Transcend Internal Multi-Card Reader
Contents
1. Removable Disk G Removable Disk I To Use with Linux Kernel 2 4 or Later The Internal 6 in 1 Card Reader is a driver free device for Linux kernel 2 4 or later Just follow the procedures below to mount and use it 1 Power on the computer and insert a memory card into the Internal 6 in 1 Card Reader 2 Create a directory for the Internal 6 in 1 Card Reader Example mkdir mnt CardReader 3 Mount the Internal 6 in 1 Card Reader Example mount a t msdos dev sda1 mnt CardReader No matter how many memory cards are inserted into the Internal 6 in 1 Card Reader only the slot with first inserted memory card can be mounted To Safely Remove Memory Cards To Remove in Windows Make sure that the LED is not blinking no data are being transmitted You can then safely remove the memory card WARNING Removal of a memory card directly may cause the system to halt To Remove in Linux Unmount the device from the Linux environment You can then safely remove the memory card Example umount mnt CardReader WARNING Never remove or insert a memory card while data are being transmitted To avoid improper shutdown open the transmitted file from its new location to ensure transmission has been completed Boot up Function The CompactFlash slot of the Internal 6 in 1 Card Reader can be configured as a bootable drive To enable the Boot Up function your motherboard must support USB boot up de vices Upon comp2. match the default setting of USB connector shown above rearrange the color wires of the USB cable as follows a Use a needle to raise the small plastic tab and pull the color wires out of the connector Be careful not to break the tab M y A p 4 b Refer to the pin assignment of USB connector as below and to realign the color wires VVIl vc 5SiIian en P Data WARNING Be careful in realigning the color wires Any error here will cause serious damage to the Internal 6 in 1 Card Reader c Keep the same side of wire pins facing up and insert them back into the con nector Press the tab down to fully seat the wire pins 6 Connect the USB connector of the Internal 6 in 1 Card Reader to the USB pin header on the motherboard Hardware setup is complete To Use the Internal 6 in 1 Card Reader After the driver installation and hardware setup are complete you can power on the com puter and start to use Internal 6 in 1 Card Reader To Use with Windows 98SE Me and 2000 1 Power on the computer The New Hardware Found window appears the first time you power on the computer after installing the Internal 6 in 1 Card Reader 2 New Hardware Found USB Storage Drive Windows is installing the software for your new hardware Four Removable Disk drives with newly assigned drive letters appear in My Com puter The Internal 6 in 1 Card Reader is ready for use 2m Ele Edit View Favorites Toole H
3. FDD Generic STORAGE DEVICE for the 1st Boot Device then press ESC Hoot Device Select setup Help BS IDE 8 UDC end IDE 1 H X Disabled ET CDROM PLE IDE B UDC UD48BDD BBDEAG Try Other Boot Devices IDE 1 NAXTOR 6104012 Floppy 1 44 HE 34 CDROM PLEXTOR CD R PX Wi210A BBS Network Intel UNDI PXE 2 8 build 67 USB RMD FDD Generic STORAGE DEVICE F1 Help Ti Select ten r Change Values F Setup Defaults Fer iPrey s Henu Enter Select Foub flenu F5 Hi Perfornance 8 Choose Save amp Exit Setup to save the new configuration to CMOS and exit the CMOS Setup program At SAVE to CMOS and EXIT Y N Type Y and press Enter 9 Reboot your system 11 Specifications Power SUDDIV i ti ctio ERO E bata ts DC 5V from USB port Slots for storage media CompactFlash Card Type I II IBM Microdrive omartMedia Card Secure Digital Card MultiMediaCard Memory Stick PRO Operating Temperature 0 C 40 C Storage Temperature 10 C 60 C FUMA IY eL 0 90 RH Emission Safety cia aia aia FCC Class B CE BSMI DIMENSIONS E 154mm x 102mm x 26mm B 315g 12 Card Reader Limited Warranty Above and beyond is the standard we set ourselves for customer service at Transcend We consistently position ourselves to be significantly above the industry norm It s all part of our commitment to Customer Satisfa
