APC HP Mounting Rails - 1 set
Contents
1. Section 2 Mounting Instructions for J1451A B J1452A B J1491A To install J1451A B J1452A B or J1491A into an APC NetShelter follow the steps in Table 4 Note Your shelf and bezel might vary from the ones shown in the table If the slides are not attached to the shelf skip ahead to Step 4 4 11 Table 4 Installation Procedure for J1451A B J1452A B J1491A Step Action Figure Remove the slides from the server shelf assembly 1 Place the shelf assembly on the floor and extend the slides to their full length J1451 shown 2 Remove the front and middle M4 x 6mm slide screws 3 Move the middle section of the slide forward until the rear screw head is visible through the large hole in the slide Remove the M4 x 6mm screw through the hole Repeat this procedure for the remaining slide Middle a Front Rear screw visible through hole in middle section of slide Side View Determine the mounting location of the bezel 4 Place the bezel J1451 shown against the vertical mounting rails at the location you have chosen for your server s The bottom of the bezel should align with the bottom of a U one mounting hole below a notched mounting hole Using a pencil mark the locations of the two upper bezel mounting holes on the corner posts Mark the location of the lower edge of the bezel on both of the ve2. A Screw Phillips Flat Head 2 10 32 x 1 2 X DD Mounting Block 1 Installation Instructions 1 Tools Required To install the Mounting Rail Kit for HP Shelving AR8001 you will need the following hand tools e Screwdrivers flat blade and Phillips e Nut Drivers 3 8 and 8mm e Torx Screwdriver T 25 e Pencil 2 11 Section 1 Mounting Instructions for J1456A J1496A To install J1456A or J1496A into an APC NetShelter follow the steps in Table 3 below Table 3 Installation Procedure for J1456A and J1496A Step Action Figure 1 Choose the location for the mount ing rails on the vertical rails of the NetShelter Keep in mind the U space required by the servers to be mounted on the shelf and that the shelf will hang one U below the location of the rail The bottom of each rail must align with the bottom of a U as shown Mount the rail s 4 hole end facing the front of the Net Shelter with the long flat side of the rail facing inward 2 Fasten each end of both mounting rails with two M6 x 12mm flat head screws On the front end insert the screws into the middle two holes as shown Note that the bottom screw fits into the notched mounting hole on the vertical rail of the NetShelter Make sure that the mounting rail is level On the rear end of each mounting rail insert the screws into both holes 3 Partially fasten two turns one HP supplied 10 32 x 1 2 To
3. BW 7 8 11 Table 5 Installation Procedure for J1455A Step Action Figure 3 To install the shelf to the slide rail assembly refer to the HP Net Server Rack Mount Kit instruc tions Step 2 Attaching the Base to the Rails Note You will need to use M6 x 18mm screws M6 cup washers and M6 caged nuts in the top and bottom holes of the filler panels and ears in place of HP supplied Timmerman nuts and decorative screws The middle hole is inacces sible Note APC offers a Cable Hoop Kit AR8113 for use with the J1455A shelf It replaces the HP cable management brackets Section 4 Mounting Instructions for LXr Pro To install the HP LXr Pro into an APC NetShelter follow the steps in Table 6 below Table 6 Installation Procedure for LXr Pro Step Action Figure Align the attached mounting studs of the HP slides to the bottom holes in the mounting rails Fasten each HP slide to the mounting rail using the HP supplied M6 locking nuts 9 11 Table 6 Installation Procedure for LXr Pro Step Action Figure If you plan to install the cable management of the LXr Pro attach the mounting block to the rear end of a mounting rail with one 6 32 x 3 8 flat head screw Mount the slide rail assemblies to the vertical mounting rails of the NetShelter using the M6 x 12mm slotted screws Use two screw
