Miele DA420-6 V
Contents
1. Data sheet for domestic cooker hoods In acc with delegated regulation EU No 65 2014 and regulation EU No 66 2014 MIELE Model name identifier DA 420 V 6 EXT Annual Energy Consumption AEC ooa 8 8 kWh year Energy efficiency class A most efficient to F least efficient A Energy efficiency index EEl ooa 40 0 Fluid Dynamic Efficiency FDE o4 Fluid Dynamic Efficiency class A most efficient to G least efficient Lighting Efficiency LEyooa 45 8 Ix W Lighting Efficiency class A most efficient to G least efficient A Grease Filtering Efficiency Grease Filtering Efficiency class A most efficient to G least efficient Airflow at best efficiency point m3 h Air flow min speed m3 h Air flow max speed m3 h Air flow intensive or boost setting m3 h Max air flow Qmax m3 h Air pressure at best efficiency point Pa Airborne acoustical A weighted sound power emissions min speed dB Airborne acoustical A weighted sound power emissions max speed 0 dB Airborne acoustical A weighted sound power emissions intensive or dB boost setting Electrical power input at best efficiency point W Power consumption in off mode P W Power consumption in standby mode P 0 15 W Nominal power of lighting system 12 0 W Average illumination of the lighting system on the cooking surface 550 Ix Time increase fact2. Select a pan which is suitable for the size of the burner Regulate the flame so that it does not burn up the sides of the pan Avoid overheating the pan e g when cooking with a wok gt Always switch the cooker hood on when a cooking zone is in use otherwise condensation may collect in the hood which could cause corrosion When cooking with oil or fat chip pans and deep fat fryers etc do not leave the pans unattended Never leave an open grill unattended when grilling Overheated oil and fat can ignite and could set the cooker hood on fire 10 Warning and Safety instructions gt Do not use the cooker hood without the filters in place This way you will avoid the risk of grease and dirt getting into the appliance and hindering its smooth operation gt There is a risk of fire if the cooker hood is not cleaned as described in these operating instructions gt The cooker hood can get very hot during cooking due to heat rising from the hob Do not touch the housing or the grease filters until the cooker hood has cooled down Correct installation gt Refer to the cooker or hob manufacturer s instructions as to whether a cooker hood may be operated above the cooker hob gt Safety regulations prohibit the fitting of a cooker hood over solid fuel stoves Insufficient distance between the cooker or hob and the cooker hood can result in damage to the hood The minimum safety distances between
3. EU No 65 2014 and regulation EU No 66 2014 MIELE Model name identifier DA 420 V 6 Annual Energy Consumption AEC ooa 36 4 kWh year Energy efficiency class A most efficient to F least efficient A Energy efficiency index EEl ooa 45 7 Fluid Dynamic Efficiency FDE o4 35 5 Fluid Dynamic Efficiency class A most efficient to G least efficient A Lighting Efficiency LEyooa 45 8 Ix W Lighting Efficiency class A most efficient to G least efficient A Grease Filtering Efficiency 95 1 Grease Filtering Efficiency class A most efficient to G least efficient A Airflow at best efficiency point 318 9 m3 h Air flow min speed 220 m3 h Air flow max speed 460 m3 h Air flow intensive or boost setting 700 m h Max air flow Qua 700 m h Air pressure at best efficiency point 421 Pa Airborne acoustical A weighted sound power emissions min speed 48 dB Airborne acoustical A weighted sound power emissions max speed 62 dB Airborne acoustical A weighted sound power emissions intensive or 72 dB boost setting Electrical power input at best efficiency point 105 0 W Power consumption in off mode P W Power consumption in standby mode P 0 15 W Nominal power of lighting system 12 0 W Average illumination of the lighting system on the cooking surface 550 Ix Time increase factor 0 7 55 Technical data
4. affect the functioning of the filters in any way After cleaning m After cleaning leave the filters to dry on an absorbent surface before replacing them m When removing the filters for cleaning also clean off any residues of oil or fat from the now accessible housing to prevent the risk of these catching fire m Replace the grease filters making sure that the locking clips are facing down towards the hob dai1619 29 Cleaning and care m If a grease filter is inadvertently replaced upside down insert a small screwdriver blade into the slit to disengage the clip Resetting the grease filter operating hours counter After cleaning the operating hours counter needs to be re set m Whilst the fan is switched on press the operating hours control for approx 3 seconds until only the 1 is flashing The grease filter symbol goes out If you want to clean the grease filter s before the operating hours counter has reached its maximum m Press the operating hours control amp for approx 6 seconds until only the 1 is flashing 30 Charcoal filter If the cooker hood is connected for recirculation a charcoal filter must be inserted in addition to the grease filters This is designed to absorb cooking odours and is fitted in the canopy above the grease filters Replacement charcoal filters can be obtained from your Miele retailer or via the internet at www miele sho
5. agent for stainless steel available from Miele can also be used Follow the manufacturer s instructions on the packaging Important for RAL coloured housing Special order finish m Please observe the general notes on cleaning earlier in this section It is very difficult to clean this type of surface without causing minor marks to the surface material This can become particularly noticeable depending on the type of lighting in the kitchen 27 Cleaning and care Important for the controls Do not leave soiling on the controls for any length of time Otherwise they may suffer discolouration or damage Remove soiling straight away m Please observe the general notes on cleaning earlier in this section Do not use stainless steel cleaning agents on the controls 28 Grease filters The re usable metal grease filters in the appliance remove solid particles grease dust etc from the kitchen vapours preventing soiling of the cooker hood A An oversaturated filter is a fire hazard Cleaning interval The grease filters should be cleaned regularly at least every 3 4 weeks to avoid a build up of grease Clean them immediately if the Grease filter operating hours symbol lights up m You can set the operating hours counter for the grease filters to suit the type of cooking you do see Operation Removing a grease filter The grease filter can fall out when you are handlin
6. approx 10 seconds until the indicator for power level 1 lights up m Then press in turn the button then the button then the lighting button The cooker hood is now in signing on off mode If a wireless connection has not yet been established 2 and 3 will flash at the same time If a wireless connection has already been established 2 and 3 will light up constantly Con ctivity 2 0 is already activated or a remote control is signed on m To activate Con ctivity 2 0 press the button The search for a signal will start m Meanwhile start activating the hob Activating Con ctivity 2 0 Activating the hob m While the cooker hood is searching for a signal start activating the hob More information about this can be found in the Operating instructions for the hob m When the hob registers that connection has been established confirm activation on the cooker hood with the run on option control 5415 All indicators will go out m Confirm activation on the hob Con ctivity 2 0 is now ready to use If you do not confirm within 4 minutes activation will not take place Activation failed m f connection cannot be established despite activating the Con ctivity function on the cooker hood and hob the function must be deactivated on both appliances and then the procedure repeated Deactivating Con ctivity 2 0 m Deactivation on the cooker hood is carried out in the same way