4. USB 2 0 Internal 6 in 1 Card Reader User s Manual P N TSOMFLRD6E Transcend Your Supplier Your Partner Your Friend Table of Contents Introduction PACKAGE Contents soo sni v Pp em Ia uM C I D UT PM I s IPLA IUE 1 EDAD IDEE E TTE TOUT TOO TEE UTE 1 System Requirements mci oca ers dde bara pevnkQs SveoU Ege D PUUS dns Een ERE FRE Dra a DR C DET Ora Era DUC FRISE DRE 1 Driver Installation Driver Installation for Windows 98SE Me and 2000 eere 2 Driver Installation for Windows XP Linux Kernel 2 4 or Later 4 Hardware Setup 1 eerte tte tremere ttt stl sts as 4 To Use the Internal 6 in 1 Card Reader To Use with Windows 98SE Me and 2000 eese nnne nnne nnn 6 To Use with Windows XP eere nen nmn nh renun arena ranae n nnmnnn 7 To Use with Linux Kernel 2 4 or Later cese nmm nnm 8 To Safely Remove Memory Cards To REMOVE in VVINGOWS x eonim iirexluvexexvE Vc Pda vaa YRUN E ORE NAE ERN SR DWE EXXEEVE UV TEER TY RE rA CV DEF QU VE ES 8 To Remove in LINUX cececececcececececeneececenenceceaeneaeeaeaeneaceneneuseceaeaeaneaeaensacsaeaeaseceaeaeaneaeneaeaneneas 8 Boot up Function To Boot up with Pheonix or Award BIOS eeeeeeeeen eee nennen nnn nnn nnns 9 To Boot up with AMI BIOS lseeeeeeee eene enne nennen nnn nn nura nnn
5. ction All Transcend Information Inc Transcend products are warranted and tested to be free from defects in material and workmanship and to conform to the published specifications Should your Transcend Card Reader malfunction during normal use in its recommended environment due to improper workmanship or materials within the warranty period Tran scend will repair or replace your product with a comparable product This warranty is subject to the conditions and limitations set forth herein Duration of Warranty Transcend Card Readers are covered by this warranty for a period of two 2 years from the date of purchase Transcend will inspect the product and make the determination as to whether the product is eligible for repair or replacement The decision by Transcend regarding eligibility of the product for repair or replacement will be final and binding Transcend reserves the right to provide a functionally equivalent refurbished re placement product Limitations This warranty does not apply to products that fail due to accident abuse mishandling improper installation alteration acts of nature improper usage or problems with electrical power Transcend Card Reader must be used with devices that conform to the recommended industry standards Transcend will not be liable for damages resulting from a third party device that causes the Transcend product to fail Transcend shall in no event be liable for any consequential indirect or inc
6. e Internal 6 in 1 Card Reader and make sure the USB port is enabled and working properly NOTE Do not plug your Internal 6 in 1 Card Reader into the USB port at this time 2 Insert the Driver CD into the CD ROM drive Auto Run supported Click the Driver button to install the driver If the Auto Run window does not appear double click CardRead exe in the root directory of the Driver CD ISUMPLEDOE Driver CD Transcend Yaur Supplier Your Partner Your Friend www transcendusa com 3 The Choose Setup Language window appears Choose English or Traditional Chinese from the drop down box then click OK Choose Setup Language Select the language for this installation from the choices below 4 The InstallShield Wizard appears Click Next InstallShield Wizard Welcome to the InstallShield Wizard for USE 2 0 Card Reader The InstallShield Wizard will install USB 2 0 Card Reader on your computer To continue click Nest Cancel 5 Click Finish to complete the driver installation InstallShield Wizard Complete Setup has finished installing USB 2 0 Card Reader an your computer If using Windows 98SE or Me the system will ask you to restart Windows Select the No will restart my computer later radio button and click OK Restarting Windows Setup has finished copying files to your computer Before you can use the program you must restart your computer Choose one of the f