4. level Use one screw in the lower hole at the rear Repeat Steps 7 and 8 for the second mounting rail slide assembly x EO _ M6 x 12mm mounting screws of bezel RS ee J1451A B J1491A Pencil mark at bottom edge ae M6 x 12mn mounting screws Pencil botto of bez ea J1452A B n 6 11 Table 4 Installation Procedure for J1451A B J1452A B J1491A Step Action Figure Attach the server shelf to the mounted slides install the cable management arm optional NetServer and bezel optional 9 To attach the server shelf to the mounted slides refer to Steps 2 and 3 in this table 10 If you are installing the cable man agement arm Refer to the instructions supplied with the HP NetServer Rack Mount Kit to mount the cable man agement arm to the shelf To attach the cable management arm to the NetShelter place an M6 caged nut in the fourth mounting hole above the bottom screw that fastens the rail slide assembly to the vertical mounting rail Use two 2 M6 x 18mm screws and two 2 M6 cup washers to mount the cable management arm to the rear vertical rail Install and M6 x 12mm flat head screw into the upper mounting hole at the rear of the rail slide assembly on the side opposite the cable management arm M6 Caged Nut Cup Washer o
5. APC NetShelter Mounting Rail Kit for HP Shelving AR8001 Overview The Mounting Rail Kit for HP Shelving AR8001 allows you to install into an American Power Conver sion APC NetShelter the Hewlett Packard HP NetServer Rack Mount Kits listed in Table 1 below There are four sets of instructions in this document Refer to Table 1 to determine which set of instructions to use for the HP kit you are installing Table 1 HP NetServer Rack Mount Kits use HP If you are using and refer HP NetServer ee haa to Section Mount Kit model ai LM LS LF LH J1451A B 2 LC J1452A B 2 LX Pro LXe J1455A 3 LCI J1456A 1 LHII LH Pro LD Pro J1491A 2 E Series J1496A 1 LXr Pro Kit included with 4 server Inventory Table 2 shows the parts that are included in the Mounting Rail Kit for HP Shelving AR8001 Some of the parts used in the installation are supplied with the HP kits Table 2 Inventory of APC Mounting Rail Kit for HP Shelving AR8001 Item Quantity Figure Mounting Rail 2 o PA Nut Caged M6 3 990 5016A Rev 3 6 00 Table 2 Inventory of APC Mounting Rail Kit for HP Shelving AR8001 Item Quantity Figure Washer Nylon Cup M6 6 A gt Y Screw Phillips Slotted M6 x 6 lt 18mm OD Cy Screw Slotted Flat Head 8 M6 x 12mm MD Screw Slotted Flat Head 1 6 32 x 3 8 Mum Screw Phillips 10 32 x 3 4 2
6. coopocorocoporoorcrretp EEEREN vA OOO OU OU NU ODDO OU TOO Doo Doo Doo ooo Do oe eeu UU TUL OO no Oo San M6 x 12mm Screw Flat head Screw 11 Follow the procedures in the HP NetServer Rack Mount Kit instruc tions to mount the server and bezel optional to the shelf Note You will need to use M6 x 18mm screws M6 cup washers and M6 caged nuts in the top holes of the bezel in place of the HP supplied Timmerman nuts and dec orative screws 7 11 Section 3 Mounting Instructions for J1455A To install J1455A into an APC NetShelter follow the steps in Table 5 below Table 5 Installation Procedure for J1455A Step Action Figure 1 Attach each slide to a mounting rail using four 4 10 32 lock nuts supplied with the HP NetServer Rack Mount Kit Front Determine the mounting location of the slide rail assembly by using the HP supplied ears in the same manner as Table 4 Step 4 Mount the assembly to the Net Shelter with four 4 M6 x 12mm slotted screws Use two screws at the rear of each mounting rail Use two screws in the front of the mounting rail one in the bottom mounting hole and one in the third from bottom mounting hole Uf PT Wf A Y J Y yy J fy If f jf FH 7 7 TOY YY yy A y y f Jj SSES AUB PS BSE ED DP DB BBE BBD BBB DEB BD BE BBB