7. hob and the cooker hood see Activating Con ctivity 2 0 The hob transmits information about its operational status via a wireless signal to the cooker hood When the hob is switched on the hob lighting comes on independently and then after a short time the fan also comes on During cooking the cooker hood automatically sets the power level according to the number of cooking zones in operation and their power levels After switching the hob off the fan and the hob lighting will switch off automatically after a specified period of time See Operation for detailed information about this function 15 Guide to the appliance Guide to the appliance Telescopic extension piece 2 Tower 3 Height adjustable canopy Controls Grease filters Spacer frame The spacer frame creates a shadow gap between the tower and the ceiling The cooker hood can be installed with or without the spacer frame Recirculation grilles only for recirculation mode DA 420V 6 only Hob lighting Charcoal filter Special accessory for recirculation mode DA 420V 6 only Control for the hob lighting 4 On Off control for the fan 2 Controls to select the fan power level 43 Control for the run on option Operating hours control 9 Controls for raising and lowering the canopy 17 Operation Automatic mode When Con ctivity 2 0 is activated the cooker hood always wor
8. 50480 Kuala Lumpur Malaysia Phone 603 6209 0288 Fax 603 6205 3768 New Zealand Miele New Zealand Limited RD 98 463 631 Level 2 10 College Hill Freemans Bay Auckland 1011 NZ Tel 0800 464 353 nternet www miele co nz Singapore iele Pte Ltd 163 Penang Road 04 03 Winsland House II Singapore 238463 Tel 65 6735 1191 Fax 65 6735 1161 E Mail info miele com sg nternet www miele sg South Africa Miele Pty Ltd 63 Peter Place Bryanston 2194 P O Box 69434 Bryanston 2021 Tel 011 875 9000 Fax 011 875 9035 E mail info miele co za nternet www miele co za United Arab Emirates iele Appliances Ltd P O Box 11 47 82 Gold amp Diamond Park Sheikh Zayed Road Building 6 Offices Nos 6 214 to 6 220 Dubai Tel 971 4 341 84 44 Fax 971 4 341 88 52 E Mail info miele ae nternet www miele ae DA 420V 6 DA 420V 6 EXT DA 424V 6 DA 424V 6 EXT C en GB M Nr 09 813 720 06
9. O T 50 hours m Press the symbol for a shorter operating time or the symbol to select a longer operating time m Confirm the selection by pressing the operating hours control All the indicators will go out If you do not confirm within 4 minutes the cooker hood will revert to the old setting 23 Operation Automatic and Manual modes Activating and altering the charcoal filter operating hours counter The charcoal filter is needed for recirculation mode The operating hours counter for the charcoal filter needs to be activated once and the operating hours counter needs to be set to suit the kind of cooking you do m Use the On Off control to switch the fan off m Press the symbol and the operating hours control at the same time The charcoal filter symbol and one of the fan power levels will flash Fan power level indicators 1 to IS show the time set 1 IERREEEEBE LEE FE UUESEEEEELEEEEEREEUGEUEPEEEEE 120 hours P ABER T 180 hours X T ERROR 240 hours BS nnneen een Deactivated m Press the symbol for a shorter operating time or the symbol to select a longer operating time m Confirm the selection by pressing the operating hours control All the indicator lamps will go out If you do not confirm within 4 minutes the cooker hood will revert to the old setting 24 Reading the filter operating hours counter To check the percentage of time set alre
10. _ Miele Operating and installation instructions Cooker hood To prevent the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time en GB M Nr 09 813 720 Contents Warning and Safety instructions 44444444400H0nnnnnnannnnnnnnnnnnnannnnnnnnnn nn 4 Caring for the environment 4 44444404snnnnnnnnnnnnnnnnnnnnnnnnnannnnnnnnnnnnnnn 13 Modes 0f operatio Meres a ee hier 14 Gon kctivity 2 0 function een ann aa 15 Guide to the appliance 444444444440Hannnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nn 16 Operation Automatic mode 4444044444nnnH0nnnnnnnnennnnnnnnnnnnnnnnn anne 18 Cooking with Con ctivity 2 0 Automatic Mode 42440444nnnn ernennen 18 Leaving automatic mode temporarily uursersnsnessennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nn 20 Returning to automatic mode 22 ummm44444RRnnnnnannnnnnnnnannnnnnnnannnnnnnnnannnn nn 20 Operation Manual mode u44444400nnnnnnnnnennnnnnnnennnnnnnnnnnnnenn nennen 21 Cooking without Con ctivity 2 0 Manual mode 2240n44nnnnnennnnnnnn ernennen 21 Switching the fan ON ee ea 21 Selecting the power level u umrm44nnannnnnnnannnnnnnnnannnnnnnnnnnnnnnnnnnnnennnnnnannnnn nn 21 Selecting the run on time ussurrrnnnnnnnnnnnnnann
11. ady used m Use the On Off control to switch the fan on m Press and hold the operating hours control B Once to read the Grease filter operating hours The grease filter symbol lights up Twice to read the Charcoal filter operating hours The Charcoal filter symbol lights up One or more of the power level indicators will flash The number of fan power level indicators flashing shows the percentage of the operating time which has already been used up T ni i 25 Tand 2 usn 50 TIOS senken 75 TIO IS ainn i errs 100 The number of operating hours used remains in the memory even when the appliance is switched off or there is a power cut Operation Automatic and Manual modes Adjusting the height of the canopy The height adjustment feature on the canopy can be used to adapt the height of the hood to suit the installation conditions adjust the working area underneath the hood to the height of the user maximise vapour extraction by lowering the canopy during particularly intensive cooking create more working space above the hob by raising the canopy when required m The canopy can be raised or lowered by pressing the VA controls briefly m Pressing one of the controls again stops the canopy If it is not stopped the canopy will automatically be raised or lowered to its fullest extent Repeated use of the height adjustment feature over sev
12. as activation by selecting instead of m To deactivate the hob please refer to the Operating instructions supplied with it You only need to carry out the activation procedure once If the appliances are disconnected from the electricity supply during a power cut for example they will still remain activated Please bear in mind that disabling the signal will also disable any remote control function and this will have to be activated again 53 Technical data Fan motor 130 W Variable height motor 175 W Hob lighting 4x3W Total connected load 317 W Voltage frequency AC 230 V 50 Hz Fuse rating 5A Weight DA 420V 6 37 kg DA 424V 6 45 kg DA 420V 6 EXT 34 kg DA 424V 6 EXT 42 kg For EXT models the connected load and extraction power will depend on the type of external motor fitted Length of connection cable to external motor 1 9 m Recirculation mode with conversion kit DUI 32 and charcoal filter DKF 12 optional accessories Conformity declaration Miele hereby declares that the cooker hoods listed at the end of this booklet comply with the basic requirements and other relevant regulations of Guideline 1999 5 EC A copy of the full Declaration of Conformity can be obtained from the address at the end of this booklet 54 Technical data Data sheet for domestic cooker hoods In acc with delegated regulation
