or your dealer for detailed information D n Kabelfernsehanlagen k nnen Abweichungen von den in den Frequenztabellen aufgef hrten Frequenzen vorkommen Bitte wenden Sie sich an Ihren Fa
22. dio and video equipment keys This system remote control operates the following Philips equipment TV VCR DVD DVD R SAT RC5 RC6 TUNER CD CD R Press the Select key to operate any of the equipment indicated in the display Another device can be selected by pressing Select repeatedly within 2 seconds The led will blink slowly to indicate the device Press one of the keys on the remote control to operate the peripheral equipment To return to TV mode press Select while the led is blinking When no action is taken within 60 seconds the remote goes back to TV mode When you do not want the remote to go back to TV mode and to stay in the mode selected proceed as follows Select the desired mode with the Select key Wait until no LED is lit Press the Select key again simultaneously with the OK key for at least 2 seconds The remote will not go back to TV mode from now on and will remain in the mode selected To go back to the default setting of the remote TV mode repeat what is explained above selecting the TV mode Note When the Select key is pressed and held for more than 2 seconds the RC5 RC6 system select command is transmitted 0 to switch standby MENU to switch the menu on or off for pause VCR DVD CD P for chapter channel track selection 44 rewind VCR CD Oto9 digit entry search down DVD AMP tape index VCR for st select a DVD chapter 5 ae
23. displaying a message if the TV is on Lock to lock certain programmes to prevent recording or watching For the functions Record Remind or Lock a small menu pops up in which you can choose the interval once daily or weekly or clear an earlier made record remind or lock setting The default interval is set to Once To confirm the frequency press the OK key Watch to watch the selected and currently broadcast programme Acquisition and updating of NEXTVIEW information Acquisition and updating of NEXTVIEW is done when you are watching the TV channel of the selected NEXTVIEW provider see Setup menu p 8 or when the TV is switched to standby Acquisition of fresh data will happen once during the night Note it may be necessary to put the TV in standby mode when all NEXTVIEW information is outdated e g when returning from holiday 16 Teletext Most channels broadcast information via teletext This has 1200 pages memory that will store most broadcasted pages and subpages to reduce waiting time After each programme change the memory is refreshed Switch Teletext on and off Press to switch the teletext 5 102 03 04 05 06 07 BBC CEEFAX 102 09 10 11 12 LIONS RECORD ANOTHER WIN 430 Select a Teletext page Enter the desired page number with the digit keys the cursor keys up down left right or with the P key Select the options at the bottom of the screen with the colour keys
24. dspeaker and to adjust the level of each until they all sound Rear left volume equally loud Rear right volume The loudspeakers activated light up in the screen graphic Subwoofer volume Select the Surround menu items with the cursor up down one after another and alter the selected adjustments with the cursor left right The best result is achieved when all speakers have equal volume in your usual listening position Select Test tone Off when you have finished the adjustment of the Speaker levels Speakers menu D ependent on the audio receiver speakers configuration you may not be able to select certain menu items O nce the number and position of the loudspeakers has been fixed selecting C entre speaker Rear Speakers and Subwoofer Yes or N o you can adjust the initial receiver settings size and distance for optimal surround sound Note after changing the configuration the menu will disappear temporarily and re appear again after the new settings will be updated Size of the speakers Select Small if your speaker is able to reproduce low notes down to at least 80 100 Hz Select Large if your speaker is able to Speakers Receiver Centre speakers ig Yes No reproduce low notes down to at least 50 Hz Rear speakers Yes No Note Subwoofer present Yes no As a rule of thumb a large speaker has a cone diameter of at least Front speaker size Large Small 12 cms 5 inches See the specification sheet of yo
25. eferring to a page with more info about the programme press the OK key to display the information Press the OK key again to return to the programme guide page f the selected programme guide page satisfies the VPT Video programming via Teletext requirements it will be possible to record remind watch or lock programmes the TV will remember the last selected teletext page number of that channel that contains programme guide information and indicates which programme starts at what time Every time you press the key the teletext programme guide page of the selected TV channel will be available When necessary you can select the subpage number by moving the cursor to the pageball and pressing right Note You must enter the teletext pagenumber for each channel You can change the channels also by moving the cursor up down in the list in the left of the page 15 Basic functions Press one of the grey red green yellow or blue keys to activate a NEXTVIEW Teletext Guide function The keys appear in grey if the function is not available Review this menu provides a list of programmes that are marked as reminders those that have to be recorded and those that are locked This menu can be used to change or remove marked programmes Record to programme the recording of the recorder if it has a NEXTVIEWLink function and is connected to EXT2 Remind automatically switch on the TV if it is in standby or by
