BDI Avion 8925
Contents
1. Component List il 2e Z dD Designed by BDI Design Studio These distinctive product configurations are protected by US and international patents trade dress and or copyright laws Avion and BDI are trademarks of Becker Designed Inc All Rights reserved 2009 BDI Made in China 89225REV102909v2 AVION 8925 A Phillips Screwdriver x1 B 4mm Hex Driver x2 C Hollow Bolt Wrench x D Hollow Bolts x 4 Pre installed on Metal Legs H E 1 4 20 x 2 Machine Screw x 6 F Assembled Cabinet x1 G Metal Rail x 2 H Metal Leg x 2 l M4 x 25mm Screws x4 J Handle x 2 K Adjustable Shelf x2 M Back Panel x 1 ASSEMBLY INSTRUCTIONS BDIUSA COM TN Your Avion Home Theater Furniture is engineered for easy assembly Carefully follow this procedure to prevent any damage Placement and Maintenance Avion Home Theater Furniture is designed for indoor use on level floors Clean glass with glass cleaner and steel parts and wood veneer with a moist cloth Step 1 Unpack and identify the components at left Note that some components are shipped inside the cabinet The assembly workspace should be a non marring surface such as carpet For missing hardware pieces please contact BDI Customer Service at customerservice bdiusa com For all other concerns please contact your BDI Retailer Step 2 Build and Install2. Base Assembly First remove all internal components from the cabinet including shelves hardware box and legs Carefully lay Assembled Cabinet F back side down Using the Hollow Bolt Wrench C remove the four 4 pre installed Hollow Bolts D from Metal Leg H Screw the Metal Rail G to the top of Metal Leg H with Hollow Bolts D NOTE Make sure that the larger bolt opening on Metal Rail G faces toward the Detail view of Hollow Bolts D connecting the Metal Rail G to the top of Metal Leg H Step 3 Carefully lay Assembled Cabinet F back side down Using one of 4mm Hex Drivers B attach the completed base assembly to the bottom of the Assembled Cabinet F with 1 4 20 x 2 Machine Screws E Note Each of the metal legs has levelers that can be adjusted from inside the cabinet using one of the 4mm Hex Drivers B Completed base assembly Oy Ex6 Step 4 Install Handles J on the doors and drawers using the M4 x 25mm Screws I and the Phillips Screwdriver A supplied Adjustable shelf pins pre installed may be repositioned allowing you to raise or lower the adjustable shelf to the desired level Install Adjustable Shelf K inside the left and right cabinet area Note To place the adjustable shelf inside the cabinet the shelf mus
3. Turning the leveler clockwise will extend the leveler turning it counter clockwise will retract it CORRECT Door is sit ting squarely and evenly spaced on tops and sides INCORRECT Door is out of alignment with the rest of the unit TEP 2 Adj Door Hin if n The doors on your cabinet should be evenly spaced and the doors should open and close freely without rubbing against the door frame If the cabinet s doors appear out of alignment this condition can be corrected with minor adjustment to the European hinges on each door Because these hinges are infinitely adjustable adjusting one hinge element can sometimes cause the need for adjustments to other elements But with a few adjustments you can modify the orientation of the cabinet doors to make sure that they hang perfectly within your cabinet Use a Phillips screwdriver to adjust the door hinges By adjusting Screw 1 the door will move LEFT or RIGHT within the frame Make minor adjustments at both top and bottom hinges for best results By adjusting Screw s 2 the door will move UP or DOWN within the frame the top and bottom hinges must be adjusted the same amount By adjusting Screw 3 the entire door will move IN or OUT opening or closing the gap between the door frame and cabinet this screw rarely needs adjustment BDi AVION ASSEMBLY INSTRUCTIONS 8925 4 BDIUSA COM CUSTOMERSERVICE BDIUSA COM
4. cabinet is engineered to include a range of adjustments Please read and retain this guide so that you can fully enjoy the look and use of your cabinet for years to come Unless manual leveling is required or you wish to prevent the cabinet from rolling you may prefer to keep the cabinet s levelers up and off the floor This allows easier cabinet movement for greater access to rear panels and wire management and permits easier cleaning vacuuming underneath the cabinet By following the steps in this guide you can be sure that your BDI cabinet is in optimum tune and adjustment If you need additional assistance contact BDI at customerservice bdiusa com Fine tuning your BDI Avion Home Theater Furniture After unpacking and assembling your cabinet inspect it to be sure that it is sitting level on the floor that all doors appear level and that they open and close freely without rubbing or binding Due to uneven floors or perhaps gentle jostling during shipment your BDI cabinet may not appear to be in perfect alignment when first assembled or when loaded with heavier electronic equipment Such alignment issues are usually minimized or eliminated with only a few minor adjustments CY a TEP 1 Level th in if n 8 Levelers are integrated into each leg assembly and are accessed from inside the cabinet If your floor is uneven you may extend one or more levelers with the provided 4mm Hex Drivers B to attain a level stable cabinet placement
5. t be tilted sideways to clear the door opening BDi AVION ASSEMBLY INSTRUCTIONS 8925 BDIUSA COM CUSTOMERSERVICE BDIUSA COM Step 5 Install both Back Panels M to the backside of the cabinet Note Velcro straps are included as wire management for your convenience Step 6 Optional fabric speaker or glass insert panel Avion s drawer and door fronts feature removable replaceable panel inserts to permit customization of your cabinet s appearance and utility Contact BDI Customer Service at customerservice bdiusa com Installing optional panel inserts is quick and easy 1 From the inside of the door and starting at one corner of the pre installed Glass or Speaker panel insert carefully pull away all four sections of the panel retention trim running along the perimeter of the insert Use a blunt tapered object or your finger to start removing the rubber material a Remove rubber trim and 2 Once the trim material is completely pulled away remove the glass panel pre installed panel insert and replace it with the desired panel insert 3 Re install the trim pressing it carefully back into the groove around the new panel insert section by section to complete the panel insert installation b Replace insert panel a BDi AVION ASSEMBLY INSTRUCTIONS 8925 3 BDIUSA COM CUSTOMERSERVICE BDIUSA COM Thank you for choosing BDI Your BDI home theater
Download Pdf Manuals
Related Search