7. elp 4e Back b Search L Folders History As Dr x u3 Er Address lg My Computer Go zu E n a 2 p STORAGE Compact Disc D E Displays the contents of your computer Compact Disc Control Panel Removable Removable F Disk G Disk H See alzo My Documents My Network Places Removable Removable Dial Up Hetworkin Disk l Disk fs 1 0 objectis Mv Computer To Use with Windows XP 1 Power on the computer The Found New Hardware status message appears the first time you power on the computer after installing the Internal 6 in 1 Card Read er Lu d p J Found New Hardware Generic STORAGE DEVICE USE Device Four Removable Disk drives with newly assigned drive letters appear in My Com puter The Internal 6 in 1 Card Reader is ready for use My Computer o ef Fie Edit View Favorites Tools Help E d s Search lg Folders Ei Address 4 My Computer a 2 Files Stored on This Computer System Tasks View system information LJ Shared Documents CJ CHZ s Documents T Add or remove programs G Change a setting Hard Disk Drives Other Places IT ge Local Disk C My Network Places E My Documents Shared Documents Devices with Removable Storage E Control Panel A SEERE e 314 Floppy A A 4 CD Drive D p m Details Sus up tty comaa Removable Disk E Removable Disk F ystem Folder
8. idental damages lost profits lost business investments lost goodwill or interference with business relationships as a result of lost data Transcend is also not responsible for damage or failure of any third party equipment even if Transcend has been advised of the possibility This limitation does not apply to the extent that it is illegal or unenforceable under applicable law Disclaimer The foregoing limited warranty is exclusive with no other warranties implied or statutory including but not limited to any implied warranty of merchantability or fitness for a particular purpose This warranty is not affected in any part by Transcend s providing tech nical support or advice Transcend Transcend Information Inc Your Supplier Your Partner www transcendusa com Your Friend The Transcend logo is a registered trademark of Transcend Information Inc All logos and marks are trademarks of their respective companies
9. letion of the appropriate procedure for your BIOS as described below a CompactFlash card can be used to boot up your computer To Boot up with Pheonix or Award BIOS 1 Power on your system and follow the on screen instructions to enter BIOS or the CMOS setup utility 2 Refer to the owner s manual of your motherboard for details about the configuration program for your system 3 Enter STANDARD CMOS SETUP and select Advanced BIOS Features CMOS Setup Utility Copyright C 1984 ru ee a ee ee b Standard CHOS Features P Advanced BIOS Features Advanced Chipset Features gt Integrated Peripherals gt Power Management Setup p PnP PCI Configurations 4 Select USB ZIP for the First Boot Device then press ESC CMOS Setup Utility Copyright C 1984 2881 Award Sof fiduanced BIOS Features Uirus Harning Disabled CPU L1 amp L2 Cache CEnab led Quick Power On Self Test Enabled First Boot Device USB ZIP1 Second Boot Devic Third Boot Device First Boot Device Boot Other Device Suap Floppy Drive SCS Boot Up Floppy E CDROM Boot Up NunLock S HDD 1 A Gate AZB Option HDD 2 Typenatic Rate Se HDD 3 d Al USB FDD Security Option USB ZIP 5 Choose Save amp Exit Setup to save the new configuration to CMOS and exit the CMOS Setup program At SAVE to CMOS and EXIT Y N Type Y and press Enter 6 Reboot your system To Boot up with AMI BIOS 1 P