26. er Volume Balance Loudness Headphone volume Surround mode Dual Mono Stereo Nicam Analogue 3D effect Notes Smart sound Press the cursor right to select Active Display Press the cursor up down to select Show bars one of the Dual screen demos or Off When you select Dynamic contrast Pixel Plus Digital Noise Reduction or Digital Natural Motion the TV screen is divided into two parts in the left part the selected picture quality setting is switched off in the right part it is switched on Note Dependent on the input signal one or more Dual screen demos may not be selectable Press the key again to switch off the Active Control menu Q Press the cursor right to select Sound Select the menu items in the Sound menu with the cursor up down and adjust the settings with the cursor left right Remember control settings are at normal mid range levels when the bar scale is centred Select Smart sound to display a list of predefined sound settings each corresponding with specific factory settings of Treble and Bass Personal refers to the personal preference settings of sound in the sound menu Some menu items are only available in case of a Cinema Link AVL configuration and when the Cinema Link is activated Others are Delta volume steered by the audio receiver instead of by the TV See the separate Cinema Link booklet supplied p 26 Dual HI is only available with dual sound tra
27. hen the surface becomes dusty please wipe gently with absorbent cotton or other soft materials like chamois soaks Do not use acetone toluene and alcohol because they cause chemical damage Do not use liquid cleaners or aerosol cleaners Wipe off saliva or water drops as soon as possible Their long time contact with the screen causes deformations and colour fading Poor Picture Have you selected the correct TV system in the manual installation menu s your TV or house aerial located too close to loudspeakers non earthed audio equipment or neon lights etc Mountains or high buildings can cause double pictures or ghost images Sometimes you can improve the picture quality by changing the direction of the aerial s the picture or teletext unrecognisable Check if you have entered the correct frequency See Installation Manual installation p 6 Are brightness sharpness and contrast out of adjustment Select Factory settings in the Setup General menu p 8 No Picture Are the supplied cables connected properly The aerial cable to the TV the other aerial to your recorder the VGA cables to the display the power cables Has the child lock been switched off s your PC switched on Do you see a black screen and the indicator in front of the TV lights up blue this means that the display mode is not supported Switch your VGA source to a correct display mode case of weak or bad signal cons
28. hich should be a BS1362 5A A S T A or BSI approved type 3 Refit the fuse cover In order to maintain conformity to the EMC directive the mains plug on this product must not be removed Connecting the aerial The aerial should be connected to the socket marked x at the back of the set An inferior aerial is likely to result in a poor perhaps unstable picture with ghost images and lack of contrast Make shift or set top aerials are unlikely to give adequate results Your dealer will know from experience the most suitable type for your locality Should you wish to use the set in conjunction with other equipment which connects to the aerial Socket such asTV games or a video camera it is recommended that you consult your dealer on the best method of connection Stand if provided Use only the stand provided with the set making sure that the fixings are properly tightened A dia gram showing how to assemble the stand is packed with the stand N ever use a make shift stand or legs fixed with woodscrews Cf 5 Due to continuous product improvements this manual is subject to change without notice End of directives Philips is paying a lot of attention to producing environmentally friendly in green focal areas Your new TV contains materials which can be recycled and reused At the end of its life specialised companies can dismantle the discarded TV to concentrate the reusable materials and to minimise the amou
