Belgacom Twist 505 SMS Duo
Contents
1. Blinking the line is busy Loudspeaker en Paging key Press to locate all handsets Using GAP standard compliance The GAP standard guarantees that all DECT GAP handsets and base stations comply with a minimum operating standard irrespective of their make Your Twist 505 515 handset and base station are GAP compliant which means the minimum guaranteed functions are register a handset take the line receive a call and dial The advanced features may not be available if you use another handset than a Twist 505 515 with your base station To register and use your Twist 505 515 handset with a GAP standard base station of a different make first follow the procedure described in the manufacturer s instructions then follow the procedure page 2 to register a handset To register a handset from another make to the Twist 505 515 base station place the base station into registration mode then follow the procedure in the manufacturer s instructions Register a DECT peripheral without keypad Some DECT peripherals such as repeaters do not have a keypad A special menu operated procedure is used to register such peripherals with the base station without the need to disconnect the base station See page 28 to register the peripheral Use the peripheral instructions to register it to the base station 2 Base stations Table of contents Twist 505 515 handset Icons Base stations Twist 505 amp Twist 5152. Using the phonebook VIP settings Adding a name Calling from phonebook Viewing the phonebook Using the call log Viewing the call log Deleting the call log Setting the call log Network Belgacom phonebook Using the Belgacom services Using the extra features Setting the VIP ringer type Setting the call cost and duration Setting the alarm clock Setting the Do Not Ddisturb mode Base Setting the standard ringer type Recording a personnal ringer Setting the ringer volume Setting music on hold Setting the loudspeaker volume Registration Setting the line Setting the Belgacom service codes Troubleshooting Index Oa financial contribution has been paid to the associated national recovery amp recycling system Fo The labelled packaging material is recyclable DECT is a Trade Marks of ETSI registered for the benefit of the implementers of the DECT technology Table of contents Environment and safety Safety information This equipment is not designed to make emergency calls when the power fails An alternative has to be made available to allow emergency calls Power requirements This product requires an electrical supply of 220 240 volts alternating monophased power excluding IT installations defined in standard EN 60 950 Warning The electrical network is classified as dangerous according to criteria in the standard EN 60 950 The only way to power down this product is to unplug the power su
3. Keypad Keys Multi tap Sequence lt gt Press Zs once P space I J amp LS 2 abe2aacae 3 def3 A Press 3 twice Pe 4 shidir 5 jkI5SA Press amp once Pet 6 NTE 7 rs7B 1 0 gt Press 3 J twice Pete 8 9 wxyz9 9 OEY Press 25 three times Peter 0 COR ee a If special characters are included in the text they may not be displayed when reading the SMS The Eatoni system is a new predictive editing system designed to help you write an SMS A little E in the header indicates that you are using the Eatoni mode Eatoni is a word editor that suggests the most probable letter The operation of the Eatoni system is the following Press the key that displays the character you want to edit The character that is most likely to be correct is displayed on the screen If it does not match the expected letter press W to display the next most probable character available on the key To write Peter Enter name til Long press 25 to Enter name Ej Ab with Eatonie Activate Eatoni i Oh j Oh Enter name Ej Ab Enter name E Ab Enter name Ej Ab Press Press 25 to Press Y Pa J OF change character OF 4 0K Press Enter name El b Press Enter name Ej Ab Press Enter name EjAb Pall Pete Peter OK Oh Oh Eatoni amp LetterWise are trademarks of Eatoni Ergonomics Inc Press to validate the name and used by Philips under license 8 Editing sy
4. Navigation reminder I d Goto Validate i Scroll to Gil 4 Select Delete all Settings Using the call log Use to enter the call log The call log stores up to 30 entries a Unanswered calls amp answered calls E messages Twist 515 4 E ME messages PhoneMail outgoing calls local messages or recorded conversation Twist 515 If you have subscribed to the Calling Name Display Service CLIP the call log shows for incoming amp outgoing calls the name or number of the callers the VIP group icon if any the date amp time of the call as well as the number of times they have tried to reach you up to 9 To update the call log the system automatically erases the oldest entry unless there is a message linked to it Then the unread entries Viewing the call log 22 Paula Jameson come 15 040 11 31 Options Cregory Mills Play a000 Gregory Mills ii Store D 00 Gregory Mills ii Delete oaaao To view the call log from the handset l Press 2 The list is displayed scroll through the list to reach the entry validate To call call back or redial from the call log Resume from step amp 2 above 3 Select Call in the options or press To listen to a message from the call log Twist 515 Resume from step amp 2 above 3 Select Play and validate To store the caller name and phone number from the call log Resume from
5. among the 4 options above and validate Note predefined message cannot be deleted Answer machine 15 Recording your personal outgoing message OGM You can record 5 different personal OGM a specific personal OGM for Answer amp record mode for each of the VIP phonebooks Friends Family or Work the standard OGM for Answer amp record mode for non VIP callers and the standard OGM for Answer mode only for all callers It is possible to record a message for a VIP group only if you subscribe to the Calling Name Display service and if you have set the VIP groups in the phonebook See page 21 To record an outgoing message Resume from step l 2 above 3 Scroll to Record Dutgg m554 validate 4 Select a group standard or I of the 3 VIP groups validate 5 Select Record Hew and validate Al K 6 Press to start recording t P Answer machine To stop recording press i again The message is automatically played back You can delete and or record it again The personnal message can be up to 3 mn long Note Select Standard OGM for answer only mode Standard Outgoing Messages OGM for nsw amp record mode if you have no CLI subscription EE E i 51 1 DF 5 Or 550 l OF 359 Outgoing Messages Record outgg mss Record outgg misg 4 Record outgg m55q 2 Press the Pilot key Record outgg m55q ay Family Record new freer a Recording og D0800 O 0 i Start Stop Setting the number of rings before answe