7. rtical mounting rails Remove the bezel and place it aside Align top of bezel here Bezel mounting hole Bottom edge d of bezel 5 11 Table 4 Installation Procedure for J1451A B J1452A B J1491A Step Action If you plan to install the bezel install M6 caged nuts into the square mounting holes next to each of the upper pencil marks that you made in Step 4 For detailed instructions on installing caged nuts see the NetShelter User Man ual Caged Nuts Attach the slides to the mounting rails 6 Attach one of the slides removed in Step 1 to a mounting rail using two of the M6 nuts supplied with the HP NetServer Rack Mount Kit Make sure that the slides are prop erly oriented with respect to the mounting rail and that they can be extended frontward without inter ference from the bracket Repeat for the second bracket Front Rear Mount the mounting rail slide assembly to the NetShelter 7 Place one of the mounting rail slide assemblies into the NetShelter and align the bottom edge of the front mounting ear with the pencil mark that indicates the bottom edge of the bezel See Step 4 Mount the assembly with three M6 x 12mm flat head screws Use two screws in the front of the mounting rail J1451A B and J1491A bot tom two holes J1452A B bottom and third from bottom holes Make sure that the mounting rail is
8. rx screw to top pre inserted PEM nut at the rear of each rail The grooves on the rear of the shelf assembly will slide along these screws See Step 5 3 11 Table 3 Installation Procedure for J1456A and J1496A Step Action Figure Tilt the shelf slightly as you place it in the rack to avoid hitting the screws that protrude from the sides of the shelf DoooooDooooO ooo ooo oeaSsseoooooooooooooooOd a S Poooooooooood Doo Oooo ooo ooo aae Align the rear slots of the shelf with the 10 32 x 1 2 Torx screws installed in Step 3 Slide the shelf along the screws until the front is flush with the front vertical rails Attach one 10 32 x 1 2 Phillips head screw through each inside mounting hole located near the front of the shelf and tighten Tighten the screws along the back grooves of the shelf 4 __ __ _ P EEEE CEEL CECEEEEE EEEE SEREA mEt Hew ou Esmaea z Follow the procedures in the HP NetServer Rack Mount Kit instruc tions to mount the server s and ears optional to the shelf Note You will need to use M6 x 18mm screws M6 cup washers and M6 caged nuts in the top and bottom holes of the ears in place of HP supplied Timmerman nuts and deco rative screws The middle hole is inaccessible
9. s in the front of the mounting rail one in the bottom mounting hole and one in the third from bottom mounting hole Make sure that the mounting rail is level On the rear end of each mounting rail insert the screws into both holes Note If you used the mounting block in Step 2 use two 2 10 32 x 3 4 Phillips screws at the rear of the bracket with the mounting block Dh bh bh hh hhh b hb bh hn bhnb bby 7 7Qul i Jl Eb hn hhh bn bn bbb bn bh M6 x 12mm mounting screws Attach the shelf to the rail slide assembly Follow the instructions in the HP LXr NetServer Pro Series User Guide Mounting the NetServer in a Rack Installation Procedure Step 2 Attaching the Base to the Rails 10 11 Table 6 Installation Procedure for LXr Pro Step Action Figure 5 To attach the cable management arm to the right rear vertical mounting rail as viewed from the front of the NetShelter remove the lower 10 32 x 3 4 Phillips screw you used in Step 3 Insert the screw through the middle hole of the cable management arm bracket and partially through the bottom hole of the installed slide rail assembly Rotate the cable management arm and remove the top screw supporting the slide rail assembly Re position the cable management arm as shown and insert the screw into the top hole and through the top hole of the slide rail a
10. ssembly Tighten both screws To mount the cable management arm to the other rear vertical mounting rail follow the instruc tions in the previous paragraph Note that the cable management arm bracket will be inverted and the screws will fit into its lower two holes 6 Mount the cable management arm to the LXr Pro server shelf accord ing to the instructions Cable Man agement Arm Kit for the HP NetServer LXr Pro T Install the server onto the shelf and install the front bezel Continue with the instructions supplied with the HP NetServer Rack Mount Kit to mount the cable management arm to the shelf NetShelter is a trademark of American Power Conversion Torx is a registered trademark of Camcor Tex tron Inc All other trademarks are property of their respective owners 11 11
Download Pdf Manuals
Related Search