29. ide provides an overview of all programme titles active in the selected time block The Channel guide provides an overview of all programmes that are broadcast by a single channel during one day With the Date guide you can choose a specific date The Theme guide displays a list of all programmes at the selected date that matches with the selected category Going through the menu guide the TV is collecting the sorting criteria to finally display a list of programme events Press the OK key to select the guide type Move the puck down and to the right to select the programmes If available a summary or commentary on the programme is displayed at the bottom of the screen Use the cursor up down to scroll through the programmes Picture NEXT VIEW Teletext guide Press the key Press the GB key to show NEXTViEw Teletext guide on the right of the screen Use the cursor keys to select a TV channel Press the GB key to switch off dual screen Teletext Guide Enter with the digit keys the teletext page number that contains the programme information for the current channel Press the cursor right to move the puck over the selection ball Use the cursor up down to scroll through the different programmes page ball selection ball subpages Mon 05 Feb 16 35 scroll ball 100 1 BBC CEEFAX channel list Review Record Remind Watch Lock If the selected programme contains a page number with an optional subcode r
30. imum to activate the display of reduced channel information Note When subtitles is switched on see Features p 13 display of the programme number is not possible Programme title Select Programme title Yes or No When selected Yes after the selection of aTV programme or after pressing the key the remote control TV channel which broadcasts teletext may transmit the name of the TV channel or the programme title Teletext 2 5 o oe Some broadcasters offer the opportunity to see more colours other background colours and nicer pictures in the teletext pages Select Teletext 2 5 Press the cursor right to select Teletext 2 5 On to take advantage of this feature Press the cursor right again to select Teletext 2 5 Off if you like the more neutral teletext layout The selection made is valid for all channels which broadcast teletext 2 5 Note It may take a few seconds before teletext broadcast switches over to Teletext 2 5 Auto Surround Sometimes the broadcaster transmits special signals for Surround Sound encoded programmes The TV automatically switches to the best surround sound mode when Auto Surround is switched On Subwoofer Select Yes if you installed an external subwoofer See Connect Peripheral Equipment Connect extra subwoofer p 20 Set Change code 0 0 The Child lock feature see Features 13 allows you to lock channels to prevent others from watching certain programmes
31. l Q Select the country where you are now located and press Austria the OK key Belgium Select Other when none of the countries applies Croatia Proceed with the Install menu Store TV channels channels After language and country are set correctly you can now search for and store the TV channels in two different ways using Automatic Installation or Manual Installation tuning in channel by channel Select your choice with the cursor right Automatic installation Select Automatic install in the Install menu Note All channels must be unlocked in order to autoprogram If requested enter your code to unlock all channels See TV Automatic install Features menu Childlock p 13 Install Press the cursor down The autoprogramming option label Start appears Install Start Press the cursor right The message Searching appears and the progress of autoprogramming is displayed If a cable system or a TV channel which broadcasts ACI Automatic Channel Installation is detected a programme list appears Without ACI broadcast the channels are numbered according your language and country selection You can use Reshuffle to renumber them See p 7 It is possible that the cable company or the TV channel displays a broadcast selection menu Layout and items are defined by the cable company or the TV channel Make your choice with the cursor and press the OK key Manual installation Searching for and storing TV
32. lock menu Important You have forgotten your code See 9 Select one of the menu items of the child lock menu Lock if you want to lock all channels and externals Custom lock and press the cursor right The items Age lock and Category lock are only available when NEXTVIEW broadcast is available Select Age lock if you want to lock programmes related to a certain age off 2 4 16 Lock after if you want to lock all programmes from a certain time onwards Press the cursor right and enter the time with the cursor up down and right Press the OK key to validate Programme lock if you want to lock a certain TV channel or external Category lock if you want to lock programmes related to a certain theme Movies Sports Shows Select Unlock to disable all locks you have set On timer Select On timer with the cursor down VCR1 Sunday BBC2 Monday orf CNN a On timer TVE Daily 15 45 Select On with the cursor right Press the cursor right again to enter the programme list Select the TV channel or external you want your TV to switch to on a selected time and day Press the cursor right again to select a day of the week or to select Daily Press the cursor right once again to enter the time with the digit keys or with the cursor up down and press the OK key to activate Press the MENU key to turn off the menu Note check your timer