6. 12 19 Backlight 14 Base ringer 25 27 Base stations amp indicators 2 Batteries amp battery life 4 C Call forward 24 Call log 22 23 Call transfer conference call 7 19 Call waiting 67 Calling from call log 6 22 Chain dialling 6 Changing entry name amp number 21 Changing VIP group 21 Contrast 14 Call cost amp duration 25 D Date amp time Set and change 14 Deactivating ringer 2 26 27 Deleting entry 21 Deleting messages answer machine 15 Deleting messages SMS 10 Destination box 9 2 I Direct calling 6 Do Not Disturb mode 26 E Earpiece tone 12 Earpiece volume 7 Ending call 6 Entry type VIP Standard 20 21 External ringer type 1 27 G GAP 2 H Handset keys Handset ringer i Icons I In call features 7 Indicators Base LEDs 2 Indicator handset LED I Installation 4 Internal ringer type 1 27 Intercom 19 K Key amp feedback tones 12 Keypad lock unlock L Language 13 Line settings 28 Listening to messages Answer machine 15 Listening to pre recorded outgoing messages 16 Index Local message Memo 18 Loudspeaker volume 7 27 M Making calls 6 Menu overview Inside cover page Message service Operator voice mail 26 Music on hold 27 Mute 7 19 N Name Add delete change 20 21 Network services 24 28 Notification beeps 12 Number Change 21 O Operator type 28 Outgoing message 16 P Pause PABX PSTN 28 Phonebook 2
7. Call cost amp duration Alarm clock Do Not Disturb mode To set the VIP ringers l Go to Extra validate 2 Select YIP melody function validate 3 Select a group validate 4 Choose a melody validate Note The VIP ringer is heard on both the base amp the handset Call cost and duration Call cost amp duration oaoa View total ao Call cost amp duration Unit cost Od To view the cost amp time l Go to Extra validate 2 Scroll to Call cost amp duration validate 3 Select View total validate The total cost amp time of communications is displayed 4 Press 4 to Reset the counter To allow the phone to calculate the cost of a call you must enter the price per unit Resume from step l 2 above 3 Select Unit cost validate 4 Enter the cost and validate Note The cost of communication is displayed only if you subscribed to the Signal de taxation 16 Khz service The alarm clock Alarm clock 0080 Set time 3 07 00 OK To activate deactivate the alarm clock Fd A long press on activates deactivates the alarm clock with your settings To set the Alarm clock l Go to Extra validate 2 Scroll to Alarm clock validate 3 Scroll to Set the day and select a day validate 4 Set the time and validate When the alarm rings press any key to stop it The snooze is then activated will ring again every 5 mn To definitely stop it press 4 Extra 25 Alarm Clock Settings R
8. GAP Standard Table of contents Installing the Twist 505 Environment and safety Installing the base station Installing and replacing the batteries Battery life and range Introduction Screen in idle mode Understanding the menu system How to navigate in the menus Calling answering a call other principles In call features Editing systems Sending SMS Sending SMS Reading the SMS list SMS settings Handset Setting the standard ringer type Setting the ringer volume Setting the earpiece tone Setting the key amp feedback tones Setting the notification beep Babysit mode Registering an additional handset Using Twist 505 515 handset with several base stations Renaming the handset Changing the language Setting the date and time Setting the display contrast Setting the backlight Using the answer machine Twist 515 Setting the answer machine ON OFF Listening to your messages Deleting messages Sending SMS from the messages list Selecting the answer mode and the outgoing message type Recording your personal outgoing message Setting the number of rings before answer Setting the voice prompts Changeing the voice prompts language Setting the call screening Setting the recording quality Activating the remote control Using the remote control Changing remote control code Recording a local message memo Using the intercom Making internal calls activating babysit mode Transfering a call Using conference call
9. the caller and its VIP group if activated See page 20 To listen to saved messages via the handset l Go to Answer machine validate 2 Select Javed messages validate 3 Select the message to listen validate 4 Choose Play in the options and validate Note You can listen to the message s via the Call log long press on allows to reach the messages list the entry is marked E See page 22 Deleting messages Delete OO00 00 To delete messages Once you have listened to the message you can delete it Resume from step l 3 above 4 Scroll to Delete validate You can also use C on the base station A short press on the key deletes the message while played A long press on the same key deletes all the messages except the unread Warning ffinswerphone full message appears there is no more space for messages Delete messages so that new ones can be left Selecting the answer mode and the outgoing message type You can select among 2 answer modes Answer only when no messagevcan be left Answer amp record when messages can be left For each mode 2 outgoing message types are available predefined or personal message By default the answer machine is set to Predefined Answer amp record mode Answer machine Outgoing Messages 0090 To select the answer mode l Go to Answer machine validate 2 Scroll to Dutgoing Messages validate 3 Select nsw machine mode validate 4 Choose the appropriate mode
10. to Handset validate 2 Select Sounds validate 3 Scroll to Ringer volume validate the current level is heard 4 Choose the appropriate volume and validate Handset li EY Earpiece tone BE EE key amp feedback tones OO0D 0 Sounds Hotification beep OOo To set the earpiece tone l Resume from step l 2 above 3 Scroll to Earpiece tone validate 4 Choose Standard Treble or Bass and validate To set the key amp feedback tones Tones are audio feedbacks heard when pressing the keys amp validating a setting Resume from step l 2 above 3 Scroll to key amp feedback tones validate 4 Select OHSOFF validate To set the notification beep The notification beeps are audio indicators heard when there is a new SMS or a message on PhoneMail Resume from step l 2 above 3 Scroll to Notification beep validate 4 Select OHSOFF validate The babysit mode This feature allows to monitor the baby s room Place the handset in the room to be monitored and you will hear the noise on the additional handset Babysit mode O O00000 Registration To activate deactivate the babysit mode l Go to Handset validate 2 Scroll to Babysit mode validate 3 Select DHSOFF validate An intercom is necessary to monitor the room See page 19 Note You can still answer a call or make a call with the handset Up to 8 handsets can be registered to the base station handset can be associated to 4 base stations Warn