13. be blown directly outside If the on site ventilation system does not have a non return flap the non return flap supplied must be fitted in the exhaust socket in the motor unit 14 Recirculation mode DA 420V 6 only with conversion kit and charcoal filter available as optional accessories see Technical Data dai0494b RR The air is drawn in and cleaned first by the grease filters and then by a charcoal filter The cleaned air is then recirculated back into the kitchen Operation with an external motor EXT model cooker hoods dai0494c RN A Miele extraction fan is installed in a location of your choice outside the room for cooker hoods which are designed to be connected to an external motor The external motor is connected to the cooker hood by means of a control cable and is operated by Con ctivity 2 0 or by the controls on the cooker hood Modes of operation Con ctivity 2 0 function Automatic control The cooker hood has a communication facility which enables the automatic operation of the cooker hood depending on the operational state of the hob dai3128 To make use of the communication facility the hob must be fitted with a Con ctivity 2 0 Stick Refer to the installation instructions for the Con ctivity 2 0 Stick to check whether it is compatible with your hob To use the Con ctivity 2 0 function a wireless connection must be established between the
14. ce inside upwards to remove 39 Installation UL D M4 x8 5 q dai3173d m Fix the top part to the side of the installation frame for now dai3173c 16x 6 m T20 m Loosen the fixing screws and remove the top part of the installation frame 40 Installation dai3173g dai3173e m Loosen the screws from the exhaust m Place the directional unit in the socket and the hose inside and installation frame with the arrows remove the exhaust socket It is not pointing to the sides required for recirculation mode dai3173f EEN er a m Remove the non return flap It is not required for recirculation mode m Rotate the directional unit by 90 so that the arrows now point forwards and backwards dai3173h 41 Installation dai3173i m Secure the hose to the directional unit socket using a hose clip m Check that the hose is held securely 16x 6 T20 dai3173j m Replace and secure the top part of the installation frame 42 Installation Ny gM INAI x m N Del D m Replace the telescopic piece with the recirculation grilles at the top im 5 dai3152 u The spacer frame can be installed between the tower and the ceiling This creates a shadow which gives the illusion of a gap betwee
15. e lighting remains switched on The cooker hood can now be operated manually see Cooking without Con ctivity 2 0 20 Returning to automatic mode The cooker hood returns to automatic mode m if the cooker hood has not been used for approx 5 minutes after selecting a power level manually or m if the manually selected fan power level corresponds to the automatic one again or m if the cooker hood fan and the hob have been switched off for at least 30 seconds Automatic mode will resume next time the hob is switched on m If you wish to operate the cooker hood manually for a complete cooking process switch on the cooker hood fan before switching on the hob If the cooker hood and the hob have been switched off for at least 30 seconds after cooking automatic mode will resume the next time the hob is switched on Operation Manual mode Cooking without Con ctivity 2 0 Manual mode The cooker hood can be operated manually if Con ctivity 2 0 is not activated You have temporarily deactivated Con ctivity 2 0 see Leaving automatic mode temporarily Switching the fan on m Press the On Off control The fan will switch on at level 2 The symbol and 2 will light up in the power level display Selecting the power level For light to heavy cooking vapours and odours select from power levels 1 to 3 When frying or cooking food with a very strong aroma select the Intensive set
16. e disconnected from the mains electricity supply Warning and Safety instructions Using at the same time as other heating appliances that depend on the air from the room dai1474b A Warning danger of toxic fumes Great care should be taken when using the cooker hood at the same time and in the same room or area of the house as another heating appliance which depends on the air in the room Such appliances include gas oil wood or coal fired boilers and heaters continuous flow or other water heaters gas hobs cookers or ovens which draw air in from the room and duct exhaust gases out through a chimney or extraction ducting When used in extraction mode with or without an external motor fitted or in recirculation mode with a recirculation box installed outside the room the appliance draws air in from the room in which it is installed and from neighbouring rooms If there is insufficient air an underpressure will occur The heating appliance will be starved of oxygen impairing combustion Harmful gases could be drawn out of the chimney or extraction ducting back into the room with potentially fatal consequences Warning and Safety instructions In order to ensure safe operation and to prevent gases given off by the heating appliances from being drawn back into the room when the cooker hood and the heater are in operation simultaneously an underpressure in the ro
17. er hood exhaust socket Secure the exhaust ducting to the exhaust socket e g with a hose clip available as an optional accessory on flexible ducting Place the mains cable and for EXT models the connection cable to the external motor in the ceiling and guide them through the ceiling in the area shown A mains cable of approx 300 mm in length is required between the ceiling and the cooker hood connectors 37 Installation dai3435c m Use a knife to release the four spacers and the two covers from the spacer frame supplied dai3435e m Drill four holes 10 mm approx 115 mm deep for the plugs supplied dai3435d m Place the four plugs in the holes and screw in the 4 screws so that they protrude by approx 30 mm m Use the space frame as a drilling template Place it on the ceiling with the arrows pointing forwards Using the notches align the spacer frame on the intersecting lines and make pencil marks for the drill holes 38 Installation 2x DM4 x8 5 dai3173a m Loosen the two telescopic piece clamps from the installation frame The cooker hood is supplied ready for extraction mode For recirculation mode UL the directional unit from conversion kit DUI 32 optional accessory DA 420V 6 only is installed and the telescopic piece turned upside down UL dai3173b m Pull the telescopic pie
18. eral minutes will cause it to cut out It can be used again after a pause 25 Energy saving tips This cooker hood operates very Make sure that you switch the efficiently and economically The cooker hood off after use following will help you to save even If cooking vapours and odours still more energy when using it need to be removed from the 26 kitchen air after cooking use the run on function The fan will switch off automatically after the selected run on time Ensure that there is sufficient ventilation in the kitchen when cooking In extraction mode if there is insufficient air flow the cooker hood cannot operate efficiently and Clean or change the filters at regular this causes increased operating intervals Heavily soiled filters reduce noise levels performance increase the risk of fire and are unhygienic Always cook with the lowest possible setting This produces fewer cooking vapours SO you can use a lower cooker hood power level and therefore benefit from reduced energy consumption Use the Con ctivity function The cooker hood will switch on and off automatically at the optimum power level for the cooking you are doing which ensures low energy consumption If you are operating the cooker hood manually please note the following Check the power level selected on the cooker hood A lower power level is generally sufficient for the majority of cooking Only use the intensive se