33. mme list MENU Main menu on off see 5 lt 1 To adjust the volume Interrupt the sound or restore it P Programme selection To browse through the TV channels and sources stored in the favourite list 0 9 Digit keys To select a TV channel For a two digit programme number enter the second digit before the dash disappears To switch immediately to a selected one digit TV channel keep the digit key pressed a bit longer EM gl OOO 1009 s La Kes screen Movie expand 14 9 On Screen information Smart surf NEXTVIEW themes Active control see p 12 E Picture format ES Press to display when available information about the selected TV channel and programme Menu Remote control info When a menu is on screen press to display info on the selected menu item While the menu info is displayed press any key except the MENU or digit keys to display remote control info The normal function of the key is not executed With this key you can easily switch between 2 up to 9 different TV channels or sources or quickly select TV programmes if NEXTVIEW with defined themes is broadcast See General Smart surf p 8 Press the OK key or wait for the time out to dismiss the Smart surf display Dual screen Press the or key Press the QB key to show Teletext or Teletext Guide on the right half of the screen Pres
34. nected or if the DVD player has no disc loaded the command can not be executed TheTV or receiver box will then send a play command to the Cinema Link video recorder if present The video recorder will start playing and the audio receiver selects the best Cinema Link sound If no video recorder source is connected or tape is loaded the TV or receiver box will select the last watched TV channel Receiver menu TV DVD Sound Surround Speakers Automatic Manual Give name Reshuffle Recorder installation installation Receiver Setup Demo Install Note W hen Cinema Link is enabled certain items of the Sound menu see TV menu are steered by the audio receiver instead of by the TV or receiver box Press the MENU key on the remote control Press the cursor down to select Receiver Press the cursor right to enter the Receiver menu items Press the cursor up down to select the submenu items Note the audio receiver submenu items may only be selected if provided by the audio receiver dependent on the configuration setup and the sound signals transmitted Sound menu D ependent on the audio receiver speakers configuration you may not be able to select certain menu items Sound Smart Sound Treble Bass Receiver See the Instructions for Use for the TV or receiver box Smart Sound Treble Loudness Bass W hen Loudness On is selected and when listening at low volume the low and high frequen
35. nsmission Mono Stereo is only selectable in case of analogue stereo transmission Nicam Analogue is only selectable in case of Nicam transmission 12 Features menu Features TV Programme list Off Subtitle On Sleeptimer On during mute Child lock On timer Press the cursor right to select Features Select the menu items with the cursor up down and adjust the settings with the cursor left right Use the on screen Menu Info for more information about the menu items Programme list Press the OK key to switch over to the selected TV channel or external Select subtitles The subtitle page must be stored for each TV channel Switch on teletext and select the proper subtitle page from the index Switch off teletext Subtitle On will automatically display them on the selected TV channels if subtitles are in the transmission A symbol will indicate that the mode is on Select On during mute when you want to have the subtitles automatically displayed only when the sound has been muted with the 4 key on the remote control Sleeptimer This sets a time period after which the TV automatically switches to standby Child lock Select Child lock Age lock Lock Lock after Child lock Custom lock Programme lock Unlock Category lock Press the cursor right to enter the Child lock menu You re summoned to enter your code Note You have to re enter your code each time you enter the child
36. nstant record See Record with your recorder with EasyLink p 22 Time display The time is displayed on the screen a 3 Surround mode s Incredible surround With stereo transmission and when Incredible surround is selected it seems as though the loudspeakers are spread further apart from one another Virtual Dolby Surround Optimal with Dolby Surround signals Enables you to experience the effect of Dolby Surround Pro Logic reproducing a rear sound effect See Sound menu 3D effect p 12 Note You can make the same selection in the Sound menu surround mode p 12 E Cinema Go See separate Cinema Link manual p 26 NEXT ViEw On Off see p 14 Freeze To freeze the picture Dependent on the input signal the function may not be possible 0 Active Control 0 D Standby Press to switch the TV off from or to standby mode When switched off a red indicator on the TV lights up N Pixel Plus demo on off Press to switch the Pixel Plus demo on or off In the right part of the screen Pixel Plus is switched on Press longer to display the list of digital options settings Use the cursor up down to select one of the settings See also Picture menu Digital options p 11 E Teletext On Off see p 17 OK Press this key to activate your choice when in the menus to display the progra