11. 0 2 I Predial 6 R Range 4 Record quality 17 Recording conversation 7 Recording local memo 18 Recording personal outgoing message 16 Redial 6 Registration mode 27 Remote programming Answer machine 18 Remote accessing answer machine 17 Remote Control Code 18 Rename handset 3 Ringers 1 25 27 Rings before answer Answer machine 16 S Screening calls 17 Screen icons Secret access code Answer machine 18 Service codes settings 28 Silence 6 SMS box 9 10 SMS centre 9 I I SMS mode 10 SMS Reading 10 SMS Sending 9 21 22 SMS settings 10 I I Sounds I I 12 27 T Toll saver Answer machine 16 U Unregistering handset 3 Vv Vibra call alert 12 VIP settings 20 21 25 Voice prompts 16 Volume Ringers 12 26 27
12. Belgacom Twist 505 Belgacom Twist 515 User manual belgacem Declaration of conformity We PCE DECT amp Home Telephony Route d Angers 72081 Le Mans Cedex 9 France Declare that the product Twist 505 515 is in compliance with annex Ill of the R amp TTE Directive 99 05 EC and then with the following essential requirements Article 3 1 a protection of the health amp the safety of the user EN 60950 2000 Article 3 1 b protection requirements with respect to electromagnetic compatibility ETSI EN 301 489 6 V1 1 09 2000 amp ETSI EN 301 489 1 V1 3 1 02 2001 Article 3 2 effective use of the radio spectrum EN 301 406 2001 The presumption of conformity with the essential requirements regarding Council Directive 99 05 EC is ensured bb Date 26 11 02 Le Mans Cordless Business Director DECT amp Home Telephony Twist 505 515 Event indicator red Blinking when new SMS or new messages Handset Pilot key Earpiece sd Press to enter the carousel or validate a menu or an option Ef Scroll to navigate in the menus amp options Move the cursor left right Scroll up to reach Intercom from idle mode Scroll down to reach Belgacom phonebook sd A long press to unlock the keypad Loudspeaker Press to take the line or activate the loudspeaker during a call A long press to activate the base loudspeaker during a call Twist 515 Call log A sh
13. ait until it is available Noise interference on your radio The Twist 505 515 base station or Move the base station or power or television mains power pack are too close pack as far as possible to electrical appliances Calling Name Display service Service not activated Check your subscription with does not work network No new SMS are received SMS memory is full Delete old SMS No SMS can be sent The outgoing SMSC number is Contact your operator to get the not set or is wrong correct outgoing SMSC number The SMS box or destinaltion Check the information stored box is wrong page 9 10 21 SMS mode is OFF Set SMS mode ON page 10 Answer machine troubleshooting PROBLEMS CAUSES SOLUTIONS The answer machine does not The memory is full Delete messages record messages The answer only mode is activated Select the Answer amp record mode The Answer amp record is not Press activated The remote control access does The remote control access is not Activate the remote control not work properly activated access page 17 It is not possible to record an The memory is full Delete messages pugorgmesage Twist 515 hangs up during remote 3 failed attempts to send a code Enter the correct code The answer machine stops The memory is full Play amp delete messages A Adding handset 12 13 Adding a name 20 Alarm clock 25 26 Answering calls 6 Answer machine settings 16 B Babysit mode
14. are Friends Family 2 and Work b VVhen ringing the VIP ringer helps you identify the caller s group and the screen shows the caller s name specific welcome message can be associated to a VIP group Twist 515 Subscription to the Belgacom Calling Name Display CLIP sevice is needed Adding a name to the phonebook The names are stored in alphabetical order Kgl To store a name g i 9 et l Go to Phonebook validate Phonebook 2 Scroll to Add mew validate TT 3 Enter the number validate 4 Enter the name validate See page 8 new F A long press on gives direct access to a Enter number Entername Ejabfjenter name Ej Ab Gregory Mills stored 1 OK OK OK Storing a name from predial Once the number is dialled select St re in the options Calling from the phonebook To call from the phonebook Phonebook Press Paula Jameson 044484095765 3 Choose a ig from me list AI Options 4 Choose Lall in the options or press Viewing the phonebook To quickly reach the phonebook press WU To quickly reach a name in the list enter the first character choose from the list if several names start with the same letter Make the call amp 20 Phonebook Change number O O0000 Change name EE Define the YIP group NOD 00O0O Paula Jameson Change sub address EEEE E Paula Jameson Delete 0000da Paula Jameson Send 5M5 oodo Choose SMS Box SMS Box Ei E To vie
15. ate 2 Select Belgacom directory validate 3 You can scroll through the list Note Direct access is possible to the Belgacom phonebook Scroll down 4 the pilot key Services Numbers PhoneMail 1230 1919 1919 Phone Manager 1987 100 112 10I 101 Centre Antipoison 070245245 Antigif centrum 070245245 207 207 1307 1307 1407 1407 Using the Belgacom services Subscription dependent This feature allows to activate or deactivate Belgacom s services Example of service Call forward Calls can be redirected to another phone number Set the code see page 28 and activate it when necessary Operator Services Og Operator Services Call forward S00000000 HMon13 May 02 06 00 Call forwarded View 24 To activate deactivate call forward l Go to to Network validate 2 Scroll to Operator Services validate 3 Select Call forward validate 4 Enter or choose from phonebook the number to which the calls are to be forwarded and validate 5 The number is automatically chained to the call forward prefix and the system dials the number 6 Hang up From now on the calls will be redirected to the assigned phone number The display shows the information To stop call forward deactivate it via the Cancel option Network al Extra VIP melodies i 95 a VIP Melody Function 000 Navigation reminder 16 Goto Validate fil Scroll to Gil 4 Select VIP melody function
16. coocoo oooo ao Press Scroll Press to Press to Press to Press to see to select up or down select select select the list of melodies amp listen Introduction 5 Basic principles Making a call Predialling Direct dialling l Dial from keypad l Connect the line A To correct a digit use amp 2 Dial from the keypad 119456 2 Make the call A5 ed ei Talk to the other party Options Talk to the other party Options 3 Hang up 3 Hang up amp Calling from phonebook ad g l 4 to enter carousel 2 G4 to reach the phonebook menu oa E Phonebook 3 4 to select the menu 4 ci to reach the name Phonebook n 5 Choose Call in the options or make the call V ig Note You can also press to directly reach the phonebook Options Answering ending a call When the phone rings press AA to answer the call Extarnalcall amp Paula Jameson To stop the phone from ringing without answering press 4 to select silence Hence Calling from the call log Redial or call back last caller FFE To redial a number through the call log press and select from the list Zem 145 04 14 34 4 Options Press 4 to enter the options and select Call or directly press To chain dial predial mode You can chain dial 2 numbers One predialed and the other one from the phonebook or the call log or both from the phonebook 977 Options l Predial the number for example operator prefix 2 Use or t