19. ess it again and hold it for approx 6 seconds until only the 1 is flashing Disposing of the charcoal filter m Used charcoal filters can be disposed of with the normal household waste 31 After Sales Guarantee Inthe event of a fault which you cannot remedy yourself please contact your Miele dealer or the Miele Service Department Contact details for Miele are given at the back of this manual N B A call out charge will be applied to service visits where the problem could have been resolved as described in these instructions When contacting your dealer or Miele please quote the model and serial number of your appliance These are shown on the data plate Position of the data plate The data plate is visible after removing the grease filters Guarantee U K In the U K the appliance is guaranteed for 2 years from the date of purchase However you must activate your cover by calling 0330 160 6640 or registering online at www miele co uk Guarantee Other countries For information on the appliance guarantee specific to your country please contact Miele See end of this booklet for contact details 32 Installation Before installation A Before installation it is important to read the information given on the following pages as well as the Warning and Safety instructions at the beginning of this booklet Assembly parts CA mm 4 screws 7 x 110 mm and 4 plugs 10 x 80
20. fumes building up It is essential that the Warning and Safety instructions are observed The cooker hood should be installed according to local and national building regulations Seek approval from the building inspector where necessary m Use smooth or flexible ducting made from approved non flammable materials for exhaust ducting m When using an external motor make sure that the exhaust ducting is sufficiently rigid The external motor can cause an underpressure which can result in the exhaust ducting distorting m To achieve the most efficient air extraction with the lowest noise levels please note the following To ensure efficient air extraction the diameter of the exhaust ducting should not be less than 150 mm If flat ducting is being used the cross section must not be smaller than the cross sectional area of the exhaust socket The exhaust ducting should be as short and straight as possible Only use wide radius bends The exhaust ducting must not be kinked or compressed Ensure that all connections are strong and airtight Remember that any constriction of the air flow will reduce extraction performance and increase operating noise m If the exhaust is ducted through an outside wall a telescopic wall vent or a roof vent available as an optional accessory is recommended dai2538 m f the exhaust air is to be ducted into a flue the ducting m
21. g it This can result in damage to the filter and the hob below Make sure you hold the filter securely at all times when handling it Cleaning and care SI SS SS N SS SI y WNN DI SI S N ONN SR N SER SE SI SS SSS S S N SS IN IN N dai2051 m To take out a grease filter release the locking clip on the filter lower the filter approx 45 unhook it at the back and remove it Cleaning the grease filters by hand m Clean the filters with a soft nylon brush in a mild solution of hot water and a small amount of washing up liquid Do not use neat washing up liquid Unsuitable cleaning agents Unsuitable cleaning agents can cause damage to the surface of the filters if used regularly Do not use cleaning agents containing descaling agents powder cleaners cream cleaners aggressive multi purpose cleaning agents or spray cleaners for grease oven sprays Cleaning the grease filters in the dishwasher m Place the filters as upright as possible in the lower basket with the short sides upright ensuring the spray arm is not obstructed m Use a proprietary household dishwasher detergent m Select a dishwasher programme with a wash temperature between 50 C and 65 C Depending on the cleaning agent used cleaning the filters in a dishwasher can cause permanent discolouration to the surface However this will not
22. h off all cooking zones cooking zone at the highest power level to heat a pan for frying and reduce the power level after approx 60 to 90 seconds a cooking process The cooker hood fan will reduce its power level over the next few minutes and will eventually switch itself off is recognised 60 seconds to 5 This helps to neutralise any lingering minutes for a HiLight hob vapours and odours in the air The cooker hood switches itself onand From the intensive setting 4 the fan when the hob power level has been switches immediately to level 3 reduced the hood switches to power level 3 and remains at that level for approx 5 minutes If the fan is operating at level 3 it will switch to level 2 after approx 1 minute After that the cooker hood power level is determined automatically by the Con ctivity function From level 2 the fan switches to level 1 after 2 minutes After 2 minutes at level 1 the fan m You can select another power level switches itself off manually before then After another 30 seconds the lighting switches off The cooking process is then finished 19 Operation Automatic mode Leaving automatic mode temporarily To leave automatic mode temporarily during cooking m Manually select a different power level or m Manually switch the cooker hood off or m Activate the run on option X on the cooker hood The fan will switch off after the selected time and th
23. ination of the lighting system on the cooking surface 400 Ix Time increase factor 0 7 57 Technical data Data sheet for domestic cooker hoods In acc with delegated regulation EU No 65 2014 and regulation EU No 66 2014 MIELE Model name identifier DA 424 V 6 EXT Annual Energy Consumption AEC ooa 8 8 kWh year Energy efficiency class A most efficient to F least efficient A Energy efficiency index EEl ooa 40 0 Fluid Dynamic Efficiency FDE o4 Fluid Dynamic Efficiency class A most efficient to G least efficient Lighting Efficiency LEyooa 33 3 Ix W Lighting Efficiency class A most efficient to G least efficient A Grease Filtering Efficiency Grease Filtering Efficiency class A most efficient to G least efficient Airflow at best efficiency point m3 h Air flow min speed m3 h Air flow max speed m3 h Air flow intensive or boost setting m3 h Max air flow Qmax m3 h Air pressure at best efficiency point Pa Airborne acoustical A weighted sound power emissions min speed dB Airborne acoustical A weighted sound power emissions max speed 0 dB Airborne acoustical A weighted sound power emissions intensive or dB boost setting Electrical power input at best efficiency point W Power consumption in off mode P W Power consumption in standby mode P 0 15 W Nominal power of lighting
24. king material The packaging is designed to protect the appliance from damage during transportation The packaging materials used are selected from materials which are environmentally friendly for disposal and should be recycled Recycling the packaging reduces the use of raw materials in the manufacturing process and also reduces the amount of waste in landfill sites Disposal of your old appliance Electrical and electronic appliances often contain valuable materials They also contain materials which if handled or disposed of incorrectly could be potentially hazardous to human health and to the environment They are however essential for the correct functioning of your appliance Please do not therefore dispose of it with your household waste Please dispose of it at your local community waste collection recycling centre or contact your Dealer for advice Ensure that it presents no danger to children while being stored for disposal 13 Modes of operation Depending on the model of the cooker hood the following options are available Extraction mode dai0494a RR The air is drawn in and cleaned by the grease filters and directed outside Non return flap The non return flap is designed to prevent the exchange of room and outside air taking place The flap is closed when the cooker hood is switched off When the cooker hood is switched on the non return flap opens for the cooking vapours to