37. nt of materials to be disposed of Your contains a tolerated small amount of mercury Please ensure you dispose of your old TV according to local regulations carey DONO EasyLink features are based on the one touch operation approach This means that a sequence of actions are executed at the same time in both the television and the recorder provided both are fitted with the EasyLink function and connected with the eurocable supplied with your recorder Contents 2 Keys the right side of the 2 Use of the remote control RC4301 3 use the 5 Installation 5 Select the menu language and 5 Store lt 6 Automatic installation 6 Manual installation 6 Give name 7 Reshuffle the programme list 7 Select Favourite TV channels 7 TV Setup ei 8 General 8 Source 10 Decoder 10 D mo 10 T MOI e So e om ce Roh ca Roe RR e 11 Picture menu 11 Active Control 12 Sound 12 Features menu 13 nexTView Teletext guide 14 Call nexTView Teletext guide 14 nexTView guides 15 Picture nexTView Teletext guide 15 Teletext Guide 15 Basic functions 16 Acquisition and updating of nexTView information 16 Teletex
38. ntrol repeatedly or select Source the Setup menu see p 10 to select EXT1 EXT2 EXT3 Side or DVI according to where you connected your equipment Remark Most equipment decoder recorder carries out the switching itself when it is switched on Recorder or DVD with EasyLink The recorder or DVD can be operated with Press the MENU key on the remote control the remote control via the Recorder or DVD Select the Recorder or DVD menu with the menu on screen cursor up down Press the cursor left right up down to select Recorder one of the recorder or DVD functions 4 lt gt Rwd Stop Ffw Rec Eject The key for recording can be operated in the TV mode DVD 9 _o _o0 _0 _0 _0 _O If your EasyLink recorder has the system standby 44 gt A function when you press the 1 key for 3 seconds Prev Play Stop Play Next Eject both TV and the recorder are switched to standby Record with your recorder with EasyLink In TV mode it is possible to start a direct recording of the programme which is being displayed on the TV screen Continue to press the record key on the remote control for more than 2 seconds Note Switching programme numbers on your TV does not disturb recording When recording a programme from a peripheral connected to EXT1 EXT3 or Side you can not select another TV programme on the screen without disturbing the recording 22 Au
39. r oppf rt i tabellen Kontakt ditt kabel TV selskap eller din forhandler for n mere opplysninger S Frekvenserna som anv nds i kabel TV n ten kan avvika fr n rekvenserna i tabellen Kontakta ditt kabel TV bolag eller din radiohandlare f r vidare information SF aapeliyhti den k ytt m t taajuudet voivat poiketa taulukossa olevista taajuuksista Tarkat tiedot saat kaapeliyhti sta tai myyj lt GR Ot ovxvottes YOnoMoTOLObVTCL evoioelo elvan va eva Siapogetix s o XupfovAevOsite tnv etaugela mhnoopogies CEI televizi ad llom s sug rz shoz haszn lt frekvenciatar tom nyai lehetnek a t bl zatban k z ltekt l elt r ek is Abban az esetben ha b vebb inform ci kra van sz ks ge forduljon az elad hoz PL Operator sieci telewizyjnej moze stosowa inne cz stotliwo ci ni te kt re figuruj na tablicy bardziej szczeg owych infor macji na ten temat zasi gn u operatora lub sprzedawcy 2
40. resent on the subwoofer Adjust the volume level of the external subwoofer presumed this control is present on the subwoofer See also the instruction manual of the external subwoofer 20 Connect your DVI connector 1 DVI connector allows the following TV and monitor display modes EDTV 640 720 x 480p 720p x 576p HDTV 1920 x 1080i 1920 x 1152i VGA 640 x 480 60 Hz SVGA 800 x 600 60 Hz Select the type of connector of the device DVD STB PC you want to connect with the DVI connector of your TV Connector type YPbPr VGA DVI HDMI Device ES digital stream digital DVD DVD with YPbPr DVD with DVI DVD with HDMI HDTV STB Euro 1080i future future Computer aoe necessary use an appropriate adapter Connector _ type YPbPr VGA DVI HDMI Device digital stream digital Adaptor cable 3 cinch to VGA cable VGA to DVI HDMI to DVI VGA to DVI supplied supplied Connect your device with the DVI connector at the bottom of the TV 1 Connect the audio cable 2 to the AUDIO right and L left inputs of the TV Cinema Link surround receiver See the separate supplied Cinema Link instruction manual p 26 Attention the sound info on screen will not correspond with the actual sound reproduction 21 select connected equipment Press the key the remote co