17. e validate Navigation reminder 101 Goto Validate i Scroll to Gi 4 Select Answer machine Saved messages Record memo Outgoing messages TAM Settings Using the answer machine Twist 515 Setting the answer machine Set the answer machine to allow callers to leave messages You can access the answer machine either from the base station or the handset By default the answer machine is activated It can store up to 30 messages on the answer machine within the maximum recording time of 20 mn message can be up to 3 mn long Ei 6 To switch the Telephone Answer Machine ON OFF a From the handset j _ l Go to Answer machine validate 2 Scroll to TAM Settings validate Answer machine TAM Settings 3 Select M de validate Mode 4 Select DHSOFF validate 00000 From the base station a long press on activates or deactivates the answer machine Once activated the red indicator is lit 14 Answer machine Listening to your messages You can listen to new or saved messages via the handset or the base station Mon 44Hov 07 14 23 12 View Answer machine saved messages 000 To listen to the new message s via the handset The display shows there is new message 4 E l Press 4 to Yiew 2 The message is automatically played Note The entry shows the number of times the caller tried to reach you If you have subscribed to the Calling Name Display Service the display shows the name of
18. e in the options To listen to a saved memo on the handset _ l Go to Answer machine validate dene 2 Select Saved messages validate Play 3 Select Play validate O00000 A long press on to reach directly the messages list Answer machine Navigation reminder 16 Goto Validate fil Scroll to Gil 4 Select Intercom Li Call all Handset list Using the intercom If there are at least 2 handsets This feature allows you to make internal calls use the babysit room monitoring transfer external calls from one handset to the other or use the conference call option The intercom is possible with handsets registered to the same base station ave Intercom Call all i Call al 9 VExternalcall fi Paul 6 07 43 Options Intercom BIE EE E belgacom Call Call ended Call transfered Options Conference call EIEE E Internal call or room monitoring activation l Go to Intercom validate 2 If there is one additional handset it rings automatically otherwise select from the list the handset you want to call validate 3 The called handset rings 4 Take the line AN on the called handset The intercom conversation room monitoring can start Mute is also available Note You can also access the Intercom with the pilot key In idle mode scroll up 4 Call transfer During an external call you can transfer the call to another handset via the Intercom optio
19. en nobody will be able to reach you Set day Start time stop time Allowed caller choice Tuesday 08 00 49 00 d Family o ooo000000 40 0K 0k mi m Extra Navigation reminder Base station Sounds cl 58904 164 Goto Validate fil Scroll to Gil 4 Select Registration Line settings Service code settings Setting the base station Setting the base station sounds To set the ringer type l Go to Base validate Base 2 Scroll to Sounds validate 7 3 Select Ringer type validate i FER 4 Choose External standard ringer validate 5 Choose the ringer in the list and validate O000 To record a personal ringer Twist 515 Resume from step l 2 above 3 Scroll to Record pers melody validate 4 Select Record new melody validate Record pers melody 5 Press 4 to start recording mi mm 6 Press again to stop recording 7 Select this melody in the previous setting To set the ringer volume level Resume from step l 2 above Ringer volume 3 Scroll to Ringer volume validate nogo 4 Select the appropriate level and validate To activate deactivate the music on hold This feature allows the caller to hear a music when the call is put on hold when transfering a call from one handset o another See page 19 Music on hold Resume from step l 2 above G00 0 3 Select Music on hold validate 4 Select OH DFF validate Note If the feature is deactivated the caller will hear beeps To set the base loudspeaker vo
20. er volume O 000 To change the password select an SMS box and choose Change password If you lost your password delete the corresponding box Choose Delete confirm your choice and validate Warning When an SMS box is deleted so are the attached SMS To set the SMS centre number s The SMSC is the centre through which the SMS goes to reach the receiver To receive SMS from another operator you must set the corresponding number l Enter Incoming number validate 2 Enter Outgoing number validate Handset Sounds Babysit mode Registration Rename handset Languages Date amp time Display contrast Backlight Navigation reminder 10 Goto Validate i Scroll to Gil 4 Select Setting the handset sounds The ringers can be set for The external standard ringer for callers whose number is not stored in the phonebook or stored with no VIP settings The internal ringer for intercom if there are at least 2 handsets To set the 3 VIP ringer types Friends amp Family amp amp Work l see page 25 Calling Name Display service needed Please contact your network operator To set the ringer on the handset l Go to Handset validate 2 Select Sounds validate 3 Select Ringer type validate 4 Choose External Standard ringerfInternal ringer validate 5 Select the ringer in the list and validate To set the volume level There are 5 ringer volume levels plus the vibra call alert l Go
21. ernal call other in call features are available such as Switch and End intercom To switch the loudspeaker ON OFF Press to activate deactivate the louspeaker on the handset A long press activates the base loudspeaker Twist 515 To increase decrease the handset earpiece or loudspeaker volume during a call Scroll the pilot key up or down 4 on the side of the handset CLI Call waiting If you subscribe to this service a beep in the earpiece informs you of a second incoming call The name or the number of the second caller can be displayed if you also subscribe to the Calling Name Display service To answer the second call use 2 In call features 7 Editing systems Capitalisation By default the first letter of a sentence is in upper case Use to change the case mode all characters in upper case AB or all letters in lower case ab Punctuation and mathematical marks are available through while other special characters are available on 3 Scroll to G4 move the cusrsor left or right Press to delete a character a long press deletes the whole text Twist 505 515 uses two editing systems Multi tap and Eatoni Make a long press on 2 to switch between both systems Lest s compare both systems to write Peter The standard multi tap system allows you to enter the text character by character pressing the corresponding key as many times as necessary to reach the desired character To write Peter with multi tap