25. ks in automatic Reaction time The cooker hood reacts with a slight mode see Activating Con ctivity 2 0 To operate the cooker hood manually see Cooking without Con ctivity 2 0 Cooking with Con ctivity 2 0 Automatic mode m Switch a cooking zone on at the power level you want delay because altering the power level on the hob does not immediately result in a reduction or increase in cooking vapours Because the hob transmits the information to the cooker hood at intervals this can also cause delays The reaction can vary from a few seconds to a couple of minutes The cooker hood lighting will come on After a few seconds the fan will come on first at power level 2 then it will switch immediately to power level 1 The cooker hood selects the power level automatically during cooking This is determined by the total output of the hob i e the number of cooking zones in operation and the power levels selected m If you select a higher power level or are using several cooking zones the cooker hood will switch to a higher power level m When you reduce the power level or the number of cooking zones on the hob the cooker hood power level is also reduced 000 Gima m X E ee Eae Examples for power levels 1 to 4 Q 0 dai2384j g D 18 Operation Automatic mode Cooking process Switching off m If for example you switch on a m Switc
26. level required and then release it Power management The cooker hood features a power management system to help save energy The fan power level is reduced and the lighting is switched off automatically If the Intensive setting is selected the fan automatically switches to level 3 after 5 minutes From levels 3 2 or 1 the power will be reduced by one level after 2 hours and then in 30 minutes stages until the fan finally switches off The hob lighting will switch off automatically after 12 hours 22 Switching Power management on off You can deactivate Power management This can result in increased electricity consumption m Switch off the fan and the lighting m Press the run on option button 5 amp 15 for approx 10 seconds until 1 lights up in the power level display Then press in turn the lighting button the button and then the lighting button O again If Power management is switched on the 1 and IS indicators will light up constantly If it is switched off 1 and IS will flash m Press to switch Power management off The 1 and IS indicators will flash m To switch it on press The 1 and IS indicators will light up constantly m Confirm the setting with the run on option button 5 415 All the indicator lamps will go out If you do not confirm within 4 minutes the cooker hood will revert to the old setting Operation Automatic and Manual
27. mm for securing the cooker hood to the ceiling The plugs meet European technical requirements for use in concrete ceilings They must only be used together with 7 x 110 mm screws For other types of ceiling construction alternative fixings will be required Make sure the ceiling is able to take the weight of the cooker hood 08162250 08162240 4 extension piece holders 08571140 for aligning and securing the telescopic extension piece 4 screws M4 x 8 5 mm for securing the extension piece holders Om 4 screws M4 x 8 mm for securing the spacer frame to the installation frame DUI 32 conversion kit for recirculation mode not supplied available as an optional accessory The kit includes a directional unit aluminium hose and hose clips 06462181 08095672 dai3149 Other installation accessories may be supplied with the cooker hood which are not required for this model 33 Installation Appliance dimensions N Nah 2 X 220x2201 dai3309a PARAON DA 424V 6 Installation area cut out for feeding through the exhaust ducting the mains cable and with EXT models the connection cable to the external motor In recirculation mode only the mains cable is required 2 Alternative installation with spacer frame 3 Ventilation grille positioned at the top for recirculation A mains connection cable is required to connect the c
28. modes Operating hours counters The number of hours the appliance has been in operation is stored in memory When the Grease filter symbol or the Charcoal filter symbol lights up the operating hours counters are signalling that the filters need to be cleaned or changed Further information about cleaning and changing the filters and resetting the operating hours counter can be found under Cleaning and care Altering the operating hours counter for the grease filters You can set the operating hours counter for the grease filters to suit the type of cooking you do The grease filter operating hours counter is set at the factory for 30 hours Select a shorter time of 20 hours if you roast or fry a lot If you only cook occasionally we recommend that you still select a short time because grease which has built up gradually over a long period of time will harden on the filters and make cleaning more difficult Select a longer time of 40 or 50 hours if you use very little fat for cooking m Use the On Off control to switch the fan off m Press the run on control 54415 and the operating hours control amp at the same time The grease filter symbol and one of the fan power level indicators flash Fan power level indicators 1 to IS show the time set 1 BEEPERENS REDE NEL URELEEETEFEEDNEESCUBETLET 20 hours 2 EAE EE P SPEER 30 hours lt E SEE PENEEEISEOEREEEERE 40 hours TEE EE E
29. n for advice Important This appliance is supplied for connection to an a c 230 V single phase 50 Hz supply The wires in the mains lead are coloured in accordance with the following code Green yellow sseni earth BUG sec 222 22 neutral BroWNi 000R ie live WARNING THIS APPLIANCE MUST BE EARTHED If a flexible connection cable is being used to connect the appliance to the electricity supply the cross sectional area of the the individual leads must be between 0 75 mm and 1 5 mm 51 Activating Con ctivity 2 0 Installing the Con ctivity 2 0 Stick In order to use the Con ctivity 2 0 function the hob must first be fitted with the Con ctivity 2 0 Stick m Please read the separate installation instructions supplied with the Con ctivity 2 0 Stick Activating Con ctivity 2 0 Wireless connection must be activated between the hob and the cooker hood before the Con ctivity 2 0 function can be used Both appliances must be installed and operational Wireless connection must be activated on the cooker hood and the hob at the same time Activation on the cooker hood is described below Activation on the hob is described in the relevant Operating and installation instructions Please refer to the Operating instructions before starting Activate the cooker hood first then the hob 52 Activating the cooker hood m The hob and cooker hood must be switched off m Press the run on option button 54415 for
30. n the ceiling and the tower This is useful if the ceiling is not level or is uneven The cooker hood is aligned vertically with the spacers supplied Visual irregularities between the tower and the ceiling are then concealed by the shadow _ PS dai3435f 4x SS m If you wish to install the cooker hood with the spacer frame remove the four inserts from the fixing holes Installation 4x QmT20 M4x8 dai3173n dai3173m N N EN n I aN i m Mount the spacer frame onto the m Hang the cooker hood on the four installation frame screws making sure the controls are at the front m If using the spacer frame place the two covers into the fixing holes 44 Installation dai3173p m Place the exhaust ducting onto the exhaust socket m For EXT models only Connect the cooker hood and the external motor using the connection cable dai31730 dai3173q m Align the installation frame and secure it with the screws The spacers which were removed from the spacer frame at the start can be used to align the cooker hood vertically dai3173r 45 Installation m Remove the grease filters from the cooker hood 1xO IDT20 M4x16 dai3173s m Remove