41. rol the audio receiver instead of the TV The message CINEMALINK ON is displayed on the audio receiver and on the TV N ow the CinemaLink system is activated N ote it is recommended to disable CinemaLink when the receiver is used to record a CD e g or when using headphone when others are watching TV Now you can adjust the initial TV settings for optimal surround sound and install the audio channels before starting up one of the CinemaLink devices The system information about country choice menu language and picture format you set up during the installation of the TV is transferred to the audio receiver automatically TV as centre speaker only in case your TV or receiver box is equipped with a Centre IN connector See the Instructions for Use of the TV or receiver box Setup Source menu Centre input Use the test tone function in the Speakers menu to have a reference of the loudness of the Separate speakers Note If you want the loudspeakers of your TV or monitor to act as centre speaker also connect a cinch audio cable not supplied 2 to the CENTRE connector of your TV or receiver box 1 Activating CinemaLink Continue to press the 5 2 on the remote control for more than 4 seconds TheTV or receiver box sends a play command to the Cinema Link DVD player if present The DVD player will start playing and the audio receiver automatically switches to the best Cinema Link sound If no DVD player is con
42. s the key to switch off Dual screen Active screen selection When in dual screen picture teletext enter the desired page number with the P key then press the MENU key then select the left screen with the blue ball at the top You can now select a compressed or full screen view of picture teletext with the fJ key Press this key repeatedly or press the cursor up down to select another picture format Auto format Super zoom 4 3 Movie Expand 14 9 Movie Expand 16 9 Subtitle zoom or Wide screen Auto format makes the picture fill the screen as much as possible In case of subtitles in the bottom black bar Auto format makes the subtitles visible In case of a broadcaster logo in the corner of the top black bar the logo disappears from the screen Super zoom removes the black bars on the sides of 4 3 programs with minimal distortion When in Movie Expand 14 9 Movie Expand 16 9 Super zoom or Subtitle zoom picture format you can make subtitles visible with the cursor up down Note With signals via the DVI connector less picture formats are selectable S Press the MENU key the remote control to summon the main menu any moment you can exit the menu by pressing the MENU key again Note If you have connected equipment with Cinema Link more menu items are present Picture Sound Features TV Setup cursor to select Demo adjustments Install OK key to Use
43. select a frequency AMP ied VCR timer gt gt fast forward VCR TS search up DVD AMP surround on off CD to select your choice of cursor up down subtitle language DVD to select the next or the RDS news TA AMP previous disc CD to shuffle play CD cursor left right to select a dvd title to select the previous or RDS display AMP following track CD info on screen CD search up down AMP display information Additionally the DVD SAT and CD indicator can be programmed to operate the DVD R SAT RC6 CD R instead Press the Select key repeatedly until no LED is lit To program DVD R press the OK key digit 2 To program SAT RC6 press the OK key digit 4 To program CD R press the OK key digit 6 From now on when the corresponding DVD SAT CD indicator is selected the remote control will operate your DVD R SAT RC6 or CD R Note To return to the modes programmed in the factory either remove the batteries for a few minutes or press the OK key digit 1 DVD mode or digit 3 SA RC5 or digit 5 CD mode 23 Care of the screen Do not touch push or rub or strike the screen with anything hard as this may scratch mar or damage the screen permanently And please do not rub with dust clothes with chemical treatment Do not touch the surface with bare hands or greasy cloth some cosmetics are detrimental to the screen Unplug the TV before cleaning the screen W
44. space such as a book case or a similar To connect your computer see p 21 To connect other peripherals see p 19 If you have a Cinema Link combination Cinema Link Audio receiver and or Cinema Link recorder and or DVD player see the separate supplied instruction manual p 26 In order to obtain the best result please use only the supplied aerial cable between the TV and recorder and between recorder and aerial connector Insert the mains cord supplied into the mains at the bottom of the TV and in the wall socket having a mains voltage of 198 264V To prevent damaging the power AC cord which could cause a fire or electric shock do not place the TV on the cord unit To prevent any unsafe situations no naked flame sources such as lighted candles should be placed on or in the vicinity Avoid heat direct sunlight and exposure to rain or water The equipment shall not be exposed to dripping or splashing Insert the aerial plug firmly into the aerial socket at the bottom of the TV For best picture quality use the suppressor aerial cable supplied Remote control Insert the 2 batteries supplied R6 1 5V The batteries supplied do not contain the heavy metals mercury and cadmium Please check on how to dispose of exhausted batteries according to local regulations Switch the TV on Press the power switch 1 at the right side of the TV An indicator on the front of the T