10. nn nanus a nna n nanus 10 SDOCHITICallollS otiose mecs En e M EAD ELE E E 12 Card Reader Limited Warranty Introduction Thank you for purchasing Transcend s Internal 6 in 1 Card Reader a small device de signed for fast easy data exchange using six types of storage media CompactFlash IBM Microdrive SmartMedia Secure Digital MultiMediaCard and Memory Stick PRO Designed to fit in any 3 5 drive Transcend s Internal 6 in 1 Card Reader is easy to install in your computer Package Contents The Internal 6 in 1 Card Reader package includes the following items Internal 6 in 1 Card Reader Driver CD Quick Installation Guide Features The Internal 6 in 1 Card Reader has the following features Compliant with USB specification version 2 0 e Supports six kinds of storage media CompactFlash Card Type I II IBM Microdrive SmartMedia Card Secure Digital Card MultiMediaCard Memory Stick PRO e Hi Speed with transfer rate up to 480 Mbps e LEDs indicate card insertion and data traffic e Boot Up function and Easy installation System Requirements E Desktop computer with an onboard USB pin header and 3 5 drive bay One of the following operating systems Windows 98SE Windows 2000 Windows Me Windows XP No driver needed Linux kernel 2 4 or later Driver Installation Driver Installation for Windows 98SE Me and 2000 1 Power on the computer where you will install th
11. ollowing options and click DK to finish setup C Yes want to restart my computer now 6 Turn off the computer and refer to Hardware Setup below to set up the Internal 6 in 1 Card Reader Driver Installation for Windows XP Linux Kernel 2 4 or Later No driver is needed Turn off the computer and refer to Hardware Setup below to install the Internal 6 in 1 Card Reader into your PC Hardware Setup 1 Install the Internal 6 in 1 Card Reader into an available 3 5 drive bay Find the layout of the USB pin header in the owner s manual of your motherboard If the layout of the USB pin header is as shown below it matches the default setting of the USB connector A s Pin 1 USB Power Q 3 Pin 2 USB 0 e Pin 3 USB Pin 4 GND Pin 5 NC USBOC Pin 6 USB Power Pin 7 USB Pin 8 USB Pin 9 GND Pin 10 NC No pin If the layout of the USB pin header is not as shown above skip step 4 and go directly to step 5 4 Plug the USB connecter of the Internal 6 in 1 Card Reader into the USB pin header on the motherboard with the red wire seated in pin 1 or pin 6 Hardware setup is complete xXx lt OO p JET D gH 2O J Oo A Y gy e Plug the USB connecter with the red wire seated in pin 1 or pin 6 Ly ae APA ay 5 Ifthe layout of USB pin header does not
12. ower on your system and follow the on screen instructions to enter BIOS or the CMOS setup utility 2 Refer to the owner s manual of your motherboard for details about the configuration program for your system 3 Enter the CMOS Setup Utility main page select Integrated Peripherals and press Enter AMIBIOS NEW SETUP UT gt Standard CMOS aare gt Advanced BIOS Features gt Advanced Chipset Features gt Power Management Features gt PNP PCI Conf igurations gt Integrated Peripherals 4 Select USB Device Legacy Support and change the setting to All Device ANIBIOS NEW SETUP UTILITY Integrated Peripherals USB Controller Enabled USB Device Legacy Support All Device gt On Chip IDE Configuration OnBoard LAN Enabled AC 97 fudio fiuto gt Set Super 1 0 5 Press Esc to return to CMOS Setup Utility main page Select Advanced BIOS Features and press Enter AMIBIOS NEW SETUP UTILITY VEJ gt Standard CMOS Features gt Advanced Chipset Features gt Power Management Features Load BIOS gt PNP PCI Configurations gt Integrated Peripherals gt PC Health Status 10 6 Select Boot Device Select AMIBIOS NEW SETUP UTILITY Advanced BIOS Features Quick Boot Disabled Full Screen LOGO Show Silent gt Boot Device Select S M A R T for Hard Disks BootUp Num Lock n Floppy Drive Swap Disabled Floppy Drive Seek Disabled Password Check Boot To 03 2 T Select USB RMD
Download Pdf Manuals
Related Search