31. nnnnnnnnnnnnnnnnannnnnnnnnan nenn nnnannnnn nn 21 SWITCHING TNS fan OFF sinesmena nennen denen here 21 Dimming switching the hob lighting on off 220urs2nsunnnnnnnnnnnnnnnnnnnnnnnnnnn nenn 22 POWer Managem GMt sii sdecesecsasdiceces gd Adetevcdcdeves ieee nn eset 22 Operation Automatic and Manual modes cccsseseeeeeeeesneeeeeeeseneeeeesees 23 Operating NOUS COUNLCIS u nee 23 Altering the operating hours counter for the grease filters u 2224uu gt 23 Activating and altering the charcoal filter operating hours counter 24 Reading the filter operating hours counter uuuurssnnnennssnnnnennnnnnnnn nenn ran nnnnn nn 24 Adjusting the height of the CANOPY u2222uu0nnnnnnannnnnnnnnnnnnnnnnnannnnnnnnnannnn nn anne 25 Energy SAVING tIPS uun 4 ee en anne 26 Cleaning ANG Kor EAWERREPENSBEREPEDGSSEEREEREISESEELPERRSERFPERENKOREEREPENSEHEEEPENFREFTEERENREERBERFERSERPELEER 27 KGASING IRERPERFPBETFPESEPFPEESFEELERTENTNFERBERTTREREPFTEESERLLFENEERE EEBREEESPLEUEFTEEESEE TE ERSTE SEIELFITTERTEEN 27 Grease filters 04000 40nRSer sinne bannen nee a kenne kn are deine 28 Charcoal TUe oeseri ea a a an 30 Resetting the charcoal filter operating hours counter uusnerssnneennnrnnnnnnnnn nenne 31 Disposing of the Charcoal filter uusr 44444H4HHHRnHnnnnnn nenn nnnnnnnnnnnnnn ern nnnn nn 31 After Sales Guarantee ciassa ai eniai asean aii iia ies 32 Po
32. od Account should also be taken of the height of the person who will be using the hood most often They should have sufficient space to work comfortably at the hob and be able to reach the hood controls with ease Please be aware that if positioned too high extraction will be inefficient To achieve optimum vapour extraction the cooker hood must cover the hob It should be positioned centrally over the hob not to the side or to the back of it The hob should be no wider than the cooker hood and if possible it should be narrower The installation area must be easily accessible The cooker hood should be easily accessible and easy to dismantle in the event that service is required This should be taken into consideration when planning the position of cupboards shelves ceilings or features in the vicinity of the cooker hood 36 Protective foil The housing components have protective foil around them to protect them from transport damage m Please remove this foil before fitting the housing components It can be peeled off easily Installation dai3435a dai3435b m With air extraction mode m Draw two intersecting lines on the ceiling Place a section of the exhaust ducting in the ceiling and feed it down through the cross sectional area as illustrated Exhaust ducting of approx 200 mm length is required between the ceiling and the cook
33. om of 0 04 mbar 4 pa is the maximum permissible Ventilation can be maintained by air inlets which cannot be blocked in windows doors or outside wall vents or by other technical measures such as ensuring that the cooker hood can only be switched on when the heating appliance is switched off or vice versa A ventilation brick alone is not generally sufficient to ensure safe ventilation The overall ventilation condition of the dwelling must be taken into account If in any doubt the advice of a competent builder or for gas a qualified gas fitter registered with an official gas safety body in accordance with national safety regulations GasSafe in the UK must be sought If the cooker hood is used in recirculation mode where the air is directed back into the room in which it is located operating a heating appliance which depends on the room air at the same time is no cause for concern Warning and Safety instructions Correct use Never use a naked flame beneath the cooker hood To avoid the danger of fire do not flambe or grill over a naked flame When switched on the cooker hood could draw flames into the filter Fat deposits could ignite presenting a fire hazard The cooker hood can become damaged when exposed to excessive heat When using the cooker hood over a gas hob ensure that any burners in use are always covered by a pan Switch the cooking zone off when a pan is removed even for a short time
34. on anr s are nn cit eee 54 Warning and Safety instructions This appliance complies with all relevant local and national safety requirements Inappropriate use can however lead to personal injury and damage to property To avoid the risk of accidents and damage to the appliance please read these instructions carefully before using it for the first time They contain important notes on the safety installation use and maintenance of the appliance Miele cannot be held liable for non compliance with these instructions Keep these instructions in a safe place and ensure that all users are familiar with the contents Pass them on to any future owner of the appliance Correct application This cooker hood is intended for use in domestic households and similar working and residential environments gt The cooker hood is not intended for outdoor use It must only be used as a domestic appliance to extract vapours and remove odours from cooking Any other usage is not supported by the manufacturer and could be dangerous The cooker hood can only be used by people with reduced physical sensory or mental capabilities or lack of experience and knowledge if they are supervised whilst using it or have been shown how to use it in a safe way and recognise and understand the consequences of incorrect operation Warning and Safety instructions Safety with children Children under 8 years of age must be kept away from
35. ooker hood to the socket in the ceiling With air extraction mode flexible ducting is also required Exhaust connection 150 mm 34 Installation Safety distance between hob and cooker hood S When planning the installation height of your cooker hood the minimum safety distance between the top of a cooker or hob and the bottom of the cooker hood is as follows unless a greater distance is specified by the manufacturer of your cooking appliance See Warning and Safety instructions for further information Cooking appliance Minimum distance S Electric hob 450 mm Electric grill deep fat fryer electric 650 mm Multi burner gas hob 650 mm total output lt 12 6 kW no burner gt 4 5 kW Multi burner gas hob 760 mm total output gt 12 6 kW and lt 21 6 kW no burner gt 4 8 kW Multi burner gas hob Not possible total output gt 21 6 kW or multi burner gas hob where one burner gt 4 8 kW Single burner gas hob output lt 6 kW 650 mm Single burner gas hob output gt 6 kW and lt 8 1 kW 760 mm Single burner gas hob output gt 8 1 kW Not possible The fully lowered canopy must not go below the minimum distances given 35 Installation Installation recommendations When deciding on the safety distance between the hob and cooker hood please note that a distance of 650 mm above electric cookers hobs may be preferable to give more working space under the ho