45. stored in the memory or to assign a name to a TV channel or external for which a name has not yet been entered A name with up to 5 letters or numbers can be given to the programme numbers 0 to 99 and to the externals Q Press the cursor left repeatedly when you have finished the name giving Select another programme number and repeat steps to Reshuffle the programme list You can change the order of the stored TV channels Reshuffle Install Select Reshuffle in the Installation menu Follow the instructions on screen Select Favourite TV channels Favourite programmes Select Favourite programmes in the Install menu Install Select your programme number with the cursor up down Select Yes or No with the cursor right Repeat and for every TV channel or external you want to make a favourite or a non favourite TV channel or external Setup Setup General Setup Menu background Smart surf Factory settings NEXTVIEW provider OSD Programme title Teletext 2 5 Auto surround Subwoofer Set Change code General The Setup menu contains items that control the settings of the TV s functions features services and peripherals you may have connected The General menu allows you to change settings that will typically be accessed only occasionally The Source menu allows you to select a source The Decoder menu allows you to define one or more programme numbers as de
46. t 2 25 RET 17 Switch Teletext and off 17 Select a Teletext page 17 Previously selected teletext page 17 Select the index teletext page 17 Select subpages 17 Picture Teletext 17 Enlarge a Teletext page 17 Hypertext 17 Teletext menu 18 Connect Peripheral 19 Recorder vcr dvd rw 19 Other equipment satellite receiver decoder DVD games etc 19 Side connections 20 Multi channel Surround receiver 20 Connect extra subwoofer 20 Connect your DVI connector 21 Cinema Link surround receiver 21 To select connected equipment 22 Recorder or DVD with EasyLink 22 Record with your recorder with EasyLink 22 Audio and video equipment keys 23 LAUS Ug 24 4 Preparation Wall mounting instructions Table stand According to the type of TV you ve purchased a wall mount bracket and or stand may be supplied How to mount the supplied stand and or wall mount bracket see the supplied separate leaflet Make sure that the wall mount is being fixed securely enough so that it meets safety standards The weight of the TV excl packaging is about 20 kg 32PF9976 42 kg 42PF9956 Note Not supplied stands are optional accessories Consult your dealer Place or hang the TV wherever you want but make sure that air can circulate freely through the ventilation slots Do not install the TV in a confined
47. t possible to display a timed page when in VGA mode Q Press the cursor left to return to the TV menu again Language If the displayed characters on screen do not correspond with the characters used by the teletext broadcaster you can change the language group here Select Group 1 or Group 2 with the cursor right Press the MENU key to leave the Teletext menu Connect Peripheral Equipment There is a wide range of audio and video equipment that can be connected to your TV The following connection diagrams show you how to connect them Note EXT1 can handle CVBS and RGB EXT2 CVBS Y C and RGB EXT3 CVBS DVI can handle VGA SVGA and 480p 576p 10801 and 11521 It is preferable to connect peripherals with RGB output to EXT1 or EXT2 as RGB provides a better picture quality Note If your recorder is provided with the EasyLink function it should be connected to EXT2 to benefit from the EasyLink functionality Recorder VCR DVD RW Note Do not place your recorder too close to the screen as some recorders may be susceptible to signals from the display Keep a minimum distance of 0 5 m from the screen Connect the aerial cables and to obtain the optimum picture quality eurocable 3 as shown If your recorder does not have a euroconnector the only possible connection is via the aerial cable You will therefore need to tune in your recorder s test signal and assign it programme number 0 or store the test signal under