22. ess the menu Belgacom Menu Hon 44 Hov 02 49 00 Missed calls Pi new SMS or new messages Fz answer machine or wie 2E tE PhoneMail if any are displayed in idle mode The pilot key 4 on cm the side of the handset gives access to the corresponding menu Hew eventis Fri 22 Hov 02 45 40 Belgacom Menu fi Do not disturb mode Wf and the alarm clock EJ if activated are also displayed on the idle screen To modify these settings use amp on the keypad Understanding the menu system ete To access the carousel menu from idle screen press 4 on the side of the handset The carousel represents a loop of icons that gives access to the different hands first level menus Scroll up or down ed to reach the desired menu Press sd to validate finger type The sub menus are listed and represented by little squares LI at the bottom of the display To reach one particular sub menu use the pilot key G4 and press 4 to validate your choice External Standard Ringer l A tick i shows the selected sub menu or option The shows the option you are browsing Note Certain menus are also directly accessible via a dedicated key on the keypad example Phonebook Call log D Example of navigation in the menus To reach the ringer type menu Fri 4 Mov 02 44 34 m ENT Sounds Ringer type External Standard Belgacom i ed fu J Sounds sp Ringer type spd Ringer Menu Handset
23. fore seeing symbols on the display Allow the handset to charge for 24 hours In case you need to change the batteries the following type is mandatory R03 AAA NiMh 600 650 mAh Warning It is advisable to plug the base station into the mains when charging Always use rechargeable batteries Battery life and range The battery life is about 250 hours in stand by time when the handset is in idle mode amp ready to receive a call and around 16 hours in communication battery low alert will inform you that the handset has to be recharged if this is during a call the call will end shortly after the alert Optimal battery life is reached after 3 cycles of full charge discharge Under ideal conditions the range is a maximum of 50 metres indoors and 300 metres outdoors When reaching the range limit the conversation will become crackly move closer to the base station otherwise the call will be cut off To reach optimal range place the base station away from electrical appliances 4 Environment amp Safety Twist 505 515 handset language is English Select the appropriate langauge before setting the phone l Go to Handset validate Language 2 Select Language validate ooco cd 3 Choose your language validate The screen in idle mode In idle mode Twist 505 display shows different information Fri 4 How 02 44 34 In normal idle mode the display shows the date amp time the name of the handset and the instruction to acc
24. ing PROBLEMS CAUSES SOLUTIONS yu RE green indicator does not light ANE JE base station is not properly un mains power and connected connections The ffm does not scroll when Bad contact Move the handset slightly the handset is placed on the base Dirty contacts Clean the contacts with a cloth moistened with alcohol No dialling tone No power Check connections You are too far from the base Move closer to the base station station No ringer The ringer is deactivated Set the ringer page 1 26 27 The Do not Disturb mode is ON Deactivate it The Y does not appear No mains power Check connections The handset is too far from the Move closer to the base station base station Hatching on the line You are too far from the base station Move closer to the base station The base station is too close to and check the range electrical appliances reinforced Move the base station to find a concrete walls or metal doorframes better place the higher the better The handset displays failed The procedure to add a handset Disconnect and connect the when attempting to add another has failed try again base station power supply Follow handset to the base station Maximum number of handsets the procedure to register a When using a handset has been reached handset page 12 Base station is already busy with Un register a handset page 3 another handset ie Phonebook W
25. ing If you wish to associate non Philips handsets to the Twist 505 515 base station make sure that this handset is GAP compliant otherwise it will not operate properly see page 2 Welcome Register handset Enter RC code J OK To register an additional handset l Unplug and plug back in the mains lead to put the base in registration mode 2 With the additional handset press 4 to start the registration 3 Enter the the 4 digit RC code written on the sticker placed under the base station If successful the additional handset will be named amp numbered The attached digit is linked to the registration order Handset EY Registration Un register handset 090 To un register the handset l Go to Handset validate 2 Scroll to Registration validate 3 Select Un register handset validate 4 Choose in the list the handset to un register validate 5 Enter the RC code 4 digit code and validate Note We advise you to un register a defective handset before returning the product to the repair centre Using the Twist 505 515 handset with several base stations Each Twist 505 handset can be used with up to 4 base stations To use a handset with another base station the handset must first be registered to that base station see page 12 Registration Base selection 108 When you want to call through that base station l Go to Handset validate 2 Scroll to Registration validate 3 Select Base selection va
26. inger type rm Alarm Clock Settings Ringer volume Og To set the alarm ringer type l Go to Extra validate 2 Scroll to Alarm clock validate 3 Select Alarm Clock Settings validate 4 Scroll to Ringer type validate 5 Choose among the available ringers and validate To set the alarm ringer volume Resume from step 3 above 4 Scroll to Ringer volume validate 5 Choose among the available volume levels and validate Do Not Disturb mode This feature allows you to screen calls after a certain time in the evening Enter the time period and select the VIP group s allowed to call you If the caller does not belong to an allowed group the handset amp base station will remain silent The green light informs you of an incoming call The caller will hear ringing and the call could be rerouted to the answer machine Twist 515 if it is ON or to the PhoneMail Do Hot Disturb mode 000a 26 To activate deactivate Do Not Disturb mode 7 A long press on activates deactivates this mode with your own settings To set the Do Not Disturb mode l Go to Extra validate 2 Scroll to Do Hat Disturb mode validate 3 Select B k day and select a period of time 4 Scroll to Start time and set the time validate 5 Scroll to St p kime and enter the time validate 6 Select and activate the allowed callers group s and validate Note You can select up to 4 groups If no group is selected but the feature is activated th