36. or 56 Technical data Data sheet for domestic cooker hoods In acc with delegated regulation EU No 65 2014 and regulation EU No 66 2014 MIELE Model name identifier DA 424 V 6 Annual Energy Consumption AEC ooa 36 4 kWh year Energy efficiency class A most efficient to F least efficient A Energy efficiency index EEl ooa 45 7 Fluid Dynamic Efficiency FDE o4 35 5 Fluid Dynamic Efficiency class A most efficient to G least efficient A Lighting Efficiency LEyooa 33 3 Ix W Lighting Efficiency class A most efficient to G least efficient A Grease Filtering Efficiency 95 1 Grease Filtering Efficiency class A most efficient to G least efficient A Airflow at best efficiency point 318 9 m3 h Air flow min speed 220 m3 h Air flow max speed 460 m3 h Air flow intensive or boost setting 700 m h Max air flow Qua 700 m h Air pressure at best efficiency point 421 Pa Airborne acoustical A weighted sound power emissions min speed 48 dB Airborne acoustical A weighted sound power emissions max speed 62 dB Airborne acoustical A weighted sound power emissions intensive or 72 dB boost setting Electrical power input at best efficiency point 105 0 W Power consumption in off mode P W Power consumption in standby mode P 0 15 W Nominal power of lighting system 12 0 W Average illum
37. p com See Technical data for type and reference number Fitting replacing a charcoal filter m Before fitting or replacing a charcoal filter the grease filters must first be taken out see previous section for instructions on how to do this m Take the charcoal filter out of its packaging dai3320 m Press the charcoal filter into the frame m Replace the grease filters m When fitting for the first time activate the operating hours counter see Operation Cleaning and care When to change the charcoal filter m Always replace the charcoal filter when it no longer absorbs kitchen odours effectively It should however be replaced at least every 6 months The charcoal filter operating hours symbol will light up to remind you to change the charcoal filter regularly m The charcoal filter operating hours counter needs to be activated before using for the first time see Operation Resetting the charcoal filter operating hours counter After changing the charcoal filter the operating hours counter needs to be re set m To do this with the fan switched on press the operating hours control 8 once then press it again and hold it for approx 3 seconds until only the 1 is flashing The charcoal filter symbol will go out If you want to clean the charcoal filter before the operating hours counter has reached its maximum m Press the operating hours control 8 once then pr
38. sition of the data plate iissa neiaint aiian aa aa aiia 32 Installation nie 33 Sae Aee e MEOPPRRBREFPERER FEHRCEPEEGEPTERFERTTTHEREPUPFFETFFEUPLEIRLEFLPEFFERTEBESEPFEIFFEUEFIEREFELPEERR 33 ASSEMDIY Darts iaria ie een A ANER A RAA 33 2 Contents Appliance dimensions 244444444400nnannnnnnnnnnnnnnnnnnnnnnnannnnnnnnnnnnnnnnnnnannnnnnnn anne 34 Safety distance between hob and cooker hood S 0ssrssnnnnonnnnnnnnennnnnnnn 35 Installation recommendations 404400nnnnnnnnnnnnnnnnnnnnnennannnnnnnnnnnnnnnn nn 36 Protective foile aee ERS a a SER ESTRRERRERSTEFEIEERERSHFTISEREFEEFRELSTEELHBPHFFFERR 36 Connection for air extraction usssnnnnnnnnnnnnnnnnnnnnnannnnnnnnnnn nn 49 hs 21g ote gener eer cerererrecreer terre trent Serre err cere rer rerecen Cerereectrr terran tere EHE erreree ter EEE 50 Electrical connection u un en 51 Activating Con ctivity 2 O usuussns4snnnnnnnnnnnnannnnnnnnnnnnnnnnnnnnnnannnnnnnnnnnnn 52 Installing the Con ctivity 2 0 Stick 22uursernnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn ann 52 Activating GON CHVILY 2 0 u nennen 52 Activating the Cooker h00d een een 52 Activating the hob een 53 Activation failed 4244444444444Hannnnnannnannnnnnnnnnnnannnnnnnnnnnnnnnnnnannnannnnnnnnnnnnn 53 Deactivating Con ctivity 2 0 zeiten 53 Technical data en ie 54 Gonformitydetlarati
39. system 12 0 W Average illumination of the lighting system on the cooking surface 400 Ix Time increase factor 58 United Kingdom Miele Co Ltd Fairacres Marcham Road Abingdon Oxon OX14 1TW Customer Contact Centre Tel 0330 160 6600 E mail mielecare miele co uk Internet www miele co uk Australia Miele Australia Pty Ltd ACN 005 635 398 ABN 96 005 635 398 1 Gilbert Park Drive Knoxfield VIC 3180 Tel 1300 464 353 Internet www miele com au China Miele Shanghai Trading Ltd 1 3 Floor No 82 Shi Men Yi Road Jing an District 200040 Shanghai PRC Tel 86 21 6157 3500 Fax 86 21 6157 3511 E mail info miele cn Internet www miele cn Miele Hong Kong Limited 41 F 4101 Manhattan Place 23 Wang Tai Road Kowloon Bay Hong Kong Tel 852 2610 1331 Fax 852 2610 1013 Email mielehk miele com hk India Miele India Pvt Ltd Ground Floor Copia Corporate Suites Plot No 9 Jasola New Delhi 110025 Tel 011 46 900 000 Fax 011 46 900 001 E mail customercare miele in Internet www miele in Ireland Miele Ireland Ltd 2024 Bianconi Avenue Citywest Business Campus Dublin 24 Tel 01 461 07 10 Fax 01 461 07 97 E Mail info miele ie Internet www miele ie Manufacturer Miele amp Cie KG Carl Miele StraBe 29 33332 G tersloh Germany Malaysia iele Sdn Bhd Suite 12 2 Level 12 enara Sapura Kencana Petroleum Solaris Dutamas No 1 Jalan Dutamas 1
40. the connection data on the data plate voltage and frequency match the mains electricity supply This data must correspond in order to avoid the risk of damage to the appliance Consult a qualified electrician if in any doubt gt Do not connect the appliance to the mains electricity supply by a multi socket unit or an extension lead These are a fire hazard and do not guarantee the required safety of the appliance For appliances with an external motor fitted EXT models the connection of the two units must be made using the connection cable and the plug connectors These models may only be combined with a Miele external motor Warning and Safety instructions gt For safety reasons this appliance may only be used after it has been built in gt The cooker hood must not be used in a non stationary location e g on a ship gt Tampering with electrical connections or components and mechanical parts is highly dangerous to the user and can cause operational faults Only open the housing as described in the instructions given in the installation sheet and in the Cleaning and care section of this booklet Under no circumstances should any other parts of the housing be opened Miele can only guarantee the safety of the appliance when genuine original Miele replacement parts are used Faulty components must only be replaced by Miele spare parts During installation maintenance and repair work the appliance must b
41. the cooker hood unless they are constantly supervised Children 8 years and older may only use the cooker hood unsupervised if they have been shown how to use it safely and recognise and understand the consequences of incorrect operation Children must not be allowed to clean or maintain the cooker hood unsupervised gt Please supervise children in the vicinity of the cooker hood and do not let them play with it gt Danger of suffocation Packaging e g plastic wrappings must be kept out of the reach of babies and children Whilst playing children could become entangled in packaging or pull it over their head and suffocate Warning and Safety instructions Technical safety gt Unauthorised installation maintenance and repairs can cause considerable danger for the user Installation maintenance and repairs must only be carried out by a Miele authorised technician A damaged appliance can be dangerous Check it for visible signs of damage Do not use a damaged appliance gt The electrical safety of this appliance can only be guaranteed when correctly earthed It is essential that this standard safety requirement is met If in any doubt please have the electrical installation tested by a qualified electrician Reliable and safe operation of this cooker hood can only be assured if it has been connected to the mains electricity supply Before connecting the appliance to the mains supply ensure that