48. the key the remote control Centre input Centre in volume When you have connected a surround receiver to the TV see p 20 the loudspeakers of the TV can act as centre speaker making a separate centre speaker unnecessary Select Centre input On When having selected On you can adjust the Centre in volume with the cursor left right to correct volume level differences of the external audio receiver and speakers Note This is not the case with a Cinema Link surround receiver Select Decoder with the cursor right Select Programme Select the programme number under which you have stored the programme coming from your decoder Select Status Select the input used to connect your decoder None EXT1 or EXT2 Select None if you do not want the selected programme number being activated as a decoder programme number Note Select EXT2 when the decoder is connected to your EasyLink recorder The Demo menu allows to demonstrate the TV features separately or in a continuous loop If Auto demo has been selected the demo will automatically present the features sequentially in a loop Press one of the cursor keys to stop the Auto demo If one of the features has been selected this particular feature demo will run only once and the Demo menu will reappear Note The Dealer demo is not part of the automatic sequence and can only be activated separately Gmm Press the MENU key on the remote control
49. u want to search for Press the OK key to confirm The search starts A message appears at the bottom of the screen to indicate the searching or that the word or page is not found Use the cursor up to exit hypertext 17 Teletext menu Press the MENU key to activate the menu Press the cursor up down to select the menu items Press the cursor right to activate Reveal Reveals conceals hidden information on a page such as solutions to riddles and puzzles Press the cursor right to activate Favourite You may create a list of eight favourite teletext pages in total selected from various TV channels To add a favourite page to the list Select a favourite teletext page Select Favourite in the teletext menu and press the cursor right to enter the list Press the cursor right again to add the page Press the MENU key to watch the current page oo watch favourite page from the list When in Teletext use the P P key to browse through the favourite pages of the TV channel actually selected Note only the pages of the current channel can be selected Search Selecting a word On the keyboard on screen you can type in a random word you want to search for in the teletext pages Whether upper or lowercase is used has no influence WORD NAME FOOTBALL Cancel Accept Delete jm m Space AB ted 6 5 4 1 OP CMR wv e VWXYZ 0
50. ult your dealer Digital distortion The low quality of some digital picture material may be the cause of digital image distortion In this case select the Soft setting using the Picture menu Smart Picture without changing the picture settings manually No sound No sound on any channel Check the volume isn t at minimum Is the sound interrupted with the mute key 7 No solution found for your picture or sound problem Switch your TV off and then on again once Never attempt to repair a defective TV yourself Check with your dealer or call a TV technician NEXT VIEW No NEXT ViEW info See Acquisition and updating of NEXTVIEW information p 16 Displayed time is wrong The broadcaster on programme number one does not transmit the correct local date and time Use Reshuffle in the installation menu to place another broadcaster on programme number one 24 Remote control Check if the remote control is in the correct mode If your TV no longer responds to the remote control the batteries may be dead You can still use the MENU key and the keys on the right side of your TV Standby Your TV consumes energy in the standby mode Energy consumption contributes to air and water pollution Power consumption lt 2 W No stable or not Check if you have selected the correct VGA mode in your PC synchronised VGA picture Miscellaneous See Extras Specifications on this CD
51. ur loudspeakers Centre speaker size d Large Small Subwoofer present is set to No Front speaker size can only be set Rear speaker size amp Large Small to Large If Front speaker size is set to Small Centre speaker size can Distance to front 1 10 m to Small and consequently a subwoofer must be Distance to centre 01 10 Distance to rear 1 10 Distance to the speakers Select the distance from your usual listening position to the available speakers each front centre and rear speakers This defines the delay time for the surround sound Automatic installation installation Automatic install Receiver Install Start Manual installation In the Automatic installation menu select Start to activate the automatic searching of all radio stations which can be received The programme list is automatically filled with all the numbers and names of the radio stations transmitted Manual install Receiver LW Band MW Search SW Preset FM Store AM You can also search for a known radio station by keying in the frequency First select Band to switch to the desired waveband LW MW SW FM or AM Select Search and press the cursor right The frequency increases until a radio station is found If you know the 3 digit frequency enter it directly with the digit keys 0 to 9 Select Preset to enter the preset number using a three digit entry with the digit keys To store your radio station sele

Philips Plasma TV 42" Digital Crystal Clear

Contents

Download Pdf Manuals

Related Search

Related Contents

Philips Plasma TV 42&quot; Digital Crystal Clear

Contents

Download Pdf Manuals

Related Search

Related Contents

Philips Plasma TV 42" Digital Crystal Clear