27. lect the SMS from the list 5 Scroll to Reply validate Follow instructions from step 7 page 21 Send SMS from the phonebook To forward an SMS Resume from step l 4 above 5 Scroll to Forward to phone validate Follow instructions from step 5 page 9 Send SMS to a phone To copy the phone number to phonebook Resume from step 4 above 5 Scroll to Copy to phonebook validate 6 Enter the name validate 7 The number is automatically stored To call from the private SMS Resume from step l 4 above 5 Scroll to Call or connect the line CAA Options are commonly available for both SMS sent from a phone and an E mail The options are Yiew SM5 iew number Send again and Delete 5M5 Bobby Delete SMS EEEE E SMS settings SM5 Settings Mode 000 5M3 Boxes O 00 Add new D To reach these options Resume from steps l 4 above 5 Select the appropriate option and validate Follow the instructions on the screen To set the SMS mode The default mode is ON If you wish to no longer receive SMS deactivate the feature To create your SMS boxes l Go to SMS validate 2 Scroll to SMS Settings validate 3 Scroll to SMS boxes validate 4 Select Add new validate 5 Enter the box number between I amp 9 validate 6 Enter the password twice validate password not compulsory SMS EY Edit incoming number OK Edit outgoing number Ok EV EN e g E Handset Ringer type 0000 Ring
28. lidate 4 Choose the base from the list and validate Warning The handset will automatically operate with the last base station to which it was registered If the handset is out of range it will automatically search for another base station from the list Renaming the handset Rename handset OO0 0000 To rename a handset l Go to Handset validate 2 Scroll to Rename handset validate 3 Change the name and validate Changing the language Language NOOO 00O To change the language l Go to Handset validate 2 Scroll to Language validate 3 Select the language and validate Warning Changing the language wil not change the voice prompts of the answer machine Setting the date and time This feature allows to set the system to the right date amp time It is also used to date the messages and all events in the call log Date amp time OODODOD DO To set the date and or the time l Go to Handset validate 2 Scroll to Date time validate 3 Choose S E date or Set kime validate 4 Enter the current date or time and validate Handset 13 Setting the display contrast To set the contrast l Go to Handset validate 2 Scroll to Display contrast validate OOOOO0 3 Select the appropriate level and validate Display contrast Setting the backlight To set the backlight l Go to Handset validate Backlight 2 Scroll to Backlight validate OODO0008 3 Select the duration or deactivate the featur
29. lume sounds Loudspeaker volume OoO00d Resume from step l 2 above 3 Scroll to Loudspeaker volume validate 4 Select the appropriate level and validate Base station 27 Registration This feature allows to register a DECT peripheral without keypad Base Station Enable registration D DO The line settings Line settings Hetuork type au Line settings First ring Og To register the DECT peripheral l Go to Base station validate 2 Scroll to Enable registration validate 3 Enter the peripheral code validate 4 Follow the instructions of the peripheral manual see page 2 To change the network type Resume from step l 2 above 3 Scroll to Hetw rk type validate 4 Select PS TH PABH and validate Note The default setting is public PSTN To activate deactivate the first ring To prevent the phone from ringing when receiving an SMS the first ringer is deactivated You can activate it Resume from step l 2 above 3 Scroll to Arst ring validate 4 Select Activate deactivate and validate Belgacom service code settings If you subscribe to extra services with Belgacom you may need to set some codes in your phone Base Station service code settings omiga 28 To change a service code l Go to Base validate 2 Scroll to Service code settings validate 3 Select the appropriate service validate 4 Select Change and enter the new code and validate Base station Telephone troubleshoot
30. n available in the in call options l press 4 2 Scroll to Intercom validate 3 If there is one additional handset it rings automatically otherwise select from the list the handset you want to call and 4 Call The called handset rings The external call is put on hold If there is no answer from the second handset you can resume the call on the first handset use the End Intercom option 4 Take the call AN on the other handset Both internal callers can talk 5 Use the Transfer option in the menu The call is ended on the first handset The display gives the feedback Note You can also stop the call on the first handset with VI When the call is put on hold the caller hears music if music on hold is activated or beeps See page 27 Conference call Conference call allows one external call to be shared with 2 handsets in Intercom The 3 people can share the conversation No operator subsciption is needed Resume from step 4 above 5 Use the Conference Call option validate Intercom 19 Navigation reminder 164 Goto Validate fi Scroll to Gi 4 Select B l Phonebook f View Add new Using the phonebook common to all handsets 100 names and numbers can be stored in the phonebook The phonebook contains all the information related to the callers especially the VIP settings The names and numbers are shared with all the handsets registered to your base VIP settings The VIP groups
31. o open the call log or the phonebook Te 3 Scroll G4 through the list 044484093765 4 Options 4 Select an entry and validate 4 You can move the cursor l erase or change a digit with Calling 9770444184093 765 5 Connect the line A Note It is possible to chain dial in direct dialling mode You can also 4 Options retrieve numbers from the SMS list 6 Calling answering a call other principles In call features During an external call you can access additional features available in the in call options Press 4 to enter the Options To mute the handset microphone l Press 4 Mute 2 Scroll 4 to Mute and validate 4 a00 The caller can no longer hear you To resume the conversation press again 4 to Unmute Options Intercom if there are several Twist 505 515 handsets Intercom During a call you can put a call on hold transfer an external call or share Nan the conversation on conference call I external caller 2 internal callers See page 19 To record a conversation Twist 515 l l While on line Press 4 2 Scroll to Record and validate 4 Record The call is recorded for a maximum of 6 minutes on the answer machine ooa To continue recording resume from step above To listen to the conversation use the Call log menu or the messages list The entries are marked EJ Warning Recording a conversation may be illegal We advise you to inform the person you are calling During an int