42. the safety screw for the tower on the inside of the frame dai3173t dai3173u m Push the tower and the telescopic piece upwards and bend the retaining tabs outwards again to prevent the tower and telescopic piece from slipping down again 46 m Fit the four telescopic piece clamps between the tower and the telescopic piece The internal telescopic piece rests on the clamps When the screws are tightened the clamps spread out and push the telescopic piece upwards Tighten the screws only until the top edge of the telescopic piece is evenly aligned with the ceiling or the spacer frame Installation N dai3173v m Hold the tower securely bend back the retaining tabs and carefully lower the tower The tower will locate in the cut out in the canopy 1x mmpT20 M4x16 m Insert the safety screw on the inside dai3173w 1x EAA DKF 12 1 dai3173x m With recirculation mode UL cooker hoods insert the charcoal filter 47 Installation dai3173y DA 420V 6 3x DA 424V 6 6x m Carefully remove the protective foil from the grease filters m Replace the grease filters 48 Connection for air extraction A If this cooker hood is used at the same time as a heating appliance that relies on oxygen from the same room there is a risk in certain circumstances of toxic
43. the top of the cooker or hob and the bottom of the cooker hood given in the Installation section must be maintained unless the hob manufacturer states that a greater distance is required If more than one cooking appliance is fitted beneath the cooker hood and they have different minimum safety distances to the cooker hood select the greater distance gt The distances given in Installation must be observed when fitting the cooker hood 11 Warning and Safety instructions gt Metal parts can have sharp edges which may cause injury Wear gloves to protect your hands from being cut gt Exhaust ducting must be of non inflammable material Suitable material is available from Miele specialist dealers or the Miele Spares Dept gt The appliance must not be connected to a chimney or flue which is in use Neither should it be connected to ducting which ventilates rooms with fireplaces gt If exhaust air is to be extracted into a chimney or ventilation duct no longer used for other purposes seek professional advice Cleaning and care gt Do not use a steam cleaning appliance to clean this appliance The steam could reach electrical components and cause a short circuit Accessories gt Only use genuine original Miele accessories with this appliance Using accessories from other manufacturers will invalidate the guarantee and Miele cannot accept liability 12 Caring for the environment Disposal of the pac
44. ting IS m For a lower power level press the control or for a higher level Reducing power on the intensive setting If Power management is activated default the fan automatically switches to level 3 after 5 minutes Selecting the run on time It is advisable to run the fan for a few minutes after cooking has finished to neutralise any lingering vapours and odours in the air With the run on option the fan switches itself off automatically after a pre selected time m After you have finished cooking press the run on option control 5 A15 Once the fan will switch itself off after 5 minutes 5 lights up Twice the fan will switch itself off after 15 minutes 15 lights up If you press the run on option control 5 415 again the fan will remain on 5 amp 15 will go out Switching the fan off m Use the On Off control to switch the fan off The D symbol will go out 21 Operation Manual mode Dimming switching the hob lighting on off The hob lighting can be switched on and off and dimmed independently of the fan m Press the lighting control briefly to switch it on and off The lighting will switch on at maximum brightness m With the hob lighting switched on press and hold the hob lighting control in The brightness will gradually dim until you release the control m Press the lighting control O in again to increase the brightness to the
45. tting when necessary When a large volume of cooking vapours are being produced switch to a high power level in good time This is more efficient than operating the cooker hood for longer to try to capture cooking vapours which have already been distributed throughout the kitchen Cleaning and care Casing General information The surfaces and controls are susceptible to scratches and abrasion Please observe the following cleaning instructions m All external surfaces and controls can be cleaned using hot water with a small amount of washing up liquid applied with a well wrung out soft sponge or cloth Do not let moisture get into the cooker hood Only use a damp cloth when cleaning This is particularly important around the controls m After cleaning wipe the surfaces dry using a soft cloth Do not use cleaning agents containing soda acids chlorides or solvents abrasive cleaning agents e g powder cleaners or cream cleaners and abrasive sponges as well as pot scourers or sponges which have been used previously with abrasive cleaning agents These will damage the surface material Important for appliances with stainless steel surfaces This information does not apply to the controls m Stainless steel surfaces can be cleaned with a proprietary non abrasive cleaning agent designed specifically for use on stainless steel m To help prevent re soiling a proprietary conditioning
46. ust be directed in the flow direction of the flue m When ducting is horizontal it must be laid to slope away at at least 1 cm per metre This is to ensure that condensate cannot drain back into the appliance m If the exhaust ducting is to run through rooms ceiling space etc where there may be great variations in temperature between the different areas the problem of condensation will need to be addressed The exhaust ducting will need to be suitably insulated 49 Connection for air extraction Silencer dai2003 To achieve even further reductions in noise levels a special silencer optional accessory can be fitted in the ducting system Extraction mode dai3286a The silencer not only reduces noise from the motor outside the house but also sounds from outside e g traffic noise For this reason the silencer must be positioned as close as possible to the ducting exit 50 Extraction mode with external motor um Pa un N gt aitete dai3286d To minimise noise from the motor in the kitchen the silencer should be positioned in front of the external motor if possible or if the ducting is long above the exhaust socket on the cooker hood In the case of an external motor located inside the house fitting a silencer behind the external motor reduces the noise of the motor o
47. utside the house Electrical connection All electrical work should be undertaken by a suitably qualified and competent person in strict accordance with current national and local safety regulations BS 7671 in the UK Installation repairs and other work by unqualified persons could be dangerous for which the manufacturer cannot be held liable Ensure power is not supplied to the appliance until after installation or repair work has been carried out Do not connect the appliance to the mains electricity supply by an extension lead These do not guarantee the required safety of the appliance The connection data is given on the data plate This is visible when the grease filters have been removed Ensure that this data matches the household mains supply Connection of this appliance should be made via a suitable isolator or a double pole fused spur connection unit which complies with national and local safety regulations and the On Off switch should be easily accessible after the appliance has been built in When switched off there must be an all pole contact gap of 3 mm in the switch including switch fuses and relays according to EN 60335 If the switch is not accessible after installation depending on country an additional means of disconnection must be provided for all poles For extra safety it is advisable to protect the appliance with a suitable residual current device RCD Contact a qualified electricia
Download Pdf Manuals
Related Search