32. ort press to access the call log A long press to directly access the vocal messages list Twist 515 Z Keypad lock amp Editing A short press to insert A long press to lock unlock the keypad in idle mode A long press to enter multitap or D Line key Press to take the line answer a call or hang up Correct key To correct a digit when predialling or a character when editing A short press to go back one menu when navigating A long press to return to idle mode when navigating To insert R for operator services when on line Phonebook A short press to access the phonebook A long press to add a new entry Do Not Disturb amp case mode A short press to insert when dialling A long press to activate deactivate the Do Not Disturb mode A long press to insert a pause P when dialling Press to switch case mode when editing Alarm clock A short press to dial 0 A long press to activate deactivate the alarm clock Eatoni editor when editing Microphone treaty By ea ee Icons Steady ON Blinking Fast blinking Answer machine ful Twist 515 I New message on answer machine Twist 515 or PhoneMail Answer machine ON Twist 515 Incoming external call in progress Line is already busy External call in progress Internal call in progress Internal incoming call Handset loudspeaker ON Base loudspeaker ON Twist 515 Ringer deacti
33. ple Phone SMS sub address 0 Phone 2 SMS sub address 3 When a sender sends you an SMS from a GSM he must add the sub address of the SMS box to which he wants to send it Example 02 202 41 11 0 or 02 202 41 II 3 If he does not add that digit Belgacom will send automatically the SMS to box 0 that is why we advise you to always use sub address 0 in one phone the default sub address is 0 zero Sending new SMS To send an SMS to a phone SMS Box l Go to 5M3 validate aao 2 Select Send new S S5 validate 3 Choose your SMS box amp enter the password if you created several SMS boxes validate 4 OK 4 Dial the number you can use the call log or the phonebook validate 5 Enter the sub address of the receiver validate 6 Input the text see page 8 7 Select Send How validate Ok Reading the SMS list Private SMS are the sent saved and received SMS The received SMS are shown by and the saved SMS are shown by Fl When reading the list of SMS some options are only available for SMS sent from a phone Those options are Reply Forward Copy to phonebook and Call SMS 9 t3 Choose SMS Box SM5 Box OO O0000 Bobby Forward to phone OOO O000 Bobby Copy to phonebook doood Bobby Call O0000008 To reply to a new SMS l Go to SM5 validate 2 Scroll to Read SM5 validate 3 Choose your SMS box amp enter the password if you created several SMS boxes validate 4 Se
34. pply from the electrical outlet Ensure the electrical outlet is located close to the apparatus and is always easily accessible Telephone connection The voltage on the network is classified as TNV 3 Telecommunication Network Voltages as defined in the standard EN 60 950 Safety precautions Do not allow the handset to come into contact with water Do not open the handset or the base station You could be exposed to high voltages Do not allow the charging contacts or the battery to come into contact with conductive materials 1 Environmental care Please remember to observe the local regulations regarding the disposal of your packaging materials exhausted batteries and old phone and where possible promote their recycling Installing the base station To properly install the base station plug the line cord and the power cable to the base station Plug the cord and the cable into the wall The green led on the base station and a beep indicate that the phone is properly installed A Warning Always use the cables provided with the product 1 Do not insert any thing in this opening Installing and replacing the batteries To insert the batteries open the battery cover place the batteries as indicated and put the battery cover back When the handset is placed on the base station the 3 battery bars scroll if charge is needed On first charge it may be necessary to wait for a few minutes be
35. propriate language Setting the call screening This feature allows you to hear the callers leaving a message You can set permanent call screening on the base station TAM Settings To activate deactivate the call screening Call screening Resume from step l 2 above oo00 00 3 Scroll to Call screening validate 4 Select a volume level or deactivate the feature Silence Call screening call by call on the handset is also possible While the caller is leaving a message press rd to listen and press 4 again to stop listening Adjust the volume with f Setting the recording quality There are 2 recording qualities standard and high In standard quality the total capacity is 20 mins To set the recording quality Resume from step l 2 above 3 Scroll to Recording quality validate OOO008U 4 Select the appropriate settings and validate TAM Settings Recording quality Activating the remote control The default setting is OFF To activate deactivate the remote control feature TAM Settings Resume from step 2 above Remote control 3 Scroll to Remote control validate oococco 4 Scroll to M de validate 5 Select GQHSOFF and validate Remotely control your answer machine To remotely access your answer machine l From another phone dial home 2 During or after the msessage press the star key on the handset 3 Dial your remote control code 4 If you have new messages they will be automatically played Ans
36. r You can set the answer machine to start playing the outgoing message after a given number of rings 3 5 7 and Toll saver The toll saver option activated by default is useful when using the remote access The answer machine will start playing the outgoing message after 3 rings if there are new messages If there is no new message the outgoing message will be played after 5 rings Hang up after the 4th ring to check if there are new messages at no cost To set the number of rings before answer rs l Go to Answer machine validate helia ake Urd 2 Scroll to TAM Settings validate l o ooo000 3 Scrollto Humber of rings before answering validate 4 Select the appropriate setting and validate Setting the voice prompts Voice prompts are vocal indications played when consulting the answer machine By default they are activated You can set them to indicate the number amp date of the messages or the number of messages only You can also deactivate them The default language of the voice prompts is English You can modify it 16 Answer machine To set the voice prompts TAM Settings l Go to Answer machine validate Voice prompts 2 Scroll to TAM Settings validate oo ocadc 3 Scroll to oice prompts validate 4 Select the appropriate settings and validate To change the Twist 515 answer machine voice prompts language Ut settings Resume from step l 2 above Voice language 3 Scroll to Yoice language validate Mmm 4 Select the ap
37. stems Navigation reminder 164 Goto Validate fil Scroll to Gil 4 Select Li SMS Text messages Sending SMS Read SMS SMS settings With your Twist 505 515 you can send and receive text messages of 160 characters SMS Short Message Service With Belgacom SMS service you can send SMS to a fixed or mobile phone On SMS enabled devices GSM PC phones the SMS is received as a text message If the receiver of your SMS has no device compatible with that service the message is received as a vocal message When sending an SMS your phone number is always sent to the receiver Conditions To receive SMS you must subscribe to the Affichage du num ro service from Belgacom To send and receive SMS the outgoing SMS centre number 1717 and the incoming SMS cnetre number 01717 must be set in the phone see page 1 These numbers are set by default in the phone you can send SMS with no additional setting To send and receive SMS you must set the SMS box sub address The default box is 0 See page 21 To receive SMS your phone number is to be registered with Belgacom SMS service You can contact the nearest T l boutique the customer service 0800 33800 or call 0800 17173 To receive SMS a sub address is to be associated to your phone number This notion of SMS boxe sub address can be compared to letter boxes belonging to different houses The sub address can be choosen between 0 and 9 Exam
38. step amp 2 above 3 Select Store validate 4 Enter the name validate To delete an entry from the call log Resume from step amp 2 above 3 Select Delete validate 4 Confirm your choice and validate Warning If a message is associated to the entry it is also erased from the answer machine Call log Gregory Mills send 5M5 COU E To send an SMS from the call log Resume from step amp 2 above 3 Scroll to Send SMS validate Follow the instructions from step 4 page 21 Send SMS from phonebook Deleting all the call log Delete all Ei E To delete all the call log You can choose to delete all the call log at once l Go to Call log validate 2 Scroll to Delete all validate 3 Confirm your choice and validate Note Entries with unread messages will not be deleted Twist 515 Setting the call log You can set the call log to store information about incoming calls and or outgoing calls Call log Call log Settings 108 Incoming calls r To set the call log l Go to Call log validate 2 Scroll to Call log Settings validate 3 Select Incoming calls Outgoing calls validate 4 Select the appropriate setting and validate Call log 23 Network o Belgacom phonebook Belgacom Services N avigation reminder 16 Goto Validate i Scroll to Gl 4 Select Using Belgacom phonebook Belgacom directory rm To read the Phonebook l Go to Hetwork valid
39. vated SMS function ON New SMS SMS memory full 985 fi Registered amp in range of Not registered the base Fy i Alarm clock amp or Do not disturb mode activated NINN The battery symbol When charging the battery bars scroll uo my Gp When the handset discharges the battery shows the status Full mmp 2 3 gt 1 3 0 and empty L gt Twist 505 515 handset i Twist 505 Power indicator green Base station gt ON System well connected to H the mains Event indicator red OFF System not powered IN Blinking New events Blinking the line is busy new SMS missed calls etc Fast blinking SMS Memory full a e Twist 50 C Paging key Press to locate all handsets Twist 5 5 Answer machine indicator red Base station f x Delete key Press to delete current message Long press to delete all the messages except unread ones ON Answer machine activated OFF Answer machine deactivated Blinking New messages Fast blinking Answer machine memory full gt n ma ON OFF key Power indicator green Press to play or stop the messages Long press to switch answer machine ON OFF ON System well connected to the mains Twist 515 OFF System not powered
40. w the phonebook l Press 3 Browse the list G4 and select a name validate To change a number Resume from step amp 2 above 3 Select Change number validate 4 Enter the new number and validate Note It is possible to erase the current number with es You can simply change a digit move the cursor 4 to reach a place To change a name Resume from step amp 2 above 3 Select Change name validate 4 Enter the new name and validate Note It is possible to erase the current number with es You can simply change a letter move the cursor Qd to reach a place To define VIP group To benefit from the VIP feature you must store the entry in a VIP group Start from step 1 amp 2 above 3 Select Define the YIP group validate 4 Select the VIP group and validate To set an SMS sub address to a name Resume from step amp 2 above 3 Select Change sub address validate 4 Enter the sub address validate To delete a name Resume from step amp 2 above 3 Choose Delete and validate To send an SMS from the phonebook Resume from step amp 2 above 3 Select end SM5 validate 4 Choose your SMS box amp enter the password if you created several SMS boxes validate 5 Enter the sub address of the receiver if prompted validate 6 Select Haw SMSSSMS list validate 7 Imput the text See page 8 or browse through the list validate 8 Select Send How validate Phonebook 21 gt Call log View
41. wer machine 17 The following table indicates the features available when remotely accessing the answer machine dial dial dial Deactivate answer machine dial Record memo Delete dial dial La dial Read previous message Activate answer machine Play message Stop dial Listen again to the message dial 3 Read next message To change the remote control code The default code is 0000 We advise you to personalise it ae FP l Go to Answer machine validate 2 Scroll to TAM Settings validate ua 3 Scroll to Remote control validate 4 Scroll to Change code validate 8963 5 Enter the new remote c code and validate 4 0k Warning The Remote Control code is not the Registration Code RC Recording listening to a local message Twist 515 This feature allows to leave local messages for your family on the answer machine A memo is recorded from the handset it is represented by E3 in the call log and can last up to 3 mins To record a memo on the handset Record amemo l Go to Answer machine validate naon 2 Scroll to Record a memo validate 3 Press 4 to start recording Press the Pilot key 4 You are informed that the memo has been properly recorded to record J Start Hon 44 Mov 0 14 23 To listen to a new memo on the handset The display shows there is I new local message 1 EJ l Press 4 to View 1E 2 The message is automatically played Vien Delete is availabl
Download Pdf Manuals